Search Documents

By A. S. Hall

Significant pyrite often does not dissolve in the Sobek (1978) nitric acid extraction; therefore, the standard conservative approach is to estimate pyrite using sulfur present in the sum of the nitric acid and residual sulfur fractions. Alunite, when present, appears as residual sulfur. Because alunite does not generate acidic effluents, overestimation of AGP can occur if all residual sulfur is assumed to be undigested pyrite. Evaluation of 16 samples from the Florida Canyon Mine revealed that petrographic examination coupled with a modification of the Sobek method to include a 6 hour hot (250°F) 'nitric acid extraction resulted in a more accurate estimation of AGP.

Jan 1, 1999

By J. S. Limb

Actual issues which arose during the discovery process or subsequent court testimony are presented. While most of these issues relate to the author’s specialty of mineral appraisal some are more general in nature and could be of interest to those who may be involved in current or future court testimony. Several important areas to be reviewed and agreed upon with the client and their legal counsel are discussed. General observations on litigation, the discovery process, testimony and some repercussion’s are also given.

Jan 1, 2001

By Bill Morgan

This paper discusses the economic zones of application for several different types of earthmoving equipment: dozers, wheel loaders in load-and-carry applications, wheel tractor scrapers, articulated trucks, rigid-frame trucks and wagons. Only the medium to large pieces of equipment were considered. From this chart (Figure 1), you can see the size range, in tons of carrying capacity, of Caterpillar equipment and the specific models analyzed.

Jan 1, 1994

By H. P. van Ormer

The objective of this paper and the developed personal computer program is not to identify or try to identify the actual total drilling cost in any Rotary Drilled Blast Bole Program. The ideas put forth here and in the computer program developed are a very accurate way to measure what is often very hard to identify and interpret -The actual direct operating cost of various drilling package combinations including comparing with available blast hole sizes and patterns

Jan 1, 1988

By Derek J. Barratt

The specification of the prime mover of an autogenous/semi-autogenous mill involves an analysis of the likely operating conditions within the mill and the choice of a nominal operating speed. For variable speed mills, the operating range for mill speed has to be defined so that mill power/torque requirement can be matched by the motor power/torque capability. This paper will describe how this relationship can be influenced by ore grindability.

Jan 1, 1993

By David T. Kao

The energy situation the world faced during the decade of the Seventies resulted in actions throughout the free world to reduce its dependence on OPEC oil. Many nations heeded the indicators early in that decade and commenced efforts to reduce their oil requirements. Those nations which did not heed these warnings had the message brought to them more emphatically in the last portion of the decade with the further rapid and continuing rise in prices of OPEC oil. Furthermore, the demonstrated unstable nature of large oil-producing countries has made it clear to all free world nations that their energy demands of the future must be provided for by some more stable and assured supply. Now, early in the decade of the Eighties, we see the need for expanded use of coal as an energy supply to be essential. The result in 1980 and 1981 has been a great increase in demand for steam coal worldwide. In essence, a new business for the United States has developed in steam coal export. In the United States, the large growth in foreign demand for our steam coal is now well recognized and documented. A major impediment in meeting this growing demand became abundantly clear in 1980. This impediment is the congestion existing at U.S. coal export ports. With the recognition of this constraint, a plethora of activity has been observed in announcements for alleviating the problem by improving and expanding current export port facilities. In addition to improvement and expansion, an abundance of totally new facilities has been announced in an effort to find ways to meet this large demand in the new business of steam coal export. This is needed; and hopefully, many of these plans will be translated into action. While total implementation of all stated plans is not expected, much of the implementation depends upon large- scale dredging, large waterside ground storage sites, and improved handling equipments in the conventional type of export ports. The time and capital required for implementation is great, and environmental problems associated with dredging are substantial. Host significantly, and unfortunately, implementation that does include dredging our ports will still not permit use of the truly large colliers of 140,000 DWT and greater, which are evolving as the "state of the art" in long-distance sea transport.

Jan 1, 1981

By C. H. Grant

The Dew Chemical Company has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which Dow is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of non-metallized explosives currently being used. Early in 1960, we acquired additional patent rights from independent inventors and decided to set up a development station at Virginia, Minnesota, to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the bore holes. Due to the complexities involved in controlling the manufacture of the explosive in the bore hole, performance was sometimes in doubt. Furthermore, our experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation, and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over two thousand charges of eight to 60 pounds under water and in taconites and granites with many types of explosives, we have developed a metallized explosive which is now being manufactured at a pilot plant in Virginia, Minnesota, and is being evaluated commercially.

Jan 1, 1963

?Energy-related systems: wind, solar, electric are typically materials intensive. As new technologies are widely deployed, significant quantities of the elements required to manufacture them will be needed. However, many of these unfamiliar elements are not presently mined, refined or traded in large quantities, and, as a result, their availability might be constrained by many complex factors. A shortage of these ?energy-critical elements? could significantly inhibit the adoption of otherwise game-changing energy technologies. This, in turn, would limit the competitiveness of the U.S. industries and the domestic scientific enterprises and, eventually, diminish the quality of life in the US.? -Energy Critical Elements: Securing Materials for Emerging Technologies?- American Physical Society, 2011.

Jan 1, 2012

By John W. Scott

INTRODUCTION The design criteria for a particular concentration and dewatering project will provide the formal basis for design of the process, equipment and facilities. These criteria will specify the required capacities and operating schedules for the equipment, as well as the quantity and quality of the feed to be processed and products obtained. The general climatic and geographical conditions at the site, specific information on soil or rock conditions; and applicable design standards and codes will also be included. The design criteria will generally be based on an interpretation of testwork carried out on the particular ore and site, and will thus parallel in detail and completeness this testwork. As the project moves from the early conceptual phases through to final detailed design, the design criteria will be developed and become more detailed as information is generated and made available for use. The design criteria are critical to the design effort as the formal specification to the designer of what and how much is to be processed, what and how much is to be produced, and where and under what conditions. The actual design criteria will be a formal tabulation of the design basis information developed for the project in question. For a preliminary study, this may consist of a single page of data; for a feasibility study several pages and for a detailed design up to several hundred pages and multiple volumes. Depending on the complexity of the process and the level of detail included, each project will be unique to some degree. The design process for a project normally progresses from preliminary conceptual phases through to a final detailed design. The criteria used for the initial concepts are generally developed from rough data and preliminary testwork on the ore in question. Regardless, the plant throughput and products are defined, thus giving a scope and definition to the study phase. In some studies a range of throughputs may be analyzed in order to arrive at the most economically attractive size for the proposed operation. This optimum size is then used as the design throughput for the more detailed design phases. Similarly as more testwork results are available and the ore characteristics and process become more well defined a continuous updating of the design criteria is undertaken.

Jan 1, 1986

By William L. Carter

Through your presence here this morning and your membership in the Society of Mining Engineers, you have shown that you are interested in keeping abreast of the latest technology and mining procedures, want to be part of the continuing progress made by those in your profession, and are looking for ways to participate in expanding your professional and personal experiences and skills. All of these factors are part of your continuing education, the need for peer identification or recognition, and the desire to make a specific contribution to strengthening your profession. However, you may be here with or without your company support and financial backing, unless you are self-employed. Whether you are here for the above reasons, or for many others, your presence reflects a recognition of the importance of participating in the organizational structure of your profession.

Jan 1, 1981

By J. Bigu

Ventilation conditions in working environments are usually studied by anemometry or, in complex cases, b using special tracer gases such as SF6 and 85Kr. in conjunction with chromatographic and radioactivity techniques, respectively. In some working environments, such as underground uranium mines, however, use can be made of the natural radioactivity environment (e.g.. 222rn. 220rn, and their progeny) to investigate mine ventilation conditions of practical interest. Theoretical studies and experimental data in several underground uranium mines and mine locations show that certain thoron progeny to radon progeny concentration ratios are very good indicators of ventilation conditions. Furthermore, the growth and decay of radon progeny and thoron progeny provide valuable information on mine air residence and clearance times. Some specific examples have been analyzed, such as bacterially-assisted uranium leaching operations in a partially enclosed stope, and the effect on the underground environment of turning ventilation fans on and off for a period of time. Air residence times and other variables of interest, determined from the mine radioactivity environment, were compared with more traditional techniques, such as anemometry and tracer gas chromatography. These studies were also extended to a wet non-uranium mine which exhibited relatively high concentrations of radon and its progeny.

Jan 1, 1989

The surface of chalcopyrite was studied in situ in aqueous solution by an atomic force microscopy (AFM). The AFM images showed that some absorbate in patches was detected on the mineral surface, after the chalcopyrite sample was soaked in 5x10-4M potassium ethyl xanthate (KEX) solution at pH 11 for 10 minutes. These patches increased in size with time elapsing. At the same time, as shown by the obtained AFM force curves, the adhesion between the AFM tip and the substrate increased greatly due to the adsorption. Rinsing with ethanol removed the absorbate from the chalcopyrite surface, as well as the big adhesion observed in KEX solution.

Jan 1, 2010

By O. Ozcan, J. D. Miller, Z. S. Nickolov

The production of soda ash from trona (sodium sesquicarbonate, Na2CO3•NaHCO3•2H2O) resources has completely displaced the production of synthetic soda ash in the USA. Further, the utilization of other trona resources is under consideration in China, Turkey, etc. Recent research has been concerned with the development of flotation technology for the trona industry. In this regard studies on the flotation behavior of sodium carbonate salts: trona, sodium carbonate monohydrate and decahydrate, as well as the flotation behavior of sodium bicarbonate, are reported for both cationic (dodecyl ammonium hydrochloride) and anionic (sodium dodecyl sulfate) collectors. It has been found that strong flotation of sodium bicarbonate (NaHCO3) can be achieved with 100% recovery, while the other sodium carbonate salts do not float well. These results have been explained by FTIR analysis of aqueous solutions of Na2CO3and NaHCO3in a range of concentrations from very dilute to saturated conditions. The changes in the shape of the O-H stretching band of water are correlated with the flotation behavior of Na2CO3salts and NaHCO3. In addition, the absorption band of the carbonate ion at ca. 1385 cm-1is used to monitor its interactions with water and/or other ions in solution. The infrared results demonstrate thatNa2CO3acts as a water structure maker, leading to an extensively hydrated surface that accounts for the poor flotation of most sodium carbonate salts. In contrast, NaHCO3does not have this characteristic and consequently complete flotation is possible with both cationic and anionic collectors. These results support the previous water structure analysis for soluble salt flotation of alkali halides and other oxyanion salts.

Jan 1, 2003

Arsenic (As) removal behavior from Changgoon mine tailings was investigated using Acidithiobacillus ferrooxidans (A. ferrooxidans) in well-controlled batch reactors by varying pulp density (0.5?4%, pH=1.8, temp=30oC), reaction initial pH (1.8?2.2, pulp density=0.5%, temp=30oC), and temperature (25?35oC, pulp density=0.5%, pH=1.8). The initial concentration of As in the mine tailings used for bioleaching tests was about 30000 ppm, and the size range of tailings used in this study was 63?74 µm. The reaction speed and initial cell concentration were fixed to 150 rpm and 107 cells/mL, respectively. To complement leaching experiments, pH, oxidation/reduction potential (ORP), and amount of ferrous/ferric ions in leachate were analyzed. Scanning electron microscopy and x-ray diffraction analyses were also conducted for the samples before and after leaching to see if any morphological and compositional changes in tailings took place during leaching process. The As leaching efficiency increased with decreasing pulp density, decreasing pH, and increasing temperature in the presence of A. ferrooxidans. Specifically, no significant change in As removal rate was observed when pulp density d 2% while the removal rate dramatically decreased at pulp density of 4%. Regarding pH effect, As removal rate was much more enhanced at lower pHs (i.e., 1.8 and 2.0) compared to pH 2.2. Increasing temperature was observed to tend to enhance As removal rate, showing about 20% enhanced leaching rate under 35oC compared to 25oC and 30oC at the elapsed time of 5 days. The results for As removal behavior at different conditions (i.e., pH, temperature, pulp density) were consistent with the change in pH, ORP, and ferric ion concentration in leachate, showing greater removal rate at the condition with lower pH, and higher ORP and ferric ion concentration in leachate. Furthermore, decreasing removal efficiency was likely in part due to the extent of the formation of by-product (i.e., jarosite) of ferric ions.

Feb 27, 2013

By C. Sykes, E. Turner, M. Wyart-Remy

This paper follows that of the Milos Conf, 2002 and examines the collection and reporting of SDIs in the industrial minerals industry in Europe. It compares the characteristics of the GRI Reporting Guidelines, with its Metals and Mining Sector Supplement with those of the EU DG Enterprise Scheme, launched in 2001. The particular issue of SME's and companies which are not publicly traded is examined. The pros and cons of participating in such schemes is a central theme of the paper. The paper concludes that there and many business benefits for these companies in participating and submitting their data. The European Commission Scheme is strongly recommended for companies in the sector which are SME's and not-publicly traded as well as large firms who are listed on European Stock Exchanges.

Jan 1, 2005

By Hans Smit

The face of mining as we know it is set to change in the very near future as mining companies all over the globe realize the implications of accessing the vast mineral wealth contained on, and under, our ocean floors. With some land based mineral deposits being fully exploited across the world, deep sea mining is set to revolutionize global approaches to the search for precious metals and other sought after minerals. [ ] Previously, the financial implications of deep sea mining outweighed the benefits of access to the mineral rich deposits identified all around the world. The process of marine diamond mining off the west coast of southern Africa started in the late 1950?s by a Texan, Sammy Collins, and subsequently continued by De Beers to the present day, has proven to be an excellent proving ground for the development of technology and mining systems that ensure a sustainable and financially viable business. [ ]

Jan 1, 2008

By Peter Klaver

Deep tunnels have been used for decades for the temporary storage of large volumes of urban runoff, both storm water and combined sewer overflow (CSO). Tunnels are attractive because they reduce surface disruption and do double duty as storage and conveyance systems, collecting overflows from multiple locations and transporting them for treatment to various facilities. Like any hydraulic system, however, there are dynamic effects that must be fully understood during the design phase so that the final constructed product does not have unintended negative consequences. Preliminary sizing of storage tunnels is typically based on the total volume required. For example, if studies have determined that a volume of 56.8 ML (15 million gal) will provide the intended level of control, then that figure can be used, along with a preliminary idea of the desired tunnel length, to compute the required diameter. Of course, filling a long tube with water from various points along the way is not at all the same as pouring water into a bucket, and these dynamic effects require additional attention from design engineers. The rapid filling of storage tunnels can lead to the formation of bores, which are essentially moving walls of water. An open channel bore can build in height until it reaches the crown of the tunnel, at which point it becomes a pipe-filling bore. Figure 1 depicts both kinds of bores moving upwards in a rapidly filling tunnel. Bores can strike the ends of tun-nels with tremendous force, driving water and entrained air upwards into dropshafts and creating strong pressure surges in portions of the tunnel that are already filled. If the hydraulic surges are high enough to reach grade, they can cause overflows and/or damage structures at the surface. Trapped air pockets can occur through several phenomena, including the reflection of bores off dropshaft structures and the occurrence of ?premature pressurization.? The latter refers to the situation where the inflow to a tunnel is increasing more rapidly than the tunnel can convey it, such that the pipe becomes surcharged at an upstream point while points downstream are still flowing as an open channel. These air pockets are a great nuisance as they migrate toward points in the tunnel where they can rise to the surface, which are often shafts that are already filled with water (Fig. 2). The ?geyersing? that results can be hazardous and costly.

Jan 3, 2010

By A. T. Yu

As a nation, we have been known as perhaps the most wasteful in history. From the perspective of engineers and builders on the other hand, planned obsolescence and demolition did beneficially pave way for growth and provided environment for new businesses. Recent economic recession and intense competition from overseas, however, have drastically changed the economics. The high cost of capital and the demise of indiscriminate plant expansion have totally altered the way we conduct our business and run our operations. As a response to increasing demands for better efficiency with little or no funding available, everyone is forced to make do and do better with whatever little he has. Today it nay not be an exaggeration to state that modification of existing facilities may have finally emerged as a way of life. This paper will outline examples of how several companies have effectively modified existing facilities to do more and do it efficiently without having to demolish everything and/or to spend a fortune.

Jan 1, 1985

By John Reynolds, Robert Sloan

The Escondida copper mine is located in the northern Atacama Desert of Chile at an elevation of 3,050 m. approximately 160 km southeast of the port of Antofagasta. The mine is a joint venture between BHP-Billiton, Rio Tinto, a Japanese consortium and the International Finance Corporation. The most recent expansion, Laguna Seca, has increased the total capacity to the level of 220,000t/d ore throughput. The ore body, a typical porphyry deposit, is situated on the major Chilean west fissure fault system and contains primary sulphide ore grades between 0.6% and 2.0% copper. Primary sulphide mineralization consists of chalcocite pyrite, chalocopyrite, bornite and covellite. Significant copper oxides overly the sulphides in many areas.

Jan 1, 2005

By Walter E. Cook

BOB FALCONER: Without further ado I'm going to introduce our first speaker, Walt Cook. Walt is president of Strata Resources and is here with his business partner Joe Nenni. Joe would you stand up here. You'll be on the tag-team with Walt. Walt and Joe are in a consulting business associated with coal as well as metal and nonmetal industries. Their presentation will be on gainsharing. WALTER COOK: How many of you have gainsharing plans in place currently at your location? [show of hands] A considerable number-more than about half the room. Of those plans, how many of them do you consider as meeting your needs and being successful? [show of hands, far fewer, general audience laughter] You have all at least heard the word "gainsharing." Some of you undoubtedly aren't quite sure what gainsharing is, while others obviously have gainsharing plans in place and are looking for ways to improve them. In the short time I have now I'll be able to give you a precursory look at gainsharing and some brief ideas on where to look to improve your current plans. Over the years, I've found that it is often best to explain gainsharing by comparing it to other forms of employee compensation

Jan 1, 1998