Search Documents

By James J. Scott

Three dimensional photoelastic techniques have been developed which provide information on the state of stress at any point in a model investigated. This investigation utilizes these techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by use of data obtained by observing points in slices from the model with a polariscope and solving data obtained by' the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. Results of this work provide information on the overall stress distribution on points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type.

Jan 1, 1963

By Ted D. Maki, Joseph B. Taylor

INTRODUCTION FMC's Paradise Peak mine, located 13 Ian (8 miles) south of Gabbs, Nevada, became opera¬tional in April of 1986 (Figure 1). It was designed and built by Davy McKee, who was instrumental in equipment design and selection. It is the 7th largest gold deposit in the United States with defined reserves of 10.9 mt (12 million st) containing 34 million gms (1.1 million tr oz) of recoverable gold and 933 million gms (30 million tr oz) of recoverable silver. The mine extracts ore by the open-pit method, taking advantage of a 1.5:1 stripping ratio. The mill operates at a 3600 mt/day (4000 st/d) capacity. Crushing is done in three stages to achieve an ore size of minus 0.635 cm (0.25 inches). Grinding further reduces the ore to 85% minus 100 mesh. The ground ore is treated with cyanide in agitated leach tanks and then washed in the counter-current decantation (OCD) thickeners. Zinc is added to the clarified, deaerated pregnant solution to precipitate the precious metals. The precipitate is acid digested to eliminate excess zinc, filtered and retorted to drive off contained mercury. The retorted precipitate is then fluxed, melted and poured through cascade molds. Dore bars are cleaned for shipment and the slag is sent to an in-house slag treatment system. ELECTROSTATIC SEPARATION The dry electrostatic slag treatment system at Paradise Peak is the first installation of its kind. Electrostatic separation has been widely used in mineral processing since the early 1950's. A brief discussion of the theory behind the process is helpful to those not familiar to electrostatic separation. Charging and sepa¬rating slags, dry minerals or other materials by ion bombardment is the most common form of electrostatic separation. Millions of tonnes of minerals are processed each year by this method. In an ion bombardment separation, granular material is fed onto a grounded metal cylinder (or roll) and charged by a corona-producing electrode placed above the roll's surface (Figure 2). While both conductors and non¬conductors become charged, only the conductor is able to lose its charge. The charged non¬conductor, as it rests on the roll's surface, "sees" an oppositely charged image of itself in the metal surface. It is attracted to the image charge, becomes electrostatically pinned to, and moves with the roll's surface. The conductive particle also sees an image and is attracted to it. But upon touching the roll's surface, it discharges rapidly to the grounded surface and is thrown free from the roll's surface with a projectile motion. In the case of precious metal slags, the con¬ductive particles would be metallic prills of dore metal; and the nonconductive particles would be the slag, free of metal. Middling grains, generally, are in the form of a metallic prill encased in or incompletely liberated from slag. LABORATORY TESTING A number of precious metal slag samples have been tested in the laboratory. It has been found that the composition of slags vary widely from one refinery operation to another. Typical laboratory procedure is to crush and size the slag followed by two-stage lab-scale electro¬static separation. The conductor fractions from the first and second pass are then combined as a prill concentrate; middlings fraction and clean slag tailings from the second pass are held separate. Selected results from laboratory testing are shown in Table 1. It is important to note in Table 1 that the assays represent overall silver and gold, not metallic values. From experience, the laboratory results are typically lower in grade and recovery than the industrial installations. This is largely due to the hydroscopic nature of precious metal slags coupled with the high local humidity in Carpco's Jacksonville, Florida, location. Relative humidity in Jacksonville can range form 60-95%, while most mining locations in the

Jan 1, 1987

By F. Michael Jenkins, Elaine T. Bowers

Longwall systems are used to mine approximately 50 pct of the world's total coal production. Single entries are the predominate method of longwall development in Europe and Asia where mining conditions are much more severe than those encountered in the United States. During the 1970's and early 19801s, the Bureau of Mines and the coal mining industry invested nearly $20 million in single entry and related research. This report reviews the accomplishments of single-entry research in the United States. Two U.S. single-entry field projects are described; the Sunnyside Single-Entry Project conducted in central Utah, and the Tunnel Boring project conducted in northern West Virginia. Two other important studies are discussed, the Single-Entry Study by NAMCO and the Single-Entry Design Study by Ketron. Inc. This review compares the resulting technology with European counterparts to further assess the utility and efficiency of the U.S. systems, and final1 y, it discusses future research and development options which would lead to safe and productive single-entry longwall development in this country.

Jan 1, 1986

By O. J. Tassicker

The Electric Power Research Institute (EPRI) initiated a program in 1976 to develop and demonstrate an instrument system for on-line continuous measurement of coal properties. The program has focused on the use of Prompt Neutron Activation Analysis (PNAA) for elemental determinations and microwave absorption for moisture determination. One of the major results of the EPRI program is the development of the CONAC (Continuous On-Line Analysis of Coal) instrument, with Science Applications, Inc. (SAI) as the prime contractor and Kennedy Van Saun Corporation as a subcontractor.

Jan 1, 1983

By William Gleason

"Despite the difficult economic climate for the mining industry, more than 6,300 people joined SME for its 2016 Annual Conference & Expo in Phoenix, AZ, Feb. 21-24.Nearly every commodity has been bruised and battered during the past year, leading to one of the more difficult cycles for the industry in the past decade. Coal has taken some of the hardest hits and other commodities, such as copper and iron ore, have felt the sting of a slower growth in China and an oversupply on the market.The difficult conditions could not be ignored, but they did not deter SME from offering a forum for the industry to share knowledge, network with peers and learn about the best products and practices while visiting the sold-out exhibit hall (844 booths and 627 vendors) or while attending any of the 121 technical sessions that were offered.The current state of the industry was one of the overriding themes of the conference and during the challenging times there are often cutbacks as operations look to become leaner and more efficient, however, there is one area that cannot be cut – health and safety.The conference kicked off with a fascinating presentation from Colonel Mike Mullane, a former NASA astronaut who, in 1978, was selected as a Mission Specialist Astronaut in the first group of space shuttle astronauts. He completed three space missions and logged 356 hours in space aboard the shuttles Discovery and Atlantis before retiring from NASA and the U.S. Air Force in 1990.In his speech to a packed audience, he warned of the dangers of cutting corners to get the job done more quickly by guarding against the “normalization of deviance.”Normalization of deviance is a long-term phenomenon in which individuals or teams repeatedly accept a lower standard of performance until that lower standard becomes the norm. Usually, the acceptance of the lower standard occurs because the individual or team is under pressure (budget, schedule, etc.) and perceives it will be too difficult to adhere to the original higher standard. Their intention may be to revert back to the higher standard when this period of pressure passes. However, by getting away with the deviation from the higher standard, it is likely they will do the same thing when the same stressful circumstances arise again. Over time, the individual/team fails to see their actions as deviant."

Apr 1, 2016

By Charles W. Daugherty, James P. Gould, Kenneth R. Ware

INTRODUCTION As illustrated in Figure 1, the Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system (METRO) ultimately will comprise 100 miles of line divided among 10 routes. At this time about 46 per cent of the system is under construction or in operation. Planning and design of an additional 38 per cent is at an advanced stage. Of the 84 miles under development or construction, about 10.4 miles consist of soft ground tunnels, and another 1600 feet of mixed face. This paper describes most of the factors considered by designers in setting grades for such tunnels. It is hoped the paper will be a useful guide to planners and engineers in developing similar transit systems. The problems faced in Washington, including those related to geology, are not so unique that the solutions cannot be applied to other systems. The paper also may be of interest to contractors who have not perceived the logic behind the selection of a particular vertical alignment. An attempt is made to explain the background constraints that make most tunnel alignments a compromise among competing alternatives. Readers might assume that the choice of alignments is largely controlled by geological conditions. In fact this is merely one of many factors to be considered.

Jan 1, 1976

By Matthias Neuenschwander, Andreas Theiler, Patrick Steinle, John Singer, Martin Vogel, Diego Martini, Ömer Ündül, Markus Weh

"Quartz Dust is a major health hazard in underground works, wherever the ground contains quartz and depending on the chosen method of excavation. A research project initiated by the Swiss Tunnelling Society and realized by the Swiss Federal Institut of Technology, Zurich, established a correlation between the potential of quartz dust generation during excavation and well known geotechnical characteristics – the Cerchar Abrasivity Index CAI and the Uniaxial Compressive Strength UCS - of ten typical Swiss rocks. The results are at the center of a new guideline by the Swiss Society of Engineers and Architects on the requirements for early project stages regarding ventilation and logistics in function of the quartz dust related risk of the expected ground type of the project. The approach presented could be applied worldwide, contributing to more effective health protection as well as to better cost stability in underground works. CONTEXT Respirable quartz dust (aerodynamic diameter of particles < 10 micron) is universally recognized as a major workplace health hazard. Chronic bronchitis, silicosis and lung cancer can be caused by excessive exposure to quartz dust, as has been proved by many medical studies. Therefore, the legislations of many nations specify a maximum workplace concentration (Maximale Arbeitsplatzkonzentration MAK, Occupational Exposure Level OEL). In Switzerland, for example, the Threshold Limit Value TLV for respirable Quartz or Crystalline Silica imposed by the Federal Committee on Exposure Levels (Grenzwertkommission) is 0.15mg/m3 air. Some nations refrain from establishing a OEL because of the carcinogenic nature of quartz."

Jan 1, 2016

By David C. Girard, Larry Williamson, Leonard R. Benson, Ronald E. Bizzarri

On the east side of Washington DC, the DC Water & Sewer Authority is developing a Facility Plan for the Anacostia River CSO Control Projects, including 8 to 12 miles of CSO storage/conveyance and flood relief tunnels and associated facilities. The project includes major technical and non-technical challenges, including: completion under a Federal Consent Decree schedule; large diameter (estimated 25 to 35 ft) soft ground tunnels and shafts up to 200 ft depth; operations without use of active flow control systems; and close coordination with several major public and private construction and development projects that are being advanced in the project area.

Jan 1, 2007

By Jackson M. Langton

INTRODUCTION The Morenci-Metcalf district is located on the southern slope of the white Mountains in Greenlee County, Arizona. Both porphyry copper deposits are four to six miles northwest of Clifton, the county seat, and the new Metcalf mine is situated approximately one mile northeast of the Morenci open pit (Figure 1). Chase Creek, a south-flowing tributary of the San Francisco River, dissects the district and separates the two ore bodies. More than 1,200 exploration and development drill holes have been completed in the district and the Morenci-Metcalf ore bodies have been delineated on a 400-foot grid. Recently initiated drilling programs have revealed new data about deeper protore and associated hypogene alteration. This information, correlated with surface mapping and petrographic studies, was utilized to propose a plausible geochronologic sequence for this region. The reasoning behind this study has been helpful in locating new ore beneath leached capping indicative of only protore mineralization. The scope of this paper is to establish a practical solution to a highly theoretical problem of ore genesis and to familiarize the reader with stratigraphic, structural, and mineralogic events responsible for localizing ore in this district. Continued research will possibly alter the proposed time span and relative displacements, but it is doubtful that the order of events will vary significantly. Geochronologic conclusions are therefore presented as general hypotheses and additional geologic mapping,

Jan 1, 1972

By Patrick Oriez, Chris Norris, Alain Mercusot

"Temporary mechanical ventilation is one of the fundamental requirements in guaranteeing a healthy atmosphere in underground construction works in order to protect the health of persons working on the site. It is therefore essential to conceive a system which meets the requirements of the whole of the worksite and for all phases of work which takes into account all aspects pertaining to its design, dimensioning, justification, installation, maintenance and validation. In doing so, the ventilation design and the selected apparatus to be installed shall meet with the degree of health protection and the quality of air of the worksite as defined by the legislation in force in France, through limiting the concentration of the different pollutants associated with the site activities. Consequently, when presenting a mechanical ventilation project, all of the participating parties and especially the contractor make a commitment to guarantee sufficient volumes (or airflow rates) of fresh (non-polluted and oxygenated) air and extracted (polluted) air in order to meet these limitations and maintain them in all conceivable site configurations. This article sets out the most important aspects of the implementation of a ventilation project from the initial design stage through to its application, discussing French legislation, ventilation principles, calculations and techniques with regards to underground construction sites. BASICS OF VENTILATION Mechanical ventilation studies are concerned with all of the site workstations and work phases which are sources of pollution and apply to all zones of the underground worksite with the goal of maintaining the concentration or composition of this pollution below the permitted levels and comply with the following three basic principles which are complementary to one another without being in contradiction. •,The first principle consists in eliminating or limiting as much as possible the emission of any polluting, irritant, or dangerous substances, by specifying appropriate construction techniques and equipment (use of electric motors, combustion engine equipment: filters, tanks, catalyzers, use of less polluting explosives, damping down dust with water or wetting products, damping down and diluting certain gases using water mists). •,The second principle is designed to capture residual polluting substances emitted close to the source in order to prevent them from spreading into the worksite atmosphere (extraction ventilation with ducting up to the source – upstream of the extractor fan – and use of downstream filters before expelling the polluted air to the exterior). •,The third principle involves accompanying the capture of the pollutants with additional blowing ventilation specific treatment of substances dissipated by and distant from the source of pollution (acceleration of the drift air flow in order to confine dust and better capture it, supply ventilation with ducting in order to dilute the gases emitted and discharge them to the exterior)."

Jan 1, 2016

The rheological behavior of high concentrated coal -water slurry (cws), a new liquid fuel, is an important factor in the preparation, transportation and combustion. The conventional viscosimeters designed for Use with true fluids are not suitable to the measurement of the rheological behavior of cws. So that a special viscosimeter of tube type for cws was designed and set up in .laboratory. Experiments using two kinds of cws from two provinces from P. R. Olfna were conducted. It is found from test results that the experimental cws possess the rheological character of Bingham fluid and there is the existence of the wall effects which causes the measurement errors. In our former paper published the wall effects were discussed III the light of methods of Odroyd and Jastrzerbsiki to make the correction of the experimental results. But a number of tests are necessary to meet the need of determining the slip coefficient. In this paper the models of the wall slip velocity and the thickness of the slip layer of Bingham fluid were proposed III in theoretical approach which were satisfactorily used in the correction of the measured results of the rheological character of cws.

Jan 1, 1994

By Donald C. Moore

Asamera Minerals Cannan Mine has been producing a 170 g gold/tonne (5 oz gold/ton) siliciaus flotation concentrate since July 1985. Flotation concentrate is shipped to a smelter for gold recovery. Numerous processes have been investigated to economically produce bullion on site. This paper describes the laboratory and pilot plant test results of a bacterial assisted oxidation of the refractory minerals. Economic comparisons with autoclaving and roasting processes are included.

Jan 1, 1989

By K. P. Stricker, H. Keddeinis, K. Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300° and 600°C (570° and 1,110°F) is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies, depending on structural homogeneity, porosity, and gangue quantity. Sinters with heterogeneous structures transmit stress to the hematite phase and this favors disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 2, 1984

By Michael Li

Unsaturated flow and solute transport were studied in three large columns measuring 1.5 m diameter x 2 m height, loaded with up to 3.7 t of oxidised waste rock, which was excavated from the Stratmat pile at Heath Steele Division, Noranda Inc. and contained elevated concentrations of zinc in the pore water. The bottom of each column was partitioned into 37 squares, each of which was drained independently. Following rain simulations at the top of the rock bed, the drainage in each drain port was monitored for volume and physicochemical parameters at pre-determined intervals. This paper describes some of the observations resulting from the experiments. The main conclusion of the study is that unsaturated flows in waste rock are heterogeneous, and flow channelling is ubiquitous. The results imply that the transport of solutes from oxidised waste rock to its toe drainage is subject to various controlling mechanisms, including geochemical equilibrium control and successive pore water dilution control.

Jan 1, 2000

By I. A. Costa, Y. Fouquet, F. Barriga

"Lucky Strike and Menez Gwen are two hydrothermally active sites located along the border of the Azorean plateau, southwest of the Azores islands where the alteration processes affecting basaltic rocks are prominent (Costa et al., 2003). Here we report on a slabby brecciated rock, abundant at both Lucky Strike and Menez Gwen, composed mainly of basaltic fragments cemented by hydrothermal precipitates from warm fluid circulation system. Research reveals that hydrothermal alteration takes place mainly by replacement processes, in which silicification is dominant (Costa et al., 1997 and Costa, 2014).Petrographic observations, including scanning electron microscopy (SEM), microprobe analysis, and mass balance studies made on basaltic fragments within the breccia show that silicification is one of the main processes resulting from hydrothermal fluid circulation. This alteration process leads to complete replacement by silica, in extreme cases, forming an impermeable cap that may contribute to the formation of sub-seafloor sulphide deposits, including examples in the geological past."

Sep 1, 2014

By G. C. Anderson

The Cleveland Cliffs NOLA electronics and software upgrade is a Windows based system that simultaneously controls two Texas Nuclear NOLAs and associated sampling. It uses new spectrum analysis and algorithms to produce accurate, linear silica measurement with slurries that range from 5 through 50 percent solids. This linearity allows us to achieve a reproducible procedural calibration. The hardware consists of readily available shelf items, is extremely redundant and eliminates all NIM bus modules.

Jan 1, 2003

By Z. A. Md-Nor

Risk management is an established loss-control methodology that has been applied successfully in many industries. Recently, interest in this structured approach has grown in the mining industry. The main objective of this research was to develop a risk-assessment process, which is a part of risk management, that can be used by the U.S. mining industry to more thoroughly characterize risks associated with haul truck-related fatalities. The assessment is based on historical data obtained from the U.S. Mine Safety and Health Administration (MSHA) investigation reports, which includes 113 fatal incidents that occurred from 1995 through 2006. The risk-assessment process used in this research involves the following basic steps: identification of the risks, risk analysis and risk evaluation. The preliminary hazard assessment (PHA) method is used in identifying and quantifying risks. Risk levels are then developed using a pre-established risk matrix that ranks them according to probability and severity. The resulting assigned risk value can then be used to prioritize control strategies. This paper is a part of a detailed study on risk assessment for equipment-related fatalities in mining sponsored by the Western U.S. Mining Safety and Health Training and Translation Center.

Jan 1, 2008

By R. I. Yano

Analyses of trace elements in bulk ores and in chalcopyrite and other ore minerals from porphyry copper systems worldwide, including skarns and breccia pipes, reveal some key factors regarding byproduct critical elements. Petrographic and scanning electron microscope analyses combined with a laser ablation inductively coupled plasma mass spectrometry technique developed by the USGS on selected ores from the Mackay-Stanford Ore Deposits Collection suggest that selenium occurs as atomic substitutions in sulfides, particularly pyrrhotite (up to 430 ppm) and chalcopyrite (up to 300 ppm Se); tellurium occurs predominantly as less-than-five-micron-sized inclusions of bismuth-tellurium minerals in other ore minerals, particularly chalcopyrite; cobalt and nickel are locally enriched in pyrite (up to 7800 ppm Co and 9100 ppm Ni); gallium is locally enriched in magnetite (up to 83 ppm Ga); indium and silver are locally enriched in chalcopyrite (up to 890 ppm In and 770 ppm Ag); cadmium substitutes for zinc, particularly in sphalerite (up to 4100 ppm Cd). There is considerable variation, both between and within individual deposits, in both selenium and tellurium content in these copper ores, ranging from 0.6 to 148 ppm Se and 0.09 to 64 ppm Te. Indium tends to be high in copper ores that are also enriched in silver. At current prices, many of these elements are sufficiently enriched to warrant investigation into metallurgical recovery as byproducts of the major elements.

Feb 27, 2013

By Klaus Böde

Within the national and international strategy of the German based construction company HOCHTIEF, the majority of its business units is equipped with the comprehensive software package ARISTOTELES. This software is a powerful business information system for all accounting and controlling related processes in medium-sized and large construction and other related companies. Due to the complexity of the software, time constraints, and limited financial resources an implementation of this software package requires thorough project management. In this paper the relevant elements of project management are outlined based on practical experiences gained during this international IT - implementation project. Special emphasis is directed to the identification and management of potential risks. In this case particular acknowledgement was given to the multinational nature of the project and modernization of the business. This includes thorough reorganization of the company, significant changes of job requirements, and substantial trainings for its employees. At the same time key success factors like knowledge transfer, adoption of Czech legal requirements, commitment of management, networked thinking, and integrated project planning come into play. The costs for implementation had to be carefully evaluated because the software was implemented in a country with a considerably low cost I price level. All these impacts to the business had to be managed within the scope of transformation of business and political environment from socialist to market driven economy.

Jan 1, 2002

By G. G. O. O. Uwadiale, M. A. Kollere, M. A. U. Nwoke

Birnin Gwari and Alawa graphite deposits were upgraded by flotation. Using 0.5 kg/t kerosene and 0.25 kg/t sodium silicate, flotation concentrates grading 90.7% and 88% Cg with recoveries of 86.2% and 84% were produced from Birnin Gwari and Alawa graphite samples, respectively. The combination of 0.5 kg/t kerosene, 0.2 kg/t pine oil and 0.25 kg/t sodium silicate yielded high-grade graphite (92.3% Cg) with a recovery of 83.9%. Flotation with refined rubber nut oil and kerosene, at a 1:1 ratio, produced a concentrate grade of 86.3% Cg with a recovery of 90.4%. With acid leaching of the flotation concentrate, a high-grade graphite concentrate containing 98% Cg was produced.

Jan 1, 1998