Search Documents

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012

By N. S. Tanious

The Nuclear Regulatory Commission (NRC) regulation 10 CFR 60 requires that the ventilation system for the geologic repository be designed to: (1) control the transport of radioactive particulates and gases, (2) assure continued function during normal operations and under accident conditions, and (3) separate the ventilation of excavation and emplacement areas. The ventilation system design should take into account thermal loading; maintenance of the retrieval option and-the separation of the development and emplacement ventilation circuits. An analysis was performed by NRC's contractor, Engineers International on the ventilation system design described in the Department of Energy's conceptual design for Nevada. The ventilation analysis is of a preliminary nature. The conclusions presented in this paper reflect the views of the authors and may not represent the views of the NRC. In this analysis, available Nevada Nuclear Waste Storage Investigation (NNWSI) ventilation design information was reviewed and a ventilation network analysis was performed.

Jan 1, 1988

By V. K. Srivastava, T. Gupta, T. Ghosh

"In recent years, the demand for rare earth elements (REEs) has grown due to increasing demand and global supply shortage. The supply deficit of these critical elements has encouraged the search for new sources, with coal and coal byproducts as possibilities. Coals from certain parts of the world can be rich in REEs and can approach a total concentration of 1,000 ppm. Two Alaskan coal samples, from Healy and Wishbone Hill, were investigated for the effects of density and particle size on REE concentrations for three selected size fractions, and flotation tests were conducted on finer fractions. Additionally, bottom ash and fly ash samples from a power plant were examined for their REE concentrations. The results show that the upgrade potential for REEs on an ash basis from a whole-coal basis ranges from 2:1 for the Wishbone Hill samples to 4:1 for the Healy coal samples. Flotations of the finer fractions of the two coal samples, conducted under similar conditions, revealed higher concentrations of REEs in the tailings. Both coal samples had comparatively higher contents of light-group rare earth elements (LREEs) than heavy-group rare earth elements (HREEs). REE content trends for the power-plant products on an ash basis indicate that fly ash has slightly higher concentrations of both LREEs and HREEs than bottom ash. IntroductionRare earth elements (REEs), also known as rare earth metals, and their compounds are vital components in industrial, automotive, petrochemical, defense and medical applications. Dysprosium in combination with other elements is used in laser materials and nuclear control applications. Neodymium is present in magnets that are used in the manufacture of wind turbines and hybrid cars. Europium, terbium and yttrium are used in devices that have visual displays such as computer screens and laptops (Haxel, Hedrick and Greta, 2002; Bunzli, 2013). REEs pose fewer environmental problems of disposal and recycling than their conventional heavy metal counterparts (Haxel, Hedrick and Greta, 2002). They are key materials for radar systems, avionics, modern national defense and satellites (Cammarata and Sieradzki, 1994; Hedrick, 2010; Martin, 2010; Szumigala and Werdon, 2011; Cordier, 2011; Bunzli, 2013). REEs are often classified into light-group rare earth elements (LREEs) and heavy-group rare earth elements (HREEs). This classification is primarily based on the electronic configuration in the outermost shell. LREEs, ranging from lanthanum to gadolinium, have a single or no spinning electron in the outermost 4f shell while HREEs, ranging from terbium to lutetium, have paired electrons in the 4f shell. This difference in electronic configuration is responsible for the differences in physical and chemical properties of REEs."

Jan 1, 2017

By Kal V. S. Sastry

Mathematical and expert system models are being used extensively for mineral process engineering; nevertheless, standardized methodologies for their computer implementation do not exist. In meeting this need, this paper introduces the concept of a process software model, or more specifically an object-oriented software model, and presents a detailed methodology for its development involving software model specification and development. These software models provide a formal basis for the subsequent design and construction of software objects corresponding to the real world process objects.

Jan 1, 1995

By G. Castillo, J. Mortensen

"INTRODUCTION Molybdenite is typically produced as a co-product in the copper ore flotation process. At the Rio Tinto Kennecott Concentrator (RTKC) in Copperton, Utah, the molybdenite is initially floated with copper sulfides and other value minerals producing a Cu-Mo concentrate. This is then separated in the molybdenum plant by depressing copper sulfides and pyrite and floating only molybdenite. The molybdenum plant in RTKC comprises the rougher circuit and several stages of cleaning to achieve a certain grade requirement of Mo. The rougher circuit is where the first stage of separation occurs. Cu sulfides and pyrite are depressed in the rougher circuit by adding NaSH under nitrogen and in the cleaner circuit by adding NaSH under air. The depression of Cu sulfides (and pyrite) by NaSH is related to the redox activity1. It is important therefore to maintain a reducing potential in the circuit in order to achieve effective Cu-Mo separation. If the rougher circuit is under air, like RTKC’s molybdenum cleaner circuits, it is harder to maintain the target redox potential because NaSH oxidizes rapidly in the presence of air thereby increasing NaSH consumption significantly. CU-MO SEPARATION AND ROLE OF PULP POTENTIAL The collector adsorption on copper sulfide minerals is through an electrochemical mechanism2. The collector changes the surface chemistry of the Cu mineral allowing it to float. Molybdenite, or MoS2, on the other hand, floats readily in the presence of a frother as it is naturally hydrophobic. Usually, hydrocarbon oil extenders such as diesel or burner oil are added to enhance Mo recovery. In order to effectively separate Cu from Mo, the collector complex on the copper surface needs to be destabilized or desorbed using a reducing agent such as NaSH or Nokes. As long as the circuit is under highly reducing conditions, the collector remains detached from the sulfide mineral surface allowing Cu sulfide depression. Therefore, it is important to measure the oxidation-reduction potential (ORP) continually and maintain the reducing condition with addition of NaSH. For a given collector each mineral will have a characteristic potential or electrochemical window for flotation to occur3, therefore, it is necessary to reduce the potential outside of this window in order to effectively separate Cu and Fe sulfides from MoS2 minerals2. In RTKC plant, the target reducing condition is between -450 to -550 mV to effectively destabilize the collector and depress Cu and Fe minerals. Typically the dosage of NaSH used in the molybdenum plant could range from 6 to 30 gallons/min (gpm). The high dosage of NaSH could pose risk of H2S exposure. RTKC wanted to evaluate alternatives to NaSH in order to reduce its consumption and minimize risk of H2S gas generation."

Jan 1, 2016

By J. Pinkley

In June of 2002 Hilti North America received the first MSHA permissible approval for usage of a powder actuated tool device in a gassy mine atmosphere. The purpose of this paper is to discuss the implementation of this commonly utilized tool technology in the construction industry, to the underground gassy mining industry over the course of the last 5 years. Prior to June of 2002, underground gassy mining industry had attached materials such as ventilation curtains, power cables, communication cables, signage, and other materials by either manually driving individual spads or nails into the mine roof or rib or by attachment to existing roof bolt bearing plates. The Hilti DX 460 powder actuated tool is portable, durable, and lightweight (4.5 pounds). The Hilti DX 460 powder actuated tool system is powered by Hilti .27 caliber permissible explosive boosters. The energy force of the Hilti .27 booster?s acts on a captive piston principle in the Hilti DX 460 powder actuated tool, that applies the setting force for the direct fastening to the individual fastener chosen for the application by the end user. Each year Hilti can be called upon by MSHA to provide booster materials for re-testing per our Hilti DX PAD 1/00 approval.

Jan 1, 2008

By John W. Carson, David S. Dick

The last few years have produced new methods of characterizing flow properties of bulk solids. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field condi¬tions. In addition, the effect of large par¬ticles on a material's flow properties (cohe¬sive strength, bulk density, wall friction) can be determined as well as the effects of var¬ious additives such as freeze conditioning agents. New developments have occurred with devices to improve the reliability of solids flow. Much attention has been paid to find¬ing ways, by using inserts, to provide a mass flow pattern with relatively shallow hopper walls. Such devices can also provide reli¬able in-bin gravity blending of bulk solids or completely nonsegregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. The technology and hardware for running bench scale flow tests on bulk solids samples and transforming the results into reliable designs has been in existence for nearly 30 years (Jenike, 1964; Marinelli and Carson, 1986). It has been shown repeatedly that reliable materials handling systems can be designed to avoid the problems of no-flow due to arching or rat-holing, erratic flow, segregation, loss of capacity, or spontaneous combustion. Running flow properties tests and carefully designing a bulk handling system are not expensive, particularly when compared to downtime costs and continual flow problems. New developments in characterizing flow properties of bulk solids include: • a shear tester for measuring the properties of run-of-mine ores containing large par¬ticles; • attrition testers to simulate a wide range of flow conditions; • a tester to measure the wear rate of liners in bins, feeder parts, etc.; • a dustiness tester to measure the potential for dust and the effect of dust control meas¬ures; and • techniques for measuring the strength of frozen ores and the effect of freeze condi¬tioning agents. In the area of improving the flow of bulk solids, there are new techniques for ensuring reliable flow without using up excessive headroom. These include: • belt-to-belt transfer chutes to handle po¬tentially sticky, abrasive, and dusty ores; • designs for the interface between a bin/ hopper and apron or belt feeders to avoid hangups and minimize feeder loads; methods to feed solids reliably into a pres¬surized process; and designs for handling systems that will mini¬ mize attrition, avoid segregation, or auto¬matically blend materials together. Characterizing flow properties Large shear cell It has long been known that the cohesive strength of a bulk solid is due mainly to its fine fraction. However, the effect of the larger particles (that were assumed to re¬duce the strength) could not be measured. The development of larger scale (205 mm¬diam and 0.6 x 0.9 m or 8 in.-diam and 2 x 3 ft) shear testers has made it possible to measure the properties of a wider range of materials. Now cohesive strength measurements can be made with up to 100 mm (4 in.) particles. The results obtained from the large shear testers, together with the results of the nor¬mal shear tests on the fine fraction, are used in the design of reliable stockpile reclaim systems and crusher feed systems. A high percentage of large particles can reduce the measured shear strength of a bulk solid. However, segregation may alter the size distribution and should therefore be considered (Carson, Royal, and Goodwill, 1986). In addition, larger particles will

Jan 1, 1989

By P. B. Moran, J. W. Rozelle, J. Forbort

"The Mount Todd gold mine is located approximately 50 km (31 miles) north of the town of Katherine in the Northern Territory (NT) of Australia just off the Stewart Highway, and was operated in the 1990s until 2000 (Fig. 1). After cessation of mining operations, meteoric precipitation and acid rock drainage (ARD) associated with surface water runoff continued to report to the retention ponds across the mine site. In 2000, the mine site entered receivership and the NT government became responsible for the care and maintenance program. In 2006, Vista Gold Corp. (as Vista Gold Australia) acquired the rights to resume exploration on the mine site without the financial responsibility of the environmental liability. In January 2007, Vista Gold assumed the care and maintenance activities on behalf of the NT government, with the environmental liability remaining with the NT government, with the goal of reinitiating mining operations. A critical path component of the planned upgrades to the existing mine/milling facilities and infrastructure was the development of a cost effective treatment and dewatering program for the approximately 11 GL (2,900 million gal) of ARD stored in the Batman Pit (RP3), which has a maximum capacity of approximately 12 GL (3,200 million gal). The Batman Pit must be dewatered in order for Vista Gold to restart mining activities. The Batman Pit Lake had reached a maximum water depth of 104 m (341 ft) when Vista Gold initiated water level monitoring. It is important to note that the ARD water in the Batman Pit has been pumped into it from 2000 to 2012 under an NT government-approved environmental control program.The Batman Pit has virtually no connection to the local ground water regime due to the intensive silicification that accompanied the mineralizing event. In October 2012, just prior to treatment, the pit lake profile was characterized by uniform acidic pH (approximately pH 3.2) and oxic conditions (dissolved oxygen greater than 7 mg/L with depth (Fig. 2). The temperature decreased by approximately 4 °C (39 °F) between the lake surface and approximately 20 m (66 ft) deep, and remained near constant with increasing depth. This temperature difference is believed to be associated with an existing shallow mine bench at approximately 20 m (66 ft) deep around the perimeter of the pit. Similarly, electrical conductivity, an estimate of total dissolved solids, decreased by about 85 microSiemens per centimeter (µS/cm) from 2,800 to 2,715 µS/cm between 10 and 20 m (33 and 66 ft)."

Apr 1, 2016

By William T. Griswold

Few metals or industrial minerals can boast a better growth record over the past fifteen years than the borates. This period of growth occurred before the influence of any large-scale use in plastics or high-energy fuels. These new developments not only provide expanding markets, but the programs related to their development are generating research information that will lead to many other new uses. The most dynamic growth areas for refined products of boron or borates are in the acid, the oxide and the reduced forms, such as the metal and the hydrides. Expanding requirements for these products will modify the emphasis on the use of naturally occurring sodium borates. Any borate from which boron can be economically extracted will become a potentially important ore. This is particularly true of the calcium borate, colemanite. Only one large deposit in the Western World has ever been developed where the principal economic minerals are sodium borates, This factor alone would discourage any exploration program directed solely toward the discovery of these ores; on the other hand, ample exploration opportunities for calcium borates exist in the desert regions of California and Nevada. It is therefore reasonable to restrict a program to this region, in spite of geologically favorable areas in foreign countries such as Turkey, Argentina and Chile.

Jan 1, 1959

By A. D. S. Gillies

Inertisation is used to enhance the safety of underground mine areas either to avoid the potential for a combustion event or to stabilize a situation after an ignition, fire or heating. The primary objective of a recently completed Australian Coal Association Research Program (ACARP) study was to review coal mine inertisation and in particular to focus on use of the Polish mine fire simulation software Ventgraph to gain better understanding of how various inertisation units interact with the complex ventilation behavior underground during a substantial fire. Critical aspects targeted for examination under the project grant included location of the unit for high priority fire positions, size of borehole or pipe range required, time required for inertisation output to interact with and extinguish a fire, effects of seam gases on fire behavior with inertisation present and main fan management. A major accomplishment of the project has been to take findings from the simulation exercises to develop inertisation related modifications to the Ventgraph fire simulation program in conjunction with the Polish program authors. Selected mines were ?evaluated or audited?as to the ability to deliver inert gases generated from GAG units to high priority underground fire locations .A coding system has been developed and many potential underground mine fire sources cannot be successfully inertized with the GAG docked at the current specified point; this is particularly so for fires in extended areas of workings or in panels. There is a limit to the ability of the GAG jet engine to deliver exhaust down smaller dimension borehole. There is a need to examine the use of the GAG for production or proactive uses in a wider application in Australian mines responding to recovering from mine fires, spontaneous combustion heating?s, elimination of the potential explosibility of newly sealed gobs or inert mines or mine sections on closure. Some of the current uses of low flow inertisation facilities could be more effectively undertaken with the GAG unit.

Jan 1, 2009

By A. Roper

Since the Toronto conference in May 2002, the International Council on Mining and Minerals (ICMM) has made progress on the road to sustainability. Fifteen of the world?s largest mining and metal producing companies and twenty-five associations have made a long term commitment to ICMM to improve the environmental and social sustainability of their activities. Sir Robert Wilson (Rio Tinto) assumed the chairmanship of ICMM in October 2002. By December 2002, the Council had approved a Strategic Vision and an operating plan for 2003. Both have been posted on the ICMM website (www.icmm.com). ICMM?s Operating Plan sets out three priority tasks: - Providing strategic leadership to achieve improved sustainable development performance in the mining, minerals and metals industry. - Contributing to international policy discussions on cross-cutting issues of importance to the industry, in collaboration with national and commodity associations. - Promoting dialogue and partnership with other organizations to catalyze sector?wide sustainability initiatives.

Jan 1, 2003

By E. G. Kelly

This paper describes the performance of a modern compound trough profile spiral that is optimized for fine coal cleaning. Reduced performance (Tromp) curves are presented to compare these new spirals with older designs, as well as with other commonly used coal cleaning equipment. As an aid to equipment selection and circuit design, data are also presented to show how variables, such as flow rate, pulp density, and particle size affect efficiency and the separation specific gravity.

Jan 1, 1984

By Charles T. Holland

The tonnage produced on mechanized automated retreating longwall faces in the United States is growing rapidly. This time last year some 14 faces were operating, and in addition to that, three were known to be down looking towards revision or repairs before being placed back in service. These, it is believed, are now in service. It is estimated at the present time, therefore, that somewhere between 20 and 25 faces are being operated in the country. A survey made last year by the School of Mines, West Virginia University, indicated that longwall mining in general has been beset with a great many problems, some more serious than others. The problems that we propose to discuss here are those pertaining to roof and floor trouble in the tailgates. Longwalls are operating in this country at the present time under an overburden ranging from 200 feet to nearly 3000 feet. Main and tailgate entries are operating in panels of up to five each, with the width of the pillars between these entries varying from 20 to 50 feet. Face lengths are running from 270 feet to 670; actually a face 800 feet long should be possible. The most economical face is often spoken of as being around 450 feet.

Jan 1, 1969

By R. G. L. McCready, G. Dr. Heinrich, V. I. Lakshmanan

The objective of this study was to prove repeat loading capacities of physically stabilized fungal biomass from Penicillium sp. for the removal and recovery of uranium from mine water (Denison Mines). The testwork was carried out on a bench scale in small columns and proved that it is possible to stabilize the biomass in an inorganic compound. A lifetime of 10 loading-eluting cycles of the stabilizer biomass product was obtained by additional pretreatment. Sodium carbonate proved to be an effective elution medium. Loading and elution can be controlled by the pH values of the column. The effective loading capacity until the breakthrough point is approximately 70 % of the overall loading capacity. The loading capacities of the stabilizer biomass product are comparable to that of the original biomass. Uranium recoveries of 90 to 99 % were achieved during the loading and eluting under optimized conditions. Depending on the used biomass the described process might be applicable to remove uranium or other dissolved heavy or rare metals from effluents.

Jan 1, 1989

By Thomas G. Langton

The demand for mineral raw materials, especially in the major industrialized nations, has grown rapidly during the past three decades. One consequence of this growth has been an increasing reliance by the large industrialized countries upon nondomestic mineral supplies. These mineral supplies, to a large extent, have been developed by capital from the major industrialized countries. Until recently, most foreign mining ventures were either wholly-owned subsidiaries or joint ventures between two or more mining companies. The recent rise of economic nationalism has substantially changed the business climate and parameters under which foreign investors operate. This paper describes some of the underlying reasons for this change and notes how investors have adapted to the new business conditions.

Jan 1, 1974

By Zhang Youdi

A two-step approach has been developed for surface mine short term planning by the authors. The first step is mid term control and planning by the use of Goal Programming. This step gives optimal results for mid term planning (i. e. yearly or quarterly mine plan) as well as a macro control for short term planning (i. e. monthly or weekly plan.) The second step of the approach deals with short term production scheduling by the application of CAD technique and Systems Simulation. An interactive color character graphic design system has been developed with a software package. The menu-driven and module- structured package provides sufficient functions for surface mine short term planning and makes the model very flexible and user-friendly. This model has been applied to a large surface coal mine for short term planning optimization. Satisfactory results have been obtained. It is concluded that for complicated mining conditions this two-step combined approach gives an optimal control of mid term planning, makes the short term planning easier to avoid blindness; it has been proven that the Goal Programming is a powerful tool for solving multi-objective decision-making problems; guided by GP mid term planning, the CAD technique and simulation software package for short term planning are able to be concentrated on their practicality and flexibility.

Jan 1, 1992

By P. D. Pack, E. H. Skinner

During design of a 550-foot rectangular shaft in alluvium, lateral support within the excavation was an anticipated construction problem. Actual experience showed that the nearly 9 x 14 foot excavation required no lateral support. A strain measurement program con- current with construction and for a 9-month period following completion of the shaft detected only minor strains. Shaft design included consideration of available geological information. Site exploration included a 754-foot drill hole, cored at selected intervals, and a suite of geophysical well logs. Generalized physical properties of the alluvium were developed from laboratory core testing. An elasto-plastic, finite element computer program (DAHLKE) developed by the Spokane Mining Research Center U.S. Bureau of Mines, has been recently used to analyze the behavior of the alluvium around the shaft. Analysis showed that yielding first develops in the shaft corners and progressively expands into the wall zones around the shaft as loading increases. Gradual growth of a plastic zone progressed outward from the excavation boundary at increasing loads but had limited extent and was surrounded at all stress levels by an infinite elastic zone. This design review, aided by computer analysis, confirmed that the shaft would have been considered theoretically stable as designed.

Jan 1, 1977

By J. Ye

A comprehensive flotation study has been carried out on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University. The results are compared with that of a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4-S% higher recovery and much lower silica impurity content than that produced by up to six stages when a conventional mechanical cell is used. The results also show that the packed column flotation process is particularly suitable for recovery of finer fluorspar particles.

Jan 1, 1992

By S. C. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photoelastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface, and (3) the effects of subsidence on tension in the truss members.

Jan 1, 1987

By Richard D. Harvey

Relative quantitative analyses of certain mineralogical and textural properties of carbonate rocks were made with an image analysis computer. The instrument, referred to by its manufacturer as a Quantimet; consists of a petrographic microscope, a television camera and monitor, a detector, an electronic computer, and a read-out meter. Measurements were made on polished and etched specimens, standard thin sections, and on scanning electron micrographs of carbonate rocks. Critical to the success of the analysis is the preparation of the specimen in such a way that good optical contrast is obtained between the various petrographic components. The dolomite content, the pore volume, pore boundary projection, and pore size distribution of high-purity carbonate rocks were measured by image analysis methods. The frequency and size distribution of void inclusions in dolomites were determined by image analysis of scanning electron micrographs of cleaved surfaces. Image analysis methods permit rapid and quantitative assessment of various microscopic properties. The results are of reasonable accuracy and certainly are relative quantities that may be used to characterize carbonate rock materials.

Jan 1, 1972