Search Documents

By Törbjorn Naarttijärvi, Bengt Ludvig, Agne Rustan

"Falling rock is one of the major causes of serious injuries and deaths in Swedish mines. The research at the Division of Mining and Underground Construction was therefore directed toward controlled blasting in hard intense jointed rock.The project was started with an extensive literature review. Model tests with a new equivalent model material have been initiated to find ways of improving blasting techniques. The result showed that long cracks arise at the perimeter holes when there is a long time delay between adjacent holes. This led to the theoretical development of a new initiation method with ultra short delays (1,5 ms) f or controlled blasting, called ""Cutblasting"".Full-scale tests have been done at LKAB in Malmberget in hard intense jointed magnetite ore. Four different types of perimeter charges have been tested, namely: tube charges, ANFO mixed with plastic beads, detonating cord and linear shaped charges. Three types of initiation of the perimeter holes have been used, conventional (half-second delay detonators), instantaneous and ultra short ""cutblasting initiation"" (1,5 ms delay). The change in rock strength before and after blasting has been studied with bore hole periscope, vibration measurement and ocular observation of the rock surfaces.Thefull-scale tests showed that ""cutblasting"" with detonating cord in the perimeter holes gave the smallest damage to the surrounding rock. A combination of cutblasting initiation and tube charges are anticipated to give an even better result. A new method of controlled blasting using linear-shaped charges has also been tested, however, this charge type needs further development.The full- scale test also showed that the damage which can be seen on the rock surf ace is about the same for different controlled blasting methods but the not-visual-damage zone varies as much as from 0,1 to 0,7 m.A new classification system for controlled blasting regarding the damage to the surrounding rock has been devised."

Jan 1, 1985

By Sérgio Augusto Ferreira, Alan Gerson Diaz Butron, Carlos E. Arroyo, Marcus Neves, Jorhs Enrique Casimiro Huayhua, Dieggo Santos, Eventomar Junior

The presence of natural underground cavities is normally a characteristic of iron ore deposits, specifically in tropical deposits. Brazil and the United States are the only countries that have a legislation to protect these structures, but in Brazil this legislation is very specific for the existing cavities in the federal territory. These cavities are classified by their level of relevance as high, medium, and low. From this perspective, its preservation becomes mandatory, especially, for those of high relevance in order to protect the species (flora and fauna) that live in them. When these structures are within the production phases, it becomes a challenge to exploit these reserves with the use of commercial explosives, since these structures condition and may restrict the use and amount of explosive charge. This paper presents the methodology of controlled blasting associated with predictability via realistic simulation in production polygons, applied in a Brazilian iron ore mine where there is a presence of high relevance natural cavities with restrictions in relation to the limits of Peak Particle Velocity (PPV), which is product of detonation.

Feb 6, 2023

By Gordon Revey

In construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speed up the work and lessen costs. The process of determining whether or not blasting is practical is ofien complex, particularly when risks are high.

Jan 1, 2001

By Gordon F. Revey

In underground construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speedup the work and lessen costs. The process of determining whether or not blasting is practical is often complex, particularly when risks are high. In this paper, general methods of conducting blasting risk evaluations and outlined and considerations for blast design and risk management are reviewed. This paper also includes three blasting case histories demonstrating how these techniques were used at recent projects. In the first case, a cautious blasting program was developed to facilitate the removal of concrete and rock within a large section of an active mineshaft. The second case involved critical blasting to excavate a dry lake-tap connection between a tunnel and a shaft at the Southern Nevada Water Intake No. 2 project in Henderson, Nevada. The third case history describes how novel blasting methods were used to carefully drop a 2,721,500-kg (6,000,000-lb) concrete caisson into a1.2-m (4-ft) rock socket at the Detroit Outfall No. 2 project in Detroit, MI.

Jan 1, 2001

By C. W. Baxter

Eveleth Taconite Co. was formed in 1963 to mine and beneficiate taconite on the Mesabi Range. Its Thunderbird mine is located mid-way between the cities of Eveleth and Virginia, Minn. The program for blasting restraints here is unique not only on the Mesabi Range but possibly in the world. The ore is a hard siliceous taconite. Its structure varies from bedded to massive with prominent vertical jointing. The jointing of the top or outcrop of the orebody is a challenge for the blasting practices as it is the source of an estimated 75% of the secondary breakage.

Jan 11, 1972

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division's Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine's Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985

By L. L. Gagné

The Churchill Falls Development will eventually be the largest source of hydroelectric power in North America. Churchill Falls was discovered in 1839, but until recent years it was not practical to begin development of this site to tap the 7 million horsepower available. This $1 billion project is located in Labrador, 700 miles northeast of Montreal and 650 miles northwest of St. Johns, Nfld. The construction will divert the Churchill River 5 miles upstream from the 245 foot Churchill Falls. Rapids above and below the Falls, together with the Falls proper, give a natural head of 1,040 feet. In contrast to the basic simplicity of the surface installations, the powerhouse labyrinth is astounding in size and complexity. The largest in the world, it consists of three major chambers - the powerhouse, 972 feet long by 81 feet wide and 154 feet high; the surge chamber, 763 feet long, 40 feet to 64 feet wide and 148 feet high; and the transformer gallery, 856 feet long by 50 feet wide and 39 feet high. Other major features include eleven inclined penstocks, each 1200 feet long and 20 feet in finished diameter; eleven draft tubes averaging 37 feet in finished diameter and 162 feet long; six vertical cable shafts each an average of 865 feet in length; a series of eleven short bus tunnels linking the powerhouse and the transformer gallery; a vertical power-

Jan 1, 1997

By Weiying Zeng, Shouwei Wang, Jinbei Zhong, Xiangdong Meng, Lingtian Meng

"Due to a drainage problem, the Lanzhou to Chongqing high-speed rail line had been out of service during the 2015 wet season, so a drainage tunnel is to be constructed for the line and required to be accomplished before the 2016 wet season. This drainage tunnel is only 5 meters below the line which is in service, therefore blasting vibration needs to be strictly controlled. This paper introduces all theapplied blasting methods, parameters and detonation throughout the entire project, finally bringing in the electronic detonator stagger phase technique and corresponding time difference for detonation."

Jan 1, 2017

By P. R. Day, W. K. Webster

"The introduction of large boreholes underground initially involved taking the techniques of open-pit bench blasting to the production stope, but with deeper boreholes and narrower stopes more controlled techniques must be developed in order to maintain good stope walls and prevent dilution of ore or structural damage to pillars due to blasting overbreak. The points discussed are drilling accuracy and drill pattern, the relationship between open-pit wall control and underground mining, the varied explosives products and initiation devices available, and some of the many ways that variations in loading, such as deck charging, etc., can produce desirable results.IntroductionThe use of large-diameter blastholes for underground mining began ten years ago and today they are widely employed in a variety of orebodies and stope configurations. These big blastholes, which range in size from 4.5 to 8 inches in diameter, were originally employed in the same manner ' as open-pit bench blasts; that is, the stope was silled out to full width and all holes were drilled vertical and parallel. This was suitable for competent, massive orebodies, however the popularity of the big drills saw their usage in more narrow stopes, often with poor ground conditions. The dipping orebodies and small drill sublevels resulted in inclined drilling.Today, there is full-ring drilling of 4.5-inch holes. Some 6.5-inch holes are drilled up to 350 feet deep. A 350-foot borehole may contain 6000 to 7000 pounds of explosive. The detonation of this size of charge weight within the confines of an underground stope can have considerable effect on the stability of stope walls and adjacent pillars. Obviously, precautions must be taken to minimize the damage which would result from the large charge weights possible with these big boreholes."

Jan 1, 1982

By M. S. Raseroka

An experimental rig has been constructed to produce chloride stress corrosion cracks in Type 304L stainless steel tube samples. The samples are to be used to test possible in situ repair methods in future work. The factor which influences the time to failure most strongly is the sample temperature; the distribution of cracks within the sample is affected by local temperature variations and by the position of the water line. Low-frequency oscillations in stress, caused by the on-off temperature controller, did not appear to influence cracking in these tests.

Jan 1, 2009

By G. Vijaya Kumar, B. Srinivasa Rao, G. V. Krishna Rao

The paper outlines the ventilation practices prevailing in coal mines of Singareni Collieries Company (South India). The high annual average surface temperature and relatively steep geothermic gradient results in virgin strata temperatures in the region of 38- 42°C creating environmental problems in the working places. Expensive methods of air cooling can not be employed as the mines are small, and production and productivity do not justify the costs of artificial cooling of mine air. Controlled recirculation of mine air -- the unconventional technique being tried with success in some coal mines in U.K. has been analysed for improving the environmental conditions. The analysis shows that the method is safe, cost effective and can be applied with very little extra equipment.

Jan 1, 1991

By Kwang-Tae Kim, Yong-Kun Choi, Jeong-Soo Chong, Yun-Jae Lee

An annex building at the former Agency for National Security Planning(NSP) complex located in downtown Seoul was demolished by progressive collapse method. This work was done as a part of efforts to restore the landscape of Namsan Mountain which lies in the Center of Seoul. The five-story reinforced concrete structure was razed in 5.5 seconds by the 29kg of high powered explosives which were placed in some 320 holes in the building with floor area of 2,577 m². The asbetos and all the other finishing materials in the building were removed before the demolition and the specially coated wrap minimized the spread of blasting dust. Seismic and air overpressure waves were monitored at 8 points, which were below safety limits and the continuous communication with neighborhood prevented any complaint.

Jan 1, 1998

By Douglas M. Deason

Swelling clays, such as montmorillonite, contribute significantly to the poor dewatering and consolidation behavior of the Florida phosphate clay wastes. Understanding and to a degree, control of the forces which cause the swelling behavior may aid in supplying a solution to this problem. The technical feasibility of utilizing control- led dispersion for aiding dewatering of phosphatic slimes was investigated. This technique is based upon inhibition of swelling and self-dispersing tendencies of the montmorillonite clays by dispersing the solids in electrolyte solutions. Through this process, significant improvements in settling rates and sediment solids content were achieved in both pure clay systems and on simulated phosphate slimes.

Jan 1, 1983

By D. M. Deason, G. Y. Onoda

Phosphate clay wastes, as currently produced, leave montmorillonite clay in a highly dispersed and disintegrated form. Alternative processing, where the extent of swelling and self-disintegration of such clays is controlled or limited, may result in improved settling and consolidation behavior. In this study, a method to control montmorillonite dispersion, through preservation of clay tactoids, was examined. Through this process, significant improvements in settling rates and sediment solids concentrations were achieved in both pure clay systems and on simulated phosphate clay wastes.

Jan 1, 1985

By Edward Fitch

The DOE is evaluating Yucca Mountain, Nevada as a potential site for disposal of high level nuclear waste. Yucca Mountain is located approximately 160 km northwest of Las Vegas on the western edge of the Nevada Test Site and the Nellis Air Force Range. An exploratory tunnel has been constructed through Yucca Mountain for site characterization. A controlled drilling and blasting technique, smooth wall blasting, was used to excavate the TBM starter tunnel and alcoves off the main tunnel to provide areas for scientific investigation. Fundamental to the blasting program has been the use of two blast design equations used in concert to minimize blast damage to the surrounding rock mass. The first of these equations was developed by Roger Holmberg and estimates near-field peak particle velocity that is the basis for minimizing blast damage to the host rock. The second of these equations was developed by B. H. Sanden and provides bore hole pressure estimation which allows controls to minimize crushing of the rock mass along the perimeter yet allowing enough force to create tensile failure between perimeter bore holes. This is key to the smooth wall blasting technique. To date, essentially the same controlled drilling and blasting program has been in place for all excavation requiring controlled drilling and blasting at the ESF. The controlled drilling and blasting program uses an iterative process to achieve continuous improvement in the blast rounds. This involves interaction between Architect and Engineer (A/E), Constructor, and Testing Coordination O&e (TCO) to ensure each blast round successfully meets the expectations of affected participants. The A/E requested that the TCO provide validation of the near-field peak particle velocity estimation under the Construction Monitoring Program. Data gathered under this program were reduced by statistical analysis and used to verify blast design parameters and provide a site specific blast damage relationship.

Jan 1, 2000

By Scott L. Burrill

In the past 100 years in the mining industry, many references are made to the "Widow Makers", 'Miners Con" and many other derogatory names related to physical hazards. They reflect the lack of understanding of the problem facing the early day miner. Workers were enticed, in some cases, to take a chance against a medical question mark that could not be explained by the doctors of those early days. The optimism of the mining man and the challenge of work led him to believe that the physical results could not apply to himself and only applied to some of his fellow workers. Much of the time, to his dismay, he found that he had lost to the game of chance. As medical knowledge improved and mining management began to understand the effects of conditions in the mines and beneficiation plants, steps were taken to alleviate or eliminate the health hazards that were present, The organizations engaged in mining that did not take an active interest in employee health found themselves to eventually be placed in the position of being forced to take action by Federal and State legislation. We find ourselves in the 1970's on the threshold of a new era where the general public is concerned vociferously about "their" environment and the industry feels the governmental controls more strongly than ever before. It can be said that in the past 100 years we have advanced from the "Widow Makers" of the 1870's to the "Retirement Makers" of today. The difficulties of the early days in underground mining were of times compounded in the beneficiation plants above ground. As late as the 1950's some crushing and milling installations in the United States were operating under environmental conditions that complied to the then existing legislation but were below the health level sought by conscientious management. The Mission Concentrator Crushing Plant was designed in 1959 and placed in operation in July, 1961. In the past ten years the crushing plant has been continuously complimented by technical people, government inspectors and casual

Jan 1, 1971

By Ken Fiorentino, Gordon F. Revey

H3 Tunnelers recently excavated two conventional 48 foot diameter highway tunnels through the Halawa side of the Tran-Koolau Mountains on Oahu. The primary blast design challenge on this Job was minimizing overbreak In the alternating layers of pahoehoe and aa lava, clinker, end tuff. Two different excavation techniques were evaluated in the Halawa tunnels. The first method used drilling and blasting to excavate the tunnels to within one foot of their final perimeter. A roadheader, mounted on a backhoe, was then used to excavate the remaining foot of ground. The second method used conventional smoothwall blasting techniques, without any mechanical excavation. This paper describes the details and relative success of the two excavation methods tried in the Halawa tunnels.

Jan 1, 1993

By Ulrich Leiste

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By N Elith

The explosives demolition of a post-stressed, steel reinforced, concrete road bridge in Australia’s capital city, Canberra. The bridge was 50 m from the new replacement bridge, 320 m from community structures and within five kilometres of the national parliament buildings. The job required multiple overlays of risk assessment, public relations, safe work procedures, specialised blast design, environmental predictions and flyrock controls. Project stakeholders included Worksafe, Roads ACT, bridge owners, consulting structural engineers, community groups and road users. The bridge precincts, including a major road underneath, had to remain operational to peak traffic in the days leading up to the demolition. The break-up and removal of debris had to be executed in just two days from Friday to have the road beneath re-opened for Monday morning city-bound traffic.In Canberra, all explosives demolitions are now viewed with particular caution after a demolition in 1997, during which a young girl was killed. Any approval requires that Explosives Regulations, AS2187 2006 and Worksafe processes are satisfied, and a convincing case presented for blasting as a safe and viable option.Our design used specialised shaped cutting and blasting charges to sever in situ concrete beams and tendons and to shatter components of the stressed concrete bridge assembly. We include comments on structural engineering reports dealing with pre-weakening mechanisms. The benefit of pre-weakening is that it reduces the amount of explosives needed to safely complete the job and facilitates quick removal of debris after the shot. The complementary skills of the team, each one an expert in his field, resulted in a highly successful demolition, praised by authorities as an outstanding example of controlled use of explosives.

Nov 8, 2011

The processes by which particles and bubbles interact capture many of the central concepts of colloid science and hydrodynamics. This area of research embraces hydrodynamics, interfacial(including capillary) forces, particle and bubble behaviour and solution chemistry. In this review, we discuss collision, attachment and stability efficiencies. We deal with the identification of a flotation ?domain?, the deformation of a bubble surface upon interaction with a solid surface, the kinetics of three phase contact line expansion and the determination of attachment efficiencies through to the direct measurement of bubble-particle interaction forces. We have recently carried out a test of collision theory where the latter embraces both inertial and centrifugal forces. The real challenge is now to quantitatively describe the behaviour of real systems and to incorporate a reliable description of the behaviour of particles in flotation froths. The approach described is very robust when applied to flotation, both from qualitative and quantitative points of view, providing an intellectual foundation for understanding this complex process in separation science and technology.

Jan 1, 1999