Search Documents

By Thomas H. Holley

This presentation will describe the underground excavation at the Bad Creek Pump Storage project. It consists of approximately 3,650 m of various size tunnels ranging from 4.2 m to 9.0 m finished diameter, a powerhouse cavern 45 m high by 135 m long by 22.5 m wide, and 422 m of 9 m diameter shaft. A total of 350,000 m of rock will be excavated, hauled, and placed in a submerged wier. Temporary rock support consisting of shotcrete and/or rockbolts is installed as required.

Jan 1, 1987

By Richard V. Good, John B. Harvey, Lloyd S. Jones

INTRODUCTION The term "Rapid Underground Excavation" is generally associated with high speed tunnel advance with large volumes of excavation, and indeed this is the type of work for which most of the recent innovations in methods and new machinery have been developed. However, the term applies as well to any underground excavation process that results in an earlier project completion than would be expected with conventional methods, and hopefully with a decrease in total unit excavation cost. Often significant progress has been made during the primary stages of an underground construction project and then an inordinate amount of time and effort has been expended on small units of "miscellaneous" excavation which has delayed the overall project completion and escallated overall unit costs. Construction at the Nevada Test Site of the Atomic Energy Commission for underground testing frequently requires significant amounts of so called "miscellaneous mining" such as short access drifts, cross cuts, alcoves, niches and concrete keyways. Many of the keyways must be excavated without disturbing the rock beyond the excavation lines and construction scheduling often dictates that much of the work must be accomplished without disturbing sensitive electronic equipment already installed. In order to cut down on lengthy and costly delays required for the tedious manual excavation of much of this miscellaneous mining, a market search was made for suitable mechanical excavation equip-

Jan 1, 1997

By Pierre Mousset-Jones

I wish to submit this discussion item on an article published in the August issue of MINING ENGINEERING by Wala and Altman on the use of canonical diagrams for mine ventilation networks. The advent of computer graphics and plotting has enabled complex underground mine layouts to be displayed and plotted in a variety of three-dimensional formats that very closely represent the actual mine layout. This enables the ventilation engineer, who is familiar with the mine, to display the network pressures, quantities, resistances, and fan locations in a way that can be understood by everyone working at the mine. This is important if the ventilation engineer needs to discuss changes in ventilation with production personnel, or escapeway procedures with union personnel. While I can see some of the potential advantages in the canonical ventilation network diagram described by Dr. Wala, it appears to me that the fact that the diagram has no visual equivalence with the actual mine layout means that most mine personnel will find such a diagram almost incomprehensible. The authors have alluded to certain advantages with the canonical diagram. However, I find it difficult to see that these outweigh the fact that almost everything listed can be duplicated in isometric diagrams, and in a manner that is easily understandable to everyone in the mine from the miner to the mine manager. Perhaps the authors could show a clear example comparing an isometric with a canonical portrayal of a mine network showing the information that is immediately available from the canonical network that is not obvious in the isometric diagram. There is in this country a severe problem with the need for ventilation engineering and expertise to be used and accepted by mine management as a necessary part of mine planning. It seems to me that to introduce the requirement for further explanation so that management can understand a canonical network display will hinder more than help the recognition that ventilation engineering needs at so many mines in this country. However, I can see that the canonical approach does have its place in assisting the practicing mine ventilation engineer, wherever he or she exists in the organization chart for a typical mine. In this case, could the authors please indicate the availability of the computer program to compute and plot the canonical diagram for a mine ventilation network.

Jan 1, 1989

By J. E. Kulas

Red Dog is a Mississippian to Permian aged sulfide deposit located in the western Brooks Range north of Kotzebue, Alaska. It belongs in the family of black Shale hosted sedimentary exhalite deposits but lacks classic sulfide sedimentary textures. Pervasive silicification, and a significant portion of the mineralization, is replacement in nature. An extensive feeder vein system cuts the footwall and the exhalite package. A Jurassic to cretaceous age compressional event has repeated the ore section through thrust faulting and folding. The orebody contains 77,000,000 metric tons averaging 17.1% Zn, 5.0% Pb and 82 g per metric ton of Ag. Weathering has locally altered the sulfides to sulfates and formed elemental sulfur.

Jan 1, 1992

By David E. Thompson, Edward S. Plotkin

The Massachusetts Bay Transportation Authority (MBTA) Red Line Extension Northwest is nearing the final stages of construction. The 3. 1 mile extension of the Red Line from the existing Harvard Square Station in Cambridge, Massachusetts to Alewife Brook Parkway in Cambridge, includes a large, near surface, hard rock, rapid transit chamber at Porter Square in Cambridge (Figure 1).

Jan 1, 1983

By Peter Shuttleworth, Chris Fesq, Eddie Woods

Precast concrete segmental linings for tunnels have traditionally been designed with conventional steel bar reinforcement. In many cases, this has been satisfactory in service, but in others, major problems have occurred with the durability of the linings. Commonly this has resulted from corrosion of the reinforcement, mainly from chloridesin ground water, causing spalling of the concrete and leading to very expensive and disruptive repair programs. This paper discusses the relative merits of designing tunnel linings with steel fiber reinforcement to provide long-term durability, improved impact resistance and toughness for greater load capacity across joints, enhanced robustness during transportation and erection, plus improved fire resistance with the addition of polypropylene fibers. Guidance is also given in the selection of the correct fiber type, mix design and testing methods to establish the optimum dosage required and production techniques to ensure even distribution and compaction.

Jan 1, 2005

By J. R. Walls

Mining is one of world's oldest industries. Its rich history continues into modern times. The Waste Isolation Pilot Plant (WIPP) located in southeastern New Mexico is writing the next chapter in mining history. In fact, WIPP technology is the key to closure of the nuclear cycle with the disposal of nuclear waste in a deep geological repository. It might seem odd that the age-old institution of mining would be linked to the problem of nuclear waste disposal. In fact, the nuclear industry would not exist without mining. Uranium ore is mined from either underground or surface mines as the initial step in harnessing the magnificent resource of nuclear energy.

Jan 1, 1996

By Leslie S. Rubin, John C. Roberge, Mackenzie Burnett

A self regulating helical inducer has been developed and tested for dry injection of coarse or fine solids into a hydraulic pipeline. This centrifugal pumping device has also been modified and tested for use as a boost pump in medium and long distance pipeline haulage systems. The helical inducer has been operated as an integral component of a slurry injection vehicle. This compact, low profile vehicle also includes crushing and screening components, solids feeding components, a track drive system for mobility and is run by a single operator. The helical injector and boost pump operate without speed and flow controls allowing for the practical hydraulic transport of excavated materials.

Jan 1, 1983

By Christof Metzger

This paper discusses the process utilized by the Kiewit?Bilfiger Berger Joint Venture (Contractor) to select, design, and procure the largest mixshield tunnel boring machine (TBM) ever implemented in North America. The mixshield will excavate the 8,534 linear m × 6.7 m ID (28,000 linear ft × 22 ft ID) tunnel for the City of Portland Oregon?s, Bureau of Environmental Services (Owner) East Side CSO Tunnel Project. TBM selection was conducted under a preconstruction contract in which the Contractor, Owner, Construction Management Consultant and Designer collaborated on TBM selection prior to commencement of construction. This paper focuses on TBM design considerations, including the use of one versus two machines, machine configuration,extended-wear protection, hyperbaric interventions, boulder digestion, and erection of a steel-fiber-reinforced segmental lining

By R. J. Pugh

The coagulation of dispersions of weakly magnetic oxide mineral ultrafines (such as natural hematite or chromite) in an external magnetic field can be described from inter-particle forces. Essentially, coagulation occurs when the short range London-van der Waals interactions and the long range magnetic forces outweigh the stabilizing electrical double layer repulsion. From the classical colloid chemistry theory, we have calculated the various components of the potential energy for different sized particles at a series of ionic strengths and magnetic field intensities. We have related this theoretical analysis to experimental studies where the magnetic field-induced coagulation of ultrafines of natural hematite and chromite in aqueous suspensions was investigated using a laboratory scale electromagnetic solenoid. The experimental results relate the coagulation process (as determined by magneto-sedimentation analysis) to the particle size, the slurry pH and the external magnetic field. In the magnetic fields, maximum coagulation occurred near the pH of zero point of charge (pHzpc) of the minerals (where the electrostatic double layer repulsion was reduced to a minimum) enabling the particles to enter the "primary minimum" energy sink. On the other hand, in cases where the electrostatic repulsion was not suppressed, then the long range magnetic forces enabled coagulation to occur in the "secondary minimum". This caused the formation of chains which appeared to be relatively stable during sedimentation.

Jan 1, 1993

By G. Newman, C. D. Sellars, E. A. Portfors

Power for mine operation in remote locations is usually provided by diesel generators. For gold mines where processing is normally desirable on-site, power requirements can be significant and the operating cost for diesel generation then becomes an important factor in mine feasibility. If a suitable site is available, a small hydroelectric power facility near the minesite can provide a significant portion of the mine power requirements. The hydrological, engineering and economic factors involved in small hydroelectric power development are described in this paper. Capital costs are minimized by run-of-river hydro development which does not require a dam and reservoir and has less environmental impact. During periods of low flow, diesel generators are used to make up the power demand. The hydrologic analysis required to determine unit energy costs is described and technical requirements for linking the hydroelectric power facility with diesel generation are outlined. Case studies are presented demonstrating the economic advantages of a small hydro installation. One case study is for a proposed gold mine in British Columbia and the second is a large operating gold mine overseas, for which the hydroelectric power scheme is presently under construction .

Jan 1, 1987

It took me nearly nine months to make the move from Arizona to Berkeley, opening an office and planning our new home. While I was in Warren Dorothy had rented two rooms for my office In the new California Commercial Union Building at 315 Montgomery Street in San Francisco. She made such a good choice that this remained my address for more than 50 years Dorothy had also looked over many lots In Berkeley, and took an option on the one that pleased her the most. It was a beautiful lot, or rather three, as we took three lots to protect our view. The only possible drawback was that it was in a new district and there were only two houses within two blocks. No one could tell how the area would develop but we liked it so much that we bought the lots on the spot and signed a note to guarantee payment. Dorothy's good judgment was shown by the fact that after 50 years we are still glad to be living on the same property, at 168 Southampton Avenue. We arranged a meeting with the distinguished architect Bernard Maybeck-and employed him to design a house for us. Dorothy spent most of her time with Maybeck planning the house and an attached studio for her, and she later wrote an amusing essay on her dealings with Maybeck. They were so successful that even now we could not think of any changes we would have wanted. It took several months to design a house that suited Dorothy and would fit on our hilltop. I was glad to overcome some of Maybeck's scorn for "only an engineer" by showing how, by rotating the studio addition 45º, it would fit the lot without serious excavation. We finally signed a contract with Maybeck, borrowing so much money that it scared us. First Consulting After short jumps to the gold mines in the Secret Pass District near Kingman, Ariz., and to the Espiritu Santo prospect adjoining the rich

Jan 1, 1976

By C. E. Capes

INTRODUCTION In the coal industry, ever greater amounts of fine coal must be processed due to the need to crush to finer sizes for impurity liberation in low cost physical cleaning processes. Fine coal processing is a major problem for the industry, both through the cost of disposal of reject fines and through the mining cost of lost coal values. Of the available disposal methods, impoundment has always been the most popular. In many cases, when the coal fines were of sufficient quality, froth flotation and expensive filtration methods were used to recover the coal in these waste streams. The coal fines are not always of a marketable quality, however, and flotation, due to poor yields and difficult dewatering, has always been an expensive and not necessarily profitable process. The oil agglomeration method is increasingly important as a technology for the treatment of fine coal-in-water suspensions. These fines can be preferentially wetted and agglomerated by many different oils mixed with the suspensions. Ash-forming impurities remain in suspension and are rejected when the agglomerates are recovered, for example, by screening. Agglomeration-based methods provide perhaps the only practical means for upgrading extremely fine coal to useful products on a large scale. As with froth flotation, oil agglomeration relies on differences in the surface properties of coal and impurities to effect separation. Whereas flotation be- comes less effective with particles finer than 200 mesh (0.075 mm) or coarser than 50 mesh (0.3 mm), there appears to be no lower limit on particle size for oil agglomeration while particles % in. (3.175 mm) diameter or larger can also be treated, if desirable. In addition to this ability to clean a broader size range of coal particles, oil agglomeration can produce a dense, coarse granular product of acceptable strength and low water content without the need for vacuum or thermal drying. The preferential wetting of solid surfaces by immiscible liquids has been utilized, if not fully understood, for a long time. Indeed Gaudin,229 in tracing the ancestry of froth flotation, refers to a 15th century oil-pulp kneading procedure in which water-wetted particles were freed under water from an oiled mass. An understanding of the physical chemistry involved in such

Jan 1, 1991

By William Cass, Ellen Caftel Turcotte

The Elliot Lake Centre was established in 1965 as an independent Centre for Continuing Education offering a variety of adult education services. In 1976 all retraining and community college type activities were transferred to the Sault College of Applied Arts and Technology which had opened a branch campus in Elliot Lake. Upon the completion of this transfer, the Elliot Lake Centre was then contracted in 1977 by the Canada Centre for Mineral and Energy Technology to study the feasibility of establishing a research and information institute dealing with various health and safety concerns of the uranium worker. By late 1980, a federal charter was granted for the establishment of the Canadian Institute for Radiation Safety, made possible through the cooperative efforts of the Governments of Canada and Ontario, the Ontario uranium mining and refining companies, and the Elliot Lake Centre. On 1 April 1981 the Institute officially began operations. PROGRAM DEVELOPMENT AND COORDINATION In May 1978 the Elliot Lake Centre initiated a voluntary sputum cytology program for uranium workers. This program was financed by the Ontario uranium mining companies: Agnew Lake Mines Limited near Sudbury; Madawaska Mines Limited in Bancroft, and Denison Mines Limited and Rio Algom Limited in Elliot Lake. In 1981 additional funding was granted by Eldorado Nuclear Limited for a small group of employees at the company's uranium refinery in Port Hope, Ontario. Initially in 1978, program participants were accepted according to length of employment, radiation exposure levels (calculated in working level months) and/or smoking history. These restrictions were abolished within a few months and all uranium workers were encouraged to participate. From 1978 to 1979 the sputum cytology program was medically directed by personnel from the Montreal Cancer Institute. Until 1979 all data maintenance for the program was performed manually, however the effort required to sustain the system increased significantly as the number of participants grew. In September 1979 the Division of Thoracic Surgery at the Toronto General Hospital, under the direction of Dr. F.G. Pearson, submitted a proposal to the Elliot Lake Centre to develop a data processing system to help coordinate the surveillance program. In October 1979, Dr. Pearson became the new Project Director. Director of the Cytology Program is Dr. D.W. Thompson of the University of Toronto who is responsible for all cytologic analyses. Developmental work to establish the new surveillance system was initiated in January 1980 and became fully operational at the beginning of March 1981. The following sections describe the Elliot Lake operations of the sputum cytology program now conducted by the Canadian Institute for Radiation Safety. PROGRAM PARTICIPATION As of 1 September 1981 the sputum cytology program has 518 participants enrolled. Eligibility is restricted only to a willingness to participate and the ability of an individual to produce adequate sputum samples. Each participant registers for the program at the Institute and is given personal instruction on methods of sputum collection. The majority of the participants in this program are employed by the uranium mining industry; some work for firms which are contracted by the larger companies. Many participants are either retired from the work force or receive disability pensions or workmen's compensation benefits. Other participants have been employed in the uranium mining industry and have since gone on to other employment; some work for various federal and provincial governmental agencies concerned with the mining industry. Some participants are referred to the program by their family physicians because of smoking histories and/or various respiratory conditions. A small number of these individuals have never been involved in the mining industry at all. A chart describing program participation by employment is found in Appendix 1. PROGRAM REGISTRATION In the Elliot Lake area, persons interested in registering in the program are required to go directly to the Sputum Cytology office located at the Canadian Institute for Radiation Safety. Each individual is interviewed personally by the Program Officer. For the employees of Agnew Lake Mines, Madawaska Mines and the Port Hope refinery of Eldorado Nuclear Limited, registration is possible during the Program Officer's semi-annual on-sitevisits. Participants are assigned, in chronological order, "program numbers" for easier identification. File labels are color-coded according to place of residence or, in some instances, place of employment. Each file is stamped with the date each sample bottle is distributed. A file contains: all original test results, a completed registration

Jan 1, 1981

By U. Paschedag

Today's modern longwalls have to produce high outputs with maximum availability and running time with the additional requirement of ever increasing panel width and length high-performance face conveyors require intelligent solutions for the integration of drive systems and chain tensioning devices into the overall longwall automation. The fully automated chain tensioning system allows the operation of an AFC with optimum chain tension at all times regardless of actual load on the conveyor. For the heavy-load start-up, the accurate load-sharing and an efficient overload protection of modern AFC's WESTFALIA and Dodge jointly developed the integrated WB/CST drive system.

Jan 1, 1995

By P. Mousset-Jones, F. Calizaya

Ultrasonic anemometry is a relatively new method of measuring the air velocity in underground excavations and is not widely used. The method has been mainly used for surface applications, such as meteorology and fluid flow measurement. Several instruments were looked at to determine their applicability for continuous underground monitoring systems. The units fall into two main categories: variable distance units and fined distance units. The method relies on the acceleration and deceleration of ultrasonic pulses transmitted through a moving airstream. This study presents some of the results of the testing of variable and fixed distance ultrasonic anemometers in a wind tunnel and a mine drift.

Jan 1, 1995

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By Frank J. Markewicz

The expanding: demand for ilmenite for use in the manufacture of titanium pigments, the knowledge that much of this raw material comes from distant points and therefore has to include a heavy freight charge in the price of the delivered product, and the further knowledge that ilmenite occurs both in the crystalline rocks of northern New Jersey and also in some of the Triassic igneous rocks, were considerations which led to a search for ilmenite-bearing sands in southern New Jersey. That this search was successful is now history, and it is the senior author's privilege to state here that most of the credit belongs to his associates who did all of the heavy work of hand-augering for samples, and who made all of the heavy-mineral separations. We all are grateful to members of the Department of Geology at Rutgers and Princeton Universities for the use of equipment which enabled us to evaluate certain samples from our ilmenite exploration program. In addition, we wish to express our appreciation to many companies for their cooperation and for their permission to publish mineral and chemical analyses. We also acknowledge with much appreciation our debt to the geologists and engineers with whom we have had many lively and rewarding discussions relative to the ilmenite deposits.

Jan 1, 1958

By Bob Miller

"All industries have parts and equipment that are exposed to some type of destructive wear. Hardfacing is a cost-effective tool that will minimize wear and increase service life. At first glance, hardfacing can be confusing and troublesome. In reality, it is not.Postle Industries, a manufacturer of hardfacing products, has found that the 22 answers to frequently asked questions may help operators select hardfacing products that are most appropriate for their application. The first 10 questions are addressed in these pages, the full list can seen at Mining Engineering online under the Web-Only Content section.1. What is hardfacing?Metal parts often fail their intended use not because they fracture, but because they wear by abrasion, impact, metal-to-metal contact or some other form of wear, which causes the parts to lose dimension and functionality. Hardfacing, also known as hard surfacing, is the application of a buildup or wear-resistant weld metal onto a part’s surface by means of welding to extend the life of the part. The weld metal may be applied as a solid surface or in a pattern, such as a waffle pattern, herringbone or dot pattern, etc.Hardfacing is becoming increasingly important for many industries to protect equipment that is exposed to wear and abrasion including parts used in mining, earthmoving and construction, oil and gas drilling and steel making and forging. Extending the life of wear parts can save thousands of dollars and improve productivity. Hardfacing can be used to recondition parts that have already been exposed to wear and have lost their useful life, or used in the manufacture of new parts to improve their life before they are put into service.There are three main types of hardfacing applications:• Build-up or rebuilding.• Hardfacing or overlay.• A combination of build-up and overlay.2. What base metals can be hardfaced?Carbon and low-alloy steels with carbon contents of less than 1 percent can be hardfaced. Medium carbon and low-alloy steels are very common since they provide higher strength than mild steels and better abrasion resistance. High carbon alloys may require a special buffer layer.The following base metals can be hardfaced:• Stainless steels.• Manganese steels.• Carbon and alloy steels.• Cast irons.• Nickel-base alloys.• Copper-base alloys."

Aug 1, 2016

By Gennaro G. Ph. D Marino

In order to improve handling of subsidence damages the Illinois Mine Subsidence Insurance Fund supported the development of novel cost-effective methods of repair. The research in developing the repairs was directed towards the most common and costly damages that had been observed. As a result repair techniques were designed for structurally cracked foundations in the tension zone; structurally cracked foundations in the compression zone; and damaged or undamaged tilted foundations. When appropriate, the postulated methods would result in: 1. significant cost savings (over conventional procedures); 2. a structural capacity greater than when the foundation was untracked; and 3. an aesthetic appeal. All the postulated repair methodologies were laboratory and/or field tested. The paper will summarize the essentials of each technique developed and the test results.

Jan 1, 1986