Search Documents

By L. Max Scott

[INTRODUCTION] The significance of gamma exposure to uranium miners has been recognized only in the last few years. Most ore deposits which have been underground mined, were 1% or less U308. Full-time mining of this grade ore can result in exposure exceeding 1 Rem per year. Several companies in Saskatchewan are planning to mine recently discovered ore bodies which contain ore pods in excess of 10% U308. The purpose of this paper is to present dose data which can be used to estimate gamma exposure from high-grade ore deposits, and to present mining techniques which will minimize miner exposure. [Dose Estimates] When one has a point source of radiation, the conventional laws of isotropic emission and the fall of dose with square of the distance, make dose calculations relatively easy. However, if one has an area source of infinite thickness, the assumption must be made that a uniform gamma flux is being emitted from all faces of the source (Figure 1). Dose from gamma emission would fall off only due to air attenuation up to such a distance at which the source can be considered to be a point source (usually 10 times the largest dimension of the source). For short distances, such as to the cab of ore-moving equipment, the dose reduction would be negligible. Assumptions: 1) Radium and gamma-emitting daughters are in secular equilibrium with uranium. 2) All gamma radiation is emitted from radium and its daughters. 3) Average gamma energy of 0.8 MeV. 4) Uranium ore has a linear attenuation coefficient of 0.212 cm-1, similar to that of Si02(sand). 5) Uranium ore density of 3.0 gm/cm3. 6) One curie of radium emits 6.84 x 1010 photon/sec(l). 7) One percent uranium ore contains 1 x 10-8 Ci/cm3 of radium. 8) Each MeV of 0.8 MeV photon results in a dose of 2.10[ ]10-3 mRem/hr. per MeV/cm2 -sec. 1) 9) Minimum ore depth 100 cm. 10) Linear attenuation coefficient instant for radium gamma of 0.374 cm -1 [ ] The photon flux from a radioactive slab is computed as follows: [Flux = photon/cm3 3(1) 2u S] [where, us is the linear absorption coefficient of s the source (uranium ore).] Thus, 1% uranium ore, in the form of an infinite slab, emits 1613 photon/cm2-sec, which results in a dose rate of 2.71 mRem/hr. Since the dose from an infinite slab is the same as a dose from an infinite radius right circular cylinder, the only correction needed from the above dose rate is for finite radius and point of dose above the end of the cylinder (Figure 2) [Dose = mRem/hr. {E2(bl) - E2(b3) - [(E2(b1sec[E] -E2(b3sec[E]]cos[O](1)]

Jan 1, 1981

By M. M. Botz

Cyanidation tailings which are disposed in a surface impoundment experience a loss of cyanide due to natural degradation, frequently reducing the cyanide concentration to very low levels. Quantifying cyanide losses in terms of pond geometry, local weather conditions and feed solution chemistry has been largely empirical though in many cases mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or an effluent limitation. To permit a more quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, WAD and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared against data collected for a North American tailings impoundment during 1998.

Jan 1, 1999

By David G. Abbott, Frank Coluccio

This paper will discuss the construction of nearly 165 m (540 ft) of 3.5. m (138 in) o.d. reinforced concrete pipe to replace an existing utilidor under the Duwamish River in Seattle, Wash. The project required that two 27.4 m (90 ft) deep shafts be installed for use as jacking and reception shafts during the tunneling operation, and permanent vaults once completed. Soil conditions to be excavated consisted of soft saturated sand and silt with a 21.3 m (70 ft) water head. This required the shafts to be constructed using ground freezing techniques and the tunnel installed by pipe jacking, using a Mechanical Earth Pressure Counter Balance (MEPCB) slurry shield. The original utilidor was constructed between 1924 and 1925, and has since been deliberately flooded because it is considered to be structurally unsound.

Jan 1, 1995

By Enrique Llewellyn

North River Energy Company a previous subsidiary of Republic Steel Corporation commenced development of the Number One Mine in mid-1972. The mine is located in West Alabama and presently employs a total of 632 people. Production capabilities have increased to 1.4 million clean tons of steam coal per year with the newly purchased Longwall System. Washer recovery averages 57 percent. The seam being mined is the Pratt or Corona with an average height of 52 inches and an average cover of 540 feet. The immediate roof is laminated sandstone and the floor is composed of a hard fireclay. Total production out of the mine is provided to Alabama Power Company under a longtime contract.

Jan 1, 1981

By John W. Brauns

18.1-RAILROAD JOHN W. BRAUNS Conventional railroad haulage can be employed at both open-pit or strip and underground mines-in the latter case, largely for transfer of ore from distant openings to processing plants, or processed material to loading points or docks, using standard hopper cars for bottom unloading or gondolas for rotary dumping. The major application, however, is in surface mining for moving ore and/or waste out of the pit to a crushing plant or dump. Consequently, the following will deal largely with this phase of railroad operation, though the conclusions apply equally, for the most part, to other rail-type surface haulage. In surface mining, trains consisting of a locomotive and gondola or side-dump cars suitable for loading by power shovels are used. Gondolas are restricted to hauling ore as a rotary dumper is required. Side-dump cars are more versatile, carrying both ore and waste, but because of their additional dumping mechanism they are likely to be more expensive to maintain.' Also they weigh up to twice a flat-bottom car of the same capacity and. therefore, fewer" cars can be hauled per train. Standard-gage track is most commonly used. Track systems incorporate low-quality temporary track where moves are frequent and permanent high-quality track on main lines. Rail haulage can be used alone, or in combination with other surface haulage methods, thus permitting a selection best adapted to the peculiar requirements of each mining project. 18.1.1---GENERAL APPLICABILITY, CONTROLLING PHYSICAL CONDITIONS For handling rough rock, the shovel-train system is unexcelled.' The ideal applica¬tion is in a large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported over 3 mi. If. in addition, a high production rate is to he maintained, railroad haulage probably will afford a lower cost per ton transported. Grade must he relatively gentle-usually 3% uphill and 4% downhill. The greater the differences in elevation involved, the greater are the track grade space requirements; for example, a 3 c ramp out of a pit only 300 ft deep is almost 2 mi long. Main-line track locations should he selected carefully so that the number of moves during the life of the mining operation can he kept to a minimum. This applies both to the ore haulageway and that for waste. Such moves are not only expensive, but are difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semipermanent trackage. Figs. 18-1 and 18-2 illustrate typical track layouts. The effect of terrain in considering railroad haulage is confined chiefly to the initial cost of the installation. Grade construction in mountainous territory is ap¬preciably more expensive. However, if that expense can be borne, the subsequent maintenance cost of trackage will not he much higher than in areas of low relief.

Jan 1, 1973

By M. I. Al-Wakeel

Nile sediment was collected as a waste from one of the water treatment plants in Cairo, and subjected to petrographical investigation and granulometric, chemical, and mineralogical analyses. It was expected to find diatomite in that sediment but it was a surprise to find that the diatomite content amounted to about 52.01% by volume in addition to quartz, orthoclase and clay minerals. The latter are represented by montmorillonite and illite minerals. The sediment is light gray in color, soft and has low density and high surface area, such density and surface area generally decrease with temperature. The sediment absorbs 317% of its weight in water. The diatomite skeletons are the main factor responsible for its high porosity producing microporosity and low density, and these particles are concentrated in the very fine silt size fraction (11x2µm). The common diatoms in such sediment include Cyclotella ocellata Pant, and Melosira granulata (Ehr.) Ralfs. It seems that this Nile diatomaceous sediment has many advantages over the fossil diatomite, such as Fayium diatomite in Egypt, with the absence of carbonate minerals that require grinding and calcination those cause destruction of the cellular structure and energy consumption. This Nile diatomaceous sediment can be processed using sequential classification to obtain diatomite concentrate of 88.8% grade at 90.6% recovery, and a middling product of 19.4% grade and 5.8% recovery. The suggested flow sheet is quite simple to produce diatomite product for different industries at a low cost. The unusual particulate structure and chemical inertness make diatomite an ideal mineral to be used as functional filler in a wide range of industries, and as catalyst carriers and insulating material. Key words: Egypt, Nile sediment, Diatomite, Beneficiation, Sedimentation, Classification.

Jan 1, 2008

By Jaye Pickarts, Bret Boster, Jack McPartland

Pegasus Minera de Chile, Ltda. is completing three phases of metallurgical evaluation on the Pullalli project to develop a preliminary process flowsheet. A project feasibility study is in progress. The feasibility study includes a proposed process flowsheet designed based on results from the multiple stages of metallurgical evaluation. Phases I and II of metallurgical evaluation included laboratory scale heap leach and milling cyanidation testwork on multiple drill core composites and bulk ore samples from the Pullalli Project. Phase Ill included pilot scale milling/cyanidation testwork on Pullalli drill core composites. The proposed flowsheet includes selective mining and separate processing of low grade and high grade ores. Low grade ore will be crushed and heap leached. High grade ore will be milled leached for 12 hours in an agitated cyanidation circuit. After 12 hours of leaching, sands and slimes will be separated and the sands will be washed using a counter current cyclone (CCC) circuit. Partially leached and washed sands will be added to the crushed low grade ore for heap leaching treatment and permanent placement. Partially leached slimes will be thickened in a high capacity thickener and will be processed in a CIP circuit. Leached slimes will be placed in a tailings impoundment.

Jan 1, 1996

By M. M. Poulton

Universities are not immune from the large number of retirements facing the mining industry. Department heads anticipate that we will need to replace all of the senior mining engineering faculty in the U.S. by 2020. Long term studies of Ph.D. completion times and success rates indicate that in Engineering disciplines in the U.S., the ten year completion rate is 65% at best and the four year completion rate is less than 8%. We do not have accurate data on completion rates and times for mining or metallurgical engineering Ph.D. students in the U.S. but students self-report their expected completion times are around 4 years. National data on doctoral students indicate that younger, full time students with sufficient financial support have a higher probability of success in completing their degrees in a timely manner. Students in Eastern U.S. mining engineering programs are on average 32 years old, 85% are full time, and the gap between support and cost of attendance is $5,000 per year. Students in Western U.S. programs are on average 38 years old, 78% are full time, and the financial gap is $8,483. Further, it appears that domestic graduate students are not very geographically mobile. The current demand for new faculty is higher in Western programs but the longer term retirements are higher in Eastern programs. While all Ph.D. students who responded to the 2010 survey indicated an interest in a faculty position at some point in their careers, very few were applying for the open positions. Over the past 35 years for which data could be obtained, the maximum number of Ph.D. students enrolled in mining engineering in the U.S. is 115 with a maximum of 27 degrees granted in one year. On average 89 students are enrolled in doctoral programs in mining engineering in the U.S. with average degree production of 15 Ph.D.s per year.

Jan 1, 2012

By K. Chandrasekaran

Carbon-in-leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. The CIL process is becoming attractive even in other situations when preg robbing is not a factor. This article discusses the situations in which the CIL circuit can be applied. The results of leach-carbon-in-pulp (CIP) and CIL circuits at Newmont Gold's Mill No. 2, No. 4 and No. 5 are presented for comparison: Mill No. 4 was initially designed for a throughput of 4.1 kt/d (4500 stpd). It is presently operating at an average throughput of 6.6 kt/d (7300 stpd) without significant changes to the original design. The design considerations of the Mill No. 4 CIL circuit are discussed. The design of any processing facility represents a series of decisions. The final design options should ultimately be resolved based on economic as well as technical considerations. Every design decision represents some sort of compromise. From the designer's view point, these decisions are made with the conviction that the final product represents the most prudent long-term expenditure. The design throughput rate is a decision reflecting a maximum return for the capital and operating costs that the plant will incur over the life of the mineral resource. The result is a plant that is not operator proof or maintenance free because it would be too costly to build. At some point, the incremental increase in the level of capital expenditure would not adequately compensate for the lower

Jan 1, 1991

By Barry R. Doyle, Ilsley Roger C., John Ramage

It was anticipated that settlement would occur when tunnels were excavated in weak organic soils with high groundwater levels in downtown Milwaukee. Because of the potential for damage to adjacent buildings, an approach was devised during the design to address this issue. In order to do so effectively, estimates of settlement trough geometry were made; buildings identified which were potentially at risk; the means of settlement measurement designed; and threshold limits of settlement and courses of action specified. Bid items were provided for underpinning the critical structures. The approach addresses the design issues and delineates the sharing of risk between the owner and contractor. The predicted and actual performance experienced are also discussed.

Jan 1, 1989

By E. J. Sullivan

This study seeks to define the mechanism of oxyanion sorption onto surfactant-modified zeolites. Zeolites which have been treated with hexadecyltrimethylammonium bromide (HDTMA) surfactant to produce a hydrophobic surface are capable of sorbing both organic compounds as well as oxyanions such as chromate, selenate, and sulfate. Simple ion exchange and charge-balancing mechanisms do not fully explain this unusual phenomenon. The sorption of HDTMA surfactant appears to be partly ion exchange and partly sorption to non-ion-exchangeable sites. Sorption of chromate is a simple exchange mechanism with bromide, which co-adsorbs with HDTMA to form a surface precipitate. Information from this study will be used to design on-site and in situ treatment systems for contaminated water, such as filter beds and permeable barriers.

Jan 1, 1995

By T. W. Peglas, J. Doherty, R. A. Day

The South East Transit Project is a $520 million project in Brisbane, Australia which includes the construction of a 32 km Busway to access the south-eastern suburbs. Close to the centre of Brisbane, tunneling techniques have been used to minimise surface disruption. This paper describes some of the features of the longest driven tunnel on the project, the Vulture Street Tunnel. The Busway is a two lane expressway for buses which requires a 10.2 m finished width and a 12.6 m excavated span of driven tunnel. The Vulture Street Tunnel carries the Busway at minimal cover beneath the operating Vulture Street Railway Station, beneath a three storey office building and beneath the roadway to the Mater Hill Busway station. Halfway along the route, a Y-junction has been constructed to enable future connection with a light rail route. Key features in the design and construction of the Vulture Street Tunnel include: Use of canopy tubes to drive a 12 m wide tunnel beneath operating railway tracks with less than two metres of cover in highly weathered rock. Underpinning the office building in the route of the tunnel construction from within the building carpark. Construction of a 24 m span Y-junction with 7 metres cover of weathered and faulted rock. Use of predictive analysis as an adjunct to traditional back analysis to estimate the tunnel settlements from pressuremeter test results. This paper describes the design methodology with particular reference to settlement prediction, as well as construction innovations used to complete the tunnel. This paper will be of interest to all designers who have to create large spans in minimal cover in weak rock in urban areas and who have to predict the settlement

Jan 1, 2001

By J. Richard Kyle

The Pb-Zn ore bodies in the Pine Point district are localized in paleo-solution structures that developed as the result of post-middle Givetian subaerial exposure of the carbonate barrier complex. Sulfides are concentrated in transgressive pale-solution structures that acted as natural bypasses between aquifers and loci for mixing of fluids of different character, one of which contained metals and the other reduced sulfur. Complex ore textures indicate rapid early sulfide precipitation followed by slower sulfide growth. Evidence for both sulfide-carbonate equilibrium and disequilibrium conditions suggest fluctuations in ore fluid composition. District and ore body metal distribution patterns may reflect the nature and movement of mineralizing fluids.

Jan 1, 1979

By R. E. Vivas, J. A. Villa

"INTRODUCTION Located in the state of Colima, Peña Colorada is one of the largest iron ore operations in Mexico. The project is owned in equal parts by ArcelorMittal and Ternium. Though boasting a production capacity of 4.5 million tons of concentrate per year, Peña Colorada is faced with declining ore grades. In order to respond to this situation, Peña Colorada had to expand production even further. This expansion created various challenges that were overcome by the adoption and application of new technology. Examples of these technological innovations are discussed in detail in this paper and include improvements in geo-modeling, mine planning and mine operations. The successful implementation of these technologies paid for itself many times over, and has led to significant improvements in production and performance, while lowering the operating costs and reducing the variance between planning and execution. PROJECT OVERVIEW Peña Colorada is a mining company which produces about 30% of the iron ore in Mexico. This project generates about 1,200 direct jobs and 3,000 indirect jobs, making a significant contribution to the local economy. Similarly, Peña Colorada invests in its local communities through numerous educational programs, scholarships, university agreements, social development, environmental agreements, etc. Peña Colorada’s operations consist of an open pit mine located in Minatitlán and a pellet plant located in the port city of Manzanillo, as shown in the location map below:TECHNOLOGICAL INNOVATIONS Most mining projects around the world typically follow the logic of “mining the next best ore”. Consequently, head grades tend to decline over the life of the mine. In the case of Peña Colorada, a decline in head grade combined with a decline in iron ore prices forced the operation to adapt to a new business environment and adopt new technologies to face these challenges. However, the first step along this process was to increase the confidence and reliability of the resource model. This task involved additional drillhole campaigns coupled with more detailed modeling techniques. Once the block model was completed, new optimization studies and production schedules were evaluated with new optimization tools that unlocked significant project value in many aspects of the mine plan. Similarly, new geotechnical studies were prepared, which provided new guidelines for pit slope design, and new technology was implemented to monitor ground movement and slope stability. The picture below shows two sectional block model views in MineSight 3D, along with the pit designs and geologic solids"

Jan 1, 2017

By Robert R. Munro

Traditional aggregate sources, that is the riverbeds, the alluvial fans, located relatively close to the developing urban centers are being foreclosed to mining. As the sand and gravel reserves are depleted, those production plants are unable to secure additional adjacent reserves and are being forced to close down. The sand and gravel industry, in many respects, is its own worst enemy. We promote development, we promote the paving of streets, the building of houses, and industrial and commercial centers, and because of economics, we tend to favor those developments located close to our operations. Thus, we encourage development by our neighbors who soon become our detractors. In general, urban development is not compatible with sand and gravel mining. The neighbors don't like the view of the pits or the quarries, they complain about the "dust", about noise, about trucking . . . in general, the neighbors are not happy being close to an aggregate source.

Jan 1, 1984

By Jürg Schlumpf

Concrete is one of the decisive construction materials, also for the AlpTransit Gotthard Tunnel. The client has many requirements, and many are the solution possibilities that concrete systems can offer. Cement producers and concrete admixture manufacturers have been challenged to design and test jointly concrete systems for cast and sprayed concrete. The testing operation followed the scenario laid out by the Gotthard AlpTransit Project management?s instructions ?Testing system for concrete mixes.? Various supplier teams have applied for the concrete systems for sections Amsteg/Erstfeld, section Sedrun and/or sections Bodio/Faido and have also followed through with the tests. As was to be expected, the rate of failed mixes matched the level of the requirements. Thanks to this system, it was nevertheless possible to test complete concrete systems for all sections and to get them approved. The joint ventures tendering for the contracts were allowed to include only approved mix designs in their bids. Workability and durability are of paramount importance for cast and sprayed concrete mixes. Durability is influenced by the chosen mix design where binder concept and well-defined water content, i.e., impermeability, are determinant. Aggregates for AlpTransit are to be considered as given. The concrete mix design also determines workability. Because ambient conditions and also requirements with respect to workability are subjected to change, it is necessary that the mix designs include control measures. The choice and number of components for the concrete systems (cement, additives and admixtures) allow adaptation to changing conditions. For AlpTransit such adaptive measures must meet very strict requirements.

Jan 1, 2008

By I. Weir-Jones

[Currently the cost of carrying out 'in situ' geotechnical investigation programmes or installing and operating monitoring systems at construction or mining sites is rising var." rapidly. This is primarily because of our ever increasing labour rates. As a result of this problem efforts are no,, being made develop techniques for the economical; collection of large quantities of geotechnical data relating, to such problems as done stability evaluation, the behaviour of underground openings, or 'in situ' testing procedures. The efforts to reduce the labour content. are particularly apparent in those procedures which have traditionally been manpower intensive e.g. 'in situ' permeability testing where an entire drilling crew and their associated eguipment have been on standby while testis has been carried out; or data collection in underground construction operations where much tine is typically wasted obtaining or maintaining access to instrument sites. In an attempt to illustrate one specialist consulting company's approach to the problem of reducing investigation costs, this rarer examines four recent developments in the field of geotechnical investigation and monitoring which have come about during the last two Years as a result of cur research and development programme. Although these techniques and devices have been developed for specific projects, they all have broad applications in the geotechnical field and they are indicative of the direction in which this company feels developments will take place.]

Jan 1, 1975

By J. T. Hollow

The Fort Knox Mine is located in Alaska?s interior, where the average ambient air temperatures range from -24°C (-11°F) in January to 16°C (61°F) in July. The mill processes a free-milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leaching, carbon adsorption and cyanide destruction kinetics. Additionally, an energy-balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy-balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy-balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post-project plant performance that validates the model and shows that the mine produced an additional 596 kg (19,155 oz) of gold while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By Tim O’Neil

The US Bureau of Mines and the Santa Cruz Joint Venture (SCJV) are working on a production-scale, in situ copper recovery project in Arizona. The research is being conducted at the Santa Cruz site, located 11.2 km (7 miles) west of Casa Grande, AZ (Fig. 1). Santa Cruz is a 1.36-Gt (1.5 billion st) porphyry deposit averaging 0.6% Cu, of which 65% is oxidized, concealed beneath post-mineral alluvium at depths of 365-914 m (1500-3000 ft). The Bureau and the SCJV will evaluate in situ mining as a method for extracting copper from this previously unmined deposit. Research objectives of the Santa Cruz project are: - to demonstrate that an in situ research test can be operated in an environmentally acceptable manner ; and * to operate an in situ well pattern long enough to develop information on copper recovery and economic feasibility data. In situ mining of copper from undisturbed deposits has not been attempted commercially. There are several potential advantages with in situ mining: less exposure of miners to hazards, lower pital costs for the mine and plant and lower operating costs. In addition, there are no pits, dumps or tailings, which means less environmental impact.

Jan 1, 1991

By M. Katzer

The effect of selective dispersants as wet grinding aids for ores is demonstrated on laboratory scale batch and continuous grinding equipment. A complete characterization of behavior is performed on a given ore to demonstrate correlations involving torque, % solids, net production rate, and slurry weight and volume loading. The relationship between such laboratory data and industrial scale testing results is very consistent.

Jan 1, 1979