Search Documents

By L. A. Puchkov

The creation of automatic methane concentration control systems presupposes the use, as a control factor, of the air rates in workings and in mine as a whole. These systems present a complicated set of computers and software, including as major components the following - systems for detecting methane concentration and air rate; - telemechanics systems; - programs and means of data processing; - programs and means of air rate control in workings and main fan capacity control. The paper analyses the experience of development and exploitation of automatic methane control system in gassy mines of the USSR Donetz coal basin. Much attention is given to the study of technological factors influence upon aerogasdynamic process using automatic methane control system.

Jan 1, 1989

By D. A. Curry

This paper describes a study of the influence of non-normal loading on the indentation behaviour of single bit-teeth. Indentation experiments have been performed on a soft, isotropic limestone using both sharp and blunt 60 degree wedge-shaped indentors constrained to penetrate the rock at 0, 15, and 30 degrees to the rock surface normal. For both sharp and blunt indentors, the normal force required to produce a given normal penetration decreased as the offset of the penetration direction from the rock surface normal increased. The crater volume produced by a given normal penetration with the sharp indentor was largely independent of the penetration direction. In contrast, the crater volume produced by the blunt indentor was increased markedly by non-normal penetration at small penetration depths, because the threshold penetration for chip formation decreased with non-normal loading. The crater volume produced by a given normal force was significantly increased by non-normal penetration, and this increase was particularly pronounced with the blunt indentor. The energy required to form unit crater volume was correspondingly reduced by non-normal indentor penetration. A simple method for predicting the reduction in the rock's resistance to chip formation is outlined, which is supported by the experimental data. The implications of these findings for rotary drilling are considered.

Jan 1, 1986

By M. T. Webster

Views about the proper aim of public policy are, of course, matters of perspective and debate. Regardless of perspective, one would assume some consensus around the view that public policy ought to encourage mine operators to seek independent and critical assessments of worker safety and health at their operations through voluntary auditing. However, a review of the law on this topic shows that there is little to no manifestation of such a policy. Indeed, the balance of this paper, with a couple of exceptions, is devoted to the existing legal pitfalls that should be considered before a safety and health audit is conducted at a mine. While attorneys, particularly litigators like the author, might tend to focus on the potential problems that could arise from any given situation, the fact that most of this paper is devoted to potential legal concerns associated with auditing is a realistic reflection of the current state of the law. Specifically, this paper addresses the interplay between voluntary safety and health audits conducted at mines regulated by the Mine Safety and Health Administration (MSHA), and the administrative and civil legal issues related to such audits. The paper first provides an explanation of how and by whom an audit is conducted. The paper also addresses whether voluntary safety and health audits may be considered privileged and kept confidential in administrative and civil proceedings. Finally, selected legal issues related to such audits that could arise in administrative and civil litigation are discussed.1

Jan 1, 2012

By Ahmed Yehia, M. A. Abdel-Khalek, J. D. Miller, M. Fadel

Recently, research efforts have been made to lower the magnesium content of phosphate rock concentrate to be a suitable feed for phosphoric acid production and other related industries. Among these efforts is the bioprocessing technique. However, this study is devoted to study of using an enzyme, extracted from coffee waste, as a surface modifier during the fatty acid flotation of calcareous phosphate rock. A mixture of oleic acid and kerosene was used as collector. Factors, which affect the enzyme activity such as enzyme dosage, solution pH, temperature and conditioning time, were studied. Under the appropriate conditions, a concentrate product containing less than 0.60% MgO was achieved from the Abu Tartur feed (1.80% MgO) with a P2O5 recovery of more than 94%.

Jan 1, 2002

By J. K. Mohanty, D. Panda, P. K. Sahoo, R. K. Paramguru, K. C. Nathsarma

Ferromanganese slag, a product of the manganese industry, was characterized mineralogically. The slag, which contains high Mn values, was characterized using optical microscopy, XRD analysis and electron microscopy. No separate Mn-bearing oxide mineral phase was found. The slag is amorphous, and no crystalline phase was identified in the hulk sample by XRD, However, in. fine fractions, quartz was identified. Scanning electron microscopy (SEM) revealed the presence of Mn, Si, Al and Ca in the matrix without the development of a mineral phase. Leaching experiments using H2SO4 were carried out to determine if Mn could be extracted from the slag. At room temperature, almost 100% of the manganese could be dissolved at a solid-liquid ratio o f 1:10 by leaching with dilute sulfuric acid. The impurities could be precipitated by pH adjustment to produce a manganese sulfate solution suitable for the production of MnO2 or electrolytic Mn metal. Based on the laboratory-scale experiments, a suitable process is proposed to recover manganese values from the, ferromanganese slag.

Jan 1, 1999

By Henry B. Estabrooks

As was the case with many other mining companies, the management of Tennessee Copper Company' viewed with some interest reports in various trade and technical journals of the successful use of ammonium nitrate-fuel oil mixtures as an explosive in coal stripping., construction, open pit mining and finally in underground salt mines. The apparently simple transition from the "interested" stage to a point where in excess of 80% of the ex¬plosives used is ammonium nitrate may be of interest. The Tennessee Copper Company operates five mines in the "Copper Basin" of Polk County which lies on the extreme southeast corner of Tennessee. The ore is a massive sulfide principally pyrrhotite and pyrite with some tough lime silicates as gangue while the walls are greywacke interbedded with schist. Average total production is 28,000 tons per 5-day week and an average of 422 feet of development per week. Development work consists of 8'x 8?, 6?x 7?, 5'x 7? and 4'x 6? drifts driven with drifter drills using 1-5/8" carbide detachable bits and 5'x 5' raises driven with stopers using 1-5/8" bits.

Jan 1, 1962

By W. R. Reed, J. P. Rider

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a medium-sized surface blasthole drill shroud with a dry dust collector system. CFD models were constructed in ANSYS FLUENT Version 15. Previously run experiments conducted in the NIOSH full-scale drill shroud laboratory were utilized to validate the models. The setup values in CFD models were calculated using experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for test scenarios, including 0.14 m3/s (300 cfm) bailing airflow with 2:1, 3:1, and 4:1 dust collector-to-bailing airflow ratios and 0.24 m3/s (500 cfm) bailing airflow cases with 2:1, 3:1 and 4:1 dust collector-to-bailing airflow ratios. For the 2:1 and 3:1 ratios, results showed the calculated dust concentrations from the CFD models were within the 95% confidence intervals of the lab experimental dust concentrations. This paper describes the methodology used to develop the CFD models, to calculate the model dust input, and to validate the models based on experimental data. Problem regions were identified and revealed by the simulation of a dry dust collector system. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. INTRODUCTION In surface mines, production drilling is an essential process in blasting which fractures the hard rock overburden for removal. Holes with a predetermined pattern, diameter, and depth are drilled into the overburden to introduce explosives. During the drilling process, considerable amounts of respirable dust are produced. Past research conducting area sampling at blasthole drills has documented time-weighted average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 [1] and 1.04 to 52.30 mg/m3 [2]. These high dust concentrations, which may contain silica, can lead to respirable dust over-exposures for the drill operator, drill helper, and other personnel in the vicinity. These over-exposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal. In order to prevent the development of silicosis to mine workers, the Mine Safety and Health Administration (MSHA) regulates the exposure to respirable dust. For metal/nonmetal (M/NM) mines, MSHA has adopted the threshold limit values recommended in 1973 by the American Conference of Governmental Industrial Hygienists (ACGIH) [3]. The total airborne dust standard is 10 mg/m3. However, if the sample contains greater than 1 percent quartz (the most common form of crystalline silica), a respirable dust standard is calculated with the following equation: Respirable dust standard = (10 mg/m3) / (% respirable quartz + 2)"

Jan 1, 2016

By S. Chander

The formation of surface films on pyrite has been studied through electrochemical techniques of cyclic voltametry and AC impedance measurements. The characteristics of the surface films depend upon the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance showing a certain degree of passivity. Some pyrites show more passivation than the others, however. On oxidation, metastable phases of Fe(OH2) and Fe(OH3) form which transform to more stable 3 phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics which is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide rather than sulfur because the later is expected to be limited to a monolayer in alkaline solutions. This study has also demonstrated that AC impedance measurements can be used to study the growth characteristics of films at mineral/ solution interfaces.

Jan 1, 1987

By S. L. de Moraes

This study aimed to identify a way to reduce the use of bentonite in the pelletization of magnetite. With this goal, different combinations of binders were compared to bentonite by examining the quality of pellets obtained by balling drum agglomeration. Pellets were subjected to routine tests that included simple compression of the wet and dry 105°C pellets, dropping wet pellets to determine their ability to survive handling and submitting pellets to thermal shock to determine how they tolerate drying and preheating. The best results use sodium silicate (1.5%) as a binder and show that it is possible to pelletize iron ore without using bentonite.

Jan 1, 2010

I met Austin Taylor in Vancouver on my way home from my first Pioneer examination. He asked me to examine the unsuccessful old Lorne mine, adjoining and west of the Pioneer. I had no idea that this meeting would lead to one of the outstanding successes and pleasant associations of my career. I knew nothing of Taylor, except that Gen. McRae and associates said that he had been engaged in lumbering and was interested in an oil and gasoline marketing company called Home Oil. But even if the Lorne examination would be only a small one, in the depths of the Depression in 1931, I was glad to have a chance to look at another gold property, so I agreed to visit the Lorne early in August. The start of the trip was not auspicious. I had been working hard on an unproductive study, and was greatly worried by my father's hopeless illness with tuberculosis. To get a little rest on my way north I had arranged to go from Seattle to Vancouver on the night boat that connected with my train. To my surprise, Bill Boultbee, an associate of Taylor, met me at the train in Seattle at 9:30. He said he would drive me to Vancouver, arriving at one In the morning. I was so tired that I begged off and let him take the drive alone Boultbee was most understanding and friendly, but I knew how I would have felt if I had been kind enough to take the long drive to help a stranger and then had been forced to make the return midnight drive alone. I was lucky they did not call off the examination at once. I got a good sleep on the Vancouver boat and Austin Taylor met me at the Hotel Vancouver for breakfast. After a brief talk he took me to the small steamer that made the 4-hr sail up Howe Sound to the village of Squamish. This was the end of the Province-owned Pacific Great Eastern Railway that was eventually to be a shortcut from Vancouver to the Canadian National main line at Prince George. Because

Jan 1, 1976

By Wilbur I. Duvall

This paper discusses general principles of underground opening design based on the concept that with the necessary input data regarding the geology of a site, the physical properties of the rocks, the in situ stress field in the rock and the general geometry of the underground openings, the rock formation can be classified into six major categories which are useful for design purposes. Using simple theories for the criteria of failure for rock In compression and tension, general elastic theory for stress concentration around openings and In structures, beam theory for stability of roof rock, and elementary inelastic theory for creep phenomena, basic design techniques are outlined for the various rock classifications. The need for field evaluation of the theoretical design is stressed and some general techniques that should be used in these field evaluations are discussed. Where appropriate, the need for additional studies and research is noted.

Jan 1, 1977

By W. Robert Power

Stone is considered by many to be the premium material for beauty and durability in all kinds of construction. Its use dates to the dawn of civilization and only buildings made of stone have survived from ancient times. The use of stone relative to other materials declined from the beginning of the present century reaching a low point in the third quarter, but there has been a resurgence in the use of stone in construction during the past decade, due probably, to new techniques for producing stone, a greater recognition of its beauty and durability, and greater affluence among consumers. The aesthetic appeal of stone is attested to by the many attempts to simulate it in synthetic materials. Today, natural stone is considered by many to be the ultimate in aesthetic appeal, durability, and ease of maintenance. Consumption of dimension stone has increased dramatically during the past decade. The US Bureau of Mines reported that the total value of US consumption in 1978 was $1 13 million and that total imports were valued at $65 million in 1979 (Anon., 1980). In 1989 consumption of domestic dimension stone was valued at $208.3 million and imports at $525 million. This dramatic increase occurred after demand had decreased at an average rate of 2.5% in the two decades prior to 1978 (Anon., 1980). More than half of the imports come from Italy, but production of dimension stone has increased worldwide spectacularly. Meaningful statistics on dimension stone are hard to acquire. The finished piece of stone is a highly value-added product, but stone may be sold as rough blocks, sawed slabs, or finished product. The same piece of stone may therefore be sold and reported three or more times. Furthermore, although the quantity of stone is most commonly reported in tons, stone cladding is more often sold by the surface area and at the same price for different thicknesses. By any measure, however, the production and consumption of dimension stone has increased dramatically during the past decade. A significant indication of the resurgence of stone was the introduction of two new trade publications during the 1980s. Stone World (Tradelink Publishing Co., Inc., Oradell, NJ), introduced in 1984 is published monthly and Dimensional Stone (Dimensional Stone Institute, Inc., Woodland Hills, CA), introduced in 1985 is published monthly. Both magazines provide useful information on new technology, market trends, producing areas and companies, and other information not previously available.

Jan 1, 1994

By Albert E. Ketler

The techniques for fire monitoring of conveyor belts in underground coal mines have been revolutionized by the advent of sensitive carbon monoxide sensors and computer monitoring systems. These new systems are rapidly replacing the previous thermal (fixed-point temperature) sensors that have been shown to be considerably less sensitive for early fire warning. CO is generally an excellent indicator of spontaneous combustion. However, the most recent non-flammable conveyor belt materials have been shown to "burn" with dense smoke, but without sufficiently high temperatures to produce much carbon monoxide. To cover this fire detection void, a smoke detector was developed to augment CO sensing for these new conveyor materials. However, computer monitoring provides the flexibility for handling this and other additional instrumentation as fire monitoring techniques evolve. CO, smoke and temperature sensing may eventually be advocated for complete fire monitoring.

Jan 1, 1987

By Steven McCutcheon

As most of us have learned through prior and often frustrating experience, anyone proposing to construct a new or expanded mining-ore processing facility must first contend with a rather complex array of environmental laws and permitting regulations administered by a number of different Federal, State and local agencies. At our lost count, there were about 55 federal enactments affecting base and precious metals projects. Applicable State and local laws will usually increase that number significantly. The time and costs associated with complying with all these various regulatory programs usually constitutes one of the major areas of uncertainty in the development of a proposed project. There are many in the mining industry who firmly believe that these environmental regulation and permit programs necessarily causes significant delays and increased costs in the development of a project. This belief, unfortunately, is probably a result of a basic misunderstanding of how the environmental permitting and regulatory system actually works.

Jan 1, 1984

By J. Oliver, J. Cleason

"With maintenance costs rising and an increasing demand for higher production, the use of sealed spherical roller bearings can reduce maintenance costs while providing increased production uptime. The sealed spherical bearing has increased bearing life by slowing the ingress of contamination. This paper will describe how contamination and bearing wear is reduced by reviewing case histories from coal and metal mines that improved their production by decreasing downtime using sealed spherical roller bearings. INTRODUCTION The spherical roller bearing (SRB) is a robust rolling element bearing that can accommodate high radial loads, low to moderate axial loads, and misalignment with no loss in carrying capacity. (i.e. Figure 1) Because of these characteristics, it is a favorite in mining applications and many other heavy industry applications. Primary applications are the various pulleys on conveyors. Coal and hard rock mines have hundreds of miles of conveyor lines and countless head, tail, drive, and idler pulleys. Maintaining the bearings on these pulleys and replacing bearings that have failed can be a huge expense to a mine in components, labor and downtime. Ideally, the bearings are replaced when the pulley is changed out according to the maintenance cycle, about every 4 years. Reality, however, causes the bearings to be changed out every year, or sooner. These premature bearing replacements can cause production shut downs for as long as 8 hours. Conveyor pulleys have been targeted at many mines as the single biggest maintenance pain point.The primary reason for replacing conveyor bearings is internal wear from fine, solid particle and water ingress through the bearing housing seals. (i.e. Figures 2 & 3) Traditionally, the bearing is mounted in a split pillow block housing (SAF, FSAF, SDAF or SNL are typical industry styles) with only labyrinth seals (LER/LOR) for protection against the ingress of contaminants. The bearings are lubricated with grease. A common way to extend the MTBR is to purge the bearing system with large quantities of grease to flush out the contaminants. If the bearing, and thus the housing seals are not frequently purged with grease, fine solid contaminants enter the housing and bearing through the labyrinth cavities."

Jan 1, 2015

By K. Hanna

Early identification of adverse geologic conditions and high stress concentrations during the high-speed extraction of coal using modern mechanized long wall systems is a major challenge facing the mining industry. Often, unexpected geologic anomalies that affect rock mass quality are encountered more rapidly, leaving the mine operator with insufficient time or information to deal with the changing ground conditions. The RockVision3DTM seismic tomographic system, developed by NSA Engineering, Inc., offers substantial benefits over conventional geologic/stress-detection methods and has been used successfully in coal mines worldwide. Tomographic images, produced economically and in near-real time, are easy to interpret, allowing mine operators to deal with potential hazards on a day-to-day basis. This paper focuses on the application of RockVision3DTM technology for delineating hazards caused by stress and geologic anomalies. Case studies for two bump-prone coal mines will be discussed. For example, (1) in a German deep (>1,130 m) mine, the drilling-yield method was used to verify the effectiveness of this technology in detecting stress anomalies ahead of longwalling; (2) in a Polish mine (-500 m deep), two longwall panels 4 km apart were monitored to assess structural and stress-related factors contributing to differences in mining conditions and magnitude of structural failures.

Jan 1, 1999

By Wm. Terry Siemer

Abstract. The value of industrial rocks and minerals produced in New Mexico in 1978 exceeded 227 million. 1e state ranked first in the nation in production of potash and perlite and was a leader in pumice production. Other commodities with sizable production in New Mexico include barite, caliche, clay, dimension stone, fluorspar, gypsum, humate, limestone, mica, salt, sand and gravel, scoria, and silica sand Non metallic resources are distributed throw out the state, but development and exploitation is concentrated in western and southeastern New Mexico. The value of industrial rocks and minerals within the state grew about 9 percent to more than $227 million in 1978. Continued growth, however, depends on continued demand, exploration, and development.

Jan 1, 1980

By R. Schwarz, E. Pusch, A. Juch

"The paper describes in general the objectives, goals as well as theoretical background of "METSI"-project proposal submitted to German BMBF (Federal Ministry of Education and Research). The METSI project is a starting point for technology and know-how transfer of German water management and water treatment technologies to South African Mining industry. "METSI" is Setswana, one of the eleven official languages in South Africa, and means "water". It stands also for "Management System for the Implementation of Environmentally Sound Water Supply Technologies in South African Mining Areas with Involvement of all Relevant Stakeholders". The project focuses on development, design and implementation of mathematical models that consolidate and evaluate existing data and generate substantiated projections of "water" amount and quality. METSI covers a wide range of scientific, technical, social as well as economic questions related to "water in mining"."

Jan 1, 2011

By R. E. Driscoll

The exploration, geologist of necessity has to have a wide working knowledge of many specialties other than hiw own, First he has to use his own technical background to find a deposit,, of a mineral that is of interest, Once found, his problems are Just beginning, He then has to assume the role of an economist, an accountant, a mining engineer, a chemist, a metallurgist,, a salesman and what-have you, In the economic field, he must determine the marketability of either the ore or the refined mineral. He must gauge the supply and demand for the particular mineral he is interested in and make his best guess as to ultimate cash flow from a deposit over the estimated life of said deposit, He must then assume the role of a mining man and estimate cost of recovery, including an, evaluation of the most economic mining method, cost of supplies and labor, and again estimate a net cash flow. He must then determine amenability of ore to economic metallurgical methods, he must determine the legal status of the property involved and, after analysis of the specific situation, determine the best approach to a deal, After all of this he must sell it to the people who will put up the money and then put his deal together and sell it to the people who own the minerals, if that be necessary. Then he has to sit back, with crossed fingers and crossed legs wondering for some months, and in many cases even years, whether or not he is right. The expenditures required to open up a mine in this day of wild inflation are such that he has to be right, and the responsibilities are awesome.

Jan 1, 1958

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984