Search Documents

By S. K. Kawatra

For efficient control of particle size in a wet grinding circuit, three alternative methods for monitoring pro- duct particle size are available. These methods are based on: 1. Ultrasonic wave absorption. 2. Low-angle forward scattering of a laser beam. 3. Inferential sizing techniques. The relative advantages and disadvantages of each technique are discussed. A particle size monitor can be used on a single grinding line to control the product particle size. To minimize the number of particle size monitors at an operation consisting of many similar grinding lines, a portable multi-stream on-line analyzer can be used. The paper outlines the design and the operational characteristics of the portable multi-stream online analyzer.

Jan 1, 1979

By R. Simon

Strain-burst phenomena are generally characterised by sudden releases of energy in a volume of highly stressed rock. Strain bursts are encountered in situations such as crown pillar bursts during cut-and-fill mining, face bursts at development headings cord floor bursts in deep shaft sinking. This paper describes a simple two-dimensional linear elastic FE modeling approach that leads to the calculation of the energy-release rate (ERR) and the total energy storage rate (TESR) in the rock-mass around the openings. The merits of using such energy parameters in the analysis of strain-burst problems for identifying areas of high energy release/storage are discussed through a case stud v. However, much site-specific back analyses are needed to better understand how strain bursts and energy parameters are interrelated.

Jan 1, 1999

By S. Aktas

The present work describes an investigation of a hydrometallurgical process for the recovery of mercury from spent silver oxide button cells. The cell paste was leached in nitric acid to solubilize silver, mercury and zinc. The optimum leaching conditions, in which mercury is entirely converted to Hg2+ ions and, therefore, does not coprecipitate with silver chloride during treatment with potassium chloride solution, were 1.0 M HNO3, 45° C, 1 hour and 200 rpm. After the silver was removed from the solution, mercury was cemented out with zinc powder with an efficiency greater than 99%. In the cementation experiments, the amount of zinc powder, shaking rate, temperature and solution pH were investigated in detail. The mercury recovery (%) increased as the amounts of zinc powder and the temperature were increased. Zinc hydroxide was precipitated from the waste solution by the addition of sodium hydroxide. The Zn(OH)2 precipitate was then converted to zinc oxide. The proposed process is proven to be simple, straightforward and environmentally friendly.

Nov 1, 2011

By Mary Fu, Helen Leung, Colin R. Phillips

In uranium mines, the median size of the aerosol has been found to be about 0.1 micron or less. Such small aerosols are readily deposited or "plated-out" on dosimeter interior surfaces resulting in the recording of a low dose. The "plate-out" properties of the CEA alpha dosimeter head are described with respect to aerosol properties in controlled experiments in the laboratory. A simple model is derived to estimate the amount of "plate-out" in the CEA head.

Jan 1, 1981

By N. J. Themelis, W. H. Dresher

Research is probably the least understood and the most underrated or overrated, depending on the circumstances, function of the corporate enterprise. Some companies become engaged in research because they consider it to be vital to their very existence, others in order to develop new business, and some with no clearer objective than to keep up with the competition. Whole new industries have resulted from research activities, such as the Xerox copier, the transistor, the computer, and have affected considerably our way of life. Companies have prospered or perished by pursuing the successes or failures of their research organizations. However. despite the tremendous effect that research has had on our modern civilization and the billions which are spent on it annually, we have not as yet been able to develop many hard and fast rules as to how to conduct it effectively and to a successful end.1 This section discusses the role of research in the United States and in the mineral industry and describes a few of the criteria and guidelines which have been developed to assist in increasing the probability for success in industrial research. Broadly speaking, the purpose of industrial research is to make a significant contribution to the long-term viability and the profitability of the sponsoring company. The sum total of technological developments has been a principal factor in establishing the United States as a world leader and the controlling element in the nation's balance of trade with foreign powers. The international aspect of most mineral commodities is a significant factor in the business decision-making of most domestic mining companies and should be an important factor in the operation of research and development (R & D) programs in these companies. The National Science Board has reported that in recent yean other nations have been gaining on the United States over practically the entire range of science. 2,3 On the positive side, the NSB reported a strong position for the US in the results derived from its investment in R & D. If the United States is to maintain a favorable trade balance, it must create new know-how through technological innovation in order to create new industrial products, processes, and services for which there is a global demand. As expressed by Chauncey Starr, president of the Electric Power Research Institute, "Unlike resources found in nature, technology is a man-made resource whose abundance can be continuously increased, and whose importance in determining the world's future is also increasing."' In recent years, the greatly in- creased pressures for environmental quality and energy conservation have enhanced further the role of technical innovation in insuring the future survival of the domestic industry. Technology is the challenge of American industry, and it is a challenge which the mineral industry must also accept, for processed minerals are the very raw materials and energy on which all of industry is based, it is technology which makes a mineral deposit into an ore reserve. The Natural of Industrial R D Research is usually thought of as being either basic or applied. Basic or fundamental research is the quest for knowledge and need not have any practical objective. Applied research is the search for a solution to a particular problem and therefore has a specific objective beyond the acquisition of new knowledge. Development is the next stage to the applied research experimentation and it generally consists of larger-scale tests to establish the technical and economic feasibility of the new process or product and to provide design information for its industrial implementation. The terms research and development are usually interconnected for the good reason that in many cases it is difficult to define where one ends and the other begins. For instance, in many cases, thermodynamic, kinetic, corrosion, and other research studies, which are needed to provide design data for an industrial plant, may prod in parallel with the pilot plant activities preparatory for this plant in order to conserve time. Often the final stages of a development project may involve the trial production of a new product for markeing tests or the trial operation of a new process on a "semi-industrial" scale pilot plant. Such operations may be termed "demonstrations"; hence, more

Jan 1, 1985

By William R. Sharp

This paper describes a graphics station and graphics software designed specifically for use within the minerals industry. Through the graphics station, a user is able to recall maps for modification, display them on a color CRT, send the work to a plotter, and restore the work when finished. The engineer may use the system for the storing of data, per- forming engineering calculations, doing word processing, and performing general file maintenance. In addition, the system may be used to communicate with a mainframe computer for such purposes as: transmission of large data files, graphic 3-dimensional rotation of a mineral deposit or mine design, contouring of spacial data, and other data processing work.

Jan 1, 1982

By Peter Cammack

Where raw coal from a mine is treated in dense medium separators ash in the washed product is generally very consistent, provided control of the medium suspension is maintained at a given specific gravity. When, however, the washing process is a Baum jig or other similar apparatus, making a separation at rather arbitrary gravities, the control of the product ash is less accurate, particularly in those cases where the design capacity of the washbox is exceeded by the load of high ash fines. In either of these cases an instantaneous measurement of ash while not essential would be desirable, to check the quality of the washed product and provide operator or management with instantaneous warning of changes in ash. Nearly 60% of all British coal mined goes for electricity generation, to burn at 17% ash, and since the overall average ash content of raw coal as mined is about 30% and varies within a range of 18 ? 40%, incombustible material has to be removed. The ash specification could be met either by total washing, or by washing part and blending the clean coal produced with the remaining untreated coal. Some plants use a straight tonnage split, but generally speaking in Britain it has been found more economical to screen and wash the oversize only. In either case for effective quality control in blending an instantaneous determination of the ash content of the product as it is made has been found essential, since standard ash determination by pyrolysis methods is lengthy and provides information too late to be used in the control of plants blending at the rate of 1000 ton/h.

Jan 1, 1976

By R. D. Williams

INTRODUCTION In a very real sense, Butte, Montana is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site. One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot Smelter operated from 1881 to 1910 moving Upper Silver Bow Creek to the south and depositing approximately 370,000 cubic yards of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot Tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 224,000 cubic yards of contaminated material. As part of the Superfund remedy, EPA proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place which set the stage for a series of studies which continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. HISTORY OF THE PARROTT MINE AND TAILINGS Placer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery lead to a stampede of placer and lode claims. One of the first lode claims located was the “Parrot” lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow and it wasn’t until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine! The Parrott mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the District’s rich copper ore. In 1885 the employees of the Parrot Smelter bought the Butte Reduction Works, another smelter. In 1885 dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Figure 1).

Jan 1, 2019

By V. M. Johnston

The most abundant fuel resource in the U.S.A. is also the most under-utilized. Proven reserves of bituminous coal, sub-bituminous and lignite constitute from 60% to 90% of our total fossil fuel reserves -- dependent upon the parameters used by the analyst making the estimate. Despite this ample supply, bituminous coal provided only 20% of U. S. energy consumption in 1967 and 1968, this dropping to 17.57 in 1971 and 1972. By 1978, according to my projections, 16.7% of the Nation's mechanical energy will come from bituminous coal. However, our energy needs are growing at such a rate that the 20.6% provided by bituminous in 1967 equalled 480 million tons while the 16.7% of U. S. consumption visualized for 1978 will require nearly 650 million tons. In order to view coal's position with perspective in this developing energy crunch, it is necessary to examine the total energy situation. To this end, I have prepared a couple of tables which you should have before you. I chose this procedure rather than slides because I would need to utilize an entire wall to make the data visible to an audience. Therefore, I refer you to the long sheet entitled "U. S. Energy Consumption - Trillion Btu - 1967-1978." As you can see from the heading, I am confining my treatment of the problem to the intermediate term. In the long run, if we are willing to pay the cost, we can do a lot of things, including the complete conversion of coal into a sulfur-free fuel.

Jan 1, 1973

By N. D. Jagger

In order to maximize the benefits obtained from flocculating agents when used as settling aids in high rate and conventional thickeners, it is often necessary to dilute the thickener feed prior to flocculant addition. In some cases, no flocculation at all is possible unless dilution water is used. The most common method of diluting thickener feed has been to recirculate some of the thickener overflow by means of a centrifugal pumping system. This represents a significant capital and operating cost. Supaflo Technologies of Australia has developed and patented an internal recirculation method known as Auto Dilution (or "Autodil") which is based on the principle that an hydraulic head differential exists between the inside and outside of the feedwell because of the higher S. G. of the pulp inside the feedwell, By installing non-return ports in the feedwell wall at the appropriate level, supernatant solution flows into the feedwell at a calculated rate and dilutes the feed without any need for external recirculation of overflow.

Jan 1, 1993

Unless otherwise indicated, pounds are US avoirdupois, feet are US, and gallons are US.

Jan 1, 1985

By J. D. McKay

Flotation columns have been readily accepted for use in most sulfide flotation plants; however, recently columns are being used in many other areas. Recent improvements in design methodologies have overcome many operating problems and led to improvements in metallurgy. In addition, physical improvements in column design have simplified their operation while leading to better control. The Turbo-Air External Bubble Generator has provided a method for bubble size control and variation in air holdup and carrying capacity. These have enabled commercial operations to improve grades and recoveries by optimizing performance.

Jan 1, 1990

By F. S. Knoll

The high tension process which separates materials based on relative differences in surface conductivity has been very successful in recovering non-ferrous metals from municipal waste. Aluminum is by far the largest constitutent of the total non-ferrous metal fraction; accounting for >95% in most localities. Wire and insulation mixtures from industrial wastes have been treated commercially for several years by a high tension process initially developed for use in the iron ore industry. The wire and insulation application was a forerunner of municipal waste dry treatment technology. In the past eighteen months the rotating-drum-type electrostatic separator has undergone extensive testing and development in order that the process might be efficiently adapted to the recovery of aluminum from municipal waste.

Jan 1, 1974

By William J. Miles, Raymond E. Blair

The oil and gas drilling industry is the largest user of "functional" industrial minerals for well drilling and completion. (Functional industrial minerals can be defined as those used for performance characteristics rather than composition.) This industry's use of industrial minerals involves complex mining, processing, and distribution of products. The cost of these products at the well site reflects the complexity of distribution to typically remote locations and the cost of service. Table 1 illustrates the use of functional industrial minerals by the drilling industry. The total tonnage shown is almost 2 1/2 times larger than the 3.3 Mt (3.6 million st) of kaolin used by the paper industry for filling and coating, another major use for functional industrial minerals. Drilling fluids are an indispensible part of a drilling operation. These fluids perform several functions simultaneously. They cool and lubricate the drill bit, remove formation cuttings, increase the specific gravity of the fluid to counteract formation fluid pressures, provide a filter cake on the wall of the drill hole to prevent drilling fluid loss to the formation, protect the porosity of producing zones, and prevent reaction of the formation or formation fluids with the drilling mud. When porosity of a formation exceeds the ability of the drilling fluid to form a wall cake, it is referred to as lost circulation. Because these fluids are being constantly formulated for changing formation conditions, they require a skilled technician or drilling mud engineer on the site at all times. Drilling fluids are composed of oil or water as the liquid phase, and industrial mineral products and chemicals to control chemical and physical properties. The basic function of viscosity and suspension result from the use of gelling clays and chemical and mineral dispersants; specific gravity of the mud is adjusted with mineral weighting agents; filtration control is maintained by clays and various natural and synthetic polymers; platey minerals and scrap products are used for controlling lost circulation in porous or fractured zones; salts are added to the mud to inhibit shale and clay swelling; chemicals are added for pH adjustment, prevention of corrosion, and as scavengers for formation fluid components. Because of the clay component, drilling muds have rheological properties different from conventional fluids, behaving as Bingham plastic fluids as opposed to the Newtonian behavior of water and oil. Newtonian fluids will begin to flow with the application of any force, however small. Bingham plastic fluids require a finite force or shear stress (yield value) before flow begins. Thixotropy is another property of clay-based drilling fluids. At rest they form a gel structure that suspends the weighting agents and rock cuttings. These gels break down when a finite force is applied and circulation is restored. At the bit where shear rates are the greatest, the viscosity or resistance to flow decreases, so hydraulic pressures and pumping costs are minimized. A drilling rig provides a means of rotating a hollow pipe attached to a cutting bit. A mud pit or tank is used for mixing the drilling mud and its components. A centrifugal pump delivers this fluid to the drill ripe and down to the bit

Jan 10, 1983

By Rainer Antretter

"THE CHALLENGE The 14km long, Arlbergtunnel, closed for public traffic during summer 2015, receiving a comprehensive and substantial renovation from 2015 to 2017. The main works discussed here, carried out during 2015, comprise 37 drill and blast SEM/NATM emergency escape tunnels from road level to the ventilation duct plenum have to be constructed as well as eight additional lay-by niches and three transformer tunnels. This presentation comprises the construction ventilation design, designed according to national regulations, suitable for 150 employees working 24/7 simultaneously at more than 40 single working sites lined up along the tunnel. The ventilation-system chosen was utilising two existing shafts for intake/discharge and a cross passage to surface, to handle a total fan power of 1.600kW. DESCRIPTION OF RENOVATION WORKS Linking Tyrol and Vorarlberg, two Federal States of Austria, the Arlbergtunnel is a single tube two-way road tunnel with vent duct plenum, constructed in the mid-1970s. According to latest EU legislation, additional escape exits have become obligatory. The existing seven cross passage links to the adjacent Arlberg Railway Tunnel, with average spacing of about 1.500m constructed in 2007, an additional upgrade to shorter escape spaces of approx. 400m was now required to comply with the updated legislation. Additional transformer tunnels, lay-by niches and small niches for emergency maintenance use, cleaning and other purposes, as well as a the installation of a new fire main in the invert, coupled with the simultaneous replacement of virtually the entire power and signaling cables, generated several dozen small and large single sites distributed along the 14km of tunnel.Purpose of the 37 walkable emergency escape tunnels is to reach the “upper deck” of the Arlbergtunnel, the vent duct plenum. These have an 180deg curve in plan, inclined at 10% and approx. 60m (65yd) long tunnels, excavated using drill and blast method starting from road level and working upwards to the level of an “intermediate soffit”, the vent duct plenum in the crown of the tunnel. The vent duct plenum is separated into a fresh air part and an exhaust air part, shown in Figure 1. The escape tunnels end with a pressure door in the fresh air section of the ventilation duct plenum. From there illuminated signs show the shortest escape route to the safe area between the road tunnel and the railway tunnel, as shown in Figure 2."

Jan 1, 2016

By K. Wenrich

The uranium industry has made a dramatic turnaround in the past three years that even the most optimistic economist was not willing to predict during the uranium downswing of the 1990s. Uranium reached a 30-year low in February 2001 of $6.50/lb. By the end of February 2006 it had soared to $38.50/pound. This nearly 600% increase in the uranium spot price within 4 years dwarfed the increase in gold price that has barely mustered a 100% increase. The initial slow rise from $6.50 in February 2001 to $10.75 in April 2003 (fig. 1) was primarily driven by the decrease in the value of the dollar. Since then several factors have contributed to the soaring price: (1) The awakening of many to the simple fact that uranium supply has not met demand for several years and that the world’s stockpiles are being drawn down, (2) How sharply this fragile supply can be impacted by disasters at the world’s major uranium production facilities, such as a) the flooding of the McArthur River Mine in the spring of 2003, b) fires at Olympic Dam, c) the potential that Rossing, with an annual capacity of 4000 tonnes uranium might close by 2007, (3) the withdrawal of Tenex from the HEU (highly enriched uranium) feed agreement, and (4) the announcement by the Chinese of their intent to build 30 new nuclear reactors.

Jan 1, 2007

By R. W. Waytulonis

This paper is an update of the activities of the U.S. Bureau of Mines, other government agencies, and the automotive and truck industry concerning diesel emission control. Enacted and proposed regulations from the U.S. Mine Safety and Health Administration (MSHA) and developments in diesel emission control are presented in terms of their impact on underground coal, metal, and nonmetal mines. Mine air quality regulations proposed by MSHA may require the underground mining industry to comply with new standards. Some mines may be required to take additional actions to meet new diesel particulate and lower nitrogen dioxide exposure standards; however, the mining industry is in a position to benefit from emission controls developed for the on-highway diesel engine market. The U.S. Environmental Protection Agency (EPA) has enacted regulations to reduce emissions from on-highway diesel trucks and buses. Engine manufacturers have responded by developing cleaner burning engines. Fuel producers have responded by providing cleaner burning reformulated diesel fuel, and exhaust aftertreatment devices have been developed to provide additional emissions reductions. Bureau research and development projects seek to determine the advantages of using modern engines and fuels, and to evaluate the efficacy of new exhaust control devices on mining machines. It appears that the diesel engine will continue to be a practical power source for use in confined environments because no other available power source is as mobile and efficient.

Jan 1, 1993

The extraction and processing of minerals from surface mines and quarries can produce significant fugitive emissions as a result of site activities such as blasting, unpaved road haulage, loading, primary crushing and stockpiling. Uncontrolled fugitive dust emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. Simulation technology is finding increasing use for the purposes of advanced warning of potential problem emissions in addition to providing a basis for future planning applications where demonstrable compliance with regulatory requirements are necessary. The initial re-entrainment and subsequent dispersion of fugitive dust presents a process complicated by the combination of the in pit topography, the surrounding natural topography and the dynamic nature of emissions from these sites. These factors impact upon the accuracy and reliability of the conventional Gaussian plume based computational prediction methods employed for regulatory compliance and IPPC applications. This paper proposes that optimal modelling of open pit emissions may be more accurately achieved by the use of a multi-scale predictive modelling approach utilizing computational fluid dynamics (CFD) methods for high resolution near source dispersion and conventional Gaussian based methods for far field dispersion modeling. This paper presents a numerical based flow and dispersion analysis of a typical UK based open pit utilizing CFD in conjunction with a conventional Gaussian plume based methods. Typical operating emissions and meteorological conditions are obtained from long term data records collected at a large operating quarry extraction operation in the UK. Emissions are modelled using a Lagrangian framework within conventional atmospheric boundary layer (ABL) profiles expressed as functions of turbulence and velocity parameters under assumed neutral conditions. Results are presented in terms of the impact of site topography on in pit retention as compared to the Gaussian based method.

Jan 1, 2009

By B. A. Comley

Over the past few decades a great deal of effort has gone into characterizing the effects of frother type and concentration in flotation using a variety of two-phase techniques. Whilst useful and informative, this research still does not assist in the selection of suitable frothers for three-phase industrial-scale froths. This paper investigates the effects of frother type and concentration in a three-phase industrial froth. The objective was to determine if progress could be made in terms of understanding the behavior of frothers in flotation and understanding how they affect the sub-processes occurring in the pulp and froth phases and, ultimately, the metallurgical performance of a flotation cell.

Jan 1, 2007

By Richard L. Stein

INTRODUCTION Increasing a miner's chance of surviving a disaster requires advance planning for emergencies, adequate training of personnel, and the provision of proper survival equipment. It is extremely important that fires and toxic gases be detected early, and that warning systems such as stench, audible and visual alarms, and communications systems be provided to allow timely escape. However, situations do occur where timely warning is not provided and immediate escape is not possible, regardless of the precautions that are taken. Under such circumstances, a combination of new per¬sonal protective devices and old techniques can provide protection that is adequate to save a miner's life. SELF-RESCUE EQUIPMENT Self-rescuers are devices which provide a short-term supply of respirable air under the potentially lethal con¬ditions following a mine disaster. Functioning either as filtration devices for the elimination of carbon monoxide (CO) or as oxygen supplies, self-rescuers allow an endangered miner a limited amount of time in which to effect an escape or reach a place of temporary safety. Carbon-Monoxide Self-Rescuers For almost 50 years, filtration self-rescuers have protected miners' lives following explosions or fires. Designed to eliminate carbon monoxide from inhaled air, the first of these devices was approved in the 1920s and has evolved into the two units that are approved today-the Mine Safety Appliance (MSA) W-65 and the Draeger 810. Both of these units rely on the cata¬lytic conversion of very toxic carbon monoxide to rela¬tively safe levels of carbon dioxide (CO,). As shown in Figs. 1 and 2, both of these filtration self-rescuers operate in the same manner. On inhalation, the mine air passes through both coarse and fine filters that remove the dust, preventing the dust from coating the chemical beds or entering the miner's mouth. The air then passes over a drying agent that removes water vapor; this is required to prevent the water vapor from poisoning the catalyst. Subsequently, the dried air passes over the Hopcalite catalyst, where carbon monoxide is converted to carbon dioxide. Then, the air passes through a heat exchanger that reduces the temperature of the inhaled air. Finally, the air is inhaled by the user. Air exhaled by the user passes through the heat ex¬changer and exits the device through an expiratory valve. Both units of this type are subject to certain limita¬tions: 1) The units do not protect the user against oxygen¬deficient air; when air is inhaled through this type of self-rescuer, the device only removes the carbon mon¬oxide. If the mine air contains less than 15% oxygen, anoxia is inevitable. Symptoms of anoxia include dizzi¬ness, shortness of breath, quickened pulse, and deeper and more rapid respiration while the victim is at rest. During heavy exertion such as would be expected dur¬ ing escape efforts, a 15% oxygen level can cause loss of consciousness. 2) The units do not protect against excessive levels of carbon dioxide. Available data on carbon monoxide and carbon dioxide concentrations following explosions or fires are limited, but there are indications that the carbon monoxide concentration can rise to 2% and the carbon dioxide concentration can reach 5 or 6% of the mine air (by volume). In some situations, the in¬haled air could contain up to 6 or 7% carbon dioxide. At a carbon dioxide concentration higher than 2%, breathing patterns can be affected adversely. At a con¬centration of 6 or 7%, the effects include severe respira¬tory distress, with unconsciousness resulting from exer¬tion such as that needed for escape activities. 3) The units do not protect against high inhalation temperatures. The catalytic oxidation of carbon mon¬oxide to carbon dioxide is an exothermic reaction that evolves a large amount of heat. As the carbon monoxide concentration increases, the temperature of the inhaled air also increases. Available data show that above 1.5% carbon monoxide, the air inhaled through some self¬rescuers can be as high as 90°C (194°F). At those

Jan 1, 1982