Search Documents

By E. Almendras de Siegel

Pyrometallurgical processes have the thermodynamic capability of treating complex and dirty ores and concentrates to produce high purity metals and inert slags. Modem pyrometallurgical processes are environmentally sound and competitive with other processes. However, there is still a need for sensors and other practical tools that permit a rapid evaluation of the performance of these processes. In order to contribute to satisfying this fundamental requirement, the authors developed the IDENT.LA software that permits the automatic mineralogical analyses of inorganic materials, including the final and intermediate products of pyrometallurgical processes. The technique allows determining the grain size distribution of mineralized inclusions, the surface relations between metallic phases, and conducting modal analyses of the essential phases that are present in the samples. Three basic automatic operations are performed: creating a representative image of the sample; identifying the metallic and non-metallic phases; and measuring the features of the resulting image. The results are used to evaluate the performance of pyrometallurgical and other processes. In this paper, the authors discuss the application of the technique to a sample of slag from a slag cleaning process that uses a carbonaceous reductant. In this case, process performance impacts not only on the efficient reduction of the slag magnetite and on copper recovery but also on the quality of the process off-gas. The mineralogical analysis of the slag is a valuable tool in assessing process performance and in recommending changes of operating conditions.

Jan 1, 1999

By L. -C. Lai

A series of LaNi5-based alloys, with partial substitution of Ni by Al, Co, or V, were prepared The gas-phase hydrogen absorption kinetics and pressure-composition-temperature curves were measured The activation became easier and the plateau pressure was reduced as Ni was partially substituted by Al Substitution with Co reduced the hysteresis as well as the hydrogenation capacity, but enhanced the absorption kinetics Vanadium is often considered as a hydride former, but when it was added to LaNi5, it was found that V occupied the B site. A small amount of substitution of Ni with V led to a higher hydrogenation capacity and faster activation rate Based on these properties, an alloys LaNia 25CO0.5V0.1Al0. 15 was fabricated as an electrode. Compared with LaNi4.85Al0.15, it was found to exhibit faster activation, higher discharge capacity, and longer cycle life. The variation of the hydrogenation characteristics is discussed based on the physical and chemical properties of the alloying elements.

Jan 1, 1997

By James A. Sommers

Combustion of niobium nitride powder in a stream of oxygen results in several niobium oxide phases, depending upon reaction parameters. Under rapid oxygen flow, the oxidation produces a molten mass which coalesces into droplets of ca. 2 mm dimension and effectively quenches to leave NbO2 and other lower oxides of niobium, despite the ambient atmosphere of oxygen. A preliminary survey of reaction parameters which govern the split between reduced and oxidized products is presented. This technique offers novel synthesis means for binary oxides when mixtures of NbN and other materials are combusted together, since the niobium moiety is generated in a molten state.

Jan 1, 1995

By Guohua Bai, Lin Zhang, Shan He, Xuling Chen, Min Gan, Xiaohui Fan, Yanbin Tang

"For reducing the dust content in flue gas during copper smelting in the Ausmelt, technologies and mechanism of strengthening the pelletizing of copper concentrate were studied. The results show that adding bentonite, organic binder or composite binder can effectively enhance the strength of green pellet and reduce the rate of shedding powder in drying process, and composite binder works best. When adding 1 % of composite binder, the drop strength of green pellet increased from 1.9 times/P to 4.5 times/P, the rate of damage dropping from 2 m reduced from 50.12% to 13.08% and the rate of shedding powder reduced from 60.28% to 25.13% at drying temperature of 400111. In addition, the mechanism of binder absorbed in the surface of mineral was investigated by infrared spectroscopy. The results showed that composite binder absorbed in the surface of copper concentrate was in the form of chemisorptions, which made hydrophilic enhanced, while bentonite absorbed in the surface of copper concentrate was physisorption.IntroductionWith the technologies of copper smelting developing, the equipment of copper smelting steps into a large-scale and efficient level in recent years. As Ausmelt smelting is characterized by being efficient, environmentally-friendly and energy-saving, it is generally recognized by the enterprises of copper smelting [l]. The process of Ausmelt smelting starts with materials mixing, and then pelletizing. From this point onwards, pelletized balls are charged to the top of the furnace, undergoing drying and smelting reaction[2]. Since copper concentrate is fine-grained, directly adding into smelting furnace can make it blown out of the furnace together with the airflow upwards, rendering flue gas high in flue dust, which can cause the loss of concentrate greatly, and make smelting environment poor as well. The concentrate transported into the furnace and smelted after disc balling is conducive to improve the capacity of melting furnace during copper concentrate smelting, reduce the powder shedding rate and improve enterprise benefits."

Jan 1, 2013

By T. K. Mukcherjee

The importance of the processing of secondary resources such as solid industrial wastes and liquid effluents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure.towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention' can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids; plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction play a pivotal role. This paper outlines the efforts made to use solvent extraction to recover(1) base metals. such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge(2) refractory metals like molybdenum and vanadium from sulphidic byproducts and spent catalyst and (3:) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, "which influences the metal recovery process significantly, has drawn a special emphasis. hi the case of refractory metals, basic extractants .like Alamine 336 has been pressed into service to produce kilogramme. quantities of pure salts of molybdenum and vanadium, Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using 'a solvent system comosed of DEHPA and TOPO.

Jan 1, 1996

By Kohei Yajima

The dusts and fly ash generated from the steelmaking processes and municipal solid waste incineration processes contain metallic elements such as Fe, Zn, Pb and Cd with considerable amount of halogens. In Japan, zinc in dusts is recovered by Waelz kiln or MF process, etc. However, the presence of halogen in the dust affects the evaporation and condensation behavior of zinc and other metals, and disturbs the direct recycling of dust to steelmaking processes, because alkali or heavy metals reacted with halogen vaporize easily as halides and/or oxyhalide compounds in pyrometallurgical process. Recently, the formation mechanism of zinc oxychloride vapor was investigated and the formation of zinc oxychloride such as ZnOCl was proposed. However, considering the practical operation, the effect of water vapor on the evaporation behavior of oxychloride is not fully clarified yet. This study is focused on the investigation of evaporation behavior of ZnO with Ar- O2-HCl-H2O atmosphere.

Jan 1, 2008

By Alva L. Kuestermeyer

This paper presents the results of an economic analysis in the production opportunities of various co-product and minor metals in the base metals smelting 'industry. Pro forma cash flow statements were prepared for each co-product and/or minor metal analyzed utilizing US tax laws for items such as depreciation and taxes. The generated cash flows are based on anticipated revenues, estimated capital and operating costs (where applicable), and nominal production data for the respective co-products and minor metals. The economic analysis includes consideration of items such as metal payfors and bonus metals ,payments per current smelting terms. Sensitivity analysis to market prices is also ,addressed.

Jan 1, 1995

By E. Morrice

Solubility of yttrium oxide (Y203) in fluoride melts was experimentally measured in the temperature range of 998 to 1273 K and, YF3 composition in LiF.YF3 melts varying from 20 to 50 mole pct using a graphite crucible in an argon atmosphere. Solubility of oxide in the melt was found to increase with increasing temperature and YF3 composition in the melt. An expression for in XY2O3 as a function of temperature for several melts was deduced. The calculated activity coefficients of Y2O3 in the melts exhibited a negative deviation from Raoult's law.

Jan 1, 1989

By A. Bilodeau

A new hydrometallurgical process for the production of refined gold and the recovery of palladium and platinum from silver anode slimes has recently been developed and installed at the, CCR Division of Noranda Inc. The process, which facilitates the production of gold of >99.99% purity in the face of increasing palladium receipts comprises; leaching silver anode slimes with hydrochloric acid and hydrogen peroxide at 95°C to solubilize gold, palladium, platinum and base metals while simultaneously rejecting silver as insoluble silver chloride; precipitating gold from the leach solu¬tion with sulphur dioxide gas in two stages to produce a first-stage high purity gold product and a second stage impure gold which is recycled to the leach; washing, melting and casting of the pure gold; precipitation of a palladium-platinum concentrate from the gold-free solution by reduction with sodium formate at pH 4 and 95°C; and neutralization of the palladium precipitation effluent to pH 10 with lime. The results of laboratory and pilot plant studies leading to the adop¬tion of this process are discussed, and data are presented for each of the unit operations. Details of the engineering of the commercial plant are given, and plant start-up experience is described.

Jan 1, 1987

By Mingchun Lu, Yunjin Yan

"This paper describes a new type of bell-less top installed on two relined blast furnaces at Tianjin Iron Works and another new-built at Echeng Steel Works in China. A compact installation was presented for existing furnace top innovation with the least reformation of existing top structure. A water cooling and sealing gearbox used for driving the chute discards completely the traditional idea about necessity of continuous supply of cooling gas for the gearbox. A multiring spreader and its dozens of selectable charging patterns enables an operator to achieve optimal burden distribution easily under the condition of a minimum investment of control equipment. Some useful conclusions have been made through a small-size model and a full-scale model tests. The excellent characteristics and the superiority of the new top have been fully proved at both works.IntroductionIt is known that there are some advantages with the bell-less top of a blast furnace: suitable for furnace to operate at high top pressure, capable of realizing optimal burden distribution, less investment and maintenance costs, etc. But why do most of blast furnaces in the world still remain using conventional bell top. One of the concerns is that current bell-less tops still have some shortcomings:1) The height of a current bell-less top might be lower than three or four-bell top or two-bell plus valve seal top, but still much higher than an ordinary two-bell top.2) The gearbox for driving the rotating chute is positioned onto the lip of the furnace. It is subject to attack by crude hot bf gas. Continuously pumping cooling gas (pressurized nitrogen or clean bf gas) into the gearbox is indispensable to withstand such a harsh working environment. Therefore, a plant furnished with blower8 and its ancillaries has to be built, It involves a large sum of investment and much expense in its annual running costs.3) Although the current bell-less charging device as a means of controlling burden distribution possesses a wide range of freedom, it is difficult to realize optimal burden distribution. There are some large blast furnaces realized better burden distribution, but sophisticated control means is indispensable so that the investment of control means is much higher."

Jan 1, 2000

A study was undertaken to remove the Se from waste solutions using a raw form of the biomass called Iota Chips derived from the seaweed, Eucheuma spinosum. Removal of Se from solutions was investigated as a function of time, pH, conc. of Se in solution (0.1 to 100 ppm) and lota Chips to liquid ratios of 10-2 to 10-5. For solutions containing initial conc. of 0.1 ppm Se, with the addition of Iota Chips at a solid to liquid ratio of 10-3, the Se conc. decreased to 0.03 ppm in about 3 hours. Iota Chips absorption capacity to the Se and its application to the treatment of the metallurgical processing effluents are discussed.

Jan 1, 1992

By Tatsuo Itou

Both sales volume of Aluminum Can and its recycling rate are remarkably increasing here in Japan. In 1993, recycled can volume was 11.78 billion cans ( 116,258 metric tons ) and its recycling rate 57.8 percent. We, MITSUBISHI MATERIALS CORPORATION. the leading manufacturer of aluminum can in Japan and our affiliated companies are very deeply involved in recycling used beverage cans ( U.B.C ) and recycling them back to can stock. In this paper. I would like to present the following; 1. Recent trend of beverage can consumption in Japan. 2. Trend of aluminum can and its recycling rate in Japan. 3. Future of aluminum can business in Japan.

Jan 1, 1995

By Matthias Frommer, Carl-Peter Reipl, Reinhard Flende

"Today there is a growing demand for strip of superior steels with specifically tailored technological properties. Especially strips of high-strength, micro-alloyed steel grades applied to manufacture longitudinally and spiral-welded pipes are a growth market. Tubes are generally required to have high strength and sufficient toughness values and thus favour specific hot strip microstructures. The correlation of chemical analysis, process parameters and mechanical properties with microstructural features is still a challenging task. During the last decades, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) have become useful tools for the characterization of complex microstructures. The EBSD data provides an immense variety of post-processing possibilities, e.g. related to grains, grain boundaries, misorientations or texture. This paper highlights the results of an advanced analysis of microstructures representing industrial produced hot-rolled strips and presents an approach to define and quantify some essential microstructural parameters.IntroductionHigh-strength microalloyed steels have been used for the production of welded pipes for more than 30 years. However, the alloy design of pipeline grades is being continuously modified and the process technology optimized because of the increasing high strength-toughness combination requirement for pipeline steels. Compact strip production (CSP®) technology is an upcoming promising route for the production of high-quality pipeline steel grades [1]."

Jan 1, 2012

The viscosity of high magnesium content FeO-Fe3O4-SiO2-CaO-MgO slags at nickel flash smelting conditions was investigated using a commercial rotational viscometer. The studied parameters were compositions of slag and temperature. The viscosity of these slags was measured as a function of CaO, MgO, SiO2, FeO. Fe3O4 and Fe/SiO2 in temperature range from 1473K to 1723K. These slags contained 5.81 to 10.59 pct MgO, 0 to 10.37 pct CaO, 28.21 to 36.21 pct SiO2, 39.40 to 55.42 pct Fe and 1.1 to 1.5 Fe/SiO2.

Jan 1, 1999

By B. Thompson

"1. AbstractMagnesium alloys have been successfully recycled for decades and have won acceptance for use by die casters and most of the automotive industry. As the supply chain for magnesium and magnesium alloys continues to change, due to the consolidation of producers, it is essential that quality control methods be closely examined with each new supplier added. An examination of the various process steps that are needed to assure quality in the final product will be discussed thus giving a basis for the auditing of new magnesium suppliers.2. IntroductionMagnesium recycling in the past has been somewhat limited due to its use more as an alloying agent for aluminum based alloys and as a desulfurization agent in iron and steel than in more readily recycled structural products. Recycling efforts continue to improve as more production is finding its way into automotive structural components, hand tools, and a variety of computer and cellular telephone applications.With the closure of several large North American primary magnesium production facilities over the past decade we have only recently witnessed a tightness in supply that is driving magnesium prices significantly higher, nearly doubling the price in the last year alone. The rapid escalation in pricing will provide additional economic incentives to fully utilize recycling for the recovery of an even greater percentage of both old and new sources of magnesium scrap. Political pressure continues to intensify towards the secondary recovery of any and all recoverable resources of which magnesium recycling readily applies.Economics will also likely drive the development of new sources of magnesium production, both from primary and secondary production. As new sources of magnesium are offered to the marketplace the potential for product quality issues may increase. When considering any new raw material supplier a decision must be made as to the impact of defective material on the intermediate or finished product. Quality defects in magnesium ingot can result in a variety of appearance, corrosion, and even adverse structural effects in the finished product. The potential severity of the impact of defective raw materials on the finished product will determine and often justify a close look at any new supplier. An on-site audit of a new supplier of a critical raw material is often justified to ensure that an adequate quality assurance system is in place. We will now look at a number of key production points that should be examined during an on-site audit that have can have an impact on the overall quality of the finished product."

Jan 1, 2008

By R. E. Johnson

The No. 3 reverberatory furnace at Phelps Dodge. Corporation's Morenci, Arizona copper smelter first received oxygen from a new oxygen plant during October 1982 and began operation with oxygen-fuel and oxygen sprinkle smelting burners which burn concentrate with oxygen. The furnace was completely converted to roof-mounted oxygen-fuel firing in October 1982. All conventional air-fuel bridge wall burners were extinguished at that time. The novel arch-mounted oxygen sprinkle smelting system began continuous operation April 1983. Since startup, unit fuel requirements decreased and furnace throughput significantly increased. Furnace off gas SO2 strength increased from an average of 1.5% SO2 to an average of 20% using only oxy-fuel burners. Oxygen sprinkle burner operation also has given excellent results, with the furnace off gas strength increasing to 35%-60% S02. There has been a reduction in overall arch temperatures, an increase in matte and slag temperatures, and a lowering of furnace bottom buildup with oxygen smelting. Furnace off gas is blended with converter off gas and treated in a sulfuric acid plant.

Jan 1, 1983

By Luiz A. Teixeira

This paper reports the results of kinetic studies involving the precipitation of arsenic from aqueous solutions as FeAs041 Fe(OH)3' using FeS04 as source of Fe ions, and Air or H202 as oxidizing agents. Both systems lead to an efficient removal of arsenic. The differences in oxidants performances are in the precipitation reaction rate -much faster using hydrogen peroxide. Mechanisms of reactions were suggested based on the following main steps:

Jan 1, 1996

By James C. Barker

Recent investigations of a 55-km long trend of intrusive complexes on southern Prince of Wales Island have identified significant resources of Nb, Y, REE. U, Zr, and a host of potential by-product metals. The northwesterly trend comprises multi-phased sodic alkaline and peralkaline diorite, monzonite, syenite, and riebeckite granite. There are at least three significant deposit types recognized, two of which, 1) pegmatite dikes/vein-dikes that zone laterally from the intrusions and 2) concentrically zoned pegmatites, contain most of the lithophile metals. A third, epigenetic replacement-type mineralization, contains much of the U resource. Other deposit types with minor or unknown resource potential include diatremes, carbonatite, and placers. This report summarizes the deposit evaluations, characterizes the mineralization, and estimates the resources. To date a total of 40.7 million tons of mineralized material is estimated as indicated or inferred. Most of the Y203 plus REO is at a grade exceeding 0.5% and half of the Nb20S exceeds 0.125%. Tonnage estimates would likely be substantially lncreased with additional exploration. Mineralogy is generally fine-grained and complex, and consists of more than a dozen principal REE-Y-Nb-U-Th-Zr phases, the sum of which may compose up to half of the rock. Approximately half of the REE-Y content comprises the heavy yttrium subgroup which is uncommon compared to deposits elsewhere. Although the Alaskan deposits are likely subeconomic at today's metal prices and consumption levels. recent technological advances suggest future demand may increase.

Jan 1, 1988

By H. Matsuda, T. Iwashita, H. Awata, H. Liwei, D. Hirabayashi, Y. Saito, S. Ozawa, Y. Goto

"The present study is concerned with investigating the effect of chemical treatment on enhancing the HCl absorption capacities of coal burnt ash and slag. It was found that the HCl absorption capacity of coal burnt ash discharged from fluidized bed combustor was improved by hydration with water and 5% polyethylene glycol solution. This phenomenon was based on an increase of the specific surface area of treated coal burnt ash. The HCl absorption capacity of hydrated ash with polyethylene glycol solution was almost equivalent to that of standard CaO and Ca(OH)2. In particular, the specific surface area of hydrated ash with polyethylene glycol solution was found to be 19 m2/g, which was more than over eight times larger than that of raw sample. Hydrated slag treated with lON sodium hydroxide solution also showed high HCl absorption capacity, with highly improved surface area. It was found that the absorption capacity of slag for HCl depended on the treatment time, showing the maximum absorption capacity for 12 hours of hydration treatment.IntroductionA large amount of coal burnt ash, slag and dust are discharged from such industrial processes as coal combustion and metal refinery etc., and it becomes an serious problem to recover and diminish these solid wastes because of the shortage of dump sites and subsequent metal elution to the environment. Figure 1 shows the present situation of reutilization of coal burnt ash and slag in Japan [1,2]. It is shown in this figure that these solid wastes are recycled as materials in the fields of earthwork, agriculture and forestry etc. A part of these solid wastes, however, is still dumped to landfill. To decrease this dumped amount, the development of environmentally friendly reutilization technique for these solid wastes is of great importance."

Jan 1, 2000

By H. Y. Cheng

A pulse column solvent extraction system was evaluated as an alternative to mixer-settlers for the separation and purification of rare earths. The column tested had an inside diameter of 44.5 mm and had 36 sieve plates with a free area of 25%. Pulsing was provided pneumatically using a solenoid valve controlled by a timer so that both pulse amplitude and frequency could be varied. Feed to the column was a mixed rare earth chloride solution containing 10 g RE L-1. The extractant was 5% Ionquest® 801 in Shellsol 2037 diluent. Hydraulic performance of the pulse column was excellent with no propensity towards stable emulsions or crud formation under normal operating conditions. The column was operated in organic-continuous mode with flow rates chosen so that yttrium and the heavy rare earths were extracted with high efficiency while the light rare earths were rejected. Yttrium extraction varied from 83 to 99.2%. Concentration profiles were measured in both the aqueous and organic phases, and, from this data, the height of a transfer unit (HTU), the mass transfer coefficient (Kxa) and the continuous-phase axial dispersion coefficient (Ey) were computed. The HTU ranged from 17-92 an which is within the range of values reported for other (non rare earth) pulse column systems.

Jan 1, 1992