Search Documents

By Jeffrey Shepherd, Scott R. Smith, Eduard Guerra

"Electrochemical and spectroscopic evidence for the dissolution of a Au electrode by meso-2,3- dimercaptosuccinic acid (DMSA) from an acidic LiCl04 electrolyte is presented. Near the potential of zero charge, DMSA was determined to form a stable layer on the metal surface but at more anodic polarizations, DMSA was displaced from the metal through an oxidative process. The anodic displacement of the layer from the electrode resulted in a small amount of Au that was detected in the electrolyte using atomic absorption analysis. The extent of Au dissolution, was monitored while holding the potential of the electrode for 24 hours at the thermodynamic Eo/H,O in LiCl04 electrolytes containing 10 mM DMSA. This routine resulted in detectable quantities of a soluble Au-DMSA complex in the electrolyte and the greatest leaching was observed at a pH = 2.0. At room temperature, the leaching rate was stable at 10.9 µg cm·2 hr·' however, upon increasing the temperature to 50.0°C, the rate of Au dissolution increased yielding an average rate of extraction of 40.1 µg cm·2 hr- 1. Interestingly, after the first 12 hours of leaching at 50.0°C, the leaching current decreased dramatically suggesting surface passivation which prevented further Au extraction. The implications of this process in the industrial leaching of Au will be discussed.IntroductionThe use of cyanide in the industrial process of leaching Au from ores has raised concerns regarding both operational safety and environmental issues surrounding the disposal of spent leaching eftluents in tailings ponds. Depending on the chemical nature of the processed ore, the spent solutions that are released into the tailings ponds can contain toxic cyanide, either dissolved or complexed with different metals and may pose serious risk to wildlife as well as freshwater contamination to nearby water systems. Because of these issues, some recent studies have focused on the exploration of more environmentally-friendly molecules to selectively leach Au with appropriate kinetics. However, to effectively leach Au into an aqueous solution, a suitable ligand that reacts to form a stable chemical bond with Au is needed to form soluble Au complexes that can be later recovered [I]. Recently several sulfur bearing alternatives have been shown to leach significant quantities of Au in aqueous solutions. These include thiourea [2], thiocyanate [3], and thiosulphate [4]. However, alkylthiols are also known to quickly form a stable covalent Au-S bond [5], but have been relatively understudied in term of their ability to leach Au in solution, even though some short chain thiols are water soluble and relatively nontoxic."

Jan 1, 2012

By Wang Shuchan, Zhang Zimu, Zhang Dianhua, Liu Yan, Zhang Ting-an, Zhao Qiuyue, Lv Chao

Rare earth extraction tank has many adverse effects like big floor space and high production accumulation during industrial production. Current researches usually focus on changing the device structure without making a breakthrough towards gravity clarification. This paper attempts to achieve this goal by using both the action of clarification by gravity and clarification by stirring. Because many physical parameters affect the clarification and separation rates, the density, viscosity and surface tension of the two phases were determined at different temperatures and different concentration of aqueous solution. The innovation of this research involves adopting the Karl-Fischer method to investigate water content in oil phase during the stirred separation process. In this paper, the separation effect of different physical parameters was studied and the dimensional equation between water content and the physical parameters was established by combining with the experimental data.

Jan 1, 2014

By Ludy C. Motta, Denise C. O. Nascimento, Sergio N. Monteiro

"Natural cellulose-based fibers are nowadays of growing interest for modern industrial composites. Relatively unknown fibers like piassava, curaua and gourde have shown promising behavior as reinforcement of polymeric composites. However, the hydrophilic characteristics of the natural fibers impair its adhesion to the normally hydrophobic polymeric matrix. Surface treatments can, in principle, improve this adhesion and the fiber/matrix interfacial strength. In this paper, the effect of alkali treatment of the surface of piassava (Atallea funifera) waste fibers was investigated in terms of the change in strength of epoxy composites reinforced with these waste fibers.IntroductionThe consequences of global warming and the increase in the price of petroleum are motivating the use of natural materials as substitute for energy intensive synthetic materials [1]. In particular, natural fibers obtained both, from cultivated plants such as jute, sisal, hemp and flax as well as from industrial waste such as sugar come bagasse and coir, are being considered to replace synthetic glass fibers [2,3]. These natural fibers, also known as lignocellulosic fibers, present the comparative advantages of being renewable, recyclable and biodegradable. Moreover, lignocellulosic fibers require less amount of processing energy and are neutral with respect to CO2 emission, which causes the atmospheric greenhouse effect responsible for the global warming [4]. Low cost is another important economical advantage of the natural fibers over the synthetic ones and the application of lignocellulosic is also associated with a lower wear of processing equipment and better finishing of molded components [5]. Moreover, for some fibers, properties such as the mechanical strength and impact resistance can be superiors to the corresponding properties of synthetic glass fiber [6]. The characteristics and properties of several lignocellulosic fibers are, nowadays being extensively discussed in the literature. It is beyond the scope of this work to comment on the hundreds of papers dealing with this subject. However, there are still less known fibers with great potential as engineering material that deserves investigation."

Jan 1, 2008

By H. Fukushima, T. Ohgai, N. Baba

The electrodeposition behavior of Zn and the morphology of the deposited Zn were studied in electrowinning solutions containing polymer additives such as gelatin and polyethylene glycol (PEG). The cathode potential was shifted in a less noble direction and the polarization resistance for Zn deposition increased with increasing concentrations and molecular weights of both gelatin and PEG added to the electrolytic solutions. However, when the molecular weights of these additives exceeded about lxlO4, the cathode was depolarized and the polarization resistance for Zn deposition decreased with increasing molecular weight. The crystal grain size and the (002) orientation of the deposited Zn became smaller when the concentration and molecular weight of the additives increased, and the cathode was polarized.

Jan 1, 2000

By Yang Hong-ying, Yu Juan

Electrochemical behavior of natural chalcopyrite in electrolyte solution at pH value of 6.97 was studied by cyclic voltammetry, X-ray photoelectron spectroscopy and electrochemical impedance spectroscopy. The results showed that the electrochemical processes occurred on electrode surface were controlled mainly by the growth of sulfur species at lower applied potentials (<0.35Vvs.SHE), and the oxidative dissolution of sulfur species and the hydroxylation of iron at higher applied potential (>0.45V). The EIS spectra of oxide product layers could be illustrated by the equivalent circuit of Re(QdlRct(QfRf)), and the degree of hydrophilicity for chalcopyrite was higher when the value of charge transfer resistance Rct. was greater. The optimum potential range for the floatation of chalcopyrite in collectorless solution at pH value of 6.97 was between OCP (0.165V) and 0.35V.`

Jan 1, 2015

By Sheng-li Wu, Guo-liang Zhang, Bo Su

One of the major challenges for the Canadian Gen IV Super-Critical Water-cooled Reactor (SCWR) concept is the selection of fuel cladding materials. The Canadian SCWR concept will operate at a core outlet temperature of 625 oC and 25 MPa of pressure with peak cladding temperature reaching as high as 800 oC. Corrosion resistance is an important factor for material selection. Austenitic stainless steels that contain Cr contents greater than 18 wt.% are generally considered to provide adequate corrosion resistance. In this work, the pressure dependence of the corrosion of austenitic stainless steel 310 containing 24 wt% Cr is assessed at 625 C for exposures of 1000 hours to evaluate the suitability of superheated steam as a surrogate for supercritical water at 25 MPa. Transmission Electron Microscopy (TEM) revealed that 310 exposed to different pressure conditions at 625 oC. (i.e., 0.1, 8 and 29 MPa) had generally the same type of the oxide structure, i.e., a Cr-rich oxide with the spinel structure on outer surface adjacent to the water phase. The material exposed at 8 and 29 MPa had a double layer oxide structure, with the outer oxide layer having a much larger grain size, while the samples exposed at 0.1 MPa showed only a single spinel-phase oxide layer. Cr-depleted recrystallized austenite grains were found underneath the spinel phase oxide. The adjacent large-grained austenite substrate had M23C6 carbides in the grain interior. The implications of these results are discussed.

Jan 1, 2015

By Shantanu Chakrabarti, Khursid Alam Khan

"Globally, the use of metallic coated steel sheets in the automobile industry is increasing. The sheet should have excellent formability, weldability, paintability and corrosion resistance. Since bare cold rolled steel sheets have certain limitations, application of galvanized steel sheets is steadily expending. Galvannealed steel sheet fulfills all requirements and has become of major interest in the automobile industry.The success of Galvannealed (GA) steels in the body-in-white depends upon material design and parameters of various processes involved, like cold rolling, continuous annealing, hot dipping and galvannealing. In the present work, powdering resistance, one of the important product characteristics of GA, has been studied and a relation is established between the process parameters and the powdering value. The product obtained through optimization of the process parameters have been successfully used by major automotive producers without any powdering problem, for internal as well as external automotive applications.IntroductionThe present automotive industry demands that steel for the auto components should have excellent formability, weldability, paintability, corrosion resistance etc. In addition to this there is specific requirement for some particular components like high surface quality for skin panels. Corrosion resistance of panels is important requirment which determines the life of the particular component and brand value of the automotive. Among all the zinc based steel coating used in the automotive industry coating produced by Galvannealing process has received most attention because of its excellent weldability along with superior corrosion resistance and better paintability."

Jan 1, 2012

By Hani Henein

"Heat transfer between droplets/particles and a gas phase plays an important role in the transport of numerous materials processing operations. These include rapid solidification operations such as gas atomization and spray forming, as well as chemical systems such flash furnaces. Chemical reaction rates and solidification are dependent on the rate of gas-particle or gasdroplet heat transport. Using a heat transport model validated using single fluid atomization of molten droplets; the effect of process variables on heat losses from droplets was examined. In this work, the effect of type of gas, droplet size, gas temperature, gas-droplet relative velocity on the heat transport from AA606 l droplets was examined. The most critical of these process variables to heat transfer is identified and will be presented.IntroductionIn materials processing, droplets are often encountered and used in processing a wide range of liquids and slurries. The small size of the droplet enables high reaction rates or high solidification rates in many systems. In order to capitalize on these high rates of transport processes, sprays are· also developed to maximize throughput. The design of these sprays, however, does not account for the transport steps and rate limiting mechanisms at the droplet surface. Rather, spray design focuses on maximizing the break-up of a stream or slurry into small size droplets or controlling the spread of the spray. Spray systems in industrial use typically generate droplets of wide size distribution leading to a wide range of reaction times for each of the droplets. Often the generation of a spray involves a number of coupled phenomena such as stream break-up, droplet-gas transport, droplet size distribution and spray geometry. Using gas generated sprays, it is not possible to identify how individual process variables contribute and control each of these coupled phenomena. While many mathematical models have been developed of sprays and they attempt to simulate coupled droplet transport, they do not provide insight into the contributions of different mechanisms in heat transfer. This is primarily because the basic fundamental heat transport between droplet and gas cannot be isolated from other gas spray phenomena experimentally such as two-way thermal coupling [l]. Thus, experimental validation of heart transfer of large and complex industrial spray models is not carried out. Hence, the validity of spray models remains in question and the approach required to optimize spray processes cannot be clearly identified"

Jan 1, 2004

By Toshihide Takenaka

Improvement of corrosion resistance of Mg metal by addition of rare earth metal (RE) was studied, and the effect of surface oxide layer with RE was investigated. The corrosion resistance of Mg was remarkably improved by adding a small amount of RE, and the suitable RE content was clarified. The corrosion resistance of Mg was particularly bettered by conversion coating using a solution including both RE(NO3)3 and Mg(NO3)2. This result indicates that the surface oxide layer consisting of both Mg and RE gives good corrosion resistance to Mg metal. In this study, direct electrodeposition of Mg metal containing RE was also tried in molten chloride with RE chloride, and it was shown that electrolysis could be performed stably. The RE content in the deposited Mg metal was depended on the concentration of RE chloride in the bath and the cathode potential, and Mg metal containing the suitable RE content for its corrosion protection was obtained easily by direct electrolysis.

Jan 1, 2006

By C. O. Bounds

The performance of AB5-type alloys for hydrogen absorption including the electrochemical absorption as an electrode for rechargeable batteries has been demonstrated&apos; to be a complex function of the composition, microstructure and surface condition. The compositional studies have focused primarily on substitutions for Ni on the B-site (e.g. Co, Al, Mn, etc.). This current study examines the effect of rare earth substitutions for La on the A-site and considers both other "light" rare earths (Ce, Nd, Pr) and "heavy" rare earths (Dy, Sm, etc.).

Jan 1, 1997

By De-qing Zhu, Zi-fu Gao, Jian Pan

"In order to produce high quality metalized products and prevent from burden cohesion during pre-reduction, self-fluxed pellets were made for COREX process in the paper. The effects of reduction temperature and reducing gas composition on pre-reduction behaviors of self-fluxed pellets are studied. The results show that the prereduced pellets have poor quality and deposited carbon appears when the reduction temperature is between 600°C and 700°C. The metallization rate, reduction degree and compressive strength of prereduced pellets are promoted by the elevating reduction temperature and mole fraction of H2. Pellets reduced by pure H2 at 800°C have high metallization rate (96.2%), reduction degree (99.4%) and compressive strength (960N/pellet). In all tests, self-fluxed pellets display normal swelling (RSI<l5%) behavior which reveals that self-fluxed pellets are suitable for COREX process. Increasing reduction temperature and mole fraction ofH2 in reducing gas is benefit for pre-reduction of pellets.IntroductionCompared with Blast Furnace, the COREX process has advantages of short flow sheet, using non-coke coal and high-energy utilization. Acidic pellets and lump ores are the chief iron- bearing burden for COREX process which could lead to low melting point substance appearing in per-reduction process. In addition, the acidic hematite pellets tend to swell during the reduction [1-3]. This will result in decreasing compressive strength of pellets, burden cohesion, bad air permeability and poor work status in shaft furnace. Adding carbonate flux could restrain burden bonding to some extent in actual production, but decomposition of carbonate flux increases energy consumption. Worse still, weak reduction potential is unfavorable to iron material reduction [ 4, 5]."

Jan 1, 2013

By Zhiyun Li

Room temperature infrared reflection spectra of 2 n-type homo-epitaxial epifilms have been measured in the work. The effect of the refractive index on the determination of layer thickness using traditional calculation measurement is studied and some improvements have been added to the measurement to improve the accuracy and stability of the measured results. Results of the improved method have great agreement with the results from SEM and both variance and mean relative error decrease an order of magnitude.

Jan 1, 2010

By Murat Baydogan

Effect of retrogression and reaging treatment on hardness and stress corrosion cracking resistance of 7075 aluminum alloy was investigated. As received 7075 alloys in T6 temper condition were retrogressed at 170, 220, 240 and 380°C for different durations between 15 s and 60 min. Subsequent reaging was made at the T6 aging condition. Treated materials exhibited higher hardness and better stress corrosion cracking resistance than T6 temper in a wide range of retrogression temperature and time. The highest hardness was obtained after retrogression at 170°C for 210 s followed by reaging, corresponding to 20% hardness improvement. Improvement in stress corrosion cracking resistance of the alloy by as much as 85% was also observed. In this paper, improvements in hardness and stress corrosion cracking resistance are discussed on the basis of the microstructural changes during retrogression and reaging treatment.

Jan 1, 2006

By Mingming Zhang, Marshall S. Coe, Marcelo W. Andrade

To supply iron units and flux burden in blast furnaces, sinter basicity is one of the vital parameters for sinter plants. The sinter basicity also plays an important role in sinter quality since it imparts the formation of different mineral phases in sinter. Pot-grate sintering tests were carried out with low and high basicity to investigate the effects of sinter basicity on sinter mineralogy, properties and productivity. It was found that with an increase in sinter basicity, both sinter productivity and reducibility (RI) increased. Tumbler index (TI) and low temperature degradation index (LTD) of high basicity sinter were comparable to low basicity sinter. Softening and melting tests showed that sinter with 3.5 C/S basicity had slightly higher softening temperature comparing to lower basicity sinter with C/S 2.6, acid and fluxed pellets. XRD analyses confirmed the formation of silico-ferrite of calcium and alumina (SFCA) and calcium ferrite (CF) in the tested sinter samples.

Jan 1, 2015

By Min Chen, Cui-huan Huang, Zhen Tian, Jian-hong Dong

"The present work studied the production of Fe-Si-Mn alloy from adjusted converter slag by thermodynamic analysis. The results showed that solubility of SiO2 in the molten slag increased with increment of temperature, and it is about 80% at 1800 ?. With increment of SiO2 content, a(MnO) and a(CaO) decreased, and a(FeO) increased to the maximum when w(SiO2) is about 30%. As a result, the reduction of the slag was in the order of Fe?Mn?P before SiO2 reduction, the reduction order was Fe?P?Mn?Si when SiO2 content in the slag was from 46.4% to 54.2%, and changed to Fe?Si?P?Mn when SiO2 content exceeded 54.2%. The mass fraction of Si in the alloy phase increases with increasing of w(SiO2) in the slag, and the mass fraction of Si in the alloy reached to 62.2% at 1800 ?.IntroductionFerroalloy production is a high energy consumption and high pollution industry[1-2]. If ferroalloy production could be produced from molten slag by addition of carbon-reducing agent, the valuable metal and oxide in the slag can be recycled, most importantly, if the high-temperature resource carried by molten slag can be made full use in the field of ferroalloy production, the power consumption of ferroalloy production could be cut down greatly.Converter steel slag is a kind of byproduct in steelmaking processing increasing rapidly with the increment of crude steel, but the utilization ratio is low. Most heat recovery research is still in the experimental stage except the heat recovery of blast furnace slag by water quenching method, at present[3-4]. It is of great significance for enterprises to energy saving and emission reduction if the molten steel slag could be utilized directly. Not only the reuse methods of liquid steel slag material can be promoted, but also the use of heat carried in the slag could be achieved. The basicity of converter slag is high and the activity of SiO2 is low so the reduction of SiO2 in the slag is little. The compositions of slag and metal phases were calculated by Factsage program on different conditions to explore the reduction of converter slag for recovery of valuable metals and an efficient new way to use the high-temperature heat combining with the current reuse and research status of converter slag. Further, the improvement of components activity in slag and the increase of Si concentration in the metal were also dicussed."

Jan 1, 2012

By S. G. Kumar

Experimental studies on high carbon steelmaking through LD Converter - Vacuum Arc Degassing - Bottom Pouring route to produce low oxygen steels were carried out. The results indicated that it is possible to produce steel with a total oxygen content of less than 15 ppm. Thermodynamic and mass balance calculations are made on low-carbon steels that are treated by a complex deoxidation practice based on primary deoxidation of aluminum, manganese and silicon additions; followed by secondary deoxidation of vacuum degassing with simultaneous additions of aluminum. The results showed that primary deoxidation is mainly due to aluminum and the effect of carbon under reduced pressures on deoxidation of molten steel that is already killed by aluminum is negligible. The effect of process parameters on total oxygen content of steel, like carbon content, slag composition and inert gas purging, are discussed.

Jan 1, 1994

By T. Innmi

The potential of the nickel matte anode was measured during the matte electrolysis in the commercial cell. The slime layer consists of elemental sulfur and was found to greatly influence the potential of anode. The measurements of porosity and permeability of the slime suggest that the voltage drop of the slime layer dominates the potential. Furthermore, the diffusion of the electrolyte through the slime layer is also one of the factors to determine the potential. In addition, the copper content of the nickel matte anode was found to affect the change in the anode potential during the electrolysis. The role of copper on the anodic dissolution of nickel matte is discussed in this work.

Jan 1, 1988

By R. G. Reddy

The effect of solid particles on viscosity behavior of Na2O-O-B2O3-SiO2 melts of composition XSio2/XNa2o =0.5 and in the temperature range of 900- 1150 K was studied. Samples were analyzed by X-ray diffraction and optical microscopy. The results showed that a crystalline phase (NaBO2) was formed and its amount increases with decrease in X,, from 0.50 to 0.25. The experimental viscosity values were compared with the predicted values using our viscosity model developed earlier. At low temperatures, for low content of B2O3 , the experimental values exhibits a large deviation from the predicted values. It was concluded that the deviation was due to the formation of solid particles in the molten slags. The existence of these solid particles increased the viscosity values significantly. A new viscosity model was developed to include the effect of solid particles.

Jan 1, 1993

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu

Jan 1, 2015

By Shize Jin

Effect of four polyols, namely ethylene glycol (EGL), glycerol (GCL), propanediol (PDL), butanediol (BDL) and three organic acids, namely oxalic acid (OA), malonic acid (MA) and succinic acid (SA) on the current efficiency (CE) and the cell voltage during zinc electrowinning was studied. Galvanostatic polarization was conducted in a supporting electrolyte (SE) containing 180 g dm-³ H2SO4, 60 g dm-³ Zn2+ and 8 g dm-³ Mn2+ at 38°C with magnetic stirring. The imposed current density was 50 mA cm-². The anodes were made of a Pb-Ag alloy and the cathodes were made of an aluminum alloy. The results showed that all the polyols tested in this study decreased the current efficiency and the cell voltage, but the decrease of the cell voltage was not important. Oxalic and succinic acids decreased the current efficiency to a less extent than the polyols, but did not decrease the cell voltage much. The only compound that increased the current efficiency was malonic acid, and its capacity of decreasing the cell voltage was the highest within the seven tested organic compounds.

Jan 1, 2003