Search Documents

This study was conducted to evaluate the effects of a diesel particulate filter (DPF) regeneration process on the concentrations and size distributions of aerosols in an underground mine. Two active regeneration strategies were examined for an electrically regenerated sintered metal fiber filtration system, and the effects were compared with those observed for a muffler and the same system operated in a passive configuration. The effects were assessed for three steady-state engine operating conditions. The number and mass concentrations and size distributions of aerosols in mine air were found to be strongly affected by the exhaust configuration, engine operating conditions and the regeneration process. When the system was operated in active configurations, the concentrations exhibited a transient and cyclic nature. At light load conditions, the distributions of aerosols in mine air were dominated by accumulation mode aerosols for all exhaust configurations and regeneration strategies. High concentrations of nucleation aerosols were observed when the DPF system was used and the engine was operated at high load conditions. A positive correlation between accumulation of particulate matter in the filter and the efficiency of the filter in removing accumulation mode aerosols was observed for all conditions. In the case of high engine load, reductions in accumulation mode aerosol concentrations were linked to a substantial increase in number concentrations of nucleation mode aerosol. Overall, the filtration system was found to be very effective in reducing total aerosol mass and elemental carbon concentrations for all engine operating conditions. However, the system was substantially more effective in passive than in active regeneration configurations.

Jan 1, 2012

By R. Asmatulu

According to Darcy's law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By H. Kinilakodi

The authors previously had developed a methodology that combines injury and citation measures into an overall mine safety performance evaluation tool, called the Safe Performance Index (SPI). It can be easily adopted by mine operators to monitor trends in their injury and citation experiences as a risk assessment method. In this paper, six normalized safety measures and the SPI are used to evaluate the risk that existed at mines in the two years preceding the occurrence of a fatality. The percentage of mines is given for which the risk was high or where trends of some of the safety measures indicated moderate risk. In 50% of the mines, this mine safety performance tracking method could have been helpful to the companies, state agency, or MSHA in recognizing and addressing emerging problems with actions that may have been able to prevent high-risk conditions, the fatality, and/or other serious injuries. The approach would have given scrutiny to the risk for mines that encompassed 74% of the fatalities during 2007-2010.

Jan 1, 2012

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level. It is situated in a wide east-west valley. Minera Peñasquito, S.A. de C.V., wholly owned subsidiary of Goldcorp Inc. has operated twin SABC-flotation lines since June 2010. Each line is capable of processing 50,000 tonne per day using a SABC grinding circuit followed by flotation to produce lead and zinc concentrates. The addition of a Polysius Polycom HPGR 2417 with dual 3,000 kW drives to reduce the crushed pebbles produced by the SAG mills was planned to increase production to 65,000 tonne per day per line. The production has been limited to 100,000 tpd due to operating issues in the grinding circuit. The operating issue has been the amount of pebbles generated by the SAG mills is significantly less than originally planned. This paper describes the planned installation of a crushed augmented feed to maximize utilization of the HPGR capacity. This coupled with full utilization of the SAG and Ball Mill available energies there is the potential to achieve a 50% total capacity increase from the grinding circuit.

Jan 1, 2012

By Allan Breitenbach

Leaching has been used since the 1600s on unlined ore dumps and since the late 1970s on lined leach pads for the recovery of metals from mined ore, the latter typically called ?heap? leaching and the former ?dump? leaching. Modern day run-of-mine (ROM) or crushed ore heaps are stacked in controlled lifts on lined leach pads and irrigated with a solvent solution (dilute alkaline cyanide for precious meals, dilute sulfuric acid for base metals and uranium). Conventional lined leach pads store process solutions and any storm water, snow melt and cumulative wet season surplus water by gravity flow to external ponds. Impounding valley leach pads (also known as valley fill heaps) differ from conventional leach pads by storing various combinations of process liquid solution and surplus water within internal ponds by using the interstitial pore volume of the ore. While impounding liquids within the heap is simple in concept, impounding leach pads are more complicated for construction and containment compared to conventional leach pads with external ponds.

Jan 1, 2012

By Yi Luo

Subsurface strata movements and deformations caused by longwall mining operations in underground coal mines could affect many important coal mining activities, such as gob well degasification, ground water protection and multiple seam mining. The stratifications in the overburden have significant influence on the subsurface and surface movements and deformations in the ground subsidence process. An enhanced subsurface subsidence prediction model considering overburden stratifications has been introduced in this paper. In this method, the entire overburden strata are equally divided into a finite number of layers and the percent of the hard rocks in each layer is an additional input. The proven influence function method is applied to predict the subsidence on each of the predefined layers progressively upward using the predicted subsidence on the previous layer as the subsidence cause for the current layer. A computer program is developed to facilitate the calculations. A case demonstration is used to show the applicability of the proposed subsurface subsidence prediction model.

Jan 1, 2012

By F. M. Jenkins

Improvements in miners? safety and health, as reflected by injury and illness statistics, have reached a plateau and even been reversed. Research into miners' OSH is a necessary adjunct to regulatory enforcement. Under the National Occupational Research Agenda (NORA) mining experts have come together to draft a national agenda for this research. The Mining Sector Council, one of ten NORA Sector Councils, has produced a draft national research agenda to guide all mining research entities: academia, government, and industry. The agenda has seven major objectives, each of which has a sequence of sub-objectives: Reduce the likelihood of disasters in mines; Improve mine disaster response; Improve the health of miners; Improve atmospheric control (ventilation) in mines; Improve health and safety through behavioral research; Improve mine design, systems operations, and management performance to enhance mine health and safety; Apply ergonomics, human factor engineering, to increase health and safety. Long-term maintenance of the Mining Research Agenda requires input from the public, both here and abroad, monitoring of the impact of research results using OSH data, and partners who will translate the research to practice.

Jan 1, 2012

By M. L. Chapman

When originally accepting the assignment, the Client had described the property as vacant land. A prior appraisal was later discovered and revealed that the property included a mineral rights appraisal. Further research disclosed an old dispute with a court ruling based on testimony by AIMA-certified experts. The present appraisal was therefore based on data from findings of the court with a fresh look at discount rate, absorption period, and residual land value. Fortuitously, the property subsequently sold on the market, while meeting all criteria for Fair Market Value. This provided insight into a market-based discount rate. Also, the absorption period could be adjusted in accordance with the current market conditions. The residual land value was minimal (based on comparable sales and projecting trends in market) as the property was affected by a flood zone and the surrounding development was sparse. PROPERTY HISTORY: A GREAT INVESTMENT Briefly, the subject property is located in the floodplain region of the San Jacinto River, a short river in southeastern Texas that flows into Galveston Bay, filled with sand and gravel. This location is on the north side of Houston, north of Beltway 8 on the east side of I-59.

Jan 1, 2012

By F. Khorram

Image processing is a technique that simulates the human vision system. This technique enables applying every statistical or intelligent operation to recognize differences. In this way this new technique is used in quality control systems in most industries. Studying sedimentary rocks is very important from the economic point of view. Some units of sedimentary sequences involve different mineral deposits, hydrocarbon and water resources. Therefore it is important to identify and classify different sedimentary rocks. Descriptive classification of sedimentary rocks is usually based on visual and textural features and chemical composition of a sample. In this paper different samples of a limestone mine in central part of Iran are classified. The samples were collected from different parts of the mine and crushed down in size from 2.58 cm to 3.58 cm. The rock samples were labeled based on percentage of chemical and lithological compositions. Each sample was assigned to one of the distinguished groups. The images of the samples were taken in appropriate environment and processed. A total of 74 features were extracted from the identified rock samples in all images. In order to feature dimensional decrease, principal component analysis method was used. Then Bayesian statistical algorithm was used as a useful tool for classification. Classification Correctness Rate (CCR), calculated for the test data sets are %88, %68, %61 and %72 for the first to fourth class respectively. Therefore it can be inferred that the extracted features of images are appropriate indicators for different samples identification. These precise results besides the advantages of image processing technique, which are increasing speed of operation and decreasing cost, appears to be a desirable success.

Jan 1, 2012

By K. Awuah-Offei

Energy efficiency has become significant due to cost and environmental considerations. Comminution and material handling have been identified as the two most energy intensive processes in mining. The objective of this work was to evaluate truck-shovel energy efficiency strategies using discrete event modeling. Energy audits and time and motion studies were conducted at a surface coal mine to acquire data. A discrete event simulation model of truck-shovel operations was built in Arena® and validated with the field data. The model was used to evaluate the effect of using a larger shovel, and optimizing truck-shovel matching on fuel efficiency. The results indicate that using a larger excavator increases the fuel efficiency of the operation while optimizing truck-shovel matching does not. However, using a larger shovel will lead to under-utilization of the shovel. This work shows the potential benefits of using discrete event simulation to model energy efficiency of mining operations.

Jan 1, 2012

By J. Kretschmann

Around the world, mining has been done for thousands of years for the benefit of humankind. The winning process in mining operations ends with the depletion of the deposit or its closure if the operation becomes economically unprofitable. After that, a period of post-mining follows which may last for a very long time and which is generally regarded as a period of hazards, risk and high cost. In the USA alone, approximately 500,000 abandoned mines do exist; worldwide, there are millions. In Germany, too, we have had to deal with abandoned mines for a considerable period of time now.

Jan 1, 2012

By Stephen P. Mulqueen

Searles Lake is an evaporite basin located near the community of Trona in northwestern San Bernardino County, CA. Searles Valley Minerals Operations Inc. (SVM), a subsidiary of Nirma Limited, currently manufactures more than 1.58 Mt/a (1.75 million stpy) of industrial minerals from natural brines produced from several lakebeds within the basin. The chemical manufacturing facilities in Searles Valley represent extremely complex operations involving solution mining and mineral extraction processes.

Jan 1, 2012

In the grand scheme of things, the 9.5-t (21,000-lb) shipment of molybdenum concentrate that left Freeport-McMoRan?s Climax Mine site on May 10, 2012 was not unlike the thousands of others that have been hauled away from the site during the last century, except for the fact that this shipment marked the official rebirth of one of America?s greatest mines. For nearly two decades, 17 years to be exact, there was no production from the mine that was once the largest underground mine in the world and was so important to the Allies? effort during World War II that it was assigned the highest priority of any mine in the United States by the War Production Board. The economic recession in 1980 put an end to the mine?s success, and the Great Recession of 2008 nearly derailed the mine again. But, like the nearby town of Leadville, CO, the mine survived thanks to an investment of more than $700 million by Climax Molybdenum Co., a Freeport-McMoRan company, to bring the Climax Mine back into production.

Jan 1, 2012

By Trevor R. Ellis

In August 2011, the Southern African Institute of Mining and Metallurgy (SAIMM) contacted mining institutes and related societies internationally to assess their interest in participating in coordination of the review of the South African Code for Mineral Valuation (SAMVAL) with reviews of other mineral valuation standards. The main mineral valuation standards are the CIMVal Standard of The Canadian Institute of Mining, Metallurgy and Petroleum (CIM), the VALMIN Code of The Australasian Institute of Mining and Metallurgy (AusIMM), the SAMVAL Code, and the extractive industries? guidance note of the International Valuation Standards Council (IVSC), Valuation of Properties in the Extractive Industries, GN 14, designed for application within the full set of International Valuation Standards (IVSs). By January 2012, SAIMM had concluded that the level of respondent interest was adequate to organize a meeting. A meeting was scheduled for April 18, 2012 in Brisbane, Australia in conjunction with a VALMIN mineral valuation conference organized by the AusIMM. The stated purpose of the meeting was to develop an accord on terms of reference for pursuing harmonization of mineral asset valuation standards adopted by the participating mineral institutes. SME decided that, although it has not developed its own mineral valuation standard, it should participate in the Brisbane meeting and the harmonization process, as also did the American Institute of Minerals Appraisers (AIMA).

Jan 1, 2012

By T. Robyn

The Bolivar Cu-Zn skarn deposit in the Piedras Verdes mining district of Chihuahua is one of many base and precious metal deposits in the north-northwest trending Sierra Madre Belt extending across the states of Chihuahua, Durango and Sonora in northwestern Mexico. The information presented here is drawn from two papers on the Bolivar property1,4 plus new information. Historical mining and exploration for polymetallic Cu-Zn-Pb-Ag-Au deposits in the Sierra Madre Belt dates to Spanish Colonial days. Access to the Bolivar Property (Figure 1) is by paved road (approximately 305 km southwest from Chihuahua) and approximately 80 km by all-season gravel roads to the villages of Cieneguita (population ~1,000) and Piedras Verdes (population ~500) adjacent to the property. [ ] The Bolivar property comprises an old Cu-Zn producer (the Bolivar Mine), exploration concessions adjacent to the Bolivar Mine, and a new camp at the mine that supports mining, exploration and maintenance. From 1980 to 2000, former operators extracted approximately 300,000 tonnes of ore that was hand sorted to an average grade of 5-6% Cu and 25-30% Zn. From 2005-2010, Dia Bras produced from the mine just over 600,000 tonnes at an average grade of 1.7% Cu and 8.6% Zn. Dia Bras transported mineralized rock 275 km by truck and rail to its Malpaso mill, located about 30 km west of Cuauhtémoc in central Chihuahua, from 2005 until October 2011 when the new Piedras Verde mill was commissioned only 5 km from the mine. (Note: the Company cannot use the term ?ore? because it has never completed a feasibility study.)

Jan 1, 2012

By T. Wang

A new generated NaNO3 ? NaNO2 ? KNO3 ternary thermal energy storage system which has low melting point as 124°C and high specific heat capacity was studied for the short and long?term thermal stability by using the Thermogravimetric Analyzer (TGA). Based on the actual working condition of molten salt in solar two, the simulated cyclic thermal stability measurement was also conducted. The ternary system demonstrates excellent short ? term thermal stability and thermal reliability after cyclic heating and cooling processes. However, in the long ? term as well as the simulated cyclic stability measurement, large amount of weight loss was observed. Moreover, the stepwise long ? term isothermal study reveals that below 440°C the weight change is minimal and this temperature is viewed as the upper limit temperature of thermal stability for this ternary system. To determine the lost phases at high temperature above the upper thermal stability limit, techniques such as XRD and SEM are used to compare the condition of the salt mixture before and after the long ? term thermal stability study. On the basis of the comparison, it can be concluded that the major weight loss was due to the decomposition of sodium nitrite.

Jan 1, 2012

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert systems designed for real-time processing plants that also include the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. [1,2] In spite of the fact that significant performance increases have been achieved using these systems they are not perfect and can be improved. They suffer from the static nature of their rules and to a degree the process models. There is an opportunity to further increase system performance by systematically taking advantage of the tremendous amount of data produced by the expert system to improve the design, the heuristic rules, the model topologies and the use of the models. Data mining refers to extracting or mining knowledge from large amounts of data where the objective is to automatically analyze, classify and summarize the data to automatically discover and characterize trends in it and to automatically flag anomalies. [3] Clearly, modern process control systems are capable of collecting vast amounts of data. Without a doubt, these data contain important information on the operation of our plants and their ultimate optimization. Coupling the information mined from these data with Expert Control Systems should produce more effective control and greater knowledge of the grinding process and the flotation process. Now, with the advent of effective monitoring of entire minerals plant electric consumption it is possible to not only optimize plant production in real-time it is possible to analyze total plant electrical consumption and incorporate it into the plant control logic thereby improving the overall plant economic performance. This is particularly important with the ever more complex power contracts that plants operate under.

Jan 1, 2012

By Michael Rehbock-Sander

The Gotthard Base Tunnel (GBT) is 57 km (35 miles) long and consists of two par-allel single-track tubes with an ex-cavation diameter ranging from 8.8 to 9.5 m (28.8 to 31.2 ft). These are interlinked by cross-passages every 312 m (1,000 ft). Two multifunction stations (MFS) are located in the sections Sedrun and Faido, at one-third and two-thirds of the entire tunnel length (Fig. 1). These will be used for the diversion of trains to the other main tube via tunnel crossovers, for the housing of tech-nical infrastructure and equipment and for potential emergency stops. To reduce construction time, the GBT was divided into five sections and was excavated from several sites simultaneously. The tunnel was excavated from the two portals, Erstfeld in the north and Bodio in the south, and also from three intermediate attacks, with their corresponding access tunnels, in Amsteg and Faido and two vertical 800-m (2,624-ft) deep shafts in Sedrun.

Jan 1, 2012

By A. D. Davis

Limestone-based material shows great promise for removal of arsenic from water. In laboratory tests, it has removed more than 95% or arsenic and more than 99% of cadmium and lead. In addition, the waste material appears to be suitable for recycling or disposal in an ordinary landfill. However, the efficiency of limestone for arsenic removal could be improved. Recent research has shown that iron treatment of limestone can enhance its arsenic-removal efficiency greatly, increasing its attractiveness as an alternative to other methods.

Jan 1, 2012

By S. Ragab

The objective of flotation models is to predict the recovery rate of minerals from a flotation cell. In this paper a CFD?based flotation models is presented. The model uses first order rate equation, and the collision frequency is estimated using Abrahamson [1] model with input from CFD two-phase simulations. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) are determined by the two-phase hydrodynamic simulations. Knowing these parameters throughout the machine is essential in understanding the effectiveness of different components (rotor, stator or disperser, jets) on the flotation efficiency. Not only the average pulp recovery rate can be estimated but also the regions of high/low recovery rate can be identified. The CFD-based flotation model presented here can be used to determine the dependence of recovery rate constant at any locality within the pulp on particle diameter, particle specific gravity, contact angle, and surface tension.

Jan 1, 2012