Search Documents

By H. Akbari

The ordinary Portland cement (OPC) is the key pozzalonic component of the concrete mix, widely used as the construction material world-wide. Billions of tons of OPC are used in the construction industry each year. However, calcinations of limestone and silica that produce OPC also produce almost an equal amount of CO2 during the cement manufacturing process. Thus, OPC production accounts for nearly 7% of all anthropogenic CO2 emission each year. The main objective of this study was to develop a geopolymer-based composite to be used as a substitute for OPC in concrete application to significantly lower the carbon foot print of the construction industry. A waste material produced during the coal combustion process was used as the main raw material for the geopolymer-based composite. It was mostly the non-metallic content of the F-type fly ash produced from the combustion of bituminous coal. The authors envisioned to extract some of the valuable metal oxides from fly ash prior to using the major non-metallic portion of the fly ash for geopolymer concrete application. The results obtained from this study exhibited that the compressive strength of the geopolymer concrete compares favorably with that of the conventional concrete prepared using the OPC.

Feb 27, 2013

By Ian J. Duckworth, Pierre F. X. Mousset-Jones

A detailed heat flow project was conducted at the Homestake Mine in Lead, South Dakota. This paper presents results obtained from a stope sensor system installed in the mine. The design and installation of the system are described in detail in a previous paper (Duckworth et al., 1992). The major project objective was the construction of a comprehensive heat flow data base to allow the design and testing of a new climate prediction model applicable to irregularly shaped underground excavations in non-homogeneous surrounding rock types. A mechanized cut-and-fill (MCF) stope contributes a substantial overall heat source in a mine, and the effect of this source on the working environment must be considered when planning future ventilation and refrigeration requirements. The relative magnitudes of the component heat sources encountered with the MCF mining technique are presented, having been computed from actual stope beat flow data collected over a one-month study period. The percentage of the overall heat load that is removed from the scope for each component heat sink is evaluated, and the overall energy balance is analyzed. A one-month study length was considered a sufficient period of time to allow stope monitoring for a complete range of mining conditions.

Jan 1, 1993

By W. Gibson Jaworek

Of increasing importance to the student of fuels economics has been the extent to which different primary energy sources can substitute for each other in the various energy markets of the nation. Knowledge of the nature and extent of fuel interchangeability can aid the fuels economist in projecting trends of energy utilization, as well as giving him a better understanding of the past and present conditions of fuel markets. It is also important to the consumer to know just how much flexibility he can maintain in his energy consuming operations. And, finally, various governmental bodies show keen interest in the degree of energy substitutability in determining public policies concerning the fuels industries. The presence of excess fuel production capacity in the United States during the early 1960's indicates that fuel interchangeability should become more prevalent in the increasingly competitive energy markets of the nation. Discussion of fuel intercompetition is almost always restricted to qualitative terms-because of the lack of comparable statistical data, between the different energy sources in geographic or "type-of-use" fuel, markets. There are exceptions, of course, such as, the excellent fuel consumption data which are available on steam electric generating plants throughout the nation. In other sectors, statistics are at best incomplete.' Inmost instances, indirect fuel consumption indicators, such as sales of fuel burning equipment, are extensively used to measure market shares of a particular fuel; however, these indicators are hard to evaluate precisely without prior knowledge of the total competitive market.

Jan 1, 1961

Resolution Copper Mining LLC (RCML) is currently in a Pre-feasibility study evaluating a large and deep copper and molybdenum deposit in the historic mining district east of Superior, Arizona. Work scheduled for the next several years includes dewatering the existing shut-down mine (the Magma Mine) and sinking an exploratory shaft to 2,130 meters (7,000 feet) below the surface. To dewater the Magma Mine and sink the exploratory shaft, RCML must extract and manage about 2 billion gallons of accumulated mine water inventory, as well as about 300 million gallons per year of new inflow. In order to conserve a valuable water resource in a desert environment, RCML worked with the New Magma Irrigation and Drainage District (NMIDD) to provide treated mine water to blend with and supplement the NMIDD?s water supply to approximately 2,000 hectares (5,000 acres) of farmland located east of Phoenix. A 44 km (27-mile) pipeline was needed to convey the treated water. It was essential that a treatment system be used which could reliably meet irrigation water quality goals, produce a non-scaling effluent to maintain pipeline flow capacity, and generate a dense sludge minimizing disposal cost and volume. This paper describes the resulting mine water treatment and recovery system (MWTS) and how the system has performed against objectives.

Jan 1, 2011

By R. Perlo

"INTRODUCTION Peoples’ and operators’ safety in construction are tightly linked to the engineering choices, as much as the necessity of reducing time and costs of realization. Therefore, it is of paramount importance to address them properly from the earliest stage of the design, identifying the risks connected to the work and the variability of such during the different phases of the project. Risk is often measured as the expected value of an undesirable outcome. Regarding to occupational safety and health, the risk is the likelihood that a person may be harmed of suffers adverse health effects if exposed to a hazard. This combines the probabilities of various possible events and the assessment of the corresponding harm into a single value. However, the actual occurrences are often more complex than a single binary possibility case. In a real case scenario, with several possible accidents, the total risk is the sum of the risks for each different accident, provided that the outcomes are comparable. The semi-automatic tunnel support system along with its erector machine proved to be a solution with improved structural performance, able to reduce the time and yet to deliver an enhanced, quality-aware and safer working environment for the operators. The implementation of the system provides the engineers, the contractors and the owners with an effective alternative option shortlisted in 2015 for the ITA Award for the Safety Innovation of the Year. In a market industry driven by safety and time constrains the efficiency shall be the ultimate goal, in order to provide solutions able to negotiate with the most challenging ground conditions. In this paper, the authors describe the recent developments on regard of this whole new tunnel support system, including design approach and presenting related case histories OFFSETTING THE RISKS Considering the above factors, from the manufacturers’ point of view, an effective way to limit the construction risks is to focus on the material and technological characteristics, their application and the risks related to them including any residual risks. Finally addressing the construction needs also involves time and cost-effective solutions. The path to follow is an integrated approach where the efficient management of the risk is supported by a flexible, user-friendly, and time effective product that is able to provide a safe, reliable and viable solution to address the construction requirements. Therefore, in a market sector driven by safety and time constraints, the efficiency is a key goal, in order to avoid redundancy and yet to deliver a safe working environment able to meet the construction schedule. The safety of all the parties involved is given by stable working conditions, either for the workers, or the operators and eventually the public. Therefore, the solutions provided should ‘strengthen’ the overall condition and such “to limit or to reduce the deformations within acceptable designed limits and to prevent [the tunnel] to collapse” [1: Clause 207.1.4]."

Jan 1, 2018

By William A. Wallace

Common mineral resources (sand, gravel, crushed stone, etc.), which are so necessary for the construction of metropolitan areas, are rapidly being depleted or otherwise rendered unavailable in the very areas that need them most. However, the problem of planning for these resources involves a number of independent and dependent variables that must first be defined and related. Finally, a dollar value must be assigned where possible. Complex interrelationships between the variables and their dependence on outside factors has made mathematical "solution" of the problem of planning for non-renewable mineral resources difficult at the present time. Therefore, the use of computer simulation is suggested as a means by which this complex problem can be investigated. The purpose of this paper is to report on a continuing research program whose objectives are: (1) to delineate the factors involved in planning for the utilization of common mineral resources in urban-suburban environs; (2) to construct a planning model for these materials amenable to computer analysis, (3) evaluate the model by using test cases, and (4) perform a sensitivity analysis to determine the initial parameters in future planning for these materials.

Jan 1, 1968

By D. E. Poole

Injury Prevention: Dependent, Independent and Interdependent In recent years, management-directed (dependent)safety programs have lost ground to the more successful self-directed (independent) programs, where employees take responsibility for their own safety. Today, with the growth of the team concept in industry, a mutual-caring (interdependent) approach to workplace safety is gaining wide acceptance. This presentation compares characteristics and results of the three progressive levels of safety responsibility and explains how to develop a successful interdependent program. The presentation will also detail the common principals that are necessary for safety excellence under any of the management styles.

Jan 1, 2000

By W. M. Hart

The current Automatic Data Acquisition system developed by some support manufacturers makes it possible to continuously monitor and record changes in leg pressure and advancing ram stroke in every shield, and shearer position at any moment during the mining operation. In order to effectively use the massive data obtained from this system for improving production and maintenance managements as well as providing better roof control at a longwall face, the research currently conducted jointly by West Virginia University and Cyprus-Amax Coal Co. attempts to develop a Longwall Management System for mine operators. The LMS software package runs on a MS Windows NT environment and consists of four sub-systems: (1) Data Interpretation and Analysis; (2) Production Management; (3) Maintenance Management; and (4) Ground Control. This paper presents the details of each sub-system.

Jan 1, 1995

By J. Weyer

"Colored gemstones are most often mined in small scale artisanal mining operations. Sri Lanka is well known as source for precious stones since thousands of years. Gemstones are mine in small open pits, directly in rivers (river dredging) and in underground mines. Almost all mined deposits are alluvial deposits. PRECIOUS STONES AND DEPOSITS Precious stones from Sri Lanka are well known for thousands of years. Tales and legends from Arabia, India, China and reports from discoverers like Marco Polo describe the fabulous stones from Ceylon which was the name for Sri Lanka before 1972. Already 1000 BC King Salomon got valuable gemstones from the legendary Queen of Sheba on her visit to Jerusalem. Paintings (frescoes) of the “cloud maidens” with huge gemstones can be seen at the “mirror walls” of the Sigiriya rock fortress - one of the eight World Heritages Sites of Sri Lanka.And even today some of the most valuable and most desired gemstones come from Sri Lanka. The term “Ceylon Sapphire” stands for an excellent royal blue color of high quality corundum from Sri Lanka. Reason enough to look a bit closer how these gemstones are mined. Sri Lanka has rich gemstone deposits which are mined underground, in small open pits or directly within a river. Some of the primary deposits in magmatic and metamorphic rock are also known, but most gemstones are mined in secondary alluvial deposits. Gem bearing deposits can be found in a band from NW to SE. Highly probable deposits and main mining areas can be found around Ratnapura – the city of gems, down to the coast (Matale) and up to the region around Elahera. These secondary deposits are mostly thin layers of gravel and sand, so called “illam”. The depth can vary between some dm to 10 25 m or even almost 40 m. But the average depth is about 12 m. Gemstone mining is controlled, licensed and regulated by a special authority – the National Gem and Jewelry Authority - which was founded in 1993. Another task of this authority is the promotion and development of the gemstone industry and the control of import and export of gemstones. Any violence of the NGJA law can lead to a fine or even up to 5 years imprisonment. To increase the confidence in the gemstone industry the Authority offers a unique service to foreigners. All bought gemstones can be tested free of charge in certain laboratories in Ratnapura and Colombo. So visitors can be sure they got no imitations, wrong stones or even synthetic stones or glass. It was said that detected synthetic stones will be destroyed and the seller will do all he can to replace the stone with the right stone. Otherwise he will lose his license."

Jan 1, 2016

By G. R. Laurer, J. W. Neton, C. Pomroy, N. Cohen, M. Eisenbud

INTRODUCTION In uranium miners, a causal relationship between exposure of the lung to high levels of alpha radiation and the consequential induction of bronchial carcinoma is now well-established (Wagoner, et al., 1965). Quantitation of this cause-effect association presents considerable difficulty, however, as the result of various confounding factors such as the contributing effects of smoking and/or arsenic exposure (Archer, Gillam, and Wagoner, 1976), normal metabolic variability and, perhaps most important of all, the absence of accurate radon/radon daughter exposure data. Estimates of cumulative lung exposures suffer from inaccuracy due to critical factors such as 1) unknown ventilation rates; 2) difficulties in obtaining representative mine air samples; 3) the variable character and magnitudes of the exposure sources; and 4) specific differences in metabolism and job histories that exist among miners. It was with considerable enthusiasm, therefore, that investigators readily embraced the idea of using skeletal burdens of the relatively longlived descendants of radon and its short-lived daughters, i.e., 210 Pb and 210Po (Archer, et al., 1968), to provide a measure of cumulative past exposure wherein the body acts as an integrating dosimeter. Early studies considered excretion rates of 210Pb and 210Po in urine, blood and hair (Sultzer and Hursh, 1954; Black, et al., 1968; Jaworowski, 1965; Bell and Gilliland, 1964) as well as their concentrations in bone samples, if and when they became available (Blanchard, Archer, and Saccomanno, 1969). These methods were ultimately complemented by in vivo, whole-body counting techniques using low background, NaI-Csl(T1) detectors (Eisenbud, et al., 1969). By this latter method, it would be possible to measure the skeletal burden of 210Pb directly, thereby avoiding the many difficulties associated with the relation between nuclide excretion rates and body burden. The rationale was simple; by knowing the skeletal burden of 210Pb it should be possible, by the judicious use of an applicable metabolic model, to estimate the cumulative lung exposure to alpha-emitting radon daughters (Fig. 1). Various models that were consequently constructed, however (Fisher, 1969), all suffered from the same limitation, i.e., the assumption that the source of 210 Pb in the skeleton and the source of lung exposure to the short-lived radon daughters were simply related and, if not, were at [ ] least not too variable (Raabe, 1970). By now, the difficulty with this assumption has been recognized and more sophisticated modeling techniques have been attempted which presumably present a more realistic picture of exposure conditions (Holtzman and Rundo, 1981). There is, nevertheless, the pessimistic view that due to the variety and variability (in time as well as in character) of sources that may exist for the origin of 210Pb in bone, it may [never] be possible to estimate past lung exposures accurately by an indirect, predictive model. For example, the origin of 210 Pb in the skeleton may include such sources as: 1) the decay of short-lived 222Rn daughters, inhaled and ingested; 2) the decay of 222Rn dissolved in body fluids and tissues; 3) directly from 210 Pb present in air, inhaled and ingested; and 4) 210Pb from non-occupational sources, e.g., food, water, smoking and endogenous 226Ra. The contribution of each of these sources may vary depending upon specific site conditions such as ventilation and mining operation. On the other hand, empirical evidence seems to indicate a trend reflecting the simplest of direct

Jan 1, 1981

By D. Craig Camp

conditions. The soils included 65 m of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2, 130 meters of soft clay, silt, and sand not exceeding 30standard penetration test SPT blows per 300 mm, and 220 m of rock ranging between an UCS of 400-600 kgf/cm2. The river crossing, utilizing 1778 mm OD x 19 mm wall x600 mm steel casing pipe without intermediate jacking stations, was part of a seven kilometer liquefied natural gas (LNG) transmission line in South Korea. This 440-m, 1,442-ft, river crossing was microtunneled through three different ground conditions and completed in just over three months. The crossing was achieved with an average of 25 m of ground cover and 15 m of water cover. The Kwang Yang River Crossing was part of a 7 km liquefied natural gas pipeline project for POSCO, a Korean steel producer. The microtunneling machine was custom built for this project. The microtunneling machine selected for this project was tooled with 7 button bits and 2 roller bits. None of the cutter bits were replaced during the drive. Inside the machine, before the spoils laden slurry was pump back to the surface, it would pass through an independent cone crusher. The crusher is placed in the slurry flow to make sure that none of the spoils are so large as to stop the return flow of the slurry. An additional requirement was for the inclusion of a compressed air lock. The air lock was required in the event that the cutter tools required replacement. The cutters were back loaded so that the workers would have access to change the cutters in the event of cutter failure or wear out. No intermediate jacking stations were installed for the drive. The soils included 65 meters of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2 with production averaging between 7 and 20 mm/minute. The second zone contained 130 meters of soft clay, silt, and sand not exceeding 30 standard penetration test (SPT) blows per 300 mm with production averaging between 80 and 180 mm/minute. The third zone contained 220 m of rock ranging between an UCS of 400-600 kgf/cm2 with production averaging between 7 and20 mm/minute. The steel casing pipe was 1778 mm OD x 19 mm wall x 6000 mm long. The project profile, see Figure 1, shows the soil conditions. The hand written numbers locate just above the pipeline are the production dates. The circled numbers are the 10 pipe joint increments. The project required 74 pieces of pipe to span the440 m drive. Figure 2 and Figure 3 are the jacking information. Figure 3 is a continuation of the information from Figure 2. The top section of the graph is the jacking force. The jacking

Jan 1, 2001

By J. A. Finch

The photographic measurement of bubble diameter is tedious and restricted to vessels with transparent walls and relatively low bubble concentrations. A new method for predicting bubble diameter in a flotation column has been developed and confirmed by comparison with measured mean bubble diameter (Yianatos et al., 1987) Flotation columns are not mechanically agitated. This note describes an extension of Ms method to a mechanically agitated flotation machine. A recent publication by Szatkowski (1987) provided sufficient data to calculate bubble diameter by the proposed method and compare with values determined photo- graphically. Method In a two-phase system (gas and liquid), bubble diameter (db), superficial gas rate (Vg) and liquid rate (Vl), and gas holdup (Eg) are linked by two relationships (see the nomenclature at the end of the paper for definitions of symbols). [ ] Equation 1 is the definition of slip velocity (relative gas to liquid velocity) for a countercurrent gas-liquid system, and equation 2 is an adaptation (Yianatos et al., 1987) of the expression of Masliyah (1979) for hindered settling in a multispecies system. The solution for bubble diameter is by repetitive substitution of estimates of db in equation 2 until the calculated Ubs is equal to the measured Ubs in equation 1. Results and discussion Table 1 presents the data obtained by Szatkowski (1987) from a mechanically agitated laboratory flotation machine. The machine generated bubbles by directing a gas stream into the vicinity of a disk rotating at Ngh speed (up to 8000 rpm) in the flotation slurry. The air was completely dispersed in a swarm of fine bubbles. A photographic technique was used to determine the distribution of bubble size. The mean diameter and standard deviation were then calculated. Table 1 provides all the information necessary for computing bubble diameter (Vl is assumed zero). The calculated bubble diameter is presented in Table 1 as d;. Figure 1 plots measured versus calculated bubble diameter and shows reasonable agreement between values. There is an apparent tendency to undercalculate the small bubbles and overcalculate the large ones.

Jan 1, 1987

By W. L. Josey

The Stibnite Project is an open pit/cyanide heap leach gold property located in the Yellow Pine mining district of central Idaho. The gold ore is in an oxidized zone of an epithermal deposit which is associated with a fault system related to Tertiary igneous activity of the region. The faults transect a roof pendant of metamorphosed sediments within crystalline rocks of the Idaho Batholith. Seasonal mining is at a rate of 3900 mt/d (4300 st/d) of ore with a 2:l waste to ore ratio. Gold and silver are recovered through a process of cyanidation, carbon adsorption and desorption, and electrowinning. Disposal of the leached ore requires chlorination of the residual cyanide.

Jan 1, 1984

By J. H. Daniel

Dust-related respiratory disease remains the major health concern in mining, and health agencies are proposing more stringent standards. The U.S. Bureau of Mines (USBM) is investigating techniques to continuously monitor respirable dust in real-time during the coal or ore extraction process. Continuous monitoring will allow mine operators to evaluate hazardous dust concentrations and adjust the operations to produce less dust. Mine instrumentation applications include machine-mounted and hand-held monitors, personal monitors, and area/environmental monitors. Six dust detection methods have been considered to meet application requirements. These are: light-scattering instruments, a smoke-particle detection technique, correlation of pressure drop across the collection filter with amount of dust deposited, the Tapered-Element Oscillating Microbalance (TEOM) instrument, a method that relates the amount of dust collected on a filter with the vibration of the filter, and beta attenuation measurement of dust. Studies to date have identified the TEOM instrument and the technique of correlating the amount of dust collected with the vibration ofthe filter as having the most promise for success. Development of the machine-mounted monitor is the highest research priority. The application options and progress to date in developing continuous monitoring instrumentation are presented.

Jan 1, 1995

By A. M. Al Taweel, V. K. Kasireddy

Intensive coal cleaning usually necessitates fine grinding of the feed in order to liberate inorganic constituents from the surrounding organic matrix. This however adversely affects the ability of flotation techniques to beneficiate coal. Such difficulties are mainly attributed to the increase of particle population density, the decrease in capture efficiency, and the greater tendency of inorganic components to report with the froth. A three-pronged approach was adopted in an attempt to overcome these difficulties. The aggregative flotation technique was used to reduce particle population densities and improve capture, while unconventional spargers were used to generate a wide range of bubble sizes. Use of unagitated flotation columns allowed for the maintenance of countercurrent flows in both the recovery and washing sections. The combined effect of these parameters enabled the recovery of 92% of the carbon content of coal having an average particle size of 20.5 µ m, while rejecting 85% of the ash. This was accomplished using 2 kg of fuel oil per tonne of coal in a column 2 meters high operating at 2-3 tph/m3, a capacity which compares favourably with conventional cells.

Jan 1, 1989

By Michael S. Kucker, Stuart Warren, Robert A. Robinson, Michael J. Lehnen, David McAllister

Geotechnical conditions exposed by the phased exploration programs have had a major impact on the selection of excavation and support methods, dewatering requirements, size of openings, vertical alignment, and estimated cost of construction for the Beacon Hill Tunnel and Station section of the “Link” Light Rail. Beacon Hill is comprised of a very complex glacial geology, including numerous slickensided fractures, injected sand dikes, and multiple perched groundwater levels as revealed by a phased boring program and exposed in a test shaft. The Geotechnical Baseline Report (GBR) presents this complex geology along with a “tool box” of alternative additional support systems to accommodate the varying ground conditions during construction of the station excavation. Additional explorations will also be accomplished during construction to further refine the geotechnical interpretations and provide an opportunity to use pro-active ground improvement techniques to optimize the station excavation and support requirements.

Jan 1, 2005

By N. Paas

Diesel powered equipment has been operated in underground coal for more than 50 years. According to the Mine Safety and Health Administration (MSHA), there are approximately 3,000 diesel units operating in underground coal mines in the United States. This number is expected to reach 5,000 diesel units in 250 coal mines by the year 2000. Also, there are approximately 5,000 diesel units operating in metal/nonmetal mines such as trona, potash and salt mines: and more than 3,000 diesel units operating in Canada. This increased popularity of diesel powered equipment over trolley wire, electric trailing cable or battery powered equipment is because of improved safety, greater mobility, higher productivity and increased power of diesel equipment.

Jan 1, 1997

By T. Bauerle, G. Poplin, Z. Dugdale

"The issue of mine worker fatigue is as complex as it is understudied. Generally, worker fatigue lies somewhere on a continuum between psychology and physiology, which makes the measurement and management of it difficult with no easy solutions for operators or workers. Answers to even basic questions remain elusive—such as what is fatigue, how is it measured, and how can organizational resources reduce fatigue—and answers seem to present no single, clear path to action for the health and safety of the worker. This manuscript supplements the growing body of interest in the problems of fatigue in the mining industry by reviewing some of what is known about worker fatigue in general and in the mining industry in particular. The material covered here includes basic topics of the hows and whys of worker fatigue; an overview of fatigue models, findings, and evidence-based solutions with a focus on mining; and potential future directions aimed at mitigating miner fatigue. INTRODUCTION “It is recommended that the whole fatigue test problem be stated in a form the nature of which may be indicated by the following suggestions: that the term fatigue be absolutely banished from precise scientific discussion, and consequently that attempts to obtain a fatigue test be abandoned [emphasis added].” – Bernard Muscio, Pioneer Australian Philosopher and Industrial Psychologist, in a 1921 Report to the Cambridge Industrial Fatigue Research Board Fatigue presents several challenges for the mining industry. Depending on the specific occupation, daily work, or operational setup on any given mine site, mining jobs can have a fair amount of labor-intensive tasks mixed with monotonous and repetative duties. Combined with the long working hours and shift-work schedules of mining work, the prevalence of fatigue in mine workers may seem rather unsurprising. On the one hand, mining is certainly not alone in facing the challenge of addressing worker fatigue. Indeed, many of the characteristics above mirror the similarities of fatigue in other industries, such as health care, aviation, and security. To the extent that fatigue in mining acts like fatigue in any other industry, then any fatigue management applications, trainings, or interventions in existence can be borrowed from other industries and applied to mining in a “cookie-cutter” approach. On the other hand, some have argued that mining in particular is especially susceptible to increases in the prevalence of fatigue beyond the characteristics listed above due to the multifaceted combination of factors in mining environments associated with fatigue: dim lighting; limited visual acuity; hot temperatures; loud noise; highly repetitive, sustained, and monotonous tasks; shiftwork; long work hours; early morning awakenings; and generally poor sleep habits (Canadian Centre for Occupational Health and Safety, 2012; Legault, 2011). Legault (2011) in particular argues that it is the combination of these factors simultaneously that can make mineworkers particularly susceptible to sleep deprivation and fatigue in comparison to other industries where these factors are often not present alltogether. If fatigue looks and acts different in mining, as others have argued, more research is needed to determine if, how, and why worker fatigue might need to be managed differently in mining."

Jan 1, 2018

By Louis L. Sirois, Kwang S. Moon

The flotation mechanisms of various flotation machines are briefly reviewed. The counter current column flotation mechanism is described in more detail. The merits of counter current column flotation include; improved metallurgical performance in terms of grade and recovery, effective cleaning action in the long cleaning zone with a blanket of fresh water, smaller floor space required due to the vertical configuration of a flotation column, low capital, operational, and maintenance costs due to the absence of moving parts and finally, easier flotation control due to the simplified circuit. The results of column flotation studies on various minerals and coal at CANMET are discussed. Some of the industrial experiences with the Canadian flotation column on various sulphides, oxides and coal are also presented.

Jan 1, 1988

By Thomas B. Borak, Keith J. Schiager, Janet A. Johnson

INTRODUCTION Several major factors introduce uncertainties into the assessment of radon progeny exposure to miners using time-weighted average radon progeny concentrations: uncertainty in the measurement of radon progeny concentrations in specific areas, assignment of an individual miner's time to those areas, variation in radon progeny concentration between measurements and potential human errors involved in calculating concentrations and handling data. The currently available grab-sampling methods for determining working level were analyzed to determine the magnitude of the uncertainty due to each of these factors. For all measurement methods studied, the variation in the airborne concentration with time in operational areas of a mine is the dominant factor in the uncertainty in determining annual radon progeny exposures for individual miners. Uncertainties relating to accuracy of the method and precision of measurement were found to contribute a significantly greater portion of the total uncertainty than human errors. Under normal conditions, if the technicians performing the measurements are conscientious and well trained, human error contributes little to the total uncertainty of the radon progeny exposure determination. The primary goal of radiation monitoring is the reduction of radiation exposure to the lowest reasonably achievable level below regulatory limits. Monitoring personnel in mines should be trained not only to obtain accurate estimates of miner radiation exposures but also to recognize and, when possible, to implement correction of situations which result in unnecessarily high radon progeny exposures. ESTIMATION OF UNCERTAINTY DUE TO HUMAN ERRORS Human errors affecting the assignment of annual radon progeny exposure to individual miners can be placed in two categories: those related to the measurement of radon progeny concentration in specific mine areas and those related to estimation of occupancy time for individual miners and transcribing data to permanent records. The former are specific for the measurement method used; the latter are common to all methods. Errors in Determination of Working Level All systems for determining radon progeny concentration require measurement of several parameters, which include volume of air sampled, count rate and decay time. These quantities and appropriate constants are used in a basic equation, specific to the system, which estimates working level. An unintentional random mistake in measurement of any one of these parameters or in the selection of proper constants will contribute to the uncertainty in the determination of working level. In our analysis of human error we separated each measurement method into a sequence of independent operations, with each step subject to operator error. For each operation we estimated the probability of occurrence and the consequence of errors to obtain a resulting uncertainty. Certain types of errors result in specific consequences. For example, we assumed that an error of 5 seconds in timing of a 5-minute sample results in a fractional error of 1/60 (1.7%). Other types of errors can result in a range of uncertainty. Transposing digits read from a scaler can produce errors ranging from near zero to approximately 60%. In these cases we calculated the statistical variance for the distribution of errors. We assigned the square root of the variance divided by the mean as the consequence factor for that type of error. This is essentially the same as a coefficient of variation. The product of the probability of occurrence and the consequence factor is the fractional uncertainty in the measurement due to that particular error. The total uncertainty due to human errors is calculated by taking the square root of the sum of the squares of the uncertainties generated by all manual operations. Uncertainties Due to Human Error for the Kusnetz Method One of the techniques most commonly used to estimate working level in U.S. uranium mines is the Kusnetz method. A generalized way to express the equation used to compute WL by this method is: WL = (Net Alpha Counts)/(V)(ST)(CT)(E)(K) where: V = sample flow rate in liters/min ST = sampling time in min CT = counting time in minutes E = absolute counting efficiency K = Kusnetz conversion factor (dis/min-L per WL), as a function of decay time in minutes. The example of human error analysis presented here is based on the Kusnetz procedure having a timing sequence of 5 minutes sampling time, 40 minute decay time, 2 minute counting time. During the sampling procedure a stop watch is used to determine the timing interval. We assume that it is common to make small timing errors of a few seconds, but larger timing errors occur infrequently. Errors greater than 30 seconds are considered to be essentially non-existent since we assume that the

Jan 1, 1981