Search Documents

By M. Churchill, V. R. Degner

Over the past two decades, declining ore body grades and increased operating and construction costs have provided an incentive for the development of progressively larger flotation machines. As a result, the 1.7-2.8 m3 (60-100 cu ft) flotation machine of the 1950's and 1960's is being rapidly replaced by large volume machines. The result has been improved flotation machine specific capacity (tph processed per sq ft of floor space); specific power (hp per tph processed); and process control simplicity. The recent development and satisfactory plant evaluation of the 28 m3 (1000 cu ft) flotation machine allows economic and operating advantages in high tonnage mill applications. Some principles of mechanically induced air flotation and the development of the large 28.3 m3 (1000 cu ft) flotation machine are reviewed here. Performance evaluation in beneficiating metalliferous ores-copper, zinc, and iron-is also given and recently completed plant results provided. Mining lower grade ore bodies results in the need to process increased tonnage in the concentrator. This greater tonnage requires more individual flotation machines, unless individual machine capacity, or cell volume, is increased. As the ore processing rate of the concentrator increases, the benefits of progressively larger individual cells in the flotation section become more significant. The accompanying figure illustrates the advantages of a larger flotation machine. In the figure, the number of machines in the rougher-scavenger section is related to the plant tonnage for three sizes of flotation machine: 8.5 m3 (300 cu ft), 14.2 m3 (500 cu ft), 28.3 m3 (1000 cu ft). The 28.3 m3 (1000 cu ft) flotation machine results in 95 fewer machines, compared to the 8.5 m3 (300 cu ft) machine at 45.4 kt/d (50,000 stpd) feed. The flotation cell reduction is, of course, doubled at a plant production rate of 90.7 kt/d (100,000 stpd). Using fewer flotation machines saves floor space. The 14.2 m3 (500 cu ft) and the 28.3 m3 (1000 cu ft) machines result in a floor area reduction, relative to the 8.5 (300 cu ft) machine requirements, of 134.7 and 418.1 m2 (1450 and 4500 sq ft), respectively, for the 45.4 kt/d (50,000 stpd) rate and 269.4 and 836.1 m2 (2900 and 9000 sq ft), respectively, for the 90.7 kt/d (100,000 stpd) rate. In addition, flotation practice has shown that the "specific power intensity"-power per unit cell volume-is less for increased cell size. This results in a power draw reduction, for the rougher-scavenger circuit, of between 552 and 686 kW (740 and 920 hp) for the 14.2 and 28.3 m3 (500 and 1000 cu ft) machines, respectively, when processing 90.7 kt/d (100,000 stpd). Fewer cells improve machine control and simplify maintenance needs while reducing floor space and power requirements. These are tangible incentives for the development of large flotation machines for high tonnage applications. Flotation Principles The accompanying figure shows how key hydrodynamic regions influence the performance of a mechanically induced air flotation machine. Air is induced into the fluid from the top of the cell, due to the mechanical action of a rotating impeller. The impeller circulates the liquid, or pulp, from the bottom of the cell. The result of these dual flow paths is the mixing of the two fluids and one solid phase in the highly agitated region where physical contact between the air bubbles, and the solid particles to be floated, is accomplished. The particle to be floated is assumed to have a properly prepared hydrophobic surface prior to flotation. Upon leaving the three-phase mixing region, the "floatable particle-air bubble matrix" and

Jan 7, 1982

By Raymond P. Miller, David L. Monson, Robert A. Robinson

A geotechnical instrumentation program consisting of borehole extensometers and portable tape extensometer stations was effectively used to monitor concrete liner deformations and guide construction procedures during enlargement of a 75-year old Union Pacific Railroad tunnel in Wyoming. Enlargement involved excavation of the old concrete invert and placement of 5,941 feet of new concrete invert 6 feet lower in squeezing shales, fault zones and water-bearing sandstones. Instrumentation data were used to guide procedures for excavating the old invert, installation of temporary interior struts, underpinning existing liner walls, and placing the new concrete invert.

Jan 1, 1976

By Russell. A. Smith

This paper describes some recent work on the identification and development of new chemical reagents aimed at improving the industrial processing of phosphate ores by froth flotation. In particular, three chemical product families which will be discussed appear to offer enhanced flexibility by: 1) utilizing a small amount of a silica control reagent which can significantly reduce the amount of anionic (carboxylic) collector required for a given P2O5 recovery level; 2) utilizing a new anionic collector family which offers high P2O5 recovery and selectivity versus standard carboxylic collectors; and 3) utilizing another new anionic collector family which has, in some tests, allowed for selective removal of dolomite from apatite. Examples and use characteristics of each of these new chemical ideas will be presented.

Jan 1, 1993

By James P. Connell

The Berkeley Pit of The Anaconda Company is located on the southeast slope of the Butte Hill, the legendary "Richest Hill on Earth," and is one of the largest pit operations in the world completely dependent on truck haulage. Through October 31, 1968, the Berkeley stripping and mining operations have moved more than 442,589,000 tons of material. Present scheduled production is at the rate of 260,000 tons per day, with a record quantity of 306,900 tons having been hauled on September 23, 1968. Although the Berkeley Pit has been in production only a little more than ten years, it has been the proving ground for many of the presently used large trucks. Beginning with the original R. G. LeTourneau 75-ton electric truck in 1960, Unit Rig 85- and 100-ton electric drives, Haulpak 65- and 105-ton electric drives, and Caterpillar 100-ton electric drives have all been tested under production conditions. In addition, engine development has kept pace with both 1000-hp diesel and 1100-hp gas turbine engines now under test. As the size of the Berkeley operation has grown, the truck fleet has changed in size and appearance in order to maintain economic mining costs. The original fleet consisted of forty-three 36-ton trucks with conventional mechanical drives. The present fleet is made up of eighty-nine trucks: nineteen 85-ton Unit Rig electrics with 700-hp diesel engines; sixty-nine 100-ton Unit Rig electrics with either 700- or 1000-hp diesel engines; and one 100-ton Unit Rig electric with an 1100-hp gas turbine engine.

Jan 1, 1969

By William T. Barrett

It is said that Thales of Miletus, 600 B.C.,1 was aware of the attraction of lodestone toward iron and highly magnetic minerals. However, the birth of magnetic concentration followed shortly after the invention of the first electromagnet by Sturgeon in 1825. Sturgeon's magnet was described in the annals of electricity.2 The first attempts to concentrate minerals by the use of magnets date back to about 18473 but the first commercial drum-concentrator was apparently invented by R. Cook in 1849. Credit must also be given to the invention of P. Righter's machine in 1867,5 and to the highly successful Wenström separator devised in Sweden in 1883.8 Since the advent of these early separators there have been virtually hundreds of patents granted covering minor modifications of drum-type magnetic separators. The more important advances from a technological viewpoint have been the design of stable power supplies for d.c. magnets, the advent of ceramic permanent magnets which are now replacing electromagnets for the concentration of ferromagnetic minerals, and advances in general magnet and machine configurations.7 One of the problems facing both the designer and the user of magnetic separators is the evaluation of the body forces acting on particles in the magnetic field of the separator. Perhaps the most elegant method of evaluating the body force associated with a drum-type magnetic separator is that recently suggested by W. F. Brown.8 Brown measures the radial component of the field intensity one-half inch from the drum surface and fits a Fourier series in the angle about the drum axis (Figure 1). Once the coefficients of the series are known, it is then possible to calculate [ ]

Jan 1, 1970

By Mohan Dutt

This paper is concerned with applied platinum resistance thermometry which involves many considerations absent in precision thermometry. The historical development of the Callendar-Van Dusen Equation which describes the resistance- temperature relation of pure platinum is discussed. The advantage of using platinum resistance temperature sensors over thermocouples is described, and the improvements in design and construction of these sensors that have come about in the past few years are discussed. Integral and remote bridges that convert resistance changes into voltage together with signal conditioning techniques and equipment for voltage or current signals are described. Errors encountered in temperature measuring schemes and methods to reduce these errors are summarized.

Jan 1, 1969

By C. T. Thompson

"Rotary percussion" implies two types of energy, rotary and percussion. Into these categories fall rock' drills of varying sizes. The larger ones drill above 6" diameter holes; the medium size, 2 3/4" to 4 1/2" holes; and the smallest, 1 1/4" to 2" holes. Essentially, the larger holes are drilled with doom-the-hole drills using tri-cone bits. Percussion energy evolves from the drill piston and rotation power from the rotary table or overhead drive, using drill collars or pull down mechanism to preload the bit.

Jan 1, 1963

By William E. Bruce

Percussive drill calibration experiments performed by the Bureau of Mines on two drills are described. The use of a linear velocity transducer to determine piston velocity, blow frequency, and piston stroke length is discussed. Data are presented on the relationships between maximum work rate and feed air pressure. Penetration rates in nine rock types were measured for the same two drills. Physical properties of the nine rock types are presented in tabular and graphical form to show relationships between penetration rates and physical properties. Finally, conclusions are drawn as to the potential use of these data to predict percussive drilling rates.

Jan 1, 1970

By C. K. Man

Coal dust explosions in underground coal mines are prevented by generous application of rock dust (usually limestone). If an explosion should occur, the rock dust disperses, mixes with the coal dust and prevents flame propagation by acting as a thermal inhibitor or heat sink. To investigate this process in more detail, a number of explosion experiments using various coal dust and limestone rock dust mixes have been carried out at the Lake Lynn Experimental Mine (LLEM). These were conducted in a single entry of about 1600 ft (488m) in length and initiated with a methane gas explosion. A consistent set of post-explosion floor dust samples were taken along the entry after each test. These dust samples have been analyzed in the laboratory using thermogravimetric analysis (TGA) and solubility to determine how the limestone rock dust behaved during the coal dust / rock dust explosions. The preliminary results are reported in this paper and indicate that the chemistry of limestone plays an important role in its capacity to inhibit coal dust explosions. The results also show that it may be possible to estimate the intensity of the explosion using these conventional methods of analysis. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By J. C. Norman

The boron review arrived too late to appear in the June issue. The United States was the world's second largest producer and the largest consumer of boron compounds during 1991. According to the US Bureau of Mines, boron mineral concentrate and chemical production in the US totaled about 1.1 Mt (1.2 million st), yielding about 608 kt (670,000 st) of BO, in 1991. Total estimated value was $440 million. That level of production was equal to 1990 revised production figures. Value was greater by $37 million, however, reflecting a strengthening of boron product prices. The US continued to supply essentially all its own boron while maintaining a strong position as a source to foreign markets of sodium borate products and boric acid. Domestic employment in the mining and beneficiation of boron products in 1991 remained at 1100 people, about the same level as in 1989. The Bureau of Mines estimated total world production of boron in 1991 - mineral concentrate and chemical - at about 2.9 Mt (3.2 million st). That corresponds to about 1.2 Mt (1.3 million st) of BO ,. World production in 1991 was about equal to revised 1990 levels. US production Mines and processing operations in southern California were the only domestic sources of boron mineral concentrates and chemicals in 1991. US producers, in order of quantity of production, were US Borax and Chemical Corp., North American Chemical Co., and American Borate Co.

Jan 1, 1992

All coal preparation unit operations in which fine coal is handled depend to some extent on wettability of coal surface by water. The wetting results from interactions between the coal surface and water molecules that are determined by the composition of coal matrix (interrelated with coal rank) and heterogeneous constituents such as oxygen functional groups, mineral impurities and pores. The contact angle of water on an unoxidized, homogeneous coal hydrocarbon matrix is calculated to be 100o, and much lower values measured on real coal specimens result from contributions from the heterogeneous constituents. While the effect of wettability is critical in flotation and oil agglomeration, suppression of respirable dust, and coal water fuels, it has been shown to play a significant role also in coal flocculation with semi-hydrophobic and totally hydrophobic flocculants.

Jan 1, 1995

By Wendell H. Nielson

Flotation processes contain disturbances which make material balance closures difficult to achieve. Lack of closure also arises from instrument errors. A portion of these problems can be overcome by proper equipment selection; the primary measurement installation and methods of initial data filtering are discussed below. The problem of data adjustment has been considered before (2). The technique described here is essentially that of Ripps (2). The technique was expanded to include linearization of non-linear material balance equations. An additional large error detection portion was also added to Ripp's formulation. Ripp's technique is based on a Lagrange-Multiplier optimization method. The Lagrange-Multiplier technique is generally applied when there are equality constraints on the variables. Steady-state material balance equations fit in this category. The basic Lagrange-Multiplier method is described. It is followed by a description of the modified material balance data adjustment technique. An example is presented to illustrate the use of this method.

Jan 1, 1970

By K. C. Ko

The pit slope angle dictates the economics as much as the depth of the pit. Steeper slope provides more ore reserves, at the same time, the steeper slope presents higher probability of instability and associated maintenance problems. While large open pit mines mostly belonged to nonferrous metals in the past, other mines are becoming deeper as the mine economics permits deeper mine operations, Such minerals include coal, uranium, phosphate, and others. There are some basic differences between an open pit slope and slopes that are encountered in usual civil engineering work such as dam embankments and highway cuts (Figure 1). The stability of the civil engineering slope changes continuously with time due to ground-water movements, weathering, etc. But the stability of the open pit slope (Figure 2) changes more drastically day-to-day or even hour-to-hour, These changes occur because not only is the slope geometry being continuously changed by the mining operation, but also different geology and geologic structures are being exposed on the slope. Even when a particular slope area is not presently being mined, excavation in adjacent areas can affect the general condition of that slope area. A pit will experience some slope failures during its life.

Jan 1, 1977

By Thor Skjeggedal

The Norwegian contracting firm A/S Høyer-Ellefsen has for the last 2.5 years carried out substantial pregrouting in a 7600m long tunnel just outside the city of Oslo. This has been done to avoid groundwater lowering and consequent damage to surface structures. A WIRTH TBM is used in combination with a 2 boom Atlas Copco hydraulic jumbo for the drilling of groutholes in front of the machine. The detailed procedure for the drilling and grouting will be discussed, and the results obtained will be presented.

Jan 1, 1981

By H. Schubert

The flotation of sylvite and also some accessory minerals is performed in brines containing very high electrolyte concentrations. Under these circumstances the mechanims of collector adsorption exhibit some characteristics which will be discussed by significant examples: - flotation separation of sylvite and halite with n-alkylammonium salts and n-alkyl sulfates - flotation separation of kieserite and anhydrite with acylamino carboxylic acids - flotation of halite by collectors which are adsorbed by hydrogen bond formation.

Jan 1, 1988

By A. L. Coello Velázquez

The subject of this paper is particle population balance models (PBM) that describe mineral impact crushing behavior; it is mainly concerned with the selection and fragmentation distribution function due to their importance in this context. The data obtained by Datta (1999) by applying impact pendulum testing to single limestone particles, used by Austin (2002, 2004a and 2004b) to obtain the principal parity of fragmentation functions, were processed in order to compare them with the results of other authors, such as Nikolov (2002 and 2004) and Vogel and Peukert (2003 and 2005) so as to increase knowledge of impact crushing. From this data it has been possible to obtain the performance models of the principal parameters of fragmentation function, thereby reducing the number of experiments necessary to model the impact crushing process. The authors also propose a simplification of the selection function model posited by Austin (2002).

Jan 1, 2011

By Wilhelm J. Kogelmann

The concept and operation of novel shaft sinking systems utilizing roadheader-type cutter booms, including mucking, conveying, and hoisting installations, are described. Selection criteria, performance data, and economic considerations for various shaft excavators are presented. Various applications of this low-cost and flexible system for civil engineering and mining projects will be discussed. The cutter booms can work in both soft ground and competent rock. Furthermore, the novel excavator can operate in ground stabilized by grouting, cementing, and freezing. The flexible cutting system can be used both for excavation of shafts, foundation pits, slopes, and for tunneling (drifting).

Jan 1, 1989

By Shijie Wang

The metals of value in tetrahedrite are copper, antimony and silver. A new hydrometallurgical process is proposed to recover these metals from tetrahedrite. The process consists of leaching concentrate with ferric fluoborate, solvent extraction, electrowinning and residue treatment. Products from this process are high-purity SX-EW copper and antimony and a high-grade silver residue that will be further treated in a hydrometallurgical process for early release of silver. The process has advantages, such as achieving rapid leaching rates at modest temperatures with high metal recovery. Most pyrite is not attacked. Thus, it remains in the leach residue along with elemental sulfur.

Jan 1, 2003

By Robert G. Page

"Stabilization" of copper differs from sin in at least one respect - no one seems to be against it. Every time a tycoon in the producing industry pontificates on the economic history of copper, or prophesies its future, he is likely to praise the virtues of "stabilization". Consumers of copper constantly bemoan fluctuations in the supply and price of the metal. Governments in some producing countries, to a greater or lesser degree dependent upon exports of copper for foreign exchange and upon taxation of copper profits for substantial parts of their budgets, are perhaps more eager than any other group for "stabilization".

Jan 1, 1962

By L. A. Henry

The island of Jamaica consists predominantly of Carbonate rocks which vary in chemical & physical characteristics. Currently these rocks are used for construction and road aggregate, landfill and as a raw material in the manufacture of cement. Over the past fifteen years the Geological Survey of Jamaica with assistance from a number of international aid agencies and the private sector have identified deposits of high calcium/high brightness limestones which have the potential to be utilized as a high quality filler and a number of other commercial applications. Geologically, these limestones are formed within the Eocene Swanswick Formation, the Oligocene Walderston-Browns Town Formation and to a lesser extent the Miocene Montpelier and Newport Formations.

Jan 1, 1998