Search Documents

Acid Mine Drainage (AMD) is the most serious environmental problem facing the Canadian Mineral Industry today. Acid Mine Drainage results from oxidation of sulphide minerals (e.g. pyrite or pyrrhotite) contained in mine waste or mine tailings. It is characterised by acid effluents rich in heavy metals that are released into the environment. A new acid remediation technology is presented in this paper by which metallurgical residues from the aluminium extraction industry are used to construct permeable reactive barriers (PRB) to treat acid mine effluents. It describes column tests performed to simulate a PRB using Bauxsol?, a chemically and physically treated bauxite refinery residue, as a reactive material. This experimentation shows promising results for the Bauxsol? PRB method in neutralizing pH and removing metals from acidic mine effluents.

Jan 1, 2006

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

"The 35th Annual American Mining Hall of Fame Awards Banquet and Fundraiser, sponsored by the Mining Foundation of the Southwest (MFSW), will be held at the JW Marriott Tucson Starr Pass Resort & Spa on Saturday, Dec. 2, 2017. This year, the Foundation will honor one living Hall of Fame inductee, two Medal of Merit recipients, four honorees from Mining’s Past and an Industry Partner for their respective contributions to the mining industry.Gary J. Goldberg will be the 2017 Hall of Fame Inductee and will serve as the keynote speaker at the awards banquet. Goldberg was appointed president and chief executive officer and joined the board of directors of Newmont Mining Corp. in March 2013. Prior to this appointment, he served numerous companies in key positions including Rio Tinto Minerals, US Borax and Coal & Allied Industries. At every appointment, he was able to improve safety concerns and reduce injury rates. While serving as chairman of the National Mining Association, Goldberg launched the CORESafety initiative and US Borax was the first mining company to receive the California Governor’s Environmental and Economic Award.The Medal of Merit will be awarded to John C. Lacy, a shareholder of DeConcini McDonald Yetwin & Lacy, P.C. and a director of the Global Law Center at the University of Arizona’s Law School. Lacy’s law practice concentrates on mining and public land law and encompasses transactional and title consideration involving acquisition of mineral rights. He played a crucial role in the revisions to the mining law of the Republic of Bolivia and the English translation of the mining laws and regulations of Mexico. Lacy’s expertise in mining law impelled the University of Arizona James E. Rogers College of Law to approach him to head the new Global Mining Law Center in 2015. The program now partners with the Lowell Institute for Mineral Resources and offers cross-listing of courses"

Jan 10, 2017

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993

By H. Colijn

Introduction Bulk commodity prices are ever increasing. This forces buyers and sellers in world markets to look more carefully at methods for obtaining an accurate accounting of commodity transactions in commerce and materials utilization in processes. Weighing and sampling inaccuracies can result in loss of income, product quality, and cost controls. So weighing and sampling accuracies are extremely important. They are the key components of managing the quantity and quality control aspects of bulk materials handling. This article will confine itself to the weighing systems and will deal with various aspects of system design, calibration, and operations. Emphasis will be placed on new developments and requirements in this field. Weighing methods To measure the gravimetric pull on a body being weighed (the load), the gravimetric force must be countered by an opposing force. Measuring this counter-balancing force thus becomes the measurement of weight. The conventional even-arm balance shows the concept of balancing an unknown mass with an equal known counterbalancing mass. But the loads encountered in industry generally range up to many thousands of pounds. So it is obvious that the even-arm approach is not practical. Thus, with the exception of direct load-bearing load cells, most of the weighing equipment uses some form of lever system. This is usually a combination of first- and second-class levers, to gain a mechanical advantage. These levers permit the load force to be counter-balanced and hence measured within a practical range. Lever systems not only perform this force-reducing action, they also serve to focus the load force at a single point, for convenient measurement. They align the force vertically in one direction so that measurement accuracy will not be affected by unrelated side forces. There are five basic methods of gravimetric weight measurements. That is, there are five basic types of opposing forces. • The first is the standard weight counterbalance. It uses a known weight to counterbalance the load directly or through a lever system.

Jan 9, 1988

By Bernard Lippe

The successful construction project is one in which the component construction operations are completed within the scheduled time and cost parameters. Most construction projects, however, are subject to delays and/or disruptions which adversely affect the time (start, duration, and completion) and cost aspects of the project. DELAYS Delays fall into two categories: Compensable Delays for which the contractor is entitled to contract time extensions and additional money as compensation for the extra expenses generated by the delay or obstruction to job progress, and Non Compensable Delays, for which the contractor may or may not receive an extension of time but no additional compensation. Compensable Delays Compensable delays may take the form of holds or suspensions on all or certain segments of a project by the owner, failure of the owner or his Engineers to approve shop drawings, cuts or material samples within a reasonable period of time, failure of the Owner or his Engineer to properly coordinate the job, discovery of design deficiencies in the plans and specifications which prevent the continuation of construction until

Jan 1, 1974

By P. R. Dugan

The ultimate objectives and interest in removal of sulfur from high sulfur coal include: (a) reduction of the atmospheric load that con- tributes to the problem of acid precipitation; (b) reduction of ash which contributes to decreased energy transfer in boilers and the problem of ash disposal; and (c) alleviating the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. The cost of sulfur removal in relation to the value of refined coal will govern the development of an emerging coal-refining industry. The value of refined lower sulfur coal will be influenced by the national commitment to the environment as well as economic considerations.

Jan 1, 1986

By K. W. Lentz

The Maybell Mill of, Trace Elements Corporation, Unit of Union Carbide Corporation is located approximately five miles northeast of Maybell, Colorado, and twenty-five miles northwest of Craig. It is located in the midst of the uranium ore deposits whose presence, made it possible. In November 1953 Russel Cutter, Chief Geologist for the original Trace Elements Corporation, picked up high readings on a scintillometer while flying over this area. Later, with George Morehouse, Chief Engineer for the original. Trace Elements Corporation, he started a search for surface indications. In this search, they found an out crop which can be regarded as the discovery lode on this property. The actual locating of claims and acquiring free lands and state lands was begun in March 1954. During 1955 enough drilling was done to indicate that a sufficient tonnage of ore existed to make possible a mill. These ore deposits are located in the Browns Park formation which is an unconsolidated sandstone with a few hard lime ribs running through it. The geologists tell us that this region was once a vast basin which became filled with wind blown sand and volcanic tuff, Later on, ground waters brought uranium into the basin which precipitated out in the sand. During the late summer and fall of 1955, a small pilot plant was operated under the supervision of John L. Chapman testing these Browns Park ores. During the operation of the pilot plant, three small open pits were developed and the ore from these pits shipped to Union Carbide Nuclear Company, Division of Union Carbide Corporation, at Rifle. To date all ore is being mined from open ptis. In the fall of 1956 the original Trace Elements group signed a contract with: the AEC for a mill at Maybell and on November 5, 1956, Union Carbide acquired the Trace Elements Corporation properties and contract. During the next two months, intensive research was carried out on the Browns Park ores by our research lab at Rifle. They also checked some of the metallurgical results which had been obtained through the operation of the pilot plant by the original Trace Elements group. During this period, a report on Trace Elements Corporation ores was also prepared by the Colorado School of Mines Research Foundation. This report contained data on representative samples of the ore tested for the original Trace Elements group. From this research and study a flow sheet was decided upon.

Jan 1, 1959

By Kang-Hyun Lee, In-Mo Lee, Byung-Kyu Kim, Parkm Jinho, Seoung-Won Lee

"In this study, the TBM Resistivity Prediction (TRP) system is developed for predicting the location, thickness, permittivity ratio and electrical conductivity of anomalous zones ahead of tunnel face using the measured resistivity of the ground. The applicability of the developed system was verified by performing field tests at a construction site in which an EPB-shield TBM is used for tunnelling work. In the first field test, it was found that the rock around the tunnel face had the same resistivity and permittivity with the rock ahead of the tunnel face indicating no anomaly ahead of the tunnel face. In the second test, a stronger zone 5-m thick was predicted ahead of the tunnel face based on lower permittivity than that of the rock around the tunnel face. The ground condition assessed by the newly developed TRP system matched well with that either predicted from geophysical exploration or directly obtained from drilling boreholes or from daily observed muck conditions. INTRODUCTION During tunneling work, the emergence of unpredicted zones of relatively weaker or stronger ground can lead to delays in construction work or an increase of construction cost. Predicting anomalous zones ahead of tunnel face in advance can thus prevent time and economic loss. For these reasons, various methods to predict the ground condition ahead of the tunnel face have been studied and developed. Prediction methods using various kinds of equipment include tunnel seismic prediction, ground penetrating radar, electromagnetic surveys based on electronic antennas, and electrical resistivity surveys conducted by analyzing electric currents in the ground ahead of the tunnel face (Ryu et al. 2008). However, most of the prediction methods are only applicable to conventional tunneling job sites, which feature free access to the tunnel face. In mechanized tunneling projects, accessibility to the tunnel face is very limited because the tunnel face is occupied by the TBM."

Jan 1, 2016

By Martin H. Stanczyk

In recent, years the demand and consumption of finely ground industrial minerals has substantially increased for such uses as fillers and chemically reactive components. The size, specifications for these types of industrial mineral materials vary to a great extent and depend on the particular end purpose' and on the physical properties of the mineral itself. Size reduction of industrial minerals usually is obtained by conventional crushing and grinding methods. However, some specialized milling techniques have been developed for producing these minerals in extremely fine particle size ranges. During recent years the Bureau of Mines has been investigating an attrition grinding method to produce ultrafine subsieve-size mineral particles. The Bureau developed process, which has been patented,2 comprises the intense agitation of a slurry composed of the material to be ground, a relatively fine granular grinding medium, and a suspending fluid. The process has been shown to be effective for the comminution of kaolin in the particle size range of 2 microns and finer on a batch3 and continuous basis.4,5 This report presents the results of batch tests made to determine the effectiveness of the attrition grinding process for comminuting commercial products of (1) mica, a tough lamellar material, (2) fluorite, a brittle intermediately hard material, and (3) barite, a relatively soft, massive material.

Jan 1, 1967

By Patricia Pride, Kurt Bettger, Jack Raymer

"INTRODUCTION The Jefferson Barracks Tunnel is in the final stages of design and is expected to go out to bid in the summer of 2016. The project is located in south St. Louis County along the west bank of the Mississippi River, about 13 km downstream of the St. Louis Gateway Arch. The project consists of a deep sanitary sewer tunnel, a deep pump station and several intakes. The intakes will divert sanitary flows into the tunnel and the tunnel will convey the flows by gravity to the Lemay No. 3 Pump Station, which will pump them up into the Lemay Waste Water Treatment Plant. The tunnel is about 5.4 km long and will be lined with 84-inch (2.1 m) fiberglass pipe. It drops at a gradient of 0.1 percent from south to north and will be bored through strong limestone using a hard-rock tunnel boring machine (TBM). The diameter of the TBM is anticipated to be about 3.4 m. The Owner’s original concept was for a relatively shallow tunnel so as to minimize construction and pumping costs. The preferred alignment ran close to the river, next to the existing force main, which was to be abandoned. Keeping the tunnel close to the force main would reduce the amount of shallow sewer work needed to connect the existing feeder sewers to the new tunnel. Several geotechnical investigations were performed, with shallowly focused geophysics and the borings all going exactly down the conceptual tunnel depth. Limestone bluffs run along the Missouri side of the river. These bluffs are pockmarked by sinkholes and riddled with karst. Large, well-known caves occur both north and south of the alignment. Karst features, including deep crevices and possible caves, were found in those early geotechnical investigations. Many of these features extended well below the level of the Mississippi River and would have been encountered by the tunnel. If a large crevice or cave were encountered, then the inflow of mud and water into the tunnel could have been large and possibly uncontrollable. Something had to be done to mitigate this situation. Pre-excavation grouting was considered, but the program would have been huge and extremely expensive. Using a closed-face TBM with bolted and gasketed lining was also considered, but that too was both risky and extremely expensive. The Owner could have abandoned the tunnel altogether and built a new force main, but that would have brought a whole new set of problems and was undesirable to the Owner. The last option was to move the tunnel away from the karst."

Jan 1, 2016

By D. D. Misra

Though computer simulation of coal beneficiation has been in use for nearly two decades the models used in the programs for the simulation of the crushing processes concentrate mainly on the size distribution. This paper suggests the use of an empirical equation approximating to the cumulative probability or error function for the simulation of the liberation process in coal crushing. The algorithm outlined here can be incorporated in a computer program already having a size distribution model.

Jan 1, 1989

By R. L. Virta

Four companies mined ball clay in four States during2004. They were H.C. Spinks Clay (owned by Franklin Minerals) Kentucky-Tennessee Clay (owned by Imerys),Old Hickory Clay and Unimin. Production was estimated to be 1.46 Mt (1.61 million st) valued at about $56.9 million, based on a preliminary survey of the ball clay industry. In 2003, production was 1.31 Mt (1.44 million st) valued at $56.2 million. Tennessee was the leading producer state with 61 percent of production. It was followed by Texas, Kentucky and Mississippi.

Jan 1, 2005

By S. T. Hall

The authors have previously described a method of enhancing the magnetic susceptibility of pyrite by a mild alkaline oxidative pressure leach (Hall et al, 1985). This finding was successfully applied to enhance the magnetic desulfurization of an Eastern Canadian coal (Hall and Finch, 1984). This paper reports on enhancement of the magnetic susceptibilities of iron-containing sulfides (arsenopyrite, chalcopyrite and marcasite) upon similar treatment. It also explores the application of this pretreatment in the magnetic separation of fine sulfides from oxides and other sulfide minerals. In the latter case galvanic interference effects have a serious impact on the potential use of this method.

Jan 1, 1985

By N. E. Norman

The big hole drilling industry is a relatively new one. In fact, very little big hole drilling was done prior to 1950. If there is to be a marriage between big hole drilling and mining, we should certainly take a look at the background of the big hole drilling industry. Let us examine the three main features of big hole drilling and determine how each applies to mining. Let's also look at the good qualities and the limitations of each of these character traits.

Jan 1, 1968

By Henry Antwi

The decade of the 1990s promises to be one of increasing internationalization for domestic minerals producers as they scramble to enhance relative positions in highly competitive, international minerals markets. This "international mining rush" is fueled by developing countries seeking international investment capital to explore for, develop and exploit sizable mineral endowments in an attempt to support the increasingly popular, but expensive, wave of democracy and selfdetermination sweeping the world. This "fuel" typically takes the form of revised mining codes and, often, lucrative investment incentives. These incentives include favorable tax rates, royalty provisions, relaxation of import/ export constraints, depreciation schedules, profit repatriation and other variables that can positively impact mineral investment decision making. Concomitantly, in their attempts to address real and perceived short- and long-term woes associated with enhancing competitive positions internationally, many domestic explorers and producers are attracted to the prospect of finding high-grade deposits in relatively virgin areas. Combined with the investment incentives provided by foreign governments, these high-grade deposits promise lucrative potential returns from projects having short payback periods. Classic examples of this mutual desire to intensify international mining efforts by domestic producers are illustrated by activity levels in countries like Chile, Bolivia and Venezuela in Latin America and, more recently, in Eastern Europe and select locations in the former Soviet Union. As US corporations scurry to send fact-finding, technical, evaluation and financial teams to these presently popular locations, one area of the world has received little attention - Subsaharan Africa. Specifically, the country of Ghana (formerly the Gold Coast) deserves more attention than it appears to be receiving from North American mining companies.

Jan 1, 1992

By C. R. Fahnestock

One of the major problems for us in the earthmoving industry is the analysis of materials under the ground surface. Countless engineering and construction jobs would be simplified if there were an inexpensive and fast way to obtain information on problems such as: Depth and solidith of bedrock? Nature of the materials between bedrock and the surface? Adequate foundation for bridges and drainage structures? Location of supplies of materials to be used in construction? Investigation of tunnel sites? Characteristics of swampy areas and investigation of existing and potential slide areas? These questions are of paramount interest to highway contractors as they bid jobs and plan, equipment spreads to handle them at optimum efficiency. Such information also is invaluable to engineers in the design and construction of bridges, buildings, railroads, canals, and tunnels.

Jan 1, 1961

By A. Tobey Yu

The smelter is the heart of a copper producing operation. Its principal function is to reduce and convert raw copper concentrates and/or leach plant precipitates into blister copper before it is refined. In addition to concentrates and precipitates, typical feed to a smelter also encompasses matte chips, flue dust, flux and lime. By nature, the characteristics of these materials are extremely variable, ranging from sub-micron to lumps, from slurry to dust, from abrasive to corrosive and free-flowing to adhesive. Furthermore, as a result of geological formation, most of the world's open pit copper mines are located in a semi-arid zone, where precipitation is minimal. This particular climate compounds the problem of handling these materials.

Jan 1, 1976

By J. T. Graves

Bauxite, dolomite, and magnesite are natural occurring minerals that are used extensively in the manufacture of refractory products. In addition, magnesia produced from seawater or brine finds its way into the production of refractories. All of these materials must be processed at high temperatures, 1500°C to 2200°C, to produce an intermediate raw material (refractory grain) , which can then be used in the final manufacture of refractory bricks and shapes. During the last 20 years, the major supply of refractory bauxite has been from Guyana, and at times the annual production has ranged up to 1,000,000 tons per year. More recently, China has become a major source of refractory grade bauxite by supplying over 300,000 TPY. Other sources of bauxite in lesser quantities have been Surinam, Brazil, and the U.S.A. During 1980, the estimated available world tonnage amounted to slightly more than 1,300,000 tons. The bulk of this material has been calcined in rotary kilns except for some of the Chinese production, which was treated in shaft kilns. Recent work has indicated that an excellent product can be produced in the Nichols Shaft Kiln using much less fuel than the conventional rotary kiln. Details of the Nichols Shaft Kiln will be provided later in this paper.

Jan 1, 1982

By Barry N. Doyle, Tarcisio M. Carvalho, Alan K. Haines, Marcos P. de Melo, Edward J. da Silva

A metallurgical complex to recover gold from highly refractory arsenical ore was recently commissioned by Sao Bento Mineraco. The plant, with a nominal capacity of 20 000 tonnes per month, is situated in the Minas Gerais province of Brazil. The process consists of run-of-mine milling, flotation, pressure oxidation of the concentrate, carbon-in-leach, elution and electrowinning, and effluent disposal. The paper provides an account of the investigations that resulted in the decision to install the pressure oxidation circuit, process and engineering design and plant start up. A comparison is made between the results achieved during the first two years of production and the design parameters.

Jan 1, 1989