Search Documents

By John Dasher

Extrapolation is a useful technique, but it can be overdone. Seldom is it justified to study over a range of 1 to 6 and extrapolate the results to 150,000. It is especially dangerous if the extrapolation is based on a false assumption. The authors assume settlers scale-up by residence time rather than by area, admit their result (a settler depth of 7 m) is "unreasonable" and suggest longer, wider, shallower settlers might be better. Various authors have noted for a copper-LIX system a total flow basis of 2 gpm per sq ft for sizing settlers. The results of this are compared with those in the paper in [Table 7]. The authors note that flooding of their settlers was never approached. Thus the smallest unit calculated is understandably twice too big. The largest however, is 5% of the required size. I note that the figures in [Table 6] for 1/min/cm2 are based on plan area rather than cross section as titled and are wrong by l0 4. A flow of 2050 1/min/cm2 is about Mach I. It is also 10 5/3 or 46.5 times that of the little one, although the abstract says the design was based on constant flow rate per unit cross section.

Jan 1, 1977

By John Dasher

Getting spodumene to float quickly and cleanly can be a problem. The author has presented an excellent account of a valid and useful approach to the scale-up of such problem floats. This indicated advantages for doubling retention time, i.e., buying another set of flotation cells. The author states that 21 pct of the spodumene floated in 2 min in the laboratory cell, that the grade of the rougher was about 75 pct spodumene, and that the final tailing contained 4 to 12 pct spodumene in different sizes with the present cells and 1 to 9 pct spodumene with twice as many cells.

Jan 6, 1959

This excellent paper by Dr. Colombo parallels quite closely the bench and pilot work done by the Hanna Research Laboratory on the Mesabi oxidized taconites. Because of the vast reserves and future ore requirements the need to perfect the selective flocculation-flotation process becomes very necessary. The selective flocculation process is a very efficient method of desliming, leaving a fairly clean, upgraded product for flotation. However, one of the problems that we have encountered in this process was some very fine, -2 micron liberated goethite in the slimes that did not flocculate. The complete slime removal is not necessary. We remove slimes to the extent of about 5% of the iron units. However, on difficult treating ores we would remove more slimes. The reclaimed water from our pilot plant has a turbidity of about 1000-3000 ppm. We can obtain lower turbidity water but to do this would involve additional lime as a tailing flocculant and we would run the risk of flocculating the entire ground pulp in the selective flocculation process because of the increased Ca level in the water. We have about seven different geological ore types out of 17 recognizable ore types that are treatable. All of these ore types require different degrees of dispersion and grinding which is a problem. The use of acrylic acid polymers as a selective flocculant has been patented by the American Cyanamid Co. This will-have to be

Jan 1, 1979

This excellent, concise paper by Dr. Iwasaki on the principles of selective flocculation for iron ores discusses many of the principles and problems which have occurred in our bench and pilot plant test-work. The use of sodium tripolyphosphate in combination with sodium silicate as a dispersant is very effective. However, this may cause a problem with the environmental groups as phosphorous is a nutrient. We have also established that the lower the Ca level in the pulp solutions the greater the dispersion. We have found that ores from the same geological strata, having the same general mineralogy and iron content will sometimes have widely different degrees of dispersion. There was-no difference in the gross mineralogy but the solubility of the Ca and SO ions was much less in the ores most easily dispersed. Research efforts should be directed towards a more practical means which would more easily enable one to predict the amount of dispersant required for the various ores. With regard to water quality we have found that waters having higher contents of SO4 and C1 ions hinder dispersion. This could be a method of controlling too much dispersion by the addition of sulfate or chloride ions. This would require further investigation. We have had no trouble with agitation speeds of up to 925 rpm in conditioning starch with the dispersed pulp prior to selective flocculation. We have found about 0.3Lb/LT of starch to be sufficient for selective flocculation on our ores. The increasing of the starch to 1.25Lb/LT has had no effect on the metallurgy of the selective floccula-

Jan 1, 1979

Insoluble slimes are present in nearly all sylvinite ore bodies and must be removed prior to potash flotation because they adsorb excessive amounts of potash flotation reagents and cause low potash recoveries and grades. The problems associated with insoluble slimes will become more pronounced as high grade-low insol potash ores are depleted and lower grade ores containing high insols are processed. The most common commercial practice for insoluble slimes removal is mechanical desliming (hydroclassification); however, most of these desliming circuits were designed to treat sylvinite ores containing less than 4 percent insoluble slimes. As Mr. Banks mentioned in his presentation, higher insoluble slimes concentrations (>4 pct) in the mill feed overtax the mechanical desliming circuit and result in excessive brine and potash losses. Increasing the capacity of the circuit would require redesigning of the entire potash circuit and additional costly equipment. Because of mineralization and liberation properties of the high insols sylvinite deposits, the expansion of the desliming circuit may not economically maintain high potash grades and recoveries. Selective flocculation-flotation is an excellent alternative for removing insoluble slimes from potash ores. Cominco's ore, containing 4.5 to 8 percent insoluble slimes, is particularly amenable to the slimes flotation process, probably because of the absence of expanding-type clays such as montmorillonite. The overall potash recovery of 86 percent and low slime flocculant and collector dosages of 0.03 to 0.04 pound reagent per ton of feed is good evidence of the success of the process. If appreciable montmorillonite were present, the metallurgy would not be as favorable and reagent consumptions would increase significantly.

Jan 1, 1979

My question relates to tundish nozzle plugging on aluminum-killed heats. North Star has avoided this problem by silicon deoxidation. What has been Inland's experience with this problem on open-pour and submerged nozzle pouring?

Jan 1, 1972

The evaluation of suppliers of BOP linings included only magnesitic and periclase compositions. Ford utilizes some dolomitic compositions. Do you care to comment on this subject?

Jan 1, 1972

By G. C. Waterman, W. E. Hawes

Mr. Grieves' paper on "Shaft Sinking Today --A Boring Business Tomorrow" in the Dec. 1981 issue of MINING ENGINEERING is an excellent description of recent improvements in speed and costs of shaft sinking. However, shaft boring techniques are not a recent development. In 1935-36, the Idaho Maryland Co. (gold), Grass Valley, CA, bored the vertical 1.5-m-diam Idaho No. 2 ventilation and supply shaft to a depth of 346 m. The equipment was designed and perfected by Branner Newsome and was, I believe, described in "Transactions." Pickands Mather later bored a 1.8-m-diam shaft to a depth of about 305 m using Newsome's design. The Idaho No. 2 shaft cut through hard gabbro, diabase dikes, soft serpentine, very incompetent ankeritized serpentine and a strong fault zone. The completed shaft did not require timber support; the fault zone was cemented. Equipment consisted of a rotating 1.5-m or 3-m core barrel with a slotted bottom which cut a 76-mm kerf. The cutting agent was chilled steel shot introduced into the slot as needed. The driving mechanism and core barrel were lowered into the shaft, the former secured to the wall and the inshaft "engineer" operated the motors which controlled core barrel rpm and advance. After an advance of 1.5-3 m the equipment was lifted out of the shaft, a half(?) stick of powder cut off the drilled core, and it was hoisted to the surface with a cable attached to an eye bolt at the tope of the core. A "shift" consisted of three men: hoistman, equipment operator (down the shaft), and a surface laborer. Advance was variable as equipment and techniques were perfected. Near the end of the job advance was, as I remember, 1.5-3 m per shift. Costs were, as I recall, about $115/m. Up to 4 m cores were lifted out in one piece and swung to the dump by a stiff leg derrick. The Newsome equipment was relatively inexpensive to build and operate and his method should be (more than?) competetive with the methods described by Grieves.

Jan 1, 1983

By Maurice Grieves

GC. Waterman Mr. Grieves' paper on "Shaft Sinking Today--A Boring Business Tomorrow" in the Dec. 1981 issue of MINING ENGINEERING is an excellent description of recent improvements in speed and costs of shaft sinking. However, shaft boring techniques are not a recent development. In 1935-36, the Idaho Maryland Co. (gold), Grass Valley, CA, bored the vertical 1.5-m-diam Idaho No. 2 ventilation and supply shaft to a depth of 346 m. The equipment was designed and perfected by Branner Newsome and was, I believe, described in "Transactions." Pickands Mather later bored a 1.8-m-diam shaft to a depth of about 305 m using Newsome's design. The Idaho No. 2 shaft cut through hard gabbro, diabase dikes, soft serpentine, very incompetent ankeritized serpentine and a strong fault zone. The completed shaft did not require timber support; the fault zone was cemented. Equipment consisted of a rotating 1.5-m or 3-m core barrel with a slotted bottom which cut a 76-mm kerf. The cutting agent was chilled steel shot introduced into the slot as needed. The driving mechanism and core barrel were lowered into the shaft, the former secured to the wall and the inshaft "engineer" operated the motors which controlled core barrel rpm and advance. After an advance of 1.5-3 m the equipment was lifted out of the shaft, a half(?) stick of powder cut off the drilled core, and it was hoisted to the surface with a cable attached to an eye bolt at the tope of the core. A "shift" consisted of three men: hoistman, equipment operator (down the shaft), and a surface laborer. Advance was variable as equipment and techniques were perfected. Near the end of the job advance was, as I remember, 1.5-3 m per shift. Costs were, as I recall, about $115/m. Up to 4 m cores were lifted out in one piece and swung to the dump by a stiff leg derrick. The Newsome equipment was relatively inexpensive to build and operate and his method should be (more than?) competetive with the methods described by Grieves. W.E. Hawes The author, in mentioning the South African developments of the cactus grab, ignores the parallel development of the Cryderman mucker in this hemisphere. Perhaps a slightly longer history of blind hold drilling would have been in order. Blind shaft boring got a major boost at the Nevada Test Site, as part of the nuclear weapons development, when it was essential to be able to quickly assess depth for weapons testing. One of the early civilian attempts to utilize this technology occurred when Kerr McGee drilled the shaft at the Section 19 Mine at Ambrosia Lake, NM. This twin masted drill rig belonged to a subsidiary of Kerr McGee, not Shaft Drillers. This was a difficult hole, due to bentonitic shales that decomposed. Later advances in drilling fluids eliminated this problem. The Conoco project referred to is not entirely correct, and needs minor amplification: The depth of the development (not pilot) shaft drilled was 684 m, at a diameter of 3.05 m, with a 2.16 m ID hydratatic casing being installed to a depth of 669 m. Conoco Inc., not Challenger, executed the drilling, however Conoco did use Challenger Drilling Company's Rig 14-S. Rig 14-S is unique in that it is specifically designed for shaft drilling, rather than being an oil field rig used for this service. All work was planned and directed by Conoco personnel. Deviation of the aforementioned shaft from vertical was 31 cm. Two smaller shafts (pilot shafts) were drilled with the same rig. These smaller ones were drilled 1.8 m in diameter, to depth of 665 m and cased with .91-m-diam casing, to depth of 650 m to be used as pilot holes for 5.5 m diameter shafts. The total elapsed time for all drilling, casing, cementing, and rig moves was 50 weeks. The constraints mentioned of vertical accuracy, torque, wall collapse, rig set up time, lining time etc., pumping out, etc., may not be as serious as the author implies. First, vertical accuracy: The record achieved by Conoco indicates that with reasonable care, good accuracy can be obtained, primarily by having a fair amount of weight in tension, rather than on the drill bit. Second, the amount of torque that can be applied to the drill stem has been greatly increased by the introduction of larger diameter drill stems, such as the new Hughes rig uses. Third, risk of collapse of shaft walls is minimal with the proper mud program. Basically, the walls are supported by the weight of the mud and it is not removed until some type of casing is installed and grouted in. Here in the real challenge of blind drilling shafts to devise a more economical method of lining bored shafts than using steel casing. The remaining issues were minor at Conoco, provided adequate planning and scheduling takes place. An excellent paper, "Shaft Drilling--Crownpoint Project" by Hassell H. Hunter, presented at the Fifth Uranium Symposium in Albuquerque in Sept. 1981 contains details of this project. A combination of blind boring, with enlargement by either mechanical means (boring machine, or tunneling type shield) or slabbing down, with muck removal through a larger bored shaft would seem to be the future trend in shaft development. The economics, especially for wet conditions, favor this concept over conventional sinking, as has been demonstrated at Kerr McGee --Churchrock, UNC--Churchrock and Conoco at Crownpoint.

Jan 3, 1983

By R. W. Barbaro, R. V. Ramani, K. V. K. Prasad, P. T. Luckie

Discussion by A. Unal Barbaro et al. (1990) implemented a tedious study aimed at delineating the short-scale spatial variability of sulfur in a coal seam. It is not possible, however, to extend their conclusions to any other coal seam or use their in any other fashion, because the background geology was not presented. Nor were the conclusions accompanied by geological interpretations in the paper. In addition, an unfortunate printing error occurred where the total sulfur (determined by High Temperature Combustion) variogram in Fig.3 was duplicated in Fig. 2 instead of the seam height variogram. A more serious error, however, has been committed in the definition of the variable, seam height. What is defined as seam height by Barbaro et al. (1990) is, in essence, mining height, and is not a regionalized variable that should be studied by geostatistical methods directly. Despite the fact that the variable, seam height, is not defined in the paper explicitly, the following quotation discloses the fallacy: "All roof rock that exceeded 1.8 m (6 ft) from the floor was not taken because the longwall was operated to not mine more than 1.8 in (6 ft) unless the coal seam height exceeded 1.8 m (6 ft)." From this definition, the seam height, and therefore the sampling height, is equal to the actual coal thickness, if the coal thickness is greater than 1.8 m (6 ft). Otherwise, it is equal to the sum of the coal thickness plus the thickness of the roof rock that complements the thickness to 1.8 m (6 ft). In the latter case, the seam height is constant and equal to 1.8 m (6 ft). It is possible to conduct a variogram study on a pool of samples that are realizations of two different variables. But the conclusions derived would not belong to any one of the two variables uniquely and, therefore, do not possess any significance. Geostatistical analysis is irrelevant for the sum of multiple regionalized variables formed by arbitrary selections. In a two-seam setting, for example, the mining height, as defined by the thickness of one seam at one location and the thickness of both seams at another location (due to quality and/or minimum thickness considerations perhaps), should not be used in the calculation of one common variogram. The two seams should be modeled separately. They can then be combined according to the specific purposes of the study. On the other hand, if a constant is added to a regionalized variable (to incorporate dilution perhaps), the variogram of the new variable will not change. Barbaro et al. (1990), surprisingly, does not give any geological interpretation of their results despite the fact that most of them can be explained by the origins of sulfur in a coal seam. The presentation of the results of a geostatistical study with no reference to the geology of the deposit is uninformative. It may also be misleading for the potential users of geostatistics, It is not unusual to find nuggets of pyrite in coal seams. In such cases, pyritic sulfur will probably display a spatial structure for only a very small distance that will appear in the experimental variogram as no spatial correlation. This very well known phenomenon is called the pure nugget effect in geostatistics (Journel and Huijbregts, 1978) and perhaps can explain the lack of correlation found for pyritic sulfur content. The lack of correlation found for the total sulfur content may also be explained in the same way because the total sulfur content is dominated by the pyritic sulfur content in this case study. One should notice, however, that the situation may completely be reversed after cleaning the coal. Not all of the inorganic sulfur should be expected to be in the form of pyrite nuggets in a coal seam. It may also be disseminated in the coal seam and it is expected that it follows a certain spatial structure. However, an existing spatial structure may be masked by including a part of the roof rock, rich in sulfides, into the seam thickness in an arbitrary fashion because areas having a sandstone roof sometimes are known to show a higher sulfur content due to the downward percolation of solutions rich in iron sulfides (Clark, 1979). Plants use sulfur in their growth processes. Much of this sulfur is bound organically during peat accumulation and coal formation (Cecil et al., 1978.) This suggests a spatial structure of some sort for the organic sulfur. However, it is not possible to test this hypothesis because the results obtained by the authors for the organic sulfur content are not given in this paper. For this reason, the conclusion that simple average of the nearby samples would provide the best unbiased estimates is questionable for organic sulfur and is not based on any substantial supporting evidence. It is suspected that no spatial structure was detected and this was due to high sampling and laboratory analysis errors. Before concluding that sulfur variability in the seam at the location of study was random, a more detailed study for the disseminated non-pyritic sulfur should have been conducted, not for the sake of scientific curiosity only, but also due to its utmost importance with regard to coal cleaning and emission control. Pyritic sulfur can be cleaned to a considerable extent, whereas organic sulfur can not, making the emission control strategies highly dependent on the spatial distribution of the organic sulfur (Knudsen, 1981). In the light of these facts, one wonders why Barbaro et al. (1990) did not present the results of their study for the sulfate and organic sulfur content. References Barbaro, R.W.. et al., 1990, "Short-Scale Spatial Variability of Sulfur in a Coal Seam,' Mining Engineering, Vol. 42, No. 11, pp. 1267-1269. Cecil, C.B., et al., 1978, "Geology of Ccontaminants in coal," report prepared for Environmental Protection Agency, North Carolina, 123 pp. Clark, W.J.. 1979, "An interfluve model of the upper Freeport coal Bed in part of western Pennsylvania," unpublished MS thesis, University of South Carolina, 57 pp. Journel, A.G., and [Huijbregls], Ch. J., 1978, Mining Geostatistics, Academic Press, London, 600 pp. Knudsen, H.P., 1981. "Development of a Conditional simulation model of a coal deposit," unpublished PhD dissertation, The University of Arizona, 109 pp.

Jan 1, 1992

By Stephen Semeniuk

Discussion by Stephen Semeniuk Discussion As a valuator and SME member, I view Ross D. Lawrence's position as based on unproven and faulty assumptions made with regard to the pragmatic evidence presented in his paper. Moreover, his call for the inclusion of all mineral resources in discounted cash flow valuations is redundant, if not irrelevant, as there are procedures that already take all classes of mineralization into consideration for valuation purposes. In my experience as a valuator, I find that Canadian securities regulators are more than accommodating in allowing any valuations of mineral properties to be based on cash flow calculations. In other business areas, the same regulators usually reject discounted cash flow valuations of projects or businesses with no operating history. Instead, the regulators prefer valuations to be based on other transactions tested in the marketplace. Valuations based on actual market transactions are less subjective than discounted cash flow calculations and/or the capitalization of arbitrary, untested or undemonstrated earnings projections. In the mining and minerals sector, such projections may be made by persons not qualified to make such projections. In support of this statement, I direct readers to the article "Valuation of mineral properties which do not contain exploitable reserves" by Lionel C. Kilburn, which appeared in the August 1990 issue of the CIM Bulletin. To quote from the article: "Value of a mineral property depends basically upon metal prices, recoverable grades, mining and metallurgical practices, commodity supply and demand, and political-economic conditions, all of which vary with time. Five fields of expertise influence the value of a mineral property: •geological engineering, •commodity markets, •financial markets, •stock markets and •mineral property markets. The skills of geologists and engineers properly apply to the first field of expertise. Knowledge and consideration of the other four fields is important, but such advice is more properly sought from marketing experts, economists and stockbrokers." Securities regulators have created no hardship for valuators by excluding unsubstantiated resources in discounted cash flow valuations. In the field of engineering, best design practices apply. A margin of safety is built into the design criteria for any new equipment or structure that will exceed normally expected load levels and stresses, even though such considerations imply higher front end costs. In accounting, the comparable operating principle is conservatism. It explains why, for balancesheet presentation purposes, inventory is stated at cost or market, whichever is the lowest value. Similarly, when the engineering or geoscience-based valuator plays in the field of finance, the rules of accounting and applied economics apply. Regulators in their skepticism of income-based valuations are in tune with similar views already expressed in mining literature. To quote H. Van Tingley, in Mining Magazine, July 1996: "... the DCF method has inherent dangers when applied to undeveloped resources. Firstly, it presents an often-undeserved aura of accuracy. A DCF value is no more accurate than the least accurate of the assumptions incorporated into the calculation - and assumptions

Jan 1, 2003

We did install one 100% brick bottom in our #33 furnace which is basically the same design as Inland's furnace. We had previously embarked on a program of replacing all bottoms in our 300 ton furnaces every 2nd campaign which would be about every 2000 - 2300 heats. This had been necessitated by the effect of our rather high oxygen blowing rates and our desire to maintain a minimum bottom interval level. This meant that we were able to compare bottom performance of various types of materials on a realistic bas is. Since furnace availability is critical to our operation, we are organized to employ every piece of equipment and all the necessary man power to complete a rebuild in the shortest possible time. A 300 ton furnace requires 7.5 days to rebuild. If a new bottom is to be installed an additional 2.5 days is added - 24 hours for tear out and 36 hours for bricklaying - making a total of 10 days.

Jan 1, 1972

I strongly endorse Mr. Jackson's (Inland Steel Company) oral comment on the authors' paper that, as blast furnace slag is removed from the BOF charge, lime solution may be retarded. After two or three pourings, the blast furnace slag will contain some iron oxide and considerable manganese oxide, and it is hot and possibly still liquid. A few thousand pounds of this slag will speed up the slag development rate considerably and could be considered a good auxiliary flux. Although the removal of blast furnace slag from the BOF charge lowers the total sulfur load by 40 to 50%, we must have a good, quick slag development in the BOF to bring .030 to .035% sulfur hot metal to .020%, a requirement on a high percentage of our steels today. In discussions at off-the-record meetings and one not published at last year's annual meeting as well as discussions with many operators over the past 1-1/2 years, I predicted that the removal of blast furnace slag could slow down lime dissolution and that, if a shop had dissolution problems before, the problem could be quite serious.

Jan 1, 1972

By E. Arioglu

Discussion by E. Arioglu Y. Luo and S.S. Peng are to be congratulated for their outstanding paper providing new results from surface subsidence monitoring over longwall panels under different conditions. This writer found the authors' paper very interesting. In reference to this paper, the following contributions are offered: • In the paper, the maximum possible subsidence [(ASmax)] induced by chain pillar convergence has been related to a parameter (h/1- p) by linear regression. (Notations are expressed in this discussion's Fig. 1 (b).) It is a well-known fact that in a goaf the roof lowers onto broken material that gradually compacts. Then the physical behavior of goat may closely follow the compaction characteristics of broken materials. In light of this assumption, a mathematical means (Fig. 1(a)) of defining the expected compaction (i.e. surface subsidence) represents an exponential expression between [ASmax/m vs. h/1-p]. This is based on Luo and Peng's field observations from the Appalachian, Illinois and Alabama coal fields. (The coefficient of regression "r" under consideration was computed to be 0.883). • According to Wardell's (1969) findings for board and pillar mining, the maximum possible subsidence can be expressed in terms of maximum pillar loading (depth, ratio of extraction) and the height-to-width ratio of the pillars left. Using Luo and Peng's 1991 results, this writer discovered a regression equation between the above-mentioned factors. As displayed in Fig. 1(b), the functional expression approximates as closely as possible the observed subsidence data. It may be noted here that Wardell's approach (1969) can be successfully utilized for longwall panels having chain pillars. Reference Wardell, K., 1969, "Ground surface and control," Mining Congress Journal, January, pp. 1-7.

Jan 1, 1993

It was a pleasure listening to this paper. Gary Works' problems were a lot more extensive than the trunnion bearing problems encountered at the Weirton Steel Division. In our two-vessel shop bearing failures are critical in that with a bearing failure on an operating vessel and the second vessel under rebuild, we are down until the vessel rebuild is completed or the bearing is repaired. The first bearing problem at Weirton occurred after we had been operating three years. The failure occurred during the 8th heat following "bum-in" of the vessel. Immediate steps were taken to change the damaged float bearing without an extensive search for the reason the bearing failed. Once the campaign was run out the bearings were inspected and found to be damaged. Field checks revealed that the bearing pedestals were not properly located and as a result the freedom of the float bearing was restricted. The trunnion pin end to end dimension had decreased due to distortion and deflection in the trunnion ring. These dimensions were within tolerances. The damage to our bearing was similar to that in the exhibits from U.S. Steel-Gary Works. Steps taken to correct what was found in the field checks were as follows: 1. The pedestals were relocated to center the bearings. 2. 4" diameter pins were installed to locate the housing in the pedestals. 3. The bearing pedestals were opened up to allow the bearing housing to move slightly in the pedestal. 4. Lubrication fittings for greasing between the bearing housing and the pedestal were installed.

Jan 1, 1972

By A. M. Radigan, W. G. Prast

M.S. Azun The authors' paper did not explain the facts and reasons why state companies are established and what their role is in international industrial mineral trading. Also, I do not agree with the conclusion implying that the main goal for state companies is to capitilize natural resources. Almost all state companies are founded by certain laws and their activities are arranged by state regulations. Their only aim is to operate mineral deposits for their people and to protect the rights of the people. Although some ore deposits, such as nonstrategic or small, may be exploited by privately owned companies, the state has the right to control the operation and production. Activities of state companies may or may not be widened because of the character of the deposits and the importance of the mineral market involved. For some countries, although governments may occasionally change hands, the policy of the mineral trading system is not affected by this change. There is no doubt that any government desires to make more earnings to increase GNP, when it is involved in operating and trading mines. It wants to produce and sell the finished products, instead of unprocessed ones, if possible. When it is known that some mineral deposits are relatively rare, such as Turkish boron deposits, the government can nationalize the mines to control production and affect the market. If there is an abundance of a certain mineral in the market, the government can cut production and set a floor price, such as Canadian potash. Also, when production of a specific mineral is unique, such as Turkish chromite, the price of such mineral may be set by correspondant government. One may add that if some governments with their state companies produce a certain mineral in a larger amount, they may decide to establish a cartel to protect their production and price. These are the facts followed by government-owned state companies and partially government-owned companies. The reason being charge of many deposits by the state companies is always the same: "protect" the mineral rights of the people.

Jan 2, 1984

By M. S. Azun

The authors' paper did not explain the facts and reasons why state companies are established and what their role is in international industrial mineral trading. Also. I do not agree with the conclusion implying that the main goal for state companies is to capitalize natural resources. Almost all state companies are founded by certain laws and their activities are arranged by state regulations. Their only aim is to operate mineral deposits for their people and to protect the rights of the people. Although some ore deposits, such as nonstrategic or small, may be exploited by privately owned companies, the state has the right to control the operation and production. Activities of state companies may or may not be widened because of the character of the deposits and the importance of the mineral market involved. For some countries, although governments may occasionally change hands, the policy of the mineral trading system is not affected by this change. There is no doubt that any government desires to make more earnings to increase GNP, when it is involved in operating and trading mines. It wants to produce and sell the finished products, instead of unprocessed ones, if possible. When it is known that some mineral deposits are relatively rare, such as Turkish boron deposits, the government can nationalize the mines to control production and affect the market. If there is an abundance of a certain mineral in the market, the government can cut production and set a floor price, such as Canadian potash. Also, when production of a specific mineral is unique, such as Turkish chromite, the price of such mineral may be set by correspondent government. One may add that if some governments with their state companies produce a certain mineral in a larger amount, they may decide to establish a cartel to protect their production and price. These are the facts followed by government-owned state companies and partially government-owned companies. The reason being charge of many deposits by the state companies is always the same: "protect" the mineral rights of the people.

Jan 1, 1985

By Bjorn Bolviken

Bjorn Bolviken (Geochemist, Geological Survey of Norway, Trondheim, Norway)-Under the heading "Recognition of Anomalies," the author states, "If the frequency distribution is actually log-normal, the probability of these high values being part of the background population is small (less than 0.023 and 0.0013 for 2 and 3 standard deviation, respectively)." The figures quoted seem to be the probabilities of these high values being the mean rather than part of the background population unless "background" is defined as one single concentration. If the background is considered to be a statistical distribution of concentrations,50 (which is probably the case here since the author uses the term "background population"), the probability of any observed value being part of the background may be estimated through a calculation of the number of observed values that are in excess of (or below) the number expected to belong to the background. Apparently, some confusion exists in the literature regarding this point. Many authors accept the concept of background as being a statistical distribution, but do not seem to recognize the consequences of this concept. One of these consequences would be that the background of a chemical element should comprise any concentration between zero and a theoretical maximum, which is governed by the chemistry and mineralogy of the material

Jan 1, 1974

By J. C. Wynn

J.R. Hillebrand From the abstract, "A realistic ore deposition model to serve as a conceptual framework." Further, on page 246, "The first area of study was the Josephine peridotite, now identified as an ophiolite terrane, located in northern California and south-western Oregon (Fig. 3). Here, it was felt that we could test the models shown in Figs. 1 and 2 and, if successful, expand the model and test it in other chromite districts in the US and around the world." My comments refer only to chromite deposits in Europe and the Middle East. First, I question that may chromite deposits occur in the idealized ophiolite section shown in Fig. 1. Second, although some podiform deposits (referring to morphology) have been important (Guleman, Turkey, for example), the stratiform deposits are of greater importance in tonnage and frequently grade. Examples include Nada, Yugoslavia; Bulqiza, Albania; Xerolivado, Greece; Saranovsk, Russia; and Abdasht, Iran. Reply by J.C. Wynn Mr. Hillebrand raises two issues that deserve a serious response. One issue is basically subjective and the other is ultimately political. First, the question of where (and how many) podiform chromite deposits are found in the idealized ophiolite section of Dickey (1975). The Dickey model is still perhaps somewhat controversial (Panayoutou, 1980), but our experience in the Josephine ophiolite of northern California (Wynn, 1980; and Albers, 1983) shows that the model works well there. Virtually all the chromite is found in dunite lenses in the tectonite peridotite (harzburgite). Since there are few complete ophiolites exposed in the world, the model will probably never satisfy everyone. The degree of acceptance is a function of any individual's subjective experience. Second, it is well known that stratiform chromite contributes more than 95% of the chromite reserves presently known in the world, and it could be reasonably argued that there is no point in exploring for or exploiting podiform deposits further. The title of the paper, however, was in part 'strategic minerals geophysical research'; chromite is considered a strategic and critical mineral of the US and many other industrialized nations. Stratiform deposits in South Africa and Zimbabwe account for most of the chromite reserves in the world. Unfortunately, experience in modern times with substantial price fluctuations and even resource cartels dictates the wisdom of identifying and maintaining a national chromite reserve, irrespective of the cost. An improved exploration methodology is an essential element in this strategic objective. References Albers, J.P., 1983, "Geological and Geophysical Studies of Chromite Deposits in the Josephine peridotite, California and Oregon," US Geological Survey Bulletin 1546 A-D, 118 pp. Dickey, J.S. Jr., 1975, "A Hypothesis of Origin for Podiform Chromite Deposits," Geochimica et Cosmochimica Acta, Vol. 39, pp. 1061.1074. Panayiotou, 1980, Proceedings, International Ophiolite Symposium, Cyprus, 1979, 781 pp. Wynn, J.C., 1980, "Exploration Geophysical Methods and Strategies, and Their use to Locate and Assess Small Mineral Deposits," Chapter 12 of Meyer and Carmen, eds., The Future of Small Scale Mining, McGraw-Hill, New York, pp. 75-83.

Jan 12, 1983

By J. R. Hillebrand

From the abstract, "A realistic ore deposition model to serve as a conceptual framework." Further, on page 246, "The first area of study was the Josephine peridotite, now identified as an ophiolite terrane, located in northern California and southwestern Oregon (Fig. 3). Here, it was felt that we could test the models shown in Figs. 1 and 2 and, if successful, expand the model and test it in other chromite districts in the US and around the world." My comments refer only to chromite deposits in Europe and the Middle East. First, I question that may chromite deposits occur in the idealized ophiolite section shown in [Fig. 1]. Second, although some podiform deposits (referring to morphology) have been important (Gulernan, Turkey, for example), the stratiform deposits are of greater importance in tonnage and frequently grade. Examples include Nada, Yugoslavia; Bulqiza, Albania; Xerolivado, Greece; Saranovsk, Russia; and Abdasht, Iran.

Jan 1, 1984