Search Documents

By Kevin Jinrong Ma

Underground mines often experience roof falls in entries, crosscuts, and intersections of active mining sections, main travel ways, and belt entries. Roof fall heights greater than 20 ft (6 m) make re-bolting of the newly exposed roof dangerous and impractical. To protect mine personnel, belts, moving vehicles, and other facilities, mine operators typically install steel structures such as square or arch sets in the roof fall areas. Wood lagging is usually installed between the steel-sets to enclose the area and protect the entry from recurring falls. Usually the void space above the steel-sets and laggings is backfilled. However, backfilling high roof fall voids is costly, which causes some operators to leave the voids open. In this case, durability of wood over time and the capability of the steel-set and wood lagging to resist falling rocks are unknown. During the last few years, Keystone Mining Services, LLC (Jennmar Corporation affiliate engineering company) designed, tested, and developed an impact-resistant lagging system to protect steel-sets1. Various steel-sets protected with the impact-resistant lagging were approved by MSHA and installed in different underground roof fall rehabilitation projects. This paper presents (1) design, development, and laboratory testing of the patent-pending impact-resistant lagging panel, (2) steel-set design methodology according to the American Institute of Steel Construction (AISC) national standard, and (3) impact-resistant steel-set design method based on Law of Conservation of Energy. Two underground cases are reviewed to demonstrate the successful application of the impact-resistant lagging system.

Jan 1, 2011

By A. M. Richardson

The significance of a massive sandstone unit in the immediate roof to longwall support weighting is well known. If the unit lies in the main roof above the zone of caving, its influence becomes more difficult to calculate using traditional methods. Much of the reserves at Cyprus Plateau's new, multi-seam Willow Creek Mine are located in the A Seam. The massive Kenilworth Sandstone is typically situated 21.3 m (70 ft) above the A Seam in the main roof and is on average 14.6-m (48-ft) thick, ranging to 29.0-m (95-ft) thick. This paper describes the application of distinct-element modeling to determination of the appropriate yield capacity for supports at Willow Creek. The modeling was determined to be useful for understanding support loading mechanisms and as an aid to engineering judgment in selecting supports.

Jan 1, 1996

By G. C. Sun

Rock mechanics properties, i.e. uniaxial and triaxial compressive strength, indirect tensile strength shear strength, Young's modulus, and poisson's ratio were collected for coal and related strata from 50 coal seams in 90 mines. The methodology of data organization and retrieval is described in details. The values and .ranges of those properties are also discussed.

Jan 1, 1993

By Essie Esterhuizen, Michael M. Murphy, Chris Mark

"The response of the surrounding rock mass to the creation of mining excavations determines the ultimate load on a pillar support system. In conditions where the ground is relatively soft and weak, the full overburden weight can be transferred to the pillar system. However, in stiffer and stronger rocks, a greater portion of the overburden load is transferred to the unmined coal barriers or abutments, and the pillar stress is reduced. This paper makes use of numerical models to examine the interaction between typical pillar systems and the surrounding rock mass for weak and strong geological conditions at various spans and depths of cover. The concepts of structural failure and functional failure of pillars are used to assess pillar performance when pillars are deformed beyond their peak resistance. The results show that the span-to-depth ratio is an important factor in determining the pillar stress and the ultimate deformation of pillars. The ultimate pillar strain appears to be closely related to the functional success of pillar systems.INTRODUCTIONThe National Institute for Occupational Safety and Health (NIOSH) was requested by Congress to study the safety of retreat pillar mining following the Crandall Canyon Mine disaster that took place near Price, Utah in August, 2007. As a part of this study, an investigation was made to better understand how the rock mass responds to the creation of mining excavations and how the loads are distributed among the pillars and the surrounding abutments or barriers. The outcome of these investigations contributed to the development of a modified loading model for the ARMPS-2010 (Mark, 2010) method ofretreat mining pillar design.Structural and Functional Failure of PillarsPillar design is typically conducted by estimating the pillar strength and stress, and then sizing the pillars so that an adequate margin of safety exists between the expected strength and stress. The pillar strength can be defined as the maximum resistance of a pillar to axial compression (Brady and Brown, 1985). If a pillar is loaded beyond its peak strength, load shedding or yielding can occur, and the pillar is considered to have failed as a structure. Structural failure generally refers to a loss of loadcarrying capacity."

Jan 1, 2010

By David A. Newman

Barrier pillars created during mine development provide additional reserves during mine closure and can be the sole access to reserves previously abandoned because of mining height or out of seam dilution limitations. The safe and successful mining of barrier pillars requires a thorough knowledge of the magnitude and distribution of the vertical stress field in addition to the strength and physical properties of the coal, immediate roof, and immediate floor strata. Quantifying the vertical stress field is complicated by the combination of the overburden stress, abutment stresses transferred onto the barrier pillar from adjacent gob areas, and in multiple seam mining, stresses transferred from abandoned subjacent mines. These variables make the extraction and development of barrier pillar reserves a site specific consideration. Three case histories are presented in which barrier pillar development and extraction provides; i) an access point and the means to ventilate a large area of low seam reserves left by a prior operator after developing only the thicker areas of a multiple split reserve, ii) the means to increase total recovery of a deep, thick seam longwall reserve, and iii) opportunities for the development and retreat mining of a two mile long barrier pillar in thick seam reserves.

Jan 1, 1995

By Collin Stewart

Bowie Resources, LLC (Bowie) has been using the Stability Mapping System (SMS) developed by Dr. Keith Heasley, West Virginia University, since 2005. Seven three-entry longwall gateroads, four longwall panels and a five-entry set of mains have been mined in two different seams in areas originally analyzed with the SMS. This paper compares predictions of mining conditions based on the SMS with actual mining conditions. Specific comparisons include longwall and continuous miner (CM) productivity, longwall tailgate response and support and CM roof bolting requirements. The paper also discusses current thoughts at Bowie on the use of different weighting factors for CM development, longwall face conditions and longwall tailgate support requirements.

Jan 1, 2007

By Patrick S. Artrip

A deep mining operation in the Lower Kelly (Imboden) seam in Wise County, Virginia experienced severe ground control conditions in its attempt to develop reserves situated under increasingly higher cover conditions. Ultimately one of only three mines capable of providing access to a large reserve area had to be abandoned. A thorough geotechnical exploration program was carried out to allow characterization of the critical roof and floor rock strata in accordance with the modified geomechanics classification system. The principal roof and floor rock stratigraphic sequence types were defined and mapped throughout the reserve area along with other critical geological factors. A ground control study based on the geotechnical findings provided a quantitative analysis of the causes of previous entry instability. Further analysis of pillar and entry stability identified configurations which would remain stable for the variety of strata types and range of overburden depths within the remainder of the reserve. Mine designs based on the geotechnical evaluation have, to-date, provided the stability required for long-term future development - of the reserve area. However, some areas of difficult ground were encountered which could not be anticipated with the drill data available at the time of the original study.

Jan 1, 1993

By Bolger Witthaus

"High performance production under challenging geological conditions is a product of several parameters. Main factors are the technical equipment and the knowledge in processing. The design and the support system of maingates must also be taken into consideration. The extraction of seams in German underground hard coal mines of RAG in a range of heights between approximately 1.1 and 4.0 m ( 4 and 13 ft) is done by plow and shearer technology. A complete system for quality management of production is required. The process examination of processes begins with procurement of the equipment. Education and training of the engineers and specialists, as well as for the miners are requirements for success as well.This report gives an overview of RAG measures for achieving high performance. Starting with examination of the processes accompanying procurement of equipment, the following important elements are described. Standards in education and training, technical design and elements of automated processing using stateof- the-art in control systems are critical to this system.The application of automation plays a decisive role in modem coal mines. The latest development in German coal mines is the fully-automated shearer system for longwalls. This helps to enhance safety, particularly in difficult ground conditions, by removing the shearer and shield operators from the immediate mining activity.INTRODUCTIONLongwall mining in carboniferous strata in Germany faces various challenges. Different longwall systems are used to mine up to 24 seams, each with a thickness between 1.1 m (3.6 ft) and 4.0 m (13 ft). High stresses due to a depth of up to 1,400 m (4,593 ft) requiring pillars between the panels, require special systems for roadway development, roadway support and reinforcemen.t as well as for longwall advance operations. Two main types of equipment for extraction are shearer and plow systems. While shearers are utilized for seam thicknesses above approximately 1.8 m (6 ft), plow systems can be used for smaller seam thicknesses between 1.8 m (6 ft) and approximately 1.0 m (3 ft)."

Jan 1, 2010

By Kanaan Hanna

Abandoned mines pose a serious threat to public health and safety, as well as the environment. When active workings approach old mine workings, miners could encounter significant hazards. Additionally, the presence of mined-out areas or voids underlying residential/commercial properties, transportation, and infrastructure systems can cause subsidence issues ranging from differential settlements and sinkholes to catastrophic collapse. All these features can result in adverse impacts in terms of cost and public safety. Traditionally, mine void detection and related engineering investigations for mine subsidence risk assessment and mitigation have been greatly dependent on systematic drilling and grouting backfill programs. The unknown location and condition of abandoned underground mines represent significant challenges to geologists and engineers in accurately evaluating subsidence hazards and developing appropriate mitigation measures. A comprehensive, multi-phase mine subsidence investigation was conducted at an abandoned western U.S. mine site. The mine operated in an approximately 8-ft (2.4-m) -thick coal seam using room-and-pillar extraction from 1919 to 1922. The mine lies at depths ranging from 50 to 100 ft (15 to 30 m), and it is overlain by critical pipeline and utility corridors. Any future subsidence/ sinkhole that occurs beneath or adjacent to the corridors could pose a significant threat, specifically to the structural integrity of the pipeline corridor. Therefore, the engineering geophysical investigation was initiated to determine the potential subsidence risk. This paper describes a recent success achieved by using integrated engineering geophysics in subsidence risk evaluation. A summary of significant results with emphasis on subsurface characterization, mine workings and voids delineation, modeling analysis, and high risk zones identification and mitigation strategy is presented.

Jan 1, 2011

By Thomas Barczak

Hydraulic cylinders are used in several roof support systems, such as longwall shields and mobile roof supports, to provide critical ground control Many state-of-the-art hydraulic support system operate at pressures as high as 7,000 psi to provide the necessary support capacities Pressure in the upper stages of multi-stage cylinders can be intensified by a factor of 2 or 3 providing pressures of 20,000 psi or greater. A proper understanding of the operation of these high pressure systems is necessary to safely maintain and repair these support systems. Likewise, the performmce characteristics need to be fully understood to evaluate the impact of design parameters on the capability of the support to maintain effective ground control This paper examines the basic operating principles of state-of-the- art hydraulic cylinders and discusses relative issues pertaining to. (1) setting loads, (2) support stiffness, (3) yielding behavior, (4) errors in assessing support loading, and (5) hydraulic failure mechanisms and how to detect them

Jan 1, 1998

By Kevin J. Ma, John Stankus, Dakota Faulkner

"Expandable rock bolts are widely used in hard rock mines as an efficient ground control product. However, capacity and service life can be significantly reduced if the metallic body is subjected to corrosion. In some hard rock mines in the U.S., highly corrosive ground conditions exist, and it has been reported that inflatable rock bolts have corroded within a few months after installation. To provide mining industry a cost-effective inflatable bolt and combat the corrosion issues, Jennmar Corporation, Inc., and its subsidiary Keystone Mining Services, LLC (KMS), analyzed corroded bolt samples, identified root causes, evaluated properties of various coating materials, and developed a new inflatable rock bolt, Python M3TM, that is protected with an innovative PyFlexU2TM coating. The new generation Python M3 features improved steel chemistry for reliable performance, modified profile for better inflation, and surface preparation and coating application. The PyFlexU2 is impervious to liquid and air, durable, and UV resistant. With a flexible adhesive, and highly corrosion-resistant undercoating, and a very hard sacrificial surface coating, the PyFlexU2 coating system provides the Python M3 superior protection against chemical corrosion and physical scratch damage. The under-coating has exceptional flexibility and adhesion to prevent coating micro-cracks or fractures after bolt inflation and possesses excellent corrosion resistance to acids (pH <3), alkalis (pH >11), fuels, and salt solvents. The corrosion and scratch resistant PyFlexU2 coating offers very effective bolt protection for extra longevity in highly corrosive environments. The Python M3 coated with PyFlexU2 has been tested in the most challenging conditions, including laboratory corrosion tests in extreme acidic and basic solvents, rock slurry, and borehole scratch insertion tests. With demonstrated corrosion and scratch resistance, the product has been greatly welcomed by hard rock mines in the West and is currently installed in large scale. This paper identifies the root causes of the bolt corrosion, discusses the analysis process, and details laboratory and underground tests carried out on the Python M3 coated with PyFlexU2. The Python M3TM and PyFlexU2TM are subjects covered by pending U.S. Patent Applications assigned to FCI Holdings Delaware, LLC."

Jan 1, 2017

By Dan Payne

Roof falls and other ground control incidents make up a significant portion of fatal accidents in underground mines. BHP Billiton has undergone a review of all fatalities in their operations and divided these into 10 fundamental categories of which underground ground control is one. Each underground roof fall fatality was investigated and the root causes workshopped to develop a protocol for the control of fatalities due to falls of ground. This protocol sets out 22 requirements which each BHP Billiton underground mine site must comply with. This paper describes the development, requirements and application of the protocol within BHP Billiton.

Jan 1, 2006

By Yun Zhang, Haijun Jiang, Shenggen Cao, Chen Wang

The distribution of front abutment pressure is closely related to the force, deformation and energy distribution of hard roof before periodic weighting. So it is necessary to carry out research on the relationship between them. According to front abutment pressure distribution feature, using the location of peak front abutment pressure as the dividing point, coal seam is divided into two parts along the direction of mining: the yield zone that is the area between the faceline and the point where the maximum front abutment pressure occurs, and the elastic zone that is the part before the point of peak front abutment pressure. The proposed mechanical model of unit width hard roof at the panel center periodic weighting consists of five parts including the yield zone. All parameters of the deflection equations for each of the five parts that satisfy the continuity conditions and natural boundary conditions are obtained by using the Matlab software. The continuous curves of front abutment pressure, deflection, bending moment and bending strain energy density distribution of hard roof are obtained by iterative approximation method. The following conclusions can be drawn through analyzing those curves: (1) The position of peak front abutment pressure is located at the transition of coal seam foundation from yield zone to elastic zone (elastoyield critical point), the distance of it to the faceline is equal to the width of yield zone. The peak front abutment pressure increases with yield zone with. (2) The peak bending moment in front of the faceline, and the distance of it to the faceline increase with the yield zone width. The deflection of hard roof at the face and midspan also increase with yield zone width. (3) As the yield zone width increases, the accumulated elastic energy of hard roof in front of the faceline increases, and the core zone of energy moves forward away from the face. (4) When the yield zone width is zero, the whole coal foundation is regarded as elastic foundation, and the peak front abutment pressure occurs at the faceline.

Jan 1, 2015

By Qiang Fu

ABSTRACT This paper aims to identify the main issues concerning top-coal loss and the optimum drawing interval of LTCC (Longwall Top-coal Caving) mining by underground tests and DEM (Distinct Element Method) modeling. By extracting a new roadway in the goaf of the mined LTCC Panel No.4318 in Wang Zhuang coal mine of Lu-an CMA (Coal Mining Administration), and underground observation of the distribution of loss coal and broken rock in different sections of the roadway, this paper analyses the composition and presents a 3-D distribution map of the loss coal in the exploration roadway. This study indicates that the DEM modeling of broken top-coal is reasonable and scientific as it can simulate the movement of broken coal and waste rocks and determine the optimum drawing interval of top coal.

Jan 1, 2002

By Pinnaduwa H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior of the rockmass surrounding the underground mine excavation. The aim of this study was to investigate, at the threedimensional level, the geotechnical behavior around a tunnel excavated in a metal mine in China. A three-dimensional numerical model was built by using the 3DEC software package to simulate a tunnel excavation under a high in situ stress condition and by relying on the information available on lithology, geological structures, in situ stress measurements, physical and mechanical properties of intact rock, discontinuities, and interfaces between different rocks. The authors also investigated the effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or equivalent continuum material and rock support system on the deformation, and stability around the tunnel. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses with appropriate geomechanical property values.

Jan 1, 2013

By Xu Lin Sheng

During the mining course, when the roof above coal seams is constituted by thick and hard sandstone (conglomerate), sudden roof movements often take place with great force and de¬struction which is the biggest danger to the safety and production. Such sever movements of the roof in mining directly relate to the rock mechanical properties which are the main fac¬tors that influences the regularity of hard roof movement and its destruction form. A significient work and important technical way for applying rock mechanics into mining en¬gineering is studying the rock mechanics of the hard roof and altering some of the rock me¬chanic parameters which induce the improvement of the rock properties in order to efficiently control the movement of the hard roof.

Jan 1, 1989

By A. Mahyera

BETTER ROOF SUPPORT During the last decade, resin-grouted roof bolts have taken a substantial foothold in the coal mining industry - now accounting for about one-third of all bolts installed annually, due to the improved roof support. However, the high cost, toxicity and flammability of the resin cartridges appear to be a limiting factor in even greater use of such bolts. Terra Tek, Inc. has, over the past few years, been developing a novel roof bolting system to mix/inject a very fast-setting and high strength inorganic cement into bolt holes and install point-anchored or full-column grouted rebars - all automatically and at substantial cost savings. This grouting system utilizes a unique method to mix the grout ?in-the-hole?. It has been integrated with a conventional bolter, retrofitted with an indexing-head mechanism and an on-board pneumatic computer to sequence and Control the drilling, grouting and bolting. Cycle times are the same or better than for a resin system. Following laboratory testing/development, the prototype system has undergone field trials in a Utah coal mine. A description of the bolting system, results of pull-tests in the laboratory and field, and economics and productivity gains with this system in comparison to a conventional resin-cartridge bolting method are presented. The relationship of this technique to improved roof control is also discussed.

Jan 1, 1984

By N. P. Kripakov

The U.S. Bureau of Mines (USBM) is conducting research to develop a practical computer-based tool that will allow coal mine planners to anticipate rock mass behavior surrounding mine entries prior to actual mining. More specifically, this tool estimates to what degree and extent the immediate roof and floor strata and the coal pillar ribs surrounding an opening will weaken or fail for a given set of mining parameters. The technical approach couples together two numerical techniques: the boundary-element method and the finite-element method to allow for an approximate three-dimensional simulation of actual mining situations. Outputs from plan-view, linear-elastic, boundary-element models executed at different mining stages are used as input to a detailed, section-view, finite-element model to estimate the degree and extent of failure expected to occur around the periphery of an entry system. Using a pseudo-elastic approach. elastic rock mass properties are continually updated as different zones are predicted to fail. The procedure is relatively easy to use and is being set up to work interactively with the user who will not be expected to be a computer expert. Inputs include easily understood parameters obtainable from the field and rock mechanics laboratories. Examples of computer-generated output from generic sample models representing typical mining situations are presented and results discussed.

Jan 1, 1994

By Bob Thomas

The roof drill operator productivity can be enhanced by the introduction of control technology The operators control station can be improved by considering human factors such as handle forces and control location. The smaller electrical controls can be located much easier than the traditional hands on valves. The operators control can he improved by using processors with programmable subroutines that assist the operator in the decision making process. For example to increase feed rate - to slow rotation - to avoid clogged steels - etc. The overall affect is to improve drilling and bolting consistency. The control system uses a dedicated processor packaged as an intrinsically safe control station. The roof drill operator is assisted in the drilling; arid bolting by a closed loop feedback system. The processor monitors the drilling parameters such as feed force, feed rate, rotation torque, RPM, drill position, and vacuum condition Based on the drilling parameters the processor executes pre-determined condition statements intended to enhance drilling The drill operator has an active display to alert him to the real time machine status. For example if the feed were to slow or delay due to a high vacuum level the display would show "high vacuum". The dedicated processor is available on the arm feed style machines, The prototype machines used programmable logic controllers to develop the feedback relations. The ability to record drilling parameters was extremely helpful in this development project. The extended use of the recording feature will aid operators in mapping the mine roofs Interpreting the recorded drilling parameters can reveal a void in the top or hard competent drilling The prototype machines also showed the importance of vacuum monitoring This feature is extremely valuable in softer materials, The benefits of the control system range from efficient use of the consumable bolting materials to uniform operator performance.

Jan 1, 1999

By John C. Stankus

At the 13th Conference on Ground Control in Mining, a paper was presented detailing a successful test in which a new truss system was utilized, in lieu of wood cribs, for tailgate support in the Pittsburgh seam (Stankus et al., 1994). Since that time, additional tests using this same truss system in the Pittsburgh and other seams are now complete. Also, several mines are now using trusses for full panel tailgate support with no cribs. Through an extensive instrumentation program, much data and new information has been gained from these tests and the full panel usage. From this data, not only have new concepts pertaining to tailgate support been developed, but also for headgate, pillar configuration, primary and supplemental support. In this paper, an update will be presented summarizing the results of these various tailgates.

Jan 1, 1995