Search Documents

Clean Diesels fuel-borne catalyst, Platinum Plus, helps improve fuel economy for all engines up to 10 percent while reducing particulate emissions by up to 25 percent. When used with a simple diesel oxidation catalyst, particulate emissions can be reduced by 30 to 50 percent. The use of Platinum Plus enhances combustion in the cylinder, burning fuel more completely. This reduces CO2 and other greenhouse gases and lowers total operating costs by improving fuel economy.

Jan 1, 2007

By Raj K. Rajamani, M. K. Abd El-Rehman

The planetary mill is very much suited for the ultra-fine grinding of mineral fillers. Ultra-fine grinding here refers to grinding powders to a size range 5-1 0 rnicrons. Such powders enhance the quality of the final product. The operation of a specially built planetary mill is described. It is shown that a target size of 5 rnicrons can be reached in a few hours using the dual drive planetary mill. A centrifugal field of 37G is generated by the gyration arm of the mill. The design allows the desired setting of canister critical speed. The ultra-fine grinding of alumina, titanium dioxide, hematite, magnetite, kaolin and silicon carbide are described. Also, the continuous operation of the mill is shown.

Jan 1, 2003

By R. J. Roman

The results of column leaching tests on 3 different mixed oxide/sulfide ores from a Chilean deposit are presented. The 3 samples contained different ratios of oxide copper minerals to chalcocite and chalcopyrite. The results of the column leach tests are interpreted in light of the shrinking core model for coarse particle leaching. The copper recovery from the oxide minerals and the sulfide minerals each conforms to the shrinking core model with the total recovery equal to the weighted average of the individual minerals. The use of column test results to predict field heap leaching results using the multi-mineral shrinking core model is discussed.

Jan 1, 1993

A number of factors affecting the properties of cemented aggregate fill (CAF), particularly its strength development have been studied through a series of laboratory investigations carried out at the Western Australian School of Mines in the Western Australia in recent years. The outcomes of these investigations indicate that apart from cement dosage, aggregate particle size distribution, aggregate quality, additional fine materials, water salinity, admixture dosage and sample scaling all contribute significantly to the development of cemented aggregate fill strength.

Jan 1, 2001

By Marline J. Veesaert

Urban quarries offer one of the greatest opportunities for profit in non-metallic mining with limited financial risk IF properly evaluated, planned and developed to meet market needs. Location, with respect to market, is the prime consideration. Geologic considerations and quality of rock are nearly as important. Cost factors and return on investment (ROI) are the principal financial considerations. Risk of capital is determined by weighing all factors that should be considered and how well judgements are based on information acquired. It is a simple, true axiom of business that an investment must be founded on amount of capital required with its expected return plus profit, expertise required to operate and time involved. Urban quarries generally offer excellent stone product market opportunities. Costs of land with mineral containment and processing operations are much greater than in rural areas. Environmental problems have become increasingly severe. Competition from other quarries in the market area is usually directly proportional to the profit attractiveness. Risk of capital (initial, developmental and operational) can be evaluated and reduced only by thorough analysis of the entire situation. Time and money expended on planning and preliminary investigations probably represent the most productive investment of available company resources.

Jan 1, 1977

By Douglas Ball

An underground storage field is a gas field where man, not nature, has put all or most of the gas. All but one of those in use today are in the pore spaces or "porosity" of sedimentary rocks, the most common being sandstone. The one exception, near Newcastle, England, is a gas storage in a cavern dissolved from rock salt. The tens of millions of barrels of LPG (liguified petroleum gas) now stored in salt caverns mined in shale is liquid storage, not gas storage, and in this paper I recognize the presence of these installations but do not include them in the gas storage category, Since, with the English exception, gas storages are gas fields, they can all be sorted into the categories used to describe gas fields, 95% of them once gas fields anyway, but some of the remaining 5% are the ones having the greatest effects on underground waters.

Jan 1, 1960

By Edoardo Misano, Magali Schivre, Martino Semeraro, Alain Bochon

"INTRODUCTIONThe Laboratoire Souterrain de Modane (LSM) is an underground research laboratory located in the Western Alps on the French – Italian border. It is located in the middle of the 13km long Fréjus highway tunnel that links Modane (France) to Bardonecchia (Italy) in correspondence of the highest overburden of 1800m. The LSM current activity is mainly based on the investigations about the dark matter and requires very sensitive instrumentation which shall be protected from cosmic rays. To comply with the new legislation about safety in tunnels, the highway tunnels owners agreed in 2007 the construction of a parallel safety tunnel, at an average distance of 50m from the existing tunnel and the laboratory owner CNRS (Centre National de recherche scientifique) also decided to extend the existing laboratory with the construction of a new 17000 m3 cavern allowing the installation of wider and more powerful instruments that could increase chances of success of research. Preliminary studies stated that, considering both geological and functional issues, the most appropriate location for the new laboratory shall be in between the two tunnels and parallel to the existing laboratory (see Figure 1).Hence, the CNRS asked Systra, already in charge of the works supervision of the safety tunnel, to realize the design of the new cavern. The laboratory extension includes the construction of a 40 m long cavern with 300 m² cross section and two smaller tunnels connecting the safety tunnel and the existing laboratory to the new cavern. The minimum distance between the front face of the new LSM and the highway tunnel is about 25 m.The French and the Italian authorities, responsible of the exploitation of the Fréjus highway tunnel, asked the CNRS to develop an accurate study indicating that the construction of the laboratory extension would not have any negative impact on the existing structures of the highway tunnel. The main results of the developed study by Systra are summarized hereafter. The construction works should begin prior to the end of the construction works of the Fréjus safety tunnel in 2018."

Jan 1, 2016

By S. Peng, N. Vayenas, A. Farah

"While genetic algorithms have been widely adopted in ore grade estimation and optimization, mine design, and production scheduling in the mining engineering field, reliability and maintainability analysis of mining equipment using genetic algorithms has been a relatively new research area in recent years. This paper presents an application of genetic algorithms using case studies with seven underground scoop trams whose maintenance records have been collected over a period of 12 months from an underground mine in the Sudbury mining area. Based on the assumption that various factors that contribute to machine failures resemble the biological evolution process, the authors have developed an in-house PC software application called GenRel which adopts genetic algorithms in its programming. In this study, the authors feed the historical maintenance data into GenRel in order to predict future maintenance characteristics of mining equipment in a time period of three months. Then the predicted maintenance characteristics are compared to the actual maintenance records in the same time period. A statistical study is then used to examine the similarity between the predicted data and the recorded data.INTRODUCTION Today maintenance costs of sophisticated engineering systems are so high that maintainability draws great attention from scientific researchers to operations managers. For instance, a study by [1] shows that American manufacturers spend more than 300 billion U.S. dollars on plant maintenance and operations. Therefore it is understandable that the main objectives of applying maintainability principles to engineering systems are to reduce projected maintenance costs, to use maintainability data to estimate system or equipment availability/unavailability and to determine labor-hours and other related resources needed to perform the projected maintenance. A system with better maintainability would inherently provide the benefit of lower maintenance costs, less time to recover with lower breakdown frequency (design for simplicity), less complexity of maintenance tasks and relatively reduced man-hours [2]. Most maintainability functions use the Time To Repair (TTR) as the independent variable. It is common to use probabilistic or statistical concepts to define a maintainability function, for example, the probability density function. Let t denote the time. Assuming a repair starts at t=0 and completes at time T, the maintainability can be mathematically defined [3] as in Equation (1)."

Jan 1, 2015

By Victor Rudenno

Cut-off grade is one of the most critical parameters affecting project cash flow. Its sensitivity is due to the number of other parameters that are correlated with any change in its value. Changes in cut-off grade, average grade and ore tonnage vary and they in turn can affect such parameters as capital and replacement costs, recovery, life of the project and operating costs. Perhaps one of the best definitions of cut-off grade is that of Taylor (1), "... any grade that, for any specific reason, is used to separate two courses of action, e.g. to mine or to leave, to mill or to dump ... . Obviously the most likely specific reason is one governed by economics, involving the return of investment and sufficient profit to motivate development and mining of the deposit. In this paper the cut-off grade is defined as that mining limit which will maximise the economic return for a projected mining venture. The following brief literature survey indicates that when computing the optimum cut-off grade there is a need to be able to directly compute the Discounted Cash Flow Rate of Return (DCFRR) or Net Present Value (NPV), as economically as possible, while allowing for parameter dependencies and variation in project structure.

Jan 1, 1979

By Mark N. Savit

It is indeed a rarity for a non-engineer, let alone a lawyer, to even be considered for a mining-related award, especially where that award is for significant contributions to technical progress in the mining and exploration sectors. So, when I was notified that I had received this award, I struggled for a topic that would meld the legal world that I operate in with the engineering driven world of exploration and extraction. The most exciting part of my job has always been the opportunity to absorb the technical details of the cases I work on and, in effect, translate them for a lay audience. Too often, I have found, lawyers, judges, legislators and yes, even regulators who lack a technical background simply give up trying to understand the details of the very conditions or processes that they are trying to describe and simply repeat phrases told to them by their client or by a retained expert.

Jan 1, 2008

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By Alan D. Randolph

A size-continuous breakage kinetics model is postulated and supported with industrial grinding mill data. It is shown that the kinetics parameters include the effects of possible classification at the mill discharge. The estimated parameters were then used in the kinetics model to simulate the behavior of a grinding mill in open and closed circuit operation. While material transport and kinetics are equally important in open loop operation, heavy recycle in a closed circuit make a detailed material transport model for grinding unnecessary. In effect, the mill can be considered as backmixed. This suggests that more emphasis should be placed on modeling the classifier than the development of detailed material transport models for the grinding mill.

Jan 1, 1975

By W. S. Fyfe, G. Southam, T. J. Beveridge

Sporosarcina ureae was able to grow in the presence of tip to 10-ppm L-asparagine complexed gold. However, 10 ppm Au3+ was found to be highly toxic to Sporosarcina ureae, killing 109 bacteria/mL within a few seconds. To compare the effects of these responses on gold mobility, an in vitro bacterial biofilm model was developed to examine the interaction be¬tween Sporosarcina ureae and ionic gold or L-asparagine gold complexes in gravity fed columns. The immobilization of ionic gold was between 80% and 90% over a period of one week. But, as the available cellular reactive sites became saturated, immobilization decreased to 14% within two weeks. In the L¬asparagine-gold system, gold immobilization in the cytoplasm occurred at a high rate (80% to 90%) throughout the experi¬ment, with limited toxicity towards Sporosarcina ureae. The bacterial immobilization and detoxification of L-asparagine¬complexed ionic gold was associated with a low molecular weight, i.e, <5,000 dalton (atomic mass unit), intracellular protein fraction. This peptide-complexed gold would allow for the continued biogeochemical cycling of gold under ambient (<100°C) surface or near-surface conditions.

Jan 1, 2000

By John W. Wilson

INTRODUCTION In the past, the cost and time required for the construction of shafts has played an important part in the planning of underground mines. For reasons that are discussed later, the economics and technology of shaft construction in the future can be expected to play an even greater role in the planning of new mines and the operation of existing mines. Indeed, the very feasibility of a proposed mining venture may depend on the cost and timing of the shaft requirements. The most commonly used shaft sinking methods used today for excavating vertical shafts are discussed and the need for new technology and methods emphasized. In one study by the U. S. Bureau of Mines, it was reported that the coal industry in the United States alone could require 170 to 190 new shafts per year on the basis of doubling current production by the mid 1980&apos;s or 70 to 90 shafts on a more moderate coal production expansion program. This study concluded that the attainment of the required number of shafts would be unlikely with the present shaft sinking resources and costs. In order to meet the requirements for shafts in the United States coal and metal mining industries, more efficient and speedier shaft construction methods will be necessary. Current shaft sinking methods are, in the main, labor intensive, and it is noteworthy that it is becoming increasingly difficult to attract the work force required to sink shafts conventionally. Because of this situation, some attempts at mechanization have been made to compensate for this ever-increasing scarcity of trained

Jan 1, 1976

By Jan E. Stache

Commercial software programs are being utilized to create and maintain a mine subsidence database in conjunction with the U.S. Bureau of mines research on mine subsidence in Illinois. A three-year survey net of monitored structures in an Illinois subdivision was entered as textual information (attributes), on an existing AutoCAD drawing. These attributes can be optionally displayed on the corresponding drawing or extracted as a text file for import to a database program. The database program, dBASEIV, allows combinations of multiple database files for extensive querying capabilities. Subsurface database files can be merged with surface database files to enhance the effectiveness of surface response analyses in mine subsidence research. The geographic information system (GIS), pcARC/INFO, was chosen to integrate existing AutoCAD drawings and dBASEIV database files into a relational database with a graphical representation. The relational database allows users to update either the graphical representation or the database, with the changes being reflected automatically in its alternate format. The increased capacity, through use of a GIS, to query combinations of database files and have the results reflected graphically has significant potential for expediting mine subsidence research.

Jan 1, 1986

By Frank Hagar, George M. L. Robinson

NTRODUCTION The Resource Conservation and Recovery Act and CERCLA (SUPERFUND), in many instances, has had an adverse economic impact on the hardrock mining industry. Over the last few years, many abandoned and active mining operations have been added to the Environmental Protection Agency (EPA) National Priority List (NPL) . When the property is placed on the NPL the operator or EPA is required to conduct extensive environmental assessments to determine if historical mining practices have degraded the existing environmental. If degradation has or will continue, the responsible party is required to implement appropriate remedial action plans. If a responsible party is not identified, the EPA implements a cleanup program. Experience has demonstrated abandoned and active mining operations are subject to RCRA, and possibly Super- fund, if the mine has not adopted appropriate hazardous waste disposal management procedures. If off-site contamination has occurred, the operator will be required to mitigate the impacts and will be required to adopt additional procedures to minimize future impacts. Since the passage of RCRA and Super- fund, many mining operators are adopting management procedures to monitor and inventory hazardous sub- stances and wastes generated, stored and disposed on site. Many operators are in a difficult position because ore, waste rock, process chemicals or other solid waste, in many instances, can be classified as hazardous waste. If the process or other solid waste is deemed to have the characteristics of a hazardous waste, the operator can inventory and adopt appropriate, in- expensive management procedures. However, if the ore or waste rock has hazardous waste characteristics, in- expensive control technologies are impossible to implement. Since existing statutes and regulations require hazardous waste control, the operator will be required to inventory, characterize and monitor all aspects of the mining operations including but not limited to exploration, mining, ore processing and waste disposal. During this process, geological, geotechnical, geochemical, waste and ore volumes, and process materials must be tracked throughout the mining process. To accomplish this task, the most cost effective method to maintain documented and accurate records, is through the implementation of an integrated database management system. The database management system can be used to model and simulate the entire mining operation and if necessary, used to predict whether the operation is in compliance with existing regulations. The developed database can also be used to operating optimize mining and disposal costs.

Jan 1, 1987

By Donald E. Dickie

At Sifto Canada&apos;s Goderich salt mine near Goderich, Ontario, the stress control method of mining was introduced to overcome increasing roof failure problems. After successful testing, the conventional room-and-pillar mining method was converted entirely to the stress control method. This conversion has successfully stabilized the ground, increasing the extracton ratio from 38% to 50%. At the same time, it reduced the ground control and rehabilitation cost by more than 80%. The success of the conversion is due to the quantitative technique of mine analysis that was developed to ensure that the conversion was safe and reliable. A finite element model of the ground was constructed to predict and validate the safety of the stress controlled mine opening. A system of in situ stress-property measurement instruments was developed to obtain input data for the computer model as well as to evaluate its output quantitatively with regard to time and location. History of roof problems Severe roof safety problems have been encountered at Goderich Mine since it opened in 1959. These problems continued into the 1980s. Following excavation, the roof strata started to deteriorate by slabbing. Even after roof rehabilitation, deterioration continued to progressively higher roof elevations, requiring repeated rehabilitation. The operational impact of these roof failures was severe, ranging from a considerable safety hazard to major production interruptions.

Jan 1, 1993

By Barbara C. Schickner

The long-awaited COSMAR study prepared under the auspices of the National Academy of Science reaches one emphatic conclusion that has been enthusiastically seconded by the mining industry: The 1977 federal surface mining act is "poorly suited" as a vehicle to regulate noncoal mining. Though the industry greeted the report with approval, the weight it will carry and the extent of its impact are yet to be felt. The COSMAR report makes no recommendations-that&apos;s a job left to the Administration&apos;s Council on Environmental Quality-and the prospect of legislation still hovers. For a closer look at the study, MINING ENGINEERING talked to COSMAR committee chairman James Boyd, a well-known presence in the mining arena for over 50 years. After highlighting some of the study&apos;s major points, Dr. Boyd comments on the report&apos;s impact and possible repercussions. Dr. Boyd, for those readers who haven&apos;t seen the COSMAR report, would you summarize some of its major findings? The committee analyzed the surface mining act to determine if it was applicable to noncoal mining and found that there were provisions of the act that either could not be met by existing technology or would be extremely difficult and not necessarily beneficial to adapt. We found that most noncoal mineral mines, despite their obvious diversity, can be considered in two major groups: 93% of all mines move 45% of all materials mined (mostly small units mining construction materials); and the few gigantic regional operations (2%)-copper, iron, phosphate, and uranium mines-that move 50% of the material. With few exceptions, neither of the two groups is amenable to the coal mining practices addressed by the act. The strip mine law was designed for coal mining, where land is regraded, revegetated, and returned to usefulness. In contrast, construction mineral quarries supply local needs for decades, remove most of the material from the immediate vicinity, and cannot be returned to their premining uses (though they have innumerable other valuable uses). The nation&apos;s huge mineral deposits require enormous capital investments, are vital to the nation&apos;s economy, and can take centuries to exploit. Any attempt to return these locations to premining use would be illogical. Pebble phosphate in Florida and red-bed copper in Oklahoma come near to meeting the conditions contemplated in the act. In addition to COSMAR&apos;s basic finding, the study also makes the following points: •Mining uses a relatively small part of the land resource, in contrast to

Jan 4, 1980

By Edmund W. Murphy

At the first workshop on Surface Subsidence Due to Underground Mining (1 981 ) , Yarbrough delivered a paper (1 ) describing the mine subsidence insurance program in Illinois operated as the Illinois Mine Subsidence Insurance Fund (IMSIF) . In this paper we will present claims data and describe changes that have occurred in the Illinois Insurance Code during the first six years the IMSIF has been in existence. The change in the original Illinois Public Act 80-1 41 3 that most affected the public was an amendment increasing the maximum amount of mine subsidence insurance avail- able on a structure from $50,000 to $100,000. Seventy-two counties in Illinois have been undermined for minerals, primarily bituminous coal. In Franklin County (.in the southern part of the state) 36 percent of the land area has been undermined for coal extraction. In St. Clair and Madison Counties , two counties that include the St. Louis Metropolitan area along the western border of the state, 10 percent and 7 percent of the land surface have been undermined. Most of the undermined area in the two counties is beneath urbanized land. In 34 counties, approximately 1 percent or more of the land surface has been undermined (2). The first shaft mine in Illinois was sunk in the city of Belleville (east of St. Louis) in 1842, and the mines of early vintage have initiated the majority of the mine subsidence claims. Data compiled from the first six years reveals that most Illinois mine subsidence events that affect structures occur over abandoned mines where early methods of high- extraction mining practices were used. Maps of these mines operated in the 1800s reveal irregular development of room and pillar areas and poorly defined production areas (panels). Rooms in the mines varied from 15 to 40 feet in width and the pillars varied in width from 5 to 40 feet. The pillars were often long and narrow. Recovery rates in mines that operated prior to 1900 generally averaged 50 per- cent, and extraction rates as high as 80 percent have been documented (2). Some pillar robbing occurred.

Jan 1, 1986

By M. Wason

An Ore bed magnetic liner element is made of permanent ceramic magnets embedded in a rubber molding. (See figure 1) They are difficult and expensive to manufacture correctly. Therefore, the lining for a complete mill is expensive, as high as 400% more than conventional rubber liners. The magnets are not very resistant to impact as they are very brittle. Mills of 12 feet or more can use only I inch balls; mills under 12 feet can use balls of 1-1/2 inches. These liners are therefore used in regrind applications with small balls or in secondary pebble mills. Rubber liners for these applications last a long time, so if life was the only consideration, the pay back for these liners would be longer than the life of the mine. The Ore bed liner and its bed of ball chips or magnetic ore is relatively thin and the surface of this bed has a high coefficient of friction. The liners are made so that opposing poles are situated next to each other and that the mill shell and the bed of ore or ball chips completes the magnetic circuit. (See figure 2) The combinations of these properties results in a very efficient liner. Due to the low profile of this bed, there is no material that is lifted too high, so we have a very compact charge with very high attrition, good for fine grinding. These liners have shown a 10% ball consumption reduction and a 10% lower power draw for the same capacity. Due to the magnetic orientation, the bed is formed in a wave shape along the lines of magnetic force. Tests conducted at a copper mine in the southwest United States have confirmed these findings. The mills where the liners were tested are 10.5 feet by 16 feet Hardinge regrind mills operating as overflow ball mills.

Jan 1, 1999