Search Documents

By J. Evans

INTRODUCTION Section 209(b) of the Federal Land Policy And Management Act of 1976 (FLPMA-43 U.S.C. 1719 b) authorizes the Secretary of the Interior to convey mineral interests owned by the United States where the surface is or will be in non-Federal ownership. The objective is to allow consolidation of surface and subsurface (mineral) ownership. Certain major conditions must prevail for a conveyance to occur. These are: 1) There are no known mineral values (KMV) or 2) Where the mineral reservation interferes with or precludes appropriate non-mineral surface development and that non-mineral development is a more beneficial use of the land than the mineral development. Remember that allegation, hypothesis or speculation that the conditions could or may exist in the future will not be a sufficient basis for conveyance. Convincing factual evidence for an applicant’s case for mineral conveyance must be made in order to achieve that conveyance. See 43 CFR 2720 0-1 to 0-3, and 0-6. CONCEPT OF KNOWN MINERAL VALUES Known mineral values means mineral rights in lands containing geologic formations that are valuable in the monetary sense for exploring, developing, or producing natural mineral deposits. The presence of such mineral deposits with potential for mineral development may be known because of previous exploration, or may be inferred based on geologic information (43-CFR 2720.0-5(b).

Jan 1, 2007

The design and selection of components for belt conveyors is a well known procedure and many handbooks, catalogues and design manuals offer a wide range of detailed information which can be applied to most of the known conveyor problems. The aim of this paper, however, is to investigate the various methods of conveyor drive configurations, and incorporate the latest technical achievements in the control systems, particularly for high capacity conveyor systems carrying ore from pit to processing plants where the lowest maintenance, operating and initial costs are of major importance. Past experience has proven that multi pulley drives can reduce initial capital cost of a conveyor; this leads to the need for better torque control during startup, running, stopping and load sharing. Many methods of torque control are available and have been used in the past. All types have their advantages and disadvantages and must be considered when designing a conveyor or conveyor system. However the recently developed solid state electronic soft start controls utilising AC squirrel cage induction motors are gaining acceptance, especially for a conveyor system where the same control and logic system can be used to transmit startup commands to more than one

Jan 1, 1978

By Ian M. Thomson, Robert W. Greene

Last August, American Commercial Barge Line Co. (ACBL) began moving coal from mines on the old Camp Breckinridge property in Western Kentucky to TVA's new 2600 MW steam plant at Cumberland City, Tenn. By April of 1973, this movement will reach a level of 7 million tpy. TVA bought the coal rights to this property from the General Services Administration in 1965 for approximately $7 million and is now in possession of reserves containing about 120 million tons of recoverable No. 9 coal, and about the same recoverable amount of No. 11 coal. TVA then contracted through competitive bidding with Peabody Coal Co. to mine the No. 9 seam through two slope shafts. The mines are about 300-ft deep and are separated by the one major fault on this property. The mine portals are approximately 3 ½ mi apart, with the northern portal being over nine miles distant from the Ohio River.

Jan 1, 1971

The BHP Billiton Cannington Mine uses paste as the principal method of backfill. The paste consists of mine tailings and cement. The pastefill process at Cannington includes a surface plant where the thickened total tailings stream is filtered using two vacuum disc filters operating in parallel. The filter cake is mixed with Portland cement in a spiral mixer to produce a paste at a specified yield stress and cement content. The initial system design only required paste to be delivered under gravity. In July 2001, Cannington Mine expanded to 1.8 million tonnes per annum. In order to achieve this, production commenced on five new levels underground, 350 metres horizontally from the paste plant. Due to the high viscosity of paste, this distance was too far to transport by gravity. Traditionally, paste has been transported only short distances (50 m) using positive displacement pumps, with very limited success. At Cannington, a conveyor was installed which was designed to achieve zero spillage into the environment. This paper discusses the innovative design strategies used to attain zero harm on the environment whilst conveying a material, which is difficult to transport.

Jan 1, 2002

By P. W. Erickson

Development of the Twin Buttes mine entailed the largest known preproduction stripping job in the history of mining. It linked earthmovers and conveyor belts in a new approach to development of a pit that may reach, or even exceed, dimensions of 1 x 1-1/2 miles at the surface and go as deep as 1800 feet. The orebody to be stripped was covered by an average of 460 feet of alluvial gravels, which presented an initial stripping job of great magnitude. The initial pit layout and the original time schedule established early in 1965 called for the excavation and disposal of about 250,000,000 tons of alluvial overburden before the end of 1969. Allowing about a year for equipment delivery, this schedule left four years to do the job averaging about 62-1/2 million tons per year. In 1964 when The Anaconda Company undertook the development of Twin Buttes, it was recognized that special planning was necessary for the disposal of waste material and tailings. Environ- mental control was a prime consideration and is particularly sensitive in the Twin Buttes area due to the proximity to residential developments. Disposal of the 250,000,000 tons of alluvium, as well as future rock and tailing waste material, presented a problem which Anaconda engineers resolved by designing a plan to spread out much of the alluvium over an extended area, including a massive 11- 1/2 mile dike system which will impound mill tailing in three basins. The tailing will be impounded behind these-dikes to avoid wind exposure and blowing. The dikes also serve as a

Jan 1, 1974

By John K. Kellis

With the cost competitive nature of material mining, the ability to actively monitor the condition of the conveyor belt systems without personnel dedicated to that task is very desirable. This paper discusses the development of a conveyor belt condition monitoring system, which actively monitors the conveyor belt, without the need to install special antennas. A belt width map can be generated, as well as detection of three types of physical damages: (a) failure of mechanical fasteners, (b) reduction in belting strength due to reductions in competent belt width, and (c) longitudinal belt rips.

Jan 1, 2000

By Owens S. Roberts

The drive selected for any piece of machinery must adequately satisfy the application requirements both during the starting interval and at running conditions, All loading possibilities of the drive must be known and allowances made for any adverse limiting conditions such as extreme cold, or perhaps an intermittent excessive loading situation etc. In general, the drive must be selected to provide the required operating characteristics with maximum reliability and at minimum cost. Simplicity of overall design is always an advantage and care must be exercised to insure that systems incorporating unnecessary complicated parts are not indiscriminantly provided. Important non-technical considerations such as equipment avail-ability (on an overseas project) as well as standardization details also play a role in the drive selection process. Additionally, an assessment of the potential capabilities of the personnel that will have to maintain the equipment can have some influence on the final choice. Several types of prime movers are available but this article will restrict itself to the use of induction motors operating from an available alternating current power source. Many drive arrangements are possible, the most common being the direct coupled single motor arrangement. It is sometimes desirable to use more than one motor per machine, but these designs are usually more

Jan 1, 1971

By Lane White

In conjunction with its 1993 Annual Meeting, held Feb. 15-18 in Reno, NV, SME sponsored a symposium, "Conveyor Belt Engineering for the Coal and Mineral Mining Industries." Eighteen papers were presented, grouped into four sessions: Low Tension Drives, High Tension Drives. Novel Techniques and Specifications. Three of the papers have been republished in this issue of MINING ENGINEERING. Brief summaries of the other 15 papers are presented here. (The 193-page symposium Proceedings, edited by Mike Evans of Consol, includes all of these 18 papers and is available from SME. For the convience of interested readers, an order form is included at the end of this Proceedings summary.)

Jan 1, 1993

By H. Verakis

A fire in a coal mine conveyor belt entry represent a major safety and health risk to miners. Fighting belt entry fires can be a commanding effort. If there is a failure of one aspect in the fire fighting needs such as a dissimilar hose-valve connection, then it can result in the inability to extinguish a fire. Fire incident data compiled over nearly 30 years for underground coal mines shows that fires in belt entries account for 15-20 percent of the total number of fires. Fires in the belt entries of coal mines have resulted in injuries and fatalities. New regulations have been promulgated that require an unplanned fire not extinguished within 10 minutes of discovery to be reported to the Mine Safety and Health Administration (MSHA). A fire that is not extinguished within several minutes may take hours or days to extinguish or may require sealing a section or the mine in some cases. The current fire protection regulations in the U.S. Code of Federal Regulations (CFR), Title 30, Part 75 are designed to prevent or control the fire hazards present in a belt entry. These requirements and other factors affecting belt entry fires are discussed, including fire detection and warning, fire suppression devices, type and location of fire fighting equipment, waterlines, and cleanup and removal of combustible materials. The fire suppression systems used to extinguish/control a belt fire and the effect of ventilation on the propagation of conveyor belt fires are also discussed.

Jan 1, 2009

By R. Todd Swinderman

Impact cradles are installed below the belt in conveyor loading zones to cushion the forces from material loading. In this paper, the author will discuss the need for and then explain the new CEMA standard for engineering of impact cradles. He will review the engineering theory and work through an example to demonstrate the assumptions used in the standard do not inappropriately affect the CEMA rating system.

Jan 1, 2002

By J. R. Thompson

It is common practice, and certainly good business as all of us know, to take care of plant operating equipment. Machinery of any type requires periodic inspection and planned maintenance. With this thought in mind a plant operator should at the end of every shutdown period make regular belt inspections and plan for later appropriate care and maintenance. The points mentioned below are understood well by all of us but are sometimes forgotten because belt conveyors are comparatively easy to operate. Maintenance of any conveyor belt is dependent upon the fundamental characteristics of the two component parts-cover and carcass.

Jan 6, 1950

By Jerome F. Sheldon

The earliest recorded history in the use of belt conveyors in the United States is in O. Evans' "Miller's Guide" published in Philadelphia in 1795. Evans defines a conveyor as a "broad endless strap of thin pliant leather or canvas revolving over two pulleys in a case or trough." (Ref. 1) In this definition, pulleys are being used in a bulk material belt conveyor application. Pulleys used in belt drives can trace their origin back to 1200 A.D. In fact, Engineers had considerable experience designing them into drives transmitting greater horsepower than those used in the early belt conveyors. In belt conveyor application, a pulley's purpose is primarily three-fold, 1) support the belt in directional changes, as designed in the conveyor, 2) transmit driving power to the belt, and 3) guide or train the belt. There are various types of pulleys used in belt conveyor systems and these are thoroughly covered in "Belt Conveyors For Bulk Materials" prepared by CEMA, 1966. For our discussion, however, the most common used in belt conveyors are drive pulleys, snub pulleys, head pulleys, tail pulleys, takeup pulleys and bend pulleys. The drive pulley imparts the driving force to the belt and may be located at the head or discharge end of the conveyor, in return strand, or at the tailor loading end of the conveyor. A snub pulley is located near the drive pulley to provide more arc of contact between the belt and pulley for maximum

Jan 1, 1971

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine's production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

By Edgar T. Gregory

A quiet revolution has taken place in the conveyor belt industry, Man-made materials, improved production facilities, better splicing techniques and emphasis on repair and maintenance have all contributed substantially to lowering material handling costs for the mining industry, It wasn't too many years ago that the rubber industry had only cotton for a belt carcass and tree grown rubber for the protective cover. Then came the development of monofilament rayon. This material had desirable elongation and elastic properties and was the first synthetic fiber to be used in place of cotton. But wet strength and other limitations restricted its use, and the conveyor belt industry turned to nylon. Initially, nylon was considered suitable only for the cross threads or filler threads of a belt carcass. Then technical advancements in heat setting and fabric weave created a major change in belt construction. As a result of these advances the industry was able to take advantage of the full tension strength of nylon cord. Another breakthrough in the use of synthetics was the tremendous increase in adhesion resulting from a chemical bond, rather than the limited physical bond available with cotton. But the advantages of nylon had a more Car-reaching effect, We were able to design a two-ply nylon belt that did the work of a four- or five-ply cotton or rayon belt. A six-ply nylon belt now replaces a twelve-ply cotton elevator belt. Arid nylon resists moisture, acid and mildew, It also has excellent resistance to impact and can be produced with controlled elongation and elastic properties that work to great advantage in reduced-ply belt constructions.

Jan 1, 1971

By P. J. Connors, William J. McCormick, F. B. Olender, Jerome F. Sheldon, Donald T. Mylar, Edgar T. Gregory, Owen S. Roberts, H. Colijn

A quiet revolution has taken place in the conveyor belt industry. Man-made materials, improved production facilities, better splicing techniques and emphasis on repair and maintenance have all contributed substantially to lowering material handling costs for the mining industry. Formerly the rubber industry had only cotton for a belt carcass and tree grown rubber for the protective cover. Monofilament rayon, with desirable elongation and elastic properties, was the first synthetic fiber to be used in place of cotton. But wet strength and other limitations restricted its use, and the conveyor belt industry turned to nylon.

Jan 3, 1972

By J. B. Fletcher

Miami Copper Company has used conveyor belts underground since 1947, At that time, the draw level for a portion of the orebody was only 25 feet above the haulage level To get the main haulage drifts as far away as practical from under the stoping area, 301, belt conveyors were used for lateral transfer, If the haulage drift was kept in good ground., a satisfactory draw of these stopes could be effected in that repairs to the conveyor drifts could be accomplished while drawing ore from the stopes. Some 7,400,000 tons of ore were mined with the 301d belt conveyor at a belt cost of approximately $0,004 per ton of ore. When the mining plan for a new section of the mine was laid. out in 1953, it was decided to use belts to collect the ore from the higher draw levels, and. move the ore laterally to centrally located concrete ore passes for transfer to the main haulage level (See Cut #1), The final plans used belt conveyors too collect from 3 stopes: on the 570 level, 2 stopes on the 720 level, and one stope on the 900 level. The six stopes to be mined in this manner would produce about 8 million tons of ore, and the sequence of mining was such that not more than four 400 feet conveyors would be in use at one time, Four conveyors using 36 inch, 4 ply belting were designed by the mine engineering office and fabricated at the mine shop, so that no piece was longer than 10 feet, and. the heaviest piece was the 25 horsepower motor, The head drive section, and the tail-pulley-takeup section were of bolted construction so they could be broken down for easing moving, Due to the size of the mine openings, the belt had to be transported into the mine in 400 feet rolls, requiring two splices for an installed belt. A torque arm speed reducer was used with a V -belt drive which made it possible to change the speed of the conveyor by changing the diameter of the V-belt pulley (See Cut #2).

Jan 1, 1958

By P A. Collier

The general view of the author is that all the good intentions of manufacturers can fail completely if the variations in circumstances in underground mining are not considered at all times. With a belief that it is the customer that has the experience and know ledge of problems which occur on long installations. Reilloc talk with customers in coal mines around the world, and have done so from their inception. With considerable experience in their home market, their technical approach was received with enthusiasm by coal companies in both Australia and South Africa, and whilst experience was obtained in other countries, it is the particularly close working relationship in these two areas that is covered in this paper. The refinement of manufacturing techniques and the fine tuning of the specification to which the chain is made was developed in conjunction with factual underground experience obtained by customers as they sought to improve their productivity and a reduction in working costs. With a reliable product the mines are able to concentrate on improved operational techniques to extend the useful working life and plan for multi-panel usage of the chain.

Jan 5, 1996

By John F. Bryce, Fazley A. Azhar

With increasing economic pressures to produce more with less, the material handling industry is turning to engineered solutions to reduce the number of people required to operate its facilities, monitor maintenance trends, pin point problems, increase throughput, decrease downtime, identify weak links in the production system, and increase times between scheduled maintenance. One solution to these problems is to implement a Total Control Solution (TCS) using industrial computers, fieldbus networks, and distributive Input/Output (I/O) for control, automation, data acquisition, and analysis. This paper will discuss some of the control fundamental principles used by Technisys, Inc. (TI) to implement TCS.

Jan 1, 1998

By David G. Rasmussen

With low commodity prices and continuing high operating costs, the mining industry must revise planning and operating to take advantage of every tool available. Conveyors operated within open pits are such a tool. Dravo engineers have designed conveyor systems into pits as prime movers in unique situations. Three cases are presented with economic comparisons made to conventional truck haulage. Increasing energy and labor costs tend to make conversion of prime haulage from trucks to conveyors. Long term pit planning and scheduling reduce the effects of conveyor inflexibility.

Jan 1, 1983

By R. T. Swindeman

"INTRODUCTION This paper will discuss the topics in the recently released Conveyor Equipment Manufacturers Association’s (CEMA) Belt Conveyors for Bulk Materials, 7th edition, that deal with safety and maintenance. The most effective way to improve conveyor safety is through designing out hazards in the earliest stages of a project. When the safest way to perform maintenance is also the easiest, mechanics will naturally take the obvious and least hazardous approach. IMPORTANCE OF ACCESS Studies have shown that mechanics spend almost one-third of their time accessing the components to be serviced and approximately 25% of all fatal conveyor accidents occur during maintenance1. Chapter 2 of Belt Conveyors for Bulk Materials deals with design considerations. In Chapter 2 there are recommendations for access at the various sections of a typical conveyor for cleaning, inspection and maintenance. While, in some cases, providing access will increase the cost of the conveyor system there can be significant paybacks in reduced injuries, faster maintenance and easier cleaning. Piping and Conduit One of the significant recommendations in Chapter 2 for access is to restrict the mounting of piping and conduit to the conveyor structure in the Loading and Discharge zones of a conveyor. Piping and conduit are more permanent fixtures than maintainable components and should be located out of the way of components needing frequent maintenance. If electricians and pipe fitters are given convenient locations to make their runs they will natural use them. Flexible conduit and hoses can be used to connect to components from pipe racks and cable trays which further enhances maintenance. Access for Cleaning Another critical aspect of access is for cleaning. Approximately 33% of all fatal conveyor accidents occur while cleaning spillage and carryback under and around conveyors2. In the loading zone having sufficient height under the conveyor for cleaning increases the cleaning interval and allows for safer cleaning. In the discharge zone having adequate access for belt cleaning installation has a direct effect on the ability to install a proper cleaning system and perform maintenance."

Jan 1, 2015