Search Documents

By Rollien R. Wells

The Bureau of Mines was created in 1910 by an act of Congress and subsequently directed to: "...conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment, and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources through the prevention of waste ..." Under this broad charter, the Bureau's responsibilities have changed and grown from an almost exclusive concern with coal and coal mine safety to the present emphasis on a full spectrum of mineral producing and consuming problems. In the past 30 years, the domestic consumption of coal, oil, gas, metals, and industrial minerals has more than quadrupled, in parallel with the rapid and enormous growth in industrial production. Of the scores of metals and nonmetals essential to the Nation's progress and security, many are scarce and difficult to wrest from domestic sources. Reserves of some ores are dwindling. Available ore resources are becoming leaner and more difficult to treat. In recognition of this many faceted problem, the Bureau has engaged in a continuing quest for new and improved technology to enable economic exploitation of marginal minerals and fuels, to find substitutes for minerals in short supply, and to create better materials to meet the expanding and diverse requirements of the growing economy. The current central concern of the Bureau is focused on meeting projected fuel, metal, and mineral demands at the lowest real cost by recovery from available resources by new and improved technology that minimizes waste, hazards, and social and environmental problems.

Jan 1, 1970

By Felicia F. Peng

Flotation process is particle hydrophobic surface-based separation technique. To improve the essential flotation steps of collision and attachment, and reduce detachment probabilities between air bubbles and hydrophobic particles, a selectively designed cavitaion venture-tube can be used to generate very high numbers of pico-nano bubbles to flotation column. Fully embraced by those high numbers of tiny bubbles, hydrophobic particles are readily attracting those tiny bubbles to their surfaces. The results of column flotation of Pittsburgh No.8 seam coal are obtained in a 50 cm ID and 162cm height flotation column equipped with static-mixer and cavitation-venture tube, using kerosene as collector and MIBC as frother. Design of experiment procedure combined with statistical two-stepwise analysis method are applied and attempted to made the optimizing the grade and recovery. The effect of independent variables on response has been explained. Combustible material recovery of 85-90% at clean coal product of 10-11 % ash are obtained from feed of 29.6% ash, with reduced amount of frother and collector than that used in conventional column flotation. The column flotation process utilizing the pico-nanobubbles can also be extended to the lower limit and upper limit of particle size ranges for better recovery minus 75 µm and 300-600 µm, respectively.

Jan 1, 2013

By Lee W. Abramson, Kenneth P. Akins

The authors have accumulated published data on residual soil and rock tunnels in the United States and have compared it to transit tunneling experience in Atlanta, Georgia, and tunnels in other soil and rock conditions. Two 6.1 meter (20 foot) diameter shield driven, compressed air tunnels were constructed for the Metropolitan Atlanta Rapid Transit Authority (MARTA) connecting the Five Points Station (central hub) with the Peachtree Center Station (first station on the north line). Because of the historic multi-story structures above the tunnels and the variety of subsurface conditions, a comprehensive ground monitoring and observation program was conducted. Conclusions are drawn regarding residual soil and rock ground response due to tunneling. Comparisons are made to ground response due to tunneling in other soil and rock conditions.

Jan 1, 1983

By P. Klaus

"KfW IPEX-Bank is the commercial arm of KfW Bankengruppe, responsible for international project and export finance.KfW was one of the first banks in Germany to promulgate environmental guidelines for its commercial business activities. These guidelines were first made public in 2000 and updated for the second time in 2004. They now include specific reference not only to environmental but also to social concerns. The guidelines specify the procedures to be followed in assessing credit risks related to environmental or social hazards.The bank considers sustainability as an interdependent framework of economic, ecological and social factors. In its efforts to contribute to sustainable development worldwide the bank uses its influence as far as possible to improve a project’s performance if such improvement is deemed necessary."

Jan 1, 2005

By Richard L. Wedertz

Although the physical appearance of excavating equipment doesn't seem to have radically changed over the past decade, important changes within the products and an innovative attitude on the part of the engineer in his design approach is becoming increasingly evident. The new philosophy is to go beyond simple refinements of existing designs that simply produce a machine which further reduces overall cost per ton or per cubic yard of material moved and to do it more efficiently than ever before. Standard ideas and preconceived notions have been discarded and have given way to providing a design and a machine that is best suited to get the job done. Understanding that the application will not always fit the machine, but, in most cases, the machine should fit or suit the application is a foremost consideration in the engineers' design criteria.

Jan 1, 1973

By F. L. Wilke, J. Fabian, D. Oravec

The task of production planning in ore mining is primarily con¬cerned with the removal of ore blocks within planning periods spread over the life of the mining operation. The investigation of this problem in the past resulted in the introduction of computer based optimizing techniques for production scheduling and se¬quencing. Although these techniques succeed in computing an "optimal" mine output for one planning period, they usually fail in composing a practical and feasible mine plan over the periods in concern. This paper describes conventional production planning based on operations research and the capabilities of a knowledge-based approach. An example of a planning system for the Slovak under¬ground iron ore mine Nizna Slana will be presented. By combina¬tion of these two techniques this system should improve the qual¬ity of planning procedures.

Jan 1, 1996

By John A. Brooks

The description of a phosphate flotation operation is repeat information for many people, except for variations in flow sheets. This paper is written to show the variations in flows, and to give enough. of the overall flows to allow anyone not familiar with the operation to be able to formulate a fair idea of the operations.

Jan 1, 1962

By T. Shungu, N. Vermaut

The various copper-cobalt ores mined by Gecamines, together with typical plant applications and results, are briefly described. Intensive laboratory investigations have been undertaken in recent years to improve the metallurgical performances of the various concentrators. As a result of these tests, it was shown that the flotation of the siliceous oxide ores could be improved by increasing the efficiency of the palm oil collector (energetic conditioning, chemical emulsifier, petroleum sulfonate addition) and by varying the froth depth in the cells. A new flowsheet incorporating these modifications and a regrinding stage has been approved for the rehabilitation of the Kolwezi concentrator. For what affects dolomitic oxide ores, hydroxamates were tested as secondary collectors and, based on successful laboratory results, plant trials were run but failed due to excessive frothing. In other plant tests, xanthates were replaced by a xanthate- fatty acid mixture; plant trials over more than one year proved successful for copper, but not for cobalt. Mercaptans were tested as secondary collectors for the sulfides flotation from sulfide or mixed oxide-sulfide ores; laboratory results proved successful but, to date, no plant test has been run.

Jan 1, 1987

By J. Mattern

Performance monitoring, operational practices and ongoing collection of geologic data in open pit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike open pit has been ongoing since the early 1980’s, with its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls. With the proper available equipment, steepening of bench face angles via pre-split blasting is not an uncommon method for steepening of inter-ramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted resulting in quantified, rock specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2 degrees on a 300m high slope, without the necessary purchases and procedural changes that would be required for pre-split drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves. Location The Goldstrike open pit is located on the Carlin Trend gold belt in northeastern Nevada USA (Figure 1). The mine has produced over 43 million ounces (1.2M kg) of gold during the past 30 years. Engineering Geology Stratigraphy Figure 2 is a stratigraphic section of the rocks in the Goldstrike open pit. Quaternary alluvium and Miocene materials typically are poorly indurated stiff soils and are not present in all locations. Bedrock units consist of siltstones, mudstones, sandstones and cherts. From top down the major units exposed in the open pit are the Vinini Formation, the Rodeo Creek Unit, and the Popovich Formation. In general, rock mass strength increases with depth.

Jan 1, 2019

By S. K. Kawatra, J. E. D. McDonald, S. C. Roache

"The formation of geopolymers from mine tailings using cold-bonding processes is known to be possible. Numerous cold-bonding methods exist, but the hydrothermal processes involving high temperatures and pressures in the presence of steam have been found to be the most ideal. This paper presents the results of successful preliminary studies to apply hydrothermal bonding processes to mine tailings agglomerates. Particle-size analysis revealed the particle size of the tailings waste to be 80 percent passing at 35 µm. The compressive strengths of the tailings pellets were shown to increase with time in the curing vessel, closely approaching the 400 lbf of standard iron ore concentrate pellets. These strengths are sufficient to allow use of the tailings pellets as aggregate materials for asphalt and cement. Additional applications may be possible, including reprocessing to extract more valuable materials and usage as agglomerated road-bed materials, backfills for building foundations, and replacements for sand and lime in cement.IntroductionMine tailings are a waste byproduct of ore concentration and are available in large quantities across the world. Despite their abundance, they have received little attention or consideration for beneficial use. One reason is that the chemical nature of the material is not well known. Another factor that has hindered direct usage is the fine particle size. This raises the questions: what is the composition of the tailings, and how can such fine solids be beneficially used? Because the mining industry produces concentrates, the tailings may be treated as concentrates and processed in the same fashion, but it would be inefficient to consider full sintering or induration conditions for materials that have little ore content. To achieve sustainable operation, the development of technologies to use these tailings is necessary. Mine tailings should not be considered waste, and an “out of sight, out of mind” mentality does not represent a sustainable solution for the future.One iron ore mine in Michigan is estimated to have accumulated more than 400 million metric tons of tailings during its last 30 years of operation, with an additional 180 million metric tons accumulated before the ore body is depleted. These mine tailings currently have no practical use, largely due to a scarcity of knowledge of their true physiochemical nature. It is thought that lack of quality control of the waste material prevents its use, but variability in the unprocessed ore prevents a consistent waste stream composition. The fact that the tailings are available in such great quantities makes them an extremely attractive resource. However, developing a sustainable, low-cost means of repurposing the mine tailings waste as a construction material may only be completed once the tailings are physically and chemically understood. Due to the high silica content of the material studied, cold bonding was determined to be the most viable method for processing the tailings into a usable product."

Jan 1, 2016

By James E. Monsees, Richard J. Proctor

INTRODUCTION Los Angeles is one of the world's largest cities in area with a span of 70 km between its north and south limits. The population in the Los Angeles Basin exceeds 11 million people. Los Angeles is second only to New York City in density of U.S. urban population and it operates one of the largest city bus fleets in the world, 2,500 buses. After many years of planning and many consultants' reports, it is planned to initiate a 30 km (18.5 miles) starter line subway -- the "Wilshire Corridor" (Figure 1). Construction is to start in 1985. In several locations, subway routes ultimately will skirt or cross old oil fields, which may cause gassy tunneling. Of particular note are the La Brea Tar Pits, which overlie a part of the old Salt Lake oil field. Tunneling through tar sands for about 3 km will be unique for subway construction and will occur on the starter line. Experience with previous gassy tunnels in the greater Los Angeles area shows that tunnels can be completed safely if precautions are taken. Abundant ventilation is the main solution, although other precautions are discussed herein.

Jan 1, 1985

By Warfield Garson

Few, if any, of the non-ionizing radiation health hazards to be found in either surface or underground coal mining are uniquely different because of their being found in the work environment. Hence, they can be considered generally for their bio-effects on the worker when found in the mining work environment. The same may not be said, however, for the lack of non-ionizing radiation and its bio-effects, particularly as it relates to underground coal mining. The term "non-ionizing radiation" refers to various forms of electromagnetic radiation of wavelengths longer than those of ionizing radiation. As the wavelength gets longer the energy of electromagnetic radiation decreases. Therefore, all non-ionizing forms of radiation have less energy than cosmic, gamma, and X-radiation. In order of increasing wavelength, non-ionizing radiation includes ultraviolet, visible light, infrared, microwave, and radiofrequency radiations. The energy frequency and wavelength range of both the ionizing and non-ionizing electromagnetic forces are shown in Table I. To convert the wavelengths of various radiations to Ångström units, one multiplies millimicrons by ten. In a vacuum, all electromagnetic radiation has the same velocity, namely 3 x 1010 centimeters per second. The natural source of radiant energy here on earth is our sun which emits radiation continuously over a wide spectrum. This radiation on average reaching earth ranges from 290 nm in the ultraviolet range to over 2,000 nm in the infrared range with a maximum intensity of about 480 nm in the visual range. You will note this falls into the visible blue wavelength and accounts for our blue sky and blue ocean and deep water effects. We are all familiar with the fact that the passage of solar radiation through the atmosphere to the earth changes the spectrum considerably because the atmosphere absorbs and scatters many of the sun's rays. The ozone in the upper atmosphere absorbs the shorter ultraviolet wavelengths and water vapor absorbs some of the infrared wavelengths. Smoke, dust particles, gas molecules and water droplets scatter the rays, especially those of shorter wavelengths. In addition to the sun, every gas, liquid or solid object at a temperature above absolute 0° radiates energy. Solid objects emit almost continuous spectra. At low temperatures only radiation of the longer wavelengths in the infrared range is emitted, but as the temperature of the object is increased, more and more of the shorter wavelengths are added. This fact is most readily demonstrated by heating a piece of steel. When a piece of steel reaches a temperature of about 1,700° Fahrenheit, it gives off radiation at the red end of the visible spectrum and appears dull red. As the temperature is further increased, the shorter rays are also emitted, until at about 2,100°F, the metal appears white, due to the emission of wavelengths throughout the entire visible range. Gasses, on the other hand, when heated emit radiant energy only at certain wavelengths, which are characteristic of their chemical structure. This latter fact is of importance in underground coal mining as high intensity gas and vapor lamps are becoming more and more utilized for illumination in underground coal mining. The biologic effect of non-ionizing radiation exposure depends upon the type and duration of exposure and on the amount of absorption by the miner. The effects of this radiant energy on the miner fall into four distinct types: (1) the heating effect of infrared radiation, (2) the effect on the eye of visible radiation, (3) the effects of ultraviolet radiation, and (4) the growing potential effects of the misuse of microwave radiation. Each non-ionizing type of radiation will be considered individually. ULTRAVIOLET RADIATION The sun is the major source of ultraviolet radiation, which is of concern in open pit and surface mining at certain seasons and in certain climes necessitating protection for the surface miners under those conditions; nonetheless, there are some man-made sources such as electric arc lights, welding arcs, plasma jets, and special ultraviolet bulbs for illumination underground that demand surveillance in the underground environment to be aware of whether the miners are at risk above the threshold limit values allowable. Since ultraviolet radiation has little penetrating power, the organs that are affected are the skin and the eyes. Ultraviolet radiation is strongly absorbed by nucleic acids and proteins, and the effects in man are largely chemical rather than thermal. Short-term effects on miners include acute changes in the skin. These are of four types: (a) darkening of pigment, (b) erythema (sunburn), (c) increase in pigmentation (tanning) and (d) changes in cell growth. Ultraviolet radiation also causes acute effects on the tissues of the eye. Overexposure can lead to keratitis, inflammation of the cornea, and conjunctivitis. Long-term effects of ultraviolet exposure include an increase in the rate of ageing of the skin with degeneration of skin tissue and a decrease in elasticity. Late effects of ultraviolet on the eye include the development of cataracts. The most serious chronic effect of ultraviolet exposure is skin cancer. Ultraviolet radiation effects are increased by some industrial materials and drugs. After exposure to such compounds as cresols, the skin is exceptionally sensitive to ultraviolet radiation. Photosensitivity reactions occur after exposure to a variety of other chemicals and drugs including dyes, phenothiazines, sulfonamides, and sulfanylureas. On the other hand, we must remember that ultraviolet radiation has an important role in the prevention of rickets. Vitamin D is produced by the action of

Jan 1, 1981

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By Judson H. Whitman

To evaluate intelligently and to market a source of rare earth raw material, it is necessary that the producer understand the requirements of the processor and the manner in which these requirements effect the value and salability of his product. This paper will be an attempt to aid in such an understanding. The majority of rare earth processors are primarily chemical companies, not mining or metallurgical companies, as the complexities of the processing procedures are' much more chemical in nature than metallurgical. The rare earths and the rare earth industry are normally divided into two groups - the ?light? or cerium group and the ?heavy? or yttrium group. They are so named because cerium and yttrium are the most common elements in 'heir respective groups and are so divided on the basis of mineralogical and chemical characteristics. The dividing line of the two groups is not rigidly fixed but usually is considered as being between samarium (atomic number 62) and europium (atomic number 63). Although the two groups are quite similar, processing procedures differ significantly, hence most processors tend to specialize in one group or the other. There is, however, a growing tendency toward participation in both groups.

Jan 1, 1960

By Yannis Faitakis, Brenda M. Wright, Gail Powley, Mark Hamblin, Randy B. Paine

A major problem in the ore extraction process is the high degree of variation in the mix of materials that make up the mined ore. The mix of materials makes it extremely difficult to characterize and predict the behavior of the ore when it is processed. The Quality Production Database (QPD) tool was successfully used in order to predict and transfer information regarding the quality characteristics of the ore being delivered to the extraction and hydrotransport unit operators. This paper describes the use of QPD in the prediction of various ore characteristics at the Syncrude Canada Ltd. processing facility.

Jan 1, 2000

By P. C. Kapur

The kinetics of green pelletization in a laboratory balling drum have been studied, using pulverized limestone as a model system. The growth characteristics of green pellets were found to be extremely sensitive to the moisture content of the material. Empirical kinetic equations, which incorporate a function of specific surface of the pellets as the criterion for growth potential, have been found to describe growth in a nucleation region and in a ball growth region. The rate constants in the kinetic equations are strongly dependent on the moisture content of the material being pelletized. Size distributions of the halls at different stages of pelletizing are also discussed.

Jan 1, 1965

By R. J. Zagrocki

Rekindled public concern about lead toxicity has intensified the awareness of lead-bearing materials in contact with the environment and the human population. Lead's common association with other metals makes the increasingly restrictive lead standards a primary concern for a large number of metal and metal-related industries. In commercial scale demonstration tests with lead-bearing wastes, the HRD Flame Reactor process has a demonstrated ability to separate and recover over 95% of the lead as a recyclable oxide, while rendering the remainder of the material as vitrified, non-leaching, and nonhazardous co-product. Recent Flame Reactor process tests and preliminary cost data for secondary lead soda slag are highlighted.

Jan 1, 1992

By W. C. Smith

Even with the most conservative mine plan, rib instability can occur unexpectedly, and if not adequately dealt with, can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation, sporadic zones of progressive rib instability were detected which culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Physical and computer models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1989

By E. R. Bauer

In response to the mandates in the MINER Act of 2006, the National Institute for Occupational Safety and Health (NIOSH) conducted refuge alternatives research that included characterizing the utility, practicality and survivability of refuge chambers and outby safe havens. NIOSH also prepared and delivered a report to Congress in late December 2007 that summarized the findings of the re-search, included recommendations concerning the design and performance specifications for refuge alternatives, and focused on specific information that could inform the regulatory process on refuge alternatives. This paper highlights NIOSH?s research and recommendations concerning refuge alternatives, survivability evaluations of refuge chambers and presents a brief review of the current deployment of refuge chambers in underground coal mines in the U.S. The research has lead to the conclusion that refuge alternatives have the potential for saving the lives of mine workers if they are part of a comprehensive escape and rescue plan and if appropriate training is provided.

Jan 1, 2009

By Dean Brox

The use of Tunnel Boring Machines (TBMs) for tunnel construction of long tunnels in the Andes of South America has been of mixed success in the past due to a variety of reasons and key lessons can be recognized. A review of past TBM tunnel projects in the Andes has unveiled some interesting findings for different TBM tunnel approaches with both world records of progress as well as nearly in-completed projects with machines being abandoned. Key considerations for the use of TBMs for tunnel construction in the Andes include geological issues; (faults, rock type, rock strength, rock abrasivity, durability, groundwater inflows),depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, intermediate access possibilities, minimum tunnel size, support requirements, contractor and labour experience, and project schedule demands. TBMs offer highly recognized schedule benefits(high progress, no concrete lining) for a project if intermediate access adits are limited as well as hydraulic benefits for water conveyance projects. Minimum specifications for TBMs can be easily developed to suit the unique requirements of any project so as long as all factors are carefully considered. The overall conditions and factors associated with some projects may suggest that it is not appropriate to use TBMs due to a perceived high risk. Finally, access for geotechnical investigations by drilling in the commonly steep terrain of the Andes is typically difficult and often not impossible. Alternative approaches for geotechnical investigations for TBM tunnels including comprehensive mapping, high-resolution airborne electric-magnetics for delineation of possible fault zones, and rock block sampling is presented and discussed.