Search Documents

By G. F. Friel, G. S. Morrow, J. C. Edwards

An experimental program in the U.S. Bureau of Mines' Safety Research Coal Mine evaluated the effects of dead end crosscuts on the transport time of CO along a mine entry. The presence of carbon monoxide is a characteristic of a fire in its incipient stage, and is significant in the determination of a fire location in a mine from the analysis of arrival times of pre-set concentrations at CO monitors. In this investigation two entries, with a total of ten crosscuts, connected by a room were instrumented with CO sensors as part of a real-time monitoring and data acquisition system. Controlled release of 1% CO was monitored as the contaminant traveled the entries for several different configurations of CO sensors and exhaust fan settings. In addition to the normal longitudinal dispersion of CO due to turbulent mixing at the front of the CO wave, the induced rotation of air established within a crosscut by the entry flow diluted the CO concentration through entrainment. It was determined experimentally for the entry and crosscut configuration considered that the transport time for a specified CO concentration was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and total crosscut volume. The proper interpretation of the measured transport time of a specified contaminant concentration between sensors is important for mine safety in the isolation of a fire and plans for miner evacuation.

Jan 1, 1993

By Bernard A. Grand, Gary A. Almeraris

This project involves the reconstruction of a 1,100 ft. long by 75 ft. wide segment of an existing 4 to 5 track subway under Northern Boulevard in the Borough of Queens in New York City. The project includes widening the existing subway to permit the construction of new inbound and outbound subway (T1 and T2) ramps adjacent to and under existing operating tracks. The plan of the project is shown in Fig. 1. Existing tall buildings along the job site and a contaminated groundwater plume under an adjacent rail yard required construction of slurry concrete walls along the east and west construction limits. Groundwater cutoff across the north and south construction limits of the subway was achieved by jet grout walls built across the subway invert slab between existing track and third rails. The work involved dewatering the construction site to a depth of about 50 ft. below street grade. This is a four year project and includes extensive work to maintain and protect subway and vehicular traffic of over half a million commuters a day through the work area. The project cost was $160,000,000.

Jan 1, 1999

By W. F. Hahnert, T. L. Ward, K. E. Stoll, P. A. S. Ralston

Fuzzy logic is well suited to the control of non-linear, time-varying, and/or any system for which it is difficult to obtain an exact mathematical model. To design a good fuzzy controller, a thorough understanding of the desired process behavior is required. Many papers have suggested that fuzzy controllers are robust. If they are, it is reasonable to explore whether or not they respond better than conventional controllers to errors in the feedback signal due to imperfect measurement or sensor degradation. It may be the case that simpler or less expensive sensors could be used in some processes. The research presented here relies on an integrated array of computer programs that model and simulate (1) the process to be controlled, (2) common feedback instrumentation, and (3) both fuzzy logic controllers (FLC's) and conventional controllers. Various types of feedback sensor imperfections are imposed upon the system, and the performance of the two controllers is compared. Each controller is tuned to its optimal performance in response to a setpoint change using perfect feedback measurement.

Jan 1, 1993

By Jerry W. Danni, John E. Hardaway

Corporations today must comply with an ever growing number of complex and increasingly stringent environmental laws and regulations. An environmental audit program is an effective means in which to uniformly and systematically assess compliance, and to assure management that environmental liabilities are being minimized. This paper describes the design and implementation of Homestake Mining Company's environmental audit program, which has as its primary focus the objective verification of compliance with external requirements and internal good management practices. Major elements of the audit program discussed in the paper include: pre-audit preparation; on-site audit activities; and the post-audit report.

Jan 1, 1992

By James H. Vignos

An optical instrument designed for the on-line measurement of the size distribution of coarse particles (3-500 mm) being transported on a conveyor belt is described. Included is a discussion of the measurement technique, as well as test data verifying the legitimacy of the basic sensing approach. Field data indicating the instrument's ability to make useful measurements in an industrial environment are also presented. Applications in the mining and mineral industry, for which this instrument was orginally developed, are outlined, with particular emphasis given to the areas of crushing and grinding control.

Jan 1, 1979

By Donald M. Duncan

An acceptable source of concrete aggregate is available in Kansas City in a continuous, medium bedded, slightly dipping limestone unit. Removal is accomplished in shallow depth, 12 feet to 17 feet high, room and pillar mines. The accepted empirical design spaces 20 foot pillars 60 feet on center. A portion of the 20 foot unit is left in place for roof support. Rock and soil cover is variable to 100± feet maximum. Long-term stability of these mines is affected by numerous factors, including the above mine-rock profile, ground water conditions and mining practice. Crusher-run aggregate sells at the mine for $2.20 per ton, yielding a gross income of $2.00 to $2.80 per square foot of mine. Use of mine space for real estate development requires a new perspective in mine development. Mining practices to obtain long term stabile structures can become an over-riding factor as compared with minimum production costs and maximum extraction ratios. Poorly mined areas are unusuable for secondary purposes. Development cost for lease space in less desirable mines is substantially greater than those planned for a secondary use. Real estate development in mine space involves unique engineering problems. Properly engineered developments offer singular advantages. Warehouse lease space sells for $.50 to $1.00 per square foot per year; fully developed office areas may double these values.

Jan 1, 1968

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By Edward M. Belsky

Increasingly stringent government environmental regulations will affect the availability and costs of bonding and insurance products for the mining community. New regulations requiring Environmental Impairment Insurance, Reclamation Bonds, and Cyanide Use Bonds will result in both an increase in cost and a decrease in availability of affordable insurance and bonding pro- ducts. Professional Liability Insurance for engineers that covers pollution exposures will be a must for all professional engineers working in the mining community. By understanding the problem, solutions can be structured to allow your company to obtain the mandated insurance at the most favorable cost and conditions!

Jan 1, 1991

By W. G. Prast

The role of governments as a factor in the international non-metallic minerals industry can take several forms. Classically, the government acts as a taxing agent, collecting part of the economic rent on behalf of the country from private-sector mine operators. In addition to its taxation policies, the state can and does provide the practical commercial framework of regulatory and fiscal incentives and restraints that shape the activities of the mining firms. In addition to its functions as an agent of the public interest, the government can choose to take a more direct stake in the mining industry, and has done so in the instance of several industrial minerals that are actively traded on world markets. In this paper, the actions of three governments are reviewed and the consequences of their actions are examined.

Jan 1, 1981

By J. A. Farinelli

In the Appalachian region of the United States, approximately 40% of the underground coal reserve base exists in seams 0.7 - 1.1m thick. These seams are, in general, often of premium quality and are frequently accessible through above-drainage drift-type openings. Unfortunately, there are no apparent advantages to mining thin seams, if quality is disregarded. The thin-seam mine is faced with the same legal and economic pressures as any other underground coal mine. But in addition to these common problems, thin-seam operations must also deal with the unique problems associated with mining at such a restrictive height. Small-scale, short-lived operations appear to be the most feasible means of mining these reserves. The purpose of this paper is to evaluate the production and safety potential of various thin-seam mining systems. Recommendations will be made regarding present and future thin-seam operations.

Jan 1, 1987

By K. R. Miller

In recent years, surface mine equipment operators in the Campbell County region of the Wyoming Powder River Basin have found new ways to solve old problems. This paper will examine overburden stripping equipment and techniques by focusing on evolving applications for draglines, shovels, and dozers.

Jan 1, 1998

By Robert L. Llewellyn

The Wharton No. 2 Mine of Eastern Gas and Fuel Associates is located about 60 miles south of Charleston, West Virginia in Boone County. Daily production is 6,000 T.P.D. on a two-shift basis. The Hernshaw Seam is mined by conventional equipment with one continuous miner in areas where conditions are suitable. The plant is on Cow Creek .Branch of Pond Fork, which in turn flows into the Little Coal River at Madison, West Virginia. When the mine was opened in 1948, plans were developed to build a dual Baum jig plant complete with mechanical and thermal drying, and because full production would not be reached for several years, it was decided to install only one Baum jig setup although the complete structure was erected. This phase of the plant was placed into operation early in 1949, The rated capacity was about 300 T.P.H. of 5" x 0 raw feed to the jig. Being a drift mine, the 10-ton mine cars are dumped at the Headhouse, crushed to 8" in a double roll crusher, conveyed 780 feet downhill to the picking .house where the +5" slate is removed by pickers. All coal is crushed to 5" and 5" x 0 is conveyed 150 feet to the cleaning plant. Further describing the plant growth, the second jig setup was installed in 1954 to clean the increased production. During this operating period, exhaustive tests had ,been run on the plant bleed which was an overflow from the large sludge tank located inside the plant, When the second jig addition was undertaken, 5-14' diameter and 12-8" diameter cyclones with a 9-disc filter were installed for the solids recovery and water clarification system, However, the circuit was not closed and a bleed of part of the overflows from the 8" diameter cyclones was still necessary, To comply with the State Water Commission regulations on stream pollution abatement, four pumps in series were installed to discharge the waste water behind the refuse pile.

Jan 1, 1959

By F. Montgomery Lyon

Pyritic sulfur in coal occurs as discrete mineral particles, and its liberation and physical rejection is the primary target for coal desulfurization. An acceptable solution to the pyrite removal problem from fine coal is not found in the standard methods of coal cleaning such as jigging, heavy-medium separation, tabling, and hydro-cycloning. Although fine coal is an ideal size for froth flotation, this method, as currently practiced is also unsuitable as the fine pyrite usually floats with the coal. One possible solution to this problem may be the froth flotation of pyrite from coal. This reverse flotation scheme would have the major advantage of removing both free pyrite and locked pyrite-coal combinations. With this possibility in mind, we have, as a first step, compared the flotation and adsorption. characteristics of an ore-pyrite and coal-pyrite with potassium-ethyl-xanthate as a collector 1 Related Research. The action of ethyl-xanthate on coal has been studied 2 by Horsley. He measured the contact angles of coal in distilled water and in the presence of purified ethyl-xanthate. The results indicated that the xanthate was not adsorbed by the coal. Additional contact angle data were obtained to determine the effects of cupric, ferric, and ferrous salts on the system. Then either the ferric or cupric salts were in, solution with the xanthate, there was an increase in the natural contact angles of the coal. This indicated that these heavy metal ions activated the flotation of the coal with xanthate. However, ferrous iron did not act as an activator. Horsley stated that the most attractive explanation was that the xanthate is oxidized to dixanthogen in the presence of the ferric and cupric ions.

Jan 1, 1971

By Helmut Hass, Michael B. Gilbert

The extension of the commuter railway system (S-Bahn) in Leipzig, Germany willrequire the construction of an underground line crossing the downtown area of thecity to tie the Bavarian Station in the South to the Main-Station in the North. The City-Tunnel-Leipzig is currently one of the largest infrastructure projects in Europe. This system extension will have a length of approximately five kilometers. 3.9 kilometers of that length are currently being constructed using either cut & cover construction or tunnelingmethods. The design and construction of this project currently is and will continue facing very significant challenging urban and demanding geotechnical conditions.

Jan 1, 2007

By Legett Garrett

Texas Utilities Generating Company (TUGCo) surface mines lignite for use as a boiler fuel at mine mouth generation stations. Currently, the annual lignite production requirement of approximately 28 million tons necessitates mining across approximately 1,600 surface acres each year. The mining operations, located in Freestone, Panola, Titus, and Hopkins counties, Texas, have drastically disturbed some 13,000 surface acres to depths of up to 110 feet since initial startup in 1971. The TUGCo mining philosophy, a commitment made prior to initiation of mining operations and prior to any mining regulations, includes a return of mined-out land to private ownership in the most useful state possible. In the areas of TUGCo operations, the local economies are based upon agricultural production. Historic land use surveys have typically shown a trend from row crop production to pastureland for cattle production. During the 1960?s, the percentage of acreage devoted to row crop production approached zero with respect to the total acreage devoted to agriculture. TUGCo reclamation operations have therefore emphasized restoration of land to a state that is favorable to cattle production

Jan 1, 1982

By George Dials

Good morning gentlemen. My name is George Dials, and I am [vice] president of the Mining and Reclamation Council of America (MARC). The Council is composed of various companies, individuals, and affiliated state and regional trade organizations representing nearly 3,000 companies directly and indirectly involved with surface coal mining in the United States. I am very glad to be here today to address the Society of Mining Engineers of AIMS. While I do not pretend to be an expert in either geological or geotechnical engineering, I am infinitely familiar with the provisions of the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87) and the Federal regulations that have been promulgated pursuant to that Act. The Office of Surface Mining Reclamation and Enforcement (OSM) was created by P.L. 95-87 within the responsibility for implementing the provisions of the Act and "to ensure that society and the environment are protected from the adverse effects of surface and sub-surface coal mining operations."

Jan 1, 1979

By Richard Weinstein, Richard Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Because of the environmentally friendly nature of dry jig plants, installation permits are often measured in days, not months. There has also been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But air jigging is not right for every application. There are limitations due to particle size, particle shape, moisture and near gravity content. This article explores the evolution of dry jigging. It reviews parameters important for determining the suitability of dry jigging. It also compares historical performance data as measured by imperfection, against results from modern dry jigging technology. The article also presents data from modern dry jig installations.

Jan 1, 2007

By Keith S. Olsen

Any discussion of barite mining is virtually impossible without considering, almost in the same breath, the many other variables, such as beneficiation, transportation, infrastructure and location that impact the economics of a particular barite orebody. My comments will be limited to just the mining aspects of barite orebodies and these observations must be considered in proper context with all other parameters affecting exploitation of a barite property prior to final decision on economic feasibility. In many instances low-cost mining situations are more than offset by high-cost beneficiation requirements. Likewise, there are cases of relatively high-cost mining associated with no or low-cost beneficiation requirements thus permitting economic exploitation. Barite orebodies and occurrences are almost as varied as the number of occurrences. As in most mining situations, the design of a mine plan and implementation of a proper exploitation program must be approached on a case by case basis. Proper and sufficient geologic control of a barite orebody must precede the development of a mine plan. Generally speaking, barite orebodies can and, at many times, do "strange" things; pinch with depth; almost never increase in size with depth, overturn, fault-off, change grade, etc. Due to the extreme variable nature of most barite orebodies, a mine plan and its implementation must be as flexible as possible. The ability to quickly adapt to variable conditions will greatly enhance the economics within a particular barite mining environment.

Jan 1, 1980

By P. J. Stewart, S. Tracy

This presentation describes the operation and features of the WCC Carbon Reactivation Kiln. Particular emphasis is placed on minimizing carbon losses, corrosion resistance, fuel efficiency and the fate of mercury during reactivation in the multiple-tube vertical retort. Detailed laboratory work indicates that there is complete vaporization of mercury in the kiln, no refluxing in the upper sections and distinct advantages in using this type of kiln when sizing collection equipment.

Jan 1, 1993

By William A. Faust

At Gold Fields' Chimney Creek Mine, major reviews of the reclamation and closure plans are done concurrently with the annual mine planning required for budget preparation. This review includes identifying and scheduling reclamation work that can be done within the next few years and development of associated costs. Longer term mine, leach pad and waste dump development are examined to take advantage of any design changes that can reduce ongoing reclamation or closure requirements and reduce costs. The success and cost effectiveness of past efforts are continually evaluated to determine the best methods for reclamation.

Jan 1, 1992