Search Documents

By J. S. Gardner, K. E. Houston, A. Campoli

INTRODUCTION Disposal of coal refuse is a costly and challenging problem facing the coal industry today. After the Martin County Coal Company slurry spill and the subsequent regulatory changes state and federal agencies are now beginning to require companies to justify new slurry impoundments. The authors have performed an analysis of different means of disposing of coal refuse for a major coal producing company located in the eastern Kentucky coalfields (the name of which will be withheld for the purpose of this paper). The company’s existing slurry impoundment is nearing its maximum permitted elevation and also an elevation where it may come in contact with abandoned underground workings. Due to the increased concern with underground mine works near slurry impoundments, additional consideration was given to raising the existing impoundment. Several other alternatives were evaluated, including but not limited to raising the existing impoundment, constructing a new slurry impoundment, constructing slurry cells, belt presses and others. This alternatives analysis was performed as part of a Section 404 permit for a valley fill and is currently being reviewed by the U. S. Army Corp of Engineers. All of the known possible alternatives were discussed in detail in the analysis. Due to the findings of the alternatives analysis, the company considers the engineered construction of the proposed impoundment to be the most favorable option of all the other alternatives evaluated, from both an economic and environmental standpoint. ALTERNATIVES EVALUATION FOR COALREFUSE/SLURRY DISPOSAL Background The company currently operates several deep mines and employ over 300 people and produces over 3.9 clean Mt/a (4 million stpy) of high quality, low sulfur coal. Currently, coarse refuse is belted to a valley fill, while, fine refuse is pumped to the existing impoundment. Coarse refuse is trucked to the existing impoundment as needed for construction purposes. The average recovery is approximately 50%; therefore, over 3.9 Mt/a (4 million stpy) of coal refuse must also be separated and placed.

Jan 1, 2003

By R. S. Ondrey, R. A. Haney, T Tomb, R. T. Stoltz, Novakowski D. L. Chiz, E. J. Gerbec, D. J. Atchinson

Although the number of operating longwalls in the United States (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and in some cases more than doubled. As a result of this production increase, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Methods being used to control dust were noted, with special emphasis placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control practices in place at the time of the visit to dust concentrations measured at the tail and on the tail shearer operator and to the average of all the dust concentration measurements from the occupations sampled. The methods used to control dust were also compared to the gamut of methods known to be available. This paper presents a discussion on the effectiveness of the methods being used to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1991

By Y. C. Kim

One-quarter of a century has passed since the "theory of regionalized variables" (geostatistics) was introduced by G. Matheron (1962, 1963) in France. Yet, only during the past decade has geostatistics found broad acceptance in the mining industry. Foremost among the reasons for this time lag was ignorance. The first English treatise on geostatistics was not written until Matheron (1971), and the first published text accessible to mining professionals did not appear until David (1977). Other significant reasons for the slow acceptance of geostatistics included the conservative nature of management in the 1970s minerals industry, and the fact that conventional ore reserve estimation performs reasonably well when confined to massive deposits of base metal and iron deposits having relatively low coefficients of variation in grades. In short, mine engineers and geologists were not willing to accept a new set of tools for problems that they did not see.

Jan 1, 1989

By J. C. Stankus, S. S. Peng

Many coal seams are associated with soft floor strata. During mine development, if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One method for controlling floor heave is floor bolting. This paper describes the demonstration of flour bolting methods in a West Virginia, info coal mine. Three methods were used: vertical full resin bolting, floor truss bolting and floor truss bolting pins a floor slot at the center of the entry. The design of each method and the experimental results are discussed.

Jan 1, 1995

By J. A. Herbst, Y. C. Lo

An attempt has been made to parameterize the population balance model for a ball mill based on measurements of the elementary breakage process obtained using an ultrafast load cell device. Detailed insight obtained concerning the fragmentation of particle assemblies with the ultrafast load cell leads to a better understanding of ball mill grinding. The ball mill breakage function and specific selection function are derived from an average single event representing the multiple breakage events which occur in ball mill grinding. Since both the breakage function and the specific selection function depend on the loading mode in the mill, predictions of breakage mechanisms in ball mills are possible by using data obtained in various elementary loading modes. The application of this model to the description of batch ball milling behavior has resulted in reasonably accurate predictions of product size distributions for various energy inputs.

Jan 1, 1992

By Stanley C. Suboleski

The increase in productivity which has been achieved in mining during the past two decades has been attained largely through the replacement of manpower with electrical power. Power demands should continue to increase, requiring electrical distribution systems to be well planned to avoid inadequate voltage levels caused by underdesign and excessive costs resulting from overdesign. To aid the mining electrical engineer in designing proposed power systems or analyzing changes to existing systems, a digital computer program has been developed. This program will analyze alternating or direct-current networks with up to 10 voltage sources, 75 loads and 300 total segments. A maximum of nine levels of voltage is permitted in the system. This project was part of a package of programs developed at Virginia Polytechnic Institute (WI) for the mining industry under sponsorship of the Office of Coal Research. Included in this package are also programs to: 1. Schedule mine production and predict cost of mining 2. Simulate rail haulage systems 3. Simulate belt haulage systems 4. Analyze ventilation networks 5. Analyze pumping networks These programs are available from the Department of Mining Engineering, VPI, Blacksburg, Virginia 24061 for a nominal processing cost.

Jan 1, 1970

By A. K. Bakshi

Mineral suspensions show Newtonian flow properties at lower solid concentration, but change into non-Newtonian regime as the solids content is increased. For Newtonian fluids viscosity is independent of shear rate, but for non-Newtonian fluids it varies with rate of shear. Therefore, measurement of viscosity at a shear rate, different from the process will be futile unless the slurry is Newtonian. This is especially true for hydrocyclone operation, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between viscosity and process efficiency. A new technique to distinguish such changes in flow type has been developed. This involved a co-axial cylinder type viscometer which measured apparent viscosity at a low shear rate, and a vibrating sphere type viscometer which measured the apparent viscosity at a high shear rate. Special precautions were taken to allow measurements of viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica of 80% passing 65~m size in water was used to prepare slurries at concentrations ranging from 1O-70wt% solids. Viscosity of each slurry sample was measured simultaneously by both the viscometers and the results were compared with each other. With this technique, it was found that all the silica slurry samples were in the Newtonian flow regime.

Jan 1, 1995

By S. R. Abt, J. D. Nelson, G. M. Smith

An empirical investigation was conducted to formulate a design criteria for predicting the beach profile of hydraulically deposited tailings. Field data were obtained from mining operations producing gold sulfides, silver, molybdenum, copper, platinum, and uranium. Site-specific parameters were collected that included the beach slopes, tailings soil properties, slurry properties, and the slurry distribution system characteristics. Each of the beach profiles were dimensionlessly plotted, and regression expressions were computed. It was determined that either a power expression or exponential expression closely predicted each beach slope. A general power expression and a general exponential ex¬pression were developed resulting in a design criteria. A procedure was formulated to determine which expression, power or exponential, is applicable to any specific site. A slope designation chart was developed as a function of the discharge, the tailings critical tractive shear stress, and the inertial forces exerted by the slurry on the beach.

Jan 1, 1987

By William D. Leech, Ronald E. Romley, Gary N. Sheppard

The Price Road Drainage Tunnel was constructed for the Arizona Department of Transportation (ADOT) in 1988 and 1989 to provide surface water drainage for the proposed outer Loop Highway (SR 117). The 5.4 km (3 mile) long, 6.6 m (22 ft) excavated diameter tunnel was driven through sand, gravel and cobbles utilizing an open face digger shield. Precast concrete segments were erected for initial ground support. A second-pass reinforced concrete final lining was placed, which was followed by contact grouting. This paper will consider the owner's representatives' view of the effectiveness of using precast concrete segments for this project. Topics discussed include segment design and erection, ground support, geotechnical instrumentation, segment erection verses contact grout interactions and tunnel production.

Jan 1, 1991

By Michael P. Connor, O&apos

The Wing Hill Garnet Deposit, located near Rangeley, Maine, forsed through assimilation of Early Paleozoic metasediments by an intrusive Devonian gabbro. The resulting ore body is exceptionally large and high-grade, consisting of 50-70% almandine garnet. Following open-pit quarrying, the ore is trucked to Industrial Garnet Extractives' mill in West Paris for final processing. Two grades of abrasive are produced - a pure, premium grade INDUSTRIAL GARNET and the Lower grade co-product IGE UTILITY GRIT, both of which are available in a variety of sizes. INDUSTRIAL GARNET is marketed world- wide into a diverse marketplace including both loose grain and bonded applications.

Jan 1, 1985

By Richard W. Patton

With the advent of the Clean Air Act and the installation of flue gas desulfurization (FGD) equipment (scrubbers) on coal fired power plants, the management of solid wastes has taken on added importance. Aside from the large amounts of fly ash and bottom ash usually generated, large quantities of liquids in the form of scrubber sludge are also produced. These wastes must be disposed of within the constraints of land and water quality regulations. This paper describes the practices adopted by the electric utility industry in denting with this problem, including methods of generation and treatment, quantities and characteristics of the materials, and transportation and disposal practices. The paper also briefly describes final product characteristics and several applications for commercial utilization and land reclamation.

Jan 1, 1983

By B. D. Nichols, W. S. Gregory

SOLA-DM is a three-dimensional finite-difference computer code designed to model the dynamics of an incompressible fluid and the transport of discrete particulate material around obstacles impervious to flow. The numerical methods used in this code are described. SOLA-DM was used to predict the particle flux sampled by the 10-mm Dorr-Oliver Cyclone and MINIRAM dust monitors. Various geometric and dynamic variations of monitor and airflow combinations were tested. The code predictions are shown in computer-generated graphic plots.

Jan 1, 1987

By J. Ludden

By Sims Some two years ago we began investigating low coke button bituminous coal for use at our Bound Brook, New Jersey plant as a replacement for anthracite. Since August, 1957 the plant has been operating continously on this coal with the exception of a new 200,000#/hr, cyclone boiler. This study was motivated not from our desire to conduct combustion research, but for the sole purpose of reducing our steam costs, The indications were that the economics were greatly in favor of the use of the bituminous coal. The attempts to reduce the costs have developed some knowledge that has enabled this program to succeed reasonably well as will be discussed later by Mr. Ludden. The production of steam size anthracite is dependent upon either the reclamation of old culm banks or the breakage in the production of the domestic sizes. The anthracite industry has not as yet been able to cut, its mining costs to the point where the production of steam sizes has become a profitable business. This has resulted in two basic problems: (1) A constantly rising price in an attempt to have those sizes carry their share of the cost and, (2) Periodic shortages of supply when the demand is good but the market price prohibits the mining of anthracite to produce those sizes only, These conditions have made the long range forecast appear as though the price would go even higher and/or the supply at times be critically short.

Jan 1, 1958

By Kenneth E. Merklin

The heavy media process is now being used extensively throughout the world for the gravity concentration of a great number of different minerals. The process is a commercial adaptation of the heavy liquid procedure which has been used in laboratories for many years to separate mineral of different specific gravities. In the heavy media process, a suspension of finely divided particles in water is used to increase the apparent specific weight of the fluid to the desired separating point. The original heavy media process used sand, galena, pyrite and occasionally other materials as the solid constituent of the separating suspensions. As the process developed, the need for a more universal media meeting the following requirements was recognized: 1. High specific gravity. 2. Resistance to abrasion. 3. Resistance to corrosion, 4. Readily reduced to a suitable size consist for suspension in water. 5. Available in quantity at economical price levels. 6. Easy to recover by a simple method.

Jan 1, 1958

By S. F. Hillis, J. E. Rourke, K. A. Szalay, O&apos

INTRODUCTION For the past 25 years, tunnel support requirements have frequently been determined, at least in North American practice, by classifying the rock according to the system proposed by Terzaghi (1), using one or more of the 8 Rock Conditions which he defined, the rock load then being selected within the range given for each Condition. However, there is a lack of published data comparing Terzaghi loads with actual measured rock loads, and it would appear that the degree of conservatism, or otherwise, of the Terzaghi approach is very often unknown. Excavation of 4 large diameter tunnels at the Tarbela Dam Project in Pakistan afforded an opportunity to compare Terzaghi and measured loads, through instrumentation of the steel ribs installed for temporary support, and by classification of the geology exposed during the tunnelling operations. In addition, the deformation of the rock surrounding the tunnels was monitored during excavation by means of borehole extensometers installed prior to the start of tunnelling. This paper describes the tunnel instrumentation and the results obtained therefrom, and relates these results to the Terzaghi load coefficients. It also discusses the effects of the methods of excavating the tunnels on the rock loads and rock deformations. PROJECT DESCRIPTION The Tarbela Dam Project is located on the Indus River in

Jan 1, 1974

By E. Woodburn, Harrison R. Cooper, R. Putman

The key to concentrator automation is practical means for obtaining continuous assay data from concentrator streams. The technique most successfully used is x-ray fluorescence analysis. The practical reality of on-stream x-ray analysis has been achieved through effort over the past twenty years, marked by an occasional breakthrough, but more typically a step-by-step development to which many individuals and organizations have contributed. The net result of this progress is the present capability to install on-stream x-ray analyzer systems on a turn-key basis. It is now possible to provide all components of an x-ray analysis system as a completely engineered unit which can be put into immediate use, minimizing needs for specialized application know- ledge to benefit from continuous assaying in process control. The economic factors which influence the choice of system and limitations of the x-ray fluorescence technique for slurry analysis are reviewed.

Jan 1, 1976

By G. Récoché

For the African continent promoting a sustainable utilization of its mineral resources could be considered as a key determinant to fight against poverty. Sustainable development performance indicators for measuring the economic, environmental and social impacts of mining activity are necessary for drawing up policies and sectoral actions, identifying and controlling risks, identifying and implementing sustainable development actions, negotiating between stake-holders, improving mine production, etc. To respond to this need, the SIGAfrique Network proposed to develop a joint decision support tool entitled the African Mining Observatory (AMO) and, to this end, develops a system of indicators to be integrated within the SIGAfrique database. The development of both the OMA and the indicators is based on a participatory method within the working groups, which comprise experts/participants from the 13 SIGAfrique partner and observer countries (Guinea, Burkina Faso, Mali, Tanzania, Niger, Mozambique, Kenya, Uganda, Senegal, Angola, Madagascar, Ethiopia, and Mauritania).

Jan 1, 2007

By S. Fairis Samuelson

Boling Dome. a piercement salt dome in the Texas Gulf Coast basin is (was) the single largest deposit of native sulfur in the Western world. Total sulfur production has been over 81.000,000 long tons and the mine is still in production. Data from over 60 years of operation and 8.000+ wells reveal a salt dome rich in history as well as minerals. Sulfur mineralization and production correlate well with caprock structure and morphology. The occurrence of Mississippi Valley-type deposits in fracture zones is notable in some areas and may warrant additional study. DISCOVERY AND PRODUCTION HISTORY Boling Dome is located in the south- east corner of Wharton County, Texas, 60 miles south-west of Houston. It is a piercement type dome in the Houston diapir province. It was discovered in 1922 when the county surveyor noticed sour gas seeps along the San Bernard River (Haynes. 1942). Several companies including Gulf Production Company. Humble, Texas Company, Sun and others quickly began drilling for oil and gas. Traces of native sulfur were reported in cuttings from many wells penetrating the caprock, but the first commercial quantities of sulfur were not found until Gulf Production's E.M. Chase 3 and 4 wells were drilled in 1927. Texas Gulf Sulphur, then mining sulfur at Gulf Dome in Matagorda County, secured the sulfur rights from Gulf for $3 million in cash and half of the profits after expenses for development and construction of plant and townsite were met (Haynes, 1942). The drilling results from 200 or so Wells revealed a massive deposit destined to become the largest single source of native sulfur in North America. Original reserves were estimated at just over 46 million long tons and were increased in later years. Production by the Frasch method was begun by Union Sulphur in 1928, and continued by Texas Gulf Sulphur Co. in 1929, and Duval Sulphur Co. and the Baker Williams Co. in 1935. Union produced 8,009 long tons, Duval produced 571,123 long tons, and Baker Williams produced 1,453 long tons. Through its deal with Gulf, Texasgulf acquired the largest and best mineralized portion of the dome and has produced 88,544,466 long tons through 1990, and production is planned for several more years. That amount of sulfur is equivalent to a cube measuring 1,152 feet on each side, or a sulfur highway 1 foot thick, 20 feet wide and 14,479 miles long. Peak production averaged 8,376 ltpd in 1948. A price war between North American sulfur producers and Mexican sulfur producers in 1956, followed by the recession of 1957 and 1958 (Haynes, 1959) coupled with a rapid increase in mining depth to below 700 feet began a gradual production decline that was never reversed (Figures 1 and 2).

Jan 1, 1992

By Robert C. Bates

Background is given on the various equations used to describe diffusion and convective flow of radon in porous media. Bureau-developed equations for modeling diffusion and Darcy flow through multilayered porous media are described briefly, and examples of their use are given. Analysis results discussed include: The transient effect of pressure changes in different length models, time dependent flux changes in multi-layered models, and radon flux through pinholes in sealants

Jan 1, 1980

By N. Gritzuk

The area of Canada with which we are here concerned consists of Yukon Territory and Northern British Columbia. Generally it lies west of the coastal mountain range and access to the sea can be gained at only selected points which are relatively few. It is served by the Alaska Highway as well as a provincial and territorial system of roads permitting transport of mining products to Whitehorse in Yukon Territory. This town it the northern terminus of the White Pass and Yukon Route, which system provides a rail service between Whitehorse and Skagway, Alaska a distance of 110 miles, and thence to Vancouver, British Columbia, by the coastal Motor Vessel C. J. Rogers, a distance of an additional 890 miles. At present the service between Vancouver, B.C. and Whitehorse, Y. T. is on a fourteen day basis. The coastal vessel, capable of carrying 3,200 tons of cargo, was specially designed and built in 1955 for handling containerized cargo and general cargo northbound, and containerized and palletized asbestos fibre, and palletized lead and zinc concentrates southbound.

Jan 1, 1961