Search Documents

By R. V. Ramani, W. Miola, R. Srikanth, S. C. Soboleski

"Dust control in high-production longwalls requires attention to operating practices and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in US longwalls. Yet, under certain conditions, 31% of the shearer operator's dust exposure can be due to support movement.Several methods have been developed for the control of shield-generated dust. But the need for better methods is apparent. In this paper, the amount of airborne, respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. Ten experiments were conducted on five longwall faces in four mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne, respirable dust concentration immediately downwind of the shield move varied between 0.12 and 1.75 mg/m3 in the five longwall faces. The mass of airborne, respirable dust gener-ated by shield movement was found to vary between 39 and 386 mg per shield move. The results from this study reveal that control of dust from longwall shields requires a combi-nation of approaches involving alternative operating prac-tices, reducing shield dust generation rate, increasing face air flow and decreasing personnel exposure.IntroductionIn 1992, longwall mining accounted for about 36% of US underground coal production, a 240% increase from a decade ago. The absolute longwall tonnages were 46 and 133 Mt (51 and 146 million st), respectively. Compared with room-and¬pillar mining systems, the longwall mining system is charac¬terized by higher recovery, enhanced safety and higher pro¬ductivity.However, personnel dust exposure on a longwall face is higher than in other types of mining. According to Mine Safety and Health Administration (MSHA) data, fewer longwalls were in continuous compliance with the applicable dust standard in 1992 than in 1989.Controlling shearer-generated dust and reduction of per-sonnel exposure to airborne dust have commanded attention in the design of longwall faces, operational practices and ventilation schemes. Studies in the United States and abroad have revealed that support-generated dust can be a major obstacle to compliance under certain conditions (Becker et al., 1989; Bradley et al., 1983; Jankowski and Organiscak, 1983; Jankowski et al., 1990; Organiscak et al., 1985)."

Dec 1, 1996

By T. T. Chen, J. L. Jambor, J. E. Dutrizac

A reconnaissance study of the neutralization potential of 30 diverse minerals, 28 of which are silicates and aluminosilicates, has shown that most of these minerals contribute minimally to the neutralization potential (NP) in standard static tests. Feldspars in particular give low NP values and would not be expected to attenuate the acidity to any significant extent in acid rock drainage settings. The BET-determined surface areas of the minerals vary considerably, and the large surface areas of some of the pulverized samples have clearly affected the NP values even though the standard static-test protocol was used for the preparation of the samples. The low NP values of most silicates and aluminosilicates are in general agreement with the laboratory-determined slow dissolution rates for these minerals. The results suggest that, in the prediction of whether rocks will be acid-producing, the most realistic measure is that of the carbonate content. In mine wastes from metalliferous ore deposits, the contribution to the NP by the non-carbonate gangue assemblage is unlikely to be more than a token amount until well after the establishment of an acid rock drainage situation.

Jan 1, 2000

By G. Kritikakis

Rehabilitation of sites contaminated by oil products and chlorinated organic compounds is a costly task which affects the planning of urban and infrastructure development. An integrated approach based on the non-invasive geophysical technology is utilized for subsurface characterization of contaminated land. In this approach the localized information, provided by chemical analysis of soil samples collected from bore-holes, is used for the calibration of the geophysical data. This information is subsequently extrapolated to the area under investigation by combining it with the geophysical results, providing thus information about pollution accumulation, contaminants? flow and pollution sources. Two case studies are presented from sites contaminated by heavy metals (Venice, Italy) and oil products (Athens, Greece). Resistivity, electromagnetic and seismic methods were used in this approach. Namely, electrical tomography, electromagnetic mapping, ground penetrating radar (GPR), multichannel analysis of surface waves (MASW) and seismic refraction experiments were conducted. In Italy, the sections from the multichannel analysis of surface waves imaged successfully a buried channel where the pollution is concentrated. Preliminary results are also discussed from the geophysical survey in Greece where the thickness of the oil phase located on top of the water layer is 60 cm.

Jan 1, 2006

By Paul Stothart

Context ? Industry is active in urban, rural, and remote regions ? Faces a range of environmental challenges and ?social license? issues ? There are also Aboriginal and northern issues ? Also very active internationally, with associated challenges ? Environmental/social groups often target the industry ? The important contribution of the industry should not be overlooked Useful Minerals and Metals Minerals are intrinsic to the residential, municipal, communications, and transportation infrastructure of modern life. Examples: Hybrid motors - nickel hydride batteries Water purification systems ? nickel, rare earth elements Catalytic converters - cerium Screens and monitors - several rare earth elements Clean electricity - uranium Circuitry - gold, copper, aluminium, lithium, titanium, silver, cobalt, zinc Instruments - copper, silver, nickel, cobalt, copper, brass Protective products ? zinc, calcium carbonate, sulphur

May 1, 2008

By Ricardo Chavex, Adrien Letellier

Flyrock remains one of the most critical issues in open-pit blasting. Despite the significant improvements made with modern surveying methods, the necessity remains to define sensible danger zones around blasting areas. Therefore, many semi-empirical models predict flyrock distances based on trajectory calculations and probabilistic adjustments. However, most are merely based on nominal parameters, even though a considerable amount of precise data is nowadays available thanks to modern measurement techniques using lasers, GPS, drones, and probes. These data provide accurate information about the actual field circumstances of a blast concerning geometry and rock-mass conditions. So how can we use and integrate them into existing flyrock models? The answer to this question can significantly improve the accuracy of flyrock prediction models and enhance safety. This paper will present a method to adapt existing models to actual field data using appropriate software and digital tools during the blast design process. In addition to calculating a more pertinent danger zone perimeter, this method provides an efficient and practical tool that helps prevent flyrock incidents. Indeed, it allows the blast designer and shot firer to be warned if there is a hazardous critical deviation due to local conditions. Moreover, it also enables blasters to communicate better and share the visualization of the blast-specific evacuation zone. The paper will also discuss how this method can be calibrated and how it has been used to analyze some actual flyrock incidents.

Jan 21, 2025

By K Kongolo, M K. Kalenga

It is well known that the electrochemical precipitation of metals from aqueous solutions is conducted by the electrochemical standard potential scale. This scale indicates the order of nobility of different metals. Consequently, the standard potential scale shows the nocivity of metals when they are present as impurities in aqueous solutions containing metals. In the hydrometallurgy of cobalt, nickel and zinc are co-deposited during cobalt electrodeposition. Nickel has almost the same chemical, physical and electrochemical properties as cobalt. Furthermore, the electrochemical potential of nickel is relatively higher than that of cobalt. For this reason nickel is preferentially reduced at the cathode in the presence of cobalt. The presence of small amounts of zinc in solution leads to contamination of cobalt electro won. In spite of its lower electrochemical potential in comparison to cobalt, zinc is reduced on the cathode because of its higher hydrogen-overvoltage. But, in the hydrometallurgy of zinc, small amounts of cobalt present into solution will contaminates the zinc reduced at the cathode. This is easily explained by the fact that cobalt is more electropositive than zinc. The co-deposition mechanism of sulphur at the cathode is not yet well understood. Great attention has to be paid to the mechanism of co-deposition of sulphur during cobalt electrolysis..This work aimed to investigate the influence of some parameters on the co-deposition of nickel, zinc and sulphur during cobalt electrowinning. The following parameters have been investigated : Co2+ concentration in the electrolyte, current density and ammonium sulphate (NH4)2SO4 additions. It has been established that important nickel, zinc and sulphur co-deposition takes place at relatively low Co2+ concentration in solution. The behaviour of these elements with regard to the cathodic phenomena has been established.

Jan 1, 2005

By R. S. Young

There can be very few members of the Institute who failed to appreciate this extremely interesting and informative paper by Mr Rohrmann of Highveld Steel and Vanadium Corporation. This story of vanadium in South Africa has a very wide appeal to members of our profession: it embraces both ferrous and non-ferrous metallurgy, and both hydrometallurgy and pyrometallurgy. In a comparatively short time, South Africa has become one of the the world's leading producers of vanadium.

Jan 1, 1985

By René Winand

The paper gives a synthesis of research work performed in the department during the last ten years and dealing with cobalt , copper and manganese electrodeposition in chloride aqueous solutions. Special emphasis is given to electrocrystallization. For copper, properties of the electrolyte such as solubility limits, electrical conductivity and complex ions stability are discussed in connection with leaching, purification of the electrolyte, and metal recovery. When possible, kinetic parameters and probable electrode mechanisms are given. Problems that are still to be solved are also listed.

Jan 1, 1985

By D. Savile Davis

D. Savile Davis* (Member): The members of the Chamber of Mines Research Laboratories, headed by Dr Cook, indeed deserve all the plaudits that have been given for the original conception of the rock-cutter, and for the research work that has gone into designing the equipment now being tested. Underground trials with the rock-cutting machines at the Doornfontein Gold Mining Company Limited have been encouraging to the extent that 29 square fathoms of rock have been cut in the past three months with two modified prototype machines. Both the hangingwalI condition of the stope and the control of stoping width have been excellent. So far, however, the rate of production has been too slow and does not compare with conventional stoping methods, due firstly to the time-consuming operation of moving the machine forward and resetting it in its next cutting section and secondly to mechanical defects. Although great strides have been made in improving the tungsten carbide cutting tool, further progress is dependent upon engineering development in the design of a more reliable and versatile machine within economic limits. Commenting briefly on the experiments that have been carried out on the Gold Fields mines, the rock-cutter, when used at the Luipaards Vlei mine, some 600 ft below surface, cut very nearly perfect slots above and below the reef on a stope face but was unable to cut slots in the reef itself. At the Doornfontein mine, however, where the tests are currently being carried out at a depth of 8,000 ft below surface and where there is a much greater pressure acting on the rock face, vertical fracture planes can be clearly seen in the hangingwall running parallel to the face. Owing to the presence of these fracture planes it has been found impossible to cut slots of any depth and the action of the machine is more one of spalling than of cutting, resulting in slabs of combined reef and waste falling from the face as the cutting tool advances. This is accentuated by the existence of a well-defined hangingwall parting plane. Most of the slabbing takes place from the slot cut below the reef to the hangingwalI of the stope. Since waste sorting in narrow conditions and poor lighting is not an efficient operation, the reef together with a proportion of waste rock, has to be removed from the stope. The ripping action of the machine as opposed to slot cutting under these particular conditions may not be a great disadvantage, as the volume of waste which can be packed depends on the ratio of reef width to stope width and with a narrow reef body some waste has to be removed to the surface. In these circumstances mining at depth with this type of machine should not be viewed as selective mining but more correctly mining without explosives. Another type of rock-cutter is being tested by the Gold Fields Group, consisting of a diamond studded rotating disc, which has, to date, cut slots 10 ft in length and averaging 7 1/2 in. in depth. It is, however, too early to comment on the practicability and economics of such a cutter. The great interest that is at present being shown in breaking rock without the use of explosives warrants comment on the Robins raise-borer, recently introduced into South Africa, and used for the first time with great success at the Doornfontein mine.

"Quang Ninh province is located in the north east of Vietnam and the coal mining in the province generates two thirds of the province’s GDP. The coal is extracted from both open pit and underground mines for the country’s complete coal export and by a share of more than 90% for domestic coal usage. Overburden generated through open pit mines is piled up nearby in the form of large waste rock dumps. The side-hill fill dumping near open pit mines is the source of environmental degradation in the region. Among the current problems at solid waste rock dump sites are dust emissions during and after dumping as well as Acid Rock Drainage (ARD). One of the major existing problems at waste rock dumps is dump stability (comprising erosion, sliding and subsidence issues). The RAME R&D project (Research Association Mining and Environment in Vietnam) is - among other activities - actively involved in the research for stabilisation and rehabilitation of mine waste rock dumps in Vietnam in the form of several sub-projects. The Institute of Mining Engineering I of RWTH Aachen University is leading the sub-project of mine waste dump stabilisation in co-operation with Chair of Geotechnical Engineering and Brenk Systemplanung GmbH. Mine waste dumping in the form of layers as an alternative to the side-hill fill dumping is expected to bring up environmental and economical benefits by minimising the problems of dump sites with the contribution to a sustainable development. Reduction of the post construction settlements, long term stable dump profile with minimum erosion, improvement of material parameters for geotechnical slope stability through compaction from hauling trucks as well as economical evaluation of new dumping concepts are the areas of the current research. The project has been financed by German Federal Ministry for Research and Education (BMBF). The ultimate aim of the sub-project is the compilation of the project results in the form of a "Best Practice Guide" and software based "Decision Support System" for planning and management of solid mine waste dumps."

Jan 1, 2011

By H. G. M. Rose

Contribution to the above paper by H. G. M. Rose* (Fellow) INTRODUCTION Dr Lawrence is to be congratulated on his most interesting and instructive paper, particularly on his suggestion for a model to increase mining productivity through improved management performance. In view of an experiment initiated in one Union Corporation mine (Mine A) and later extended to a second mine (Mine B), it might be of interest to review the many human factors involved and the initial productivity results achieved.

Jan 7, 1974

By R. T. Muller

Contribution to the above paper by R. T. Muller (Visitor) Demands are being made and pressure is being brought to bear on employers in South Africa to narrow or eliminate the wage gap between their White and Black employees. Few thinking people will dispute the fact that a constant improvement in the wages of Black personnel is essential, but this cannot be done merely by a redistribution of income in South Africa.

Jan 7, 1974

By Jean Frenay

Bacterial leaching tests have been carried out on Portugese pyritic ores containing zinc, copper, lead and silver as valuable elements. Both indigenous and isolated strains of Thiobacillus ferrooxidans were used. During the tests the factors pH, Eh and dissolved oxygen were measured and related to the leaching activity of the bacteria. Different means to estimate or determine the real bacteria concentration were examined. The influence of nutrient media and particle size has been evaluated. The role of galvanic couples was studied by electrical linking of mineralogical samples of pyrite, sphalerite and chalcopyrite. Leach residues were examined by optical microscopy to follow the mineralogical alterations during the leaching. The results show a rather good leaching of the sphalerite. However, the dissolution of copper from chalcopyrite is much more difficult, 50 % recovery never being obtained.

Jan 1, 1985

By C. Zografidis, K. Karalis, E. Devlin, S. Tabouris

"The main parameters affecting energy and electrode consumption in smelting reduction of Greek nickeliferous laterites in submerged arc electric furnaces (E/F) were investigated. Within this framework, the operational data of E/Fs, such as energy consumption indicators, electrode consumption indicators and chemical characteristics of Fe-Ni and slag, were correlated with the physicochemical characteristics of the calcine, produced by roasting reduction of laterite in rotary kilns (R/Ks), such as reduction degree, temperature, chemical composition and granulometry. The results obtained provide a significant input for further research on the modelling of the roasting reduction – smelting reduction process, which is a critical tool for energy optimization.IntroductionThe two main steps of pyrometallurgical treatment of greek nickeliferous laterites for ferronickel production include: i) drying, pre-heating and controlled pre–reduction of laterite ores with solid fuel reducing agents and fuel oil in rotary kilns (R/Ks) for the production of a calcine, and ii) smelting reduction of the calcine in open-bath submerged-arc electric furnaces (E/Fs) for the production of Fe-Ni alloy with 12-16% Ni [1].The energy absorbed from the endothermic reductive reactions of iron, nickel and cobalt oxides (Fe2O3, FeO, NiO and CoO) of the calcine with the remaining carbon in the E/Fs, corresponds to about 16% of the total energy output in the smelting reduction step [1]. This is indicative of the significance of the calcine’s reduction degree for the electric energy requirements in the E/Fs. Moreover, the chemical characteristics and the granulometry of the calcine constitute critical parameters for the energy requirements as well as the smooth operation of the E/Fs."

Jan 1, 2012

By Natasa Mitevska, Predrag Djordjevic, Zivan Zivkovic

This paper presents the results of an experimental investigation into the distribution of copper in the slag of an industrial reverberatory furnace sulfide concentrates smelting process in the copper smelter RTB Bor (Serbia). The influence of copper content in the matte, the temperature and the height of the slag on the content of copper in the slag was determined as Cuoxide, Cusulfide and Cutotal and was based on possible mechanisms for the loss of copper in a silicate slag from the smelting of sulfide copper concentrates. The greatest quantity of copper in the silicate slag was found in the form of matte particles, which were captured in the slag as a result of the “flotation” of SO2 gas which was formed by magnetite reduction with FeS at the slag–matte interphase boundary.

By Natasa Mitevska, Predrag Djordjevic, Zivan Zivkovic

This paper presents the results of an experimental investigation into the distribution of copper in the slag of an industrial reverberatory furnace sulfide concentrates smelting process in the copper smelter RTB Bor (Serbia). The influence of copper content in the matte, the temperature and the height of the slag on the content of copper in the slag was determined as Cuoxide, Cusulfide and Cutotal and was based on possible mechanisms for the loss of copper in a silicate slag from the smelting of sulfide copper concentrates. The greatest quantity of copper in the silicate slag was found in the form of matte particles, which were captured in the slag as a result of the “flotation” of SO2 gas which was formed by magnetite reduction with FeS at the slag–matte interphase boundary.

Previous investigations of stress conditions under which core discing occurs have concentrated on shear stress as the cause of this phenomenon. In this paper it is suggested that discing initiates as a result of extension strain, which develops in the field of triaxially compressive stress ahead of the borehole end.

Jan 1, 1982

By G. E. Karantzavelos

Although jigging has been the subject of extensive studies, evaluation of the effect of various jigging factors on the efficiency of separation has been less comprehensive. The basic factors that affect jigging separation are reviewed, a mathematical model describing jigging kinetics is presented, and attention is focussed on the mechanisms of the stratification process. The parameters of the kinetic model (the Wei- bull distribution function) are redefined in a gravity concentration technological sense, and their values are estimated for a wide range of jigging conditions. Several mathematical relationships (regression models) are also formulated which express the dependence of total time required for the complete stratifaction of mineral particles on the operating jigging variables.

Jan 1, 1984

By G. L. C. Young

The first full-scale Reichert cone concentrating plant to be erected at a large South African gold mine was at President Steyn Gold Mining Company, Welkom. ThiR plant was installed as a part of the runof-mine mill extension of 150000 t per month that was commissioned in 1976-1977.

Jan 1, 1982

By Elias Rigopoulos

In the present study the reductive behavior of dust from the rotary kilns (RK), in ferronickel production from nickeliferous Greek laterites, is investigated. The study concerns dust of various origins (washing towers, electrostatic filters, polycyclones) and pellets made from the dust. Reducibility was studied in the temperature range of 700 °C to 850 °C in a laboratory tube furnace. Experimental results showed that reduction degree increases with temperature up to about 800 °C. The rate of reduction is great during the first minutes, giving a reduction degree R% equal to about 25%, in only a few minutes. After this, the rate is decreasing until it diminishes to zero after about 10-20 minutes of reaction. Maximum reduction degree achieved is 26 to 28%. Rates and reduction degrees at various temperatures are higher for the dust samples than those of the respective pellet samples. Keywords: Ferronickel, metallurgy, laterites, pellets, reduction

Jan 1, 2004