Search Documents

By T. J. Lutz, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Of the in-use RAs, over 95% are mobile RAs with the remainder being built-in-place (BIP) RAs. Heat/humidity buildup has been one of the major concerns with mobile RAs. For BIP RAs, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP RAs, the National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP RA with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated, or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP RA. The results show that the air supplied to a BIP RA may require heating and cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 70°F and a humidity that reached 90 %RH, providing 55°F dew point air was able to keep the internal apparent temperature below the mandated 95°F. Results for each test case are presented. INTRODUCTION The Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines since 2008 [1]. MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. In its 2006 report, the West Virginia Mine Safety Technology Task Force recommended an apparent temperature limit of 95°F for RAs [2]. In 30 CFR 7.504, MSHA specifies a maximum apparent temperature of 95°F inside an occupied RA [3]. The apparent temperature is calculated using both air temperature and relative humidity [4]. To determine if their RAs meet the apparent temperature limit, RA manufacturers have been performing 96-hour-long heat and humidity tests in laboratories. During these tests, a heat input of 117 W (400 BTU/hr) per person is used to represent the metabolic heat of a single miner [2]. The heat generated by the RA’s carbon dioxide system is also accounted for in testing. To account for this heat, 50 W (170 BTU/hr) of heat per miner is used for a lithium hydroxide scrubbing system, or 30 W (100 BTU/hr) of heat per miner is used for a soda lime scrubbing system [5]. In these tests, air velocities around the RA are minimized to represent the worst-case scenario of an interruption in mine ventilation that might occur in a mine disaster."

Jan 1, 2017

By V. N. Kolesnikov

The Sikhote-Alin part of the Circum-Pacific Ore Belt is characterized by wide distribution of Sn, Pb, Zn, W; Au, Ag, and other mineralization. This mineralization is regionally associated with the Late Cretaceous-Tertiary East Sikhote-Alin volcanic belt where it overlaps the Taukha accretiollary-wedge terrane of the Early Cretaceous age. The Pb-Zn deposits of the Dalnegorsk ore district may be grouped into the skarn (about 80%) and vein types. The skarn deposits are of major commercial value. Their geological position is controlled by the carbonate units located within tectonic melange of the Taukha terrane. Some other lithological and tectonic factors also play a significant role ill distribution of the mineralization. The ore bodies are traced to the depth of 1000-1500 m below the surface, having a pipe-lens shape and vertical zonation. Major minerals of the ores are galena, sphalerite, pyrrhotine, chalkopyrite, hedenbergite, quartz, and calcite. The minor elements of the Pb-Zn mineralization are cadmium, silver, bismuth, and copper. The paper describes relationships between mineral suites and minor element contents in the ores, as well as their significance for processing the ores. The metallurgy applied allows high recovering of the major components (Pb -93.9%; Zn -91.4%). However the tails contain some minor components that may be of commercial interest.

Jan 1, 1998

By Jeff W. Butwell

Mill flotation tailings impounded at the Gooseberry Mine site between 1976 and 1984 were determined to be an economic source of gold and silver. The tailings would be recoverable by standard heap leach technology in conjunction with feed agglomeration. Metal recovery at 85% gold and 75% silver is attained on properly agglomerated (pelletized) tailings that average 85% -75 µm (-200 mesh). The impounded tailings averaged more than 18% moisture (32% moisture maximum at depth) in place behind the storage dam. Therefore, the mining method, mixing and agglomeration technique, and materials handling practice were major considerations in making this operation a financial success. The Gooseberry Tailings Project is located about 35 km (22 miles) east of Sparks, NV. The project is owned by Asamera Minerals (US) Inc. The company's Western Nevada Gold prop¬erty surrounds the Gooseberry Mine by several miles on all sides. Gold and silver mineralization at the Gooseberry Mine is restricted to a narrow calcite-quartz vein. Calcite makes up more than 80% of the vein throughout the mine. The host rock consists of porphyritic andesites and dacites constituting volcanic flows. The rocks are propylitized or silicified to a varying degree. This ore mineralogy, then, also describes the tailings processed by heap leaching. The Gooseberry tailings were auger sampled in 1983 and again in 1987 after a final lift of 109 kt (120,000 st) was deposited in 1983 and 1984. The total volume behind the dam was calculated from planimeter measurements from tailings surface to original area topography.

Jan 1, 1990

By P. J. Ryan

December 1988, Phelps Dodge Corp. brought an underground gold mine into production in the republic of Botswana. The mineralization is associated with steeply dipping shear zones in Archean greenstones of the Tati schist belt. The gold is intimately associated with sulfides and is refractory in nature. The deposit is being exploited by underhand open stoping methods. Vertical and inclined shafts are used to hoist the ore to the surface where it is treated by conventional crushing, milling, and flotation, followed by fluid bed roasting with cip elution and carbon regeneration. Adjacent deposits are being explored with a view to increasing production. Legal and taxation aspects of operating in Botswana are discussed.

Jan 1, 1991

By André Vervoort

The roof behaviour in room and pillar panels during the development of roadways and the subsequent pillar extraction was monitored underground and numerical simulations were conducted. For several underground sites, a satisfactory, correlation was found between underground measurements and three-dimensional numerical simulations using a boundary element code in the linear elastic domain. However, to simulate bed separation, and roof block collapses more complex models were required, of which examples are presented.

Jan 1, 1992

By M. R. Peterson

The U.S. Bureau of Mines has investigated new methods for increasing the selectivity in flotation by creating and regulating reagent concentration gradients within flotation columns at steady-state operation. Gradients were generated and traced in a water-only system with the use of fluorescent dyes, and the effects of various operating parameters on these gradients were investigated. From this investigation, it was found that both gradual and steep gradients could be generated in the froth cleaning zone, and that these gradients could be changed through the manipulation of both physical and chemical operating parameters. The application of reagent-gradient control to mineral systems could improve both flotation grade and recovery in commercial flotation operations without the use of additional flotation circuitry.

Jan 1, 1992

By Tuncel M. Yegulalp

In this paper we revisit the well known "Ultimate Pit Limit Problem" and suggest an alternative approach for fast and efficient solution. We follow the approach originally proposed by Johnson and Barnes (1988), but utilize the "Excess Scaling Algorithm" in solving the equivalent maximum flow problem. This algorithm provides significant increases in speed and reduction in memory requirements over the well known Labeling Algorithm of Ford and Fulkerson (1956), enabling one to solve large problems with relatively small computers. We present results of a series: of benchmark tests using this approach against the well known Lerchs Grossman algorithm as well as a brief description of the new algorithm.

Jan 1, 1992

By D. Hodouin

Abstract. Dynamic experiments were performed in a continuous open-circuit 40x40 cm ball mill using a pseudo-random binary sequence of the feed rate and measuring the variations of the discharge particle-size distribution. The impulse response is calculated by a cross-correlation technique. Then a model involving a discrete transfer function and a time-series stochastic equation is calibrated using maximum likelihood methods. Based on this empirical model. a minimum variance controller with constrained input is designed and its performances are compared. by simulation, to the performances of a conventional PID regulator.

Jan 1, 1987

By Judson C. Higgins

The paper addresses changes in surface transportation methods in the Industrial Minerals business starting with history, the changes to present time including such areas as energy costs, improved highways, changes in regulations and deregulation, and attempts to project future transportation trends. Transportation methods such as rail, piggyback, truck and barge are compared, and their impact on Industrial Minerals producer's costs and profits examined. The customer impact on our businesses due to deregulation is also discussed.

Jan 1, 1983

By Dr. David R. Hargis

Finite-difference digital computer models can be used to evaluate the effects of proposed mine dewatering and depressuring operations on ground-water aquifer systems. The effects of proposed dewatering and depressuring operations can be simulated for both underground and open-pit mining in confined and unconfined aquifer systems. Design of dewatering and depressuring well arrays to accommodate proposed mining operations in a variety of hydrogeologic settings can be accomplished through judicious application of well-documented and tested computer programs that are widely available from government agencies and universities. The speed and flexibility of the computer models can provide an economical means for comparison of alternative mining plans, and can be used to determine the optimum mine plan with respect to dewatering requirements.

Jan 1, 1980

By A. B. Seal, C. J. Bise

Excessive noise has long been a hazard in the coal-mining industry. Studies conducted during the mid-1970s and mid-1990s consistently show that hearing loss within the mining industry persists, in spite of regulatory requirements and sampling technology advances. When the U.S. Mine Safety and Health Administration's new health standards to protect miners from hearing loss took effect in September 2000, the potential developed to reevaluate sampling approaches with regard to noise-source hazards, such as task-based methods. This paper describes results from a Pennsylvania State University research project now being conducted at an underground coal mine. Each occupation was reviewed, and a list of tasks or processes performed by each was generated. Traditional personal noise dosimetry, static sound pressure levels and equipment sound mappings have been performed. Job tasks indicating the greatest levels of daily noise exposure and contributions to noise dose have been identified and will be discussed.

Jan 1, 2003

By S. J. Porter, M. T. McRae

The new tunnel at Genting Sempah is part of a privately funded infrastructure projectthat involves duplicating the existing highway extending from the Gombok Toll Plaza near Kuala Lumpur to Karak, in Malaysia. The 60 km long tollway includes an 800 m long, two-lane highway tunnel with excavated dimensions of 10.5 m wide by 8 m high. The majority of the tunnel extends through slightly to moderately weathered, moderately to highly jointed quartz porphyry. Excavation of the tunnel was performed using drill and blast methods and the primary tunnel support consists of rock dowels and shotcrete except for short sections adjacent to the portals where steel sets were utilized. A portion of the tunnel encountered sheared and altered material that was successfully supported using rock dowels and shotcrete. The final lining for the tunnel consists of mesh and fiber reinforced shotcrete. The flexible nature of the primary support and shotcrete final lining resulted in considerable cost savings and expedient construction methods.

Jan 1, 1997

By Laura McNally

In 2006, McNally International Inc., in a joint venture partner-ship with Aecon Constructors, was the successful bidder on two York Region Tunnel Projects: the Bathurst Collector/Langstaff Trunk Sewers and the York Durham Sewer System (YDSS) Interceptor Sewer 19th Avenue, both in the Toronto area. These projects comprised a total of 13 km (8 miles) of 2.74 m (9 ft) finished diameter tunnels and are both part of the YDSS. Both contracts required the use of earth pressure balance (EPB) tunnel boring machines (TBM) with a precast concrete segmental liner.

Jan 1, 2008

By Gui DeReamer

Located on the Wabash River in the central portion of the state, the city of Lafayette, IN is relatively small compared to most cit-ies that incorporate tunnels into their combined sewer overflow (CSO) systems. The original CSO plan for the city was to replace two aging lift stations that were built in the 1950s. The original con-cept was to build a new sewer using conventional cut-and-cover construction to eliminate one of the lift stations ? the Parking Lot Lift Station ? and build a new regionalized one at the location of the Pearl River Lift Station. The initial sewer design was sized just to handle the flow that would eliminate the Parking Lot Lift Station. The planning for this project was being developed as part of the city?s CSO long-term control plan (LTCP) that focused on reducing the overflows from the city?s 14 overflow points. However, during the development of the CSO LTCP, a major industrial user indicated it would be increasing its flows to the system, which required additional conveyance capacity to meet the city?s CSO LTCP. After reviewing the design concepts with city representatives during the planning phase of the project, the mayor indicated that he wanted to minimize impacts to downtown businesses; therefore, trenchless alternatives were considered. The last piece of the puzzle that drove the project away from a small diameter pipeline was discovered during a flow monitoring program to collect flow data for the CSO LTCP project. This study revealed a major restriction in the 100-year-old Pearl River Trunk Sewer, located beneath four active railroad tracks. To eliminate this flow restriction, provide more overflow storage and reduce the impact to local businesses, a new 2.7- to 3.6-m- (9- to 12-ft-) diameter tunnel sewer became the most viable solution.

Jan 1, 2011

By T. J. Lutz, J. L. Carr, J. A. Yonkey, C. C. Jobes

"Since 1984, the date of the first recorded fatality involving a remote controlled continuous mining machine, 38 miners in the United States have been killed when they were struck by a continuous mining machine. Proximity detection is a valuable tool for preventing fatalities, and the use of these systems is expected to significantly improve safety. Proximity detection provides a means to prevent accidents like these. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a series of underground tests to evaluate the accuracy and repeatability of proximity detection systems under a number of conditions such as varying the orientation and height of the personal wearable device (PWD), moving the PWD close to the trailing cable, and activating the machine’s mining mode. At the 2014 SME Annual Meeting, results from tests on first-generation proximity detection systems were presented. This paper will provide results from the similar tests performed with second-generation systems. The results show that performance has improved. For example, the negative impact of PWD orientation and the trailing cable has been reduced. However, some inconsistencies remain. Notably, performance changes dramatically when mining mode is activated. INTRODUCTION Since 1984 there have been 38 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM) [1]. In August 2011, the Mine Safety and Health Administration (MSHA) published a proposed regulation that would require proximity detection systems on all continuous mining machines except full-face machines [2]. Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHA-approved proximity detection systems are commercially available. MSHA estimates that of the 38 fatal striking and pinning accidents that have occurred since 1984 involving CMMs, the use of proximity detection could have been a preventative factor in at least 28 cases [1]. Furthermore, MSHA estimates that proximity detection could prevent 20% of all deaths throughout the industry [3]. NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system [4] and have recently conducted research intended to develop more advanced proximity detection technology for CMMs [5,6,7,8]. In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate [9,10] and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators [11,12]."

Jan 1, 2015

By P. R. A. Andrews

Areas of bubble contact were delineated for topaz and tourmaline in the presence of chloride, fluoride, sulfate, phosphate, oxalate, and citrate ions using dodecylamine hydrochloride collector. The limits of pH and the minimum collector concentration were established using the bubble pick-up technique. Bubble contact did not occur below the p.z.c. (point of zero charge), estimated to be 5.6 for topaz and 6.6 for tourmaline, in the presence of chloride ion. Flotation below the p.z.c. was, however, extended by citrate, oxalate, phosphate, sulfate, and fluoride ions. Oxalate, citrate, and fluoride ions displayed the greatest pH range of activation, followed by phosphate and sulfate ions. Chloride ion acted as an indifferent electrolyte. Topaz was selectively activated with respect to tourmaline by fluoride and phosphate ions. Topaz was activated by fluoride ion between pH 2.4 and 5.6. Tourmaline flotation in this pH range was virtually insignificant. Topaz was activated by phosphate ion between pH 4.9 and 7.4. Tourmaline flotation in this pH range was only partial. Activation appeared to be strongest when anionic protonated species were in maximum concentration. Strong activation also corresponded to very stable metal ion species thought to be formed on the surface of each mineral.

Jan 1, 1991

By K. V. Raj, M. McNinch, A. L. Miller, J. Wilson, D. A. Parks

Diesel particulate matter (DPM) has been shown to contribute to various adverse health effects on underground miners. In order to reduce worker exposures, it is critical to measure the levels of DPM in the active work settings and in real time. However, the 5040 method, developed by the National Institute for Occupational Safety and Health (NIOSH), which quantifies the mass of elemental carbon (EC) and organic carbon (OC) in the samples, is based on full-shift samples, and can take days or even weeks for results. Use of real-time monitors could significantly reduce the risk of DPM exposure to miners, and available monitors have been shown to quantify DPM, mainly using the EC and other surrogates. The NIOSH Spokane Mining Research Division is conducting research aimed at developing a field-portable DPM monitor that is able to quantify both EC and OC. One part of this work is to understand the effect of OC on currently available real-time DPM monitors. This paper will present the results from experiments that were designed to observe the effect of OC on real time monitors and compare the results with the NIOSH 5040 method. BACKGROUND Diesel engines remain ubiquitous in mining environments and, as such, are one of the primary sources of ultrafine- and nano-aerosols in the mining environment in the form of diesel particulate matter (DPM). As a result of their small size, DPM has longer residence times in a mine atmosphere than the typically larger mechanically generated dust [1]. In addition, the small size enables DPM to penetrate deeply into the respiratory system [1], and exposure to DPM has been shown to contribute to various adverse health outcomes of the pulmonary system [2] and cardiovascular system [3]. Diesel exhaust has been classified as a carcinogen to humans (Group 1) by the International Agency for Research on Cancer [4]. Due to mounting concern about adverse health outcomes, extensive efforts are being made to reduce workers’ exposure to DPM, with the high exposures that often occur in underground mines being of particular concern [5]. New technologies are being developed to reduce engine emissions and thereby airborne DPM levels, including advanced engine technologies, a host of aftertreatment systems [6], and a variety of alternative fuels. The latter have been shown to markedly decrease respirable DPM and other hazardous components of diesel emissions from mining vehicles [7], yet high exposures persist, especially in underground mines [8]. In order to reduce worker exposures, it is critical to measure the levels of DPM in active work settings. In mine settings, exposures to DPM are measured by collecting air samples on filters (usually full-shift samples) and sending them to a lab for analysis using the Mine Safety and Health Administration (MSHA) P13 method, a variant of the National Institute for Occupational Safety and Health (NIOSH) 5040 method. The 5040 method is designed to quantify the mass of elemental carbon (EC) and organic carbon (OC) on the samples [9], which is then used to determine the concentration in the sampled air. MSHA has set a limit for exposure, which is based on the concentration of total carbon (TC), or the sum of both EC and OC. The allowable TC in the air (time-weighted average over the shift) is 160 μg/m3 of TC [10].

Jan 1, 2019

By K. N. Han

Coal is becoming increasingly important as a major energy source in the face of the world's depleting energy mainly based on oil reserves. Coal is by far the most abundant fossil fuel both in the United States and abroad. Currently, because of increased mine mechanization, the fineness of preparation plant feed is increasing. Further, in the future as the grade of coal diminishes and the sulfur content increases, upgrading preparation of coal is very important. Because the density of coal is less than that of rock materials that occur as impurities, coal is separated from such waste largely by gravity-controlled processes for particle size between 5 inches and 28 mesh. If the size of coal particles is below 28 mesh, froth flotation is a good method for upgrading fine coal. Previously, numerous investigators have tried to upgrade coal values by froth flotation(1-16) and have achieved moderate success. However, the recovery and grade of coals in the concentrates are not always satisfactory, especially when the particle size is small. In general, when the size of coal is below 100 mesh, the above methods suffer from poor grade and low recovery. The reason for this is that as size decreases, the effects of gravity diminish, and other forces take effect.

Jan 1, 1985

By Frank E. Dalton

BACKGROUND OF TARP The first settlement in Chicago in the 1830's was only 0.61 m (2 ft) above the level of Lake Michigan. The area was flat and swampy with local streams and rivers generally flowing to Lake Michigan. Repeated outbreaks of cholera and typhoid fever in the middle and late 1800's led to the reversal of the river system (away from Lake Michigan to the Mississippi River). As a result of this reversal, the Chicagoland area has had to restrict water withdrawals from Lake Michigan and has had to develop and implement water management programs in compliance with orders set down by the Supreme Court of the United States. In order to comply with restricted lake diversion requirements and to compensate for a natural setting which was essentially hostile to human habitation, it has been necessary to embark on the construction of massive public works which include the world's largest water filtration plants, the world's largest wastewater treatment plants and finally the construction of TARP. The rivers and streams in the Chicago area are the headwaters of the Illinois waterway system. These headwaters are heavily polluted from combined sewer overflows of the area. Present pollution control laws require that combined sewer overflows be eliminated so that the rivers and streams can be used by the citizens of Cook, Du Page and Will Counties and other downstream communities. Fifty-three of the older most densely populated communities including the City of Chicago, covering an area of 971 sq km (375 sq miles), are served by combined sewers. Combined sewers carry both raw sewage and stormwater. Because porous ground surfaces have been covered 1815

Jan 1, 1979

By Steve Kral

The success of the industrial minerals end of the mining industry is often overshadowed by the high price of copper, the glamour of gold, and the nation's huge reserves of coal. Those three segments of the industry, however, along with every other business in the world, could not function without the products that are composed of a variety of industrial minerals. And, according to Haydn H. Murray, past president of SME, the value of industrial minerals in the United States is more than triple that of metals, about $19 billion a year versus $6 billion. In the developed countries of the world, he said, the value of industrial minerals is nearly always greater than the value of metallic minerals. Murray, also a professor of geology at Indiana University, was the luncheon speaker at the SME-sponsored Grinding of Industrial Minerals conference held in Asheville, NC this past September. Producers of industrial minerals know they must squeeze the maximum value out of the industrial mineral being mined and processed, Murray told the audience of about 100 people. Grinding and particle size, then, are vital to a commodity's profitability.

Jan 1, 1990