Search Documents

By P. C. Thakur

In Part I of this paper, it was established that the width of longwall faces in highly gassy mines is primarily limited by the volume of air reaching the tail-end of the face. The ventilation air reaching the tail-end of the face should be not only enough to keep methane concentrations below the statutory limits (generally 1 percent) but also enough to prevent any gas layering. The air volume leaking from the longwall face into the gob should also be able to push the explosive methane-air mixture away from the gob area immediately behind the longwall face where active roof-fall is taking place (typically 30-45 m). The second group of variables that also controls the width of the longwall panel consists of (a) the rate of advance, (b) bleeder air quantities, (c) specific methane emissions for the gob area and, (d) efficiency and cost of gob gas capture. This paper will discuss the second group of variables and its impact on the optimum width of longwall faces in highly gassy coal mines.

Jan 1, 2009

By E. J. Karges

[For reasons well known to Mining Engineers, fine grinding in the wet form is quite universal inn plants engaged in the traction of metallic values from crude ore In the processing, of non-metallic and industrial minerals, however, fine grinding in dry form is the more common method. The crude materials generally contain less moisture than required for wet grinding, and the products are usually marketed or used in the dry form, most of them as powders. To grind wet would therefore entail the addition of water and the expense for drying the product, which is not justified. This paper will concentrate on the particle size reduction or fine grinding of materials to produce a dry powder]

Jan 1, 1963

By Julie Mitchell

The U.S. Bureau of Mines is conducting research on the application of expert sys tens technology to mining equipment diagnostics and predictive maintenance, to increase mining productivity and efficiency. One of the greatest hindrances to mining productivity is the breakdown of equipment, causing lengthy and costly delays. A diagnostic maintenance expert system (DIMES) is being developed for the hydraulic system of a continuous coal mining machine. Through the use of such a system, the frequency of equipment failures and repair time should be significantly reduced. This paper describes the application domain, the functional requirements, and the problem approach for DIMES, the design and implement at i on of the knowledge- based system, the sensor work involved with the project, and the future plans for the continued development of this and other expert systems.

Jan 1, 1989

By Joseph A. Dos Santos

"The subject of this writing was first published in 1998 with the emphasis on the hardware cost comparison. Other costs, such as the required land area and spatial volume, were mentioned but not emphasized, as these were not deemed as important for new projects where the space was appropriated as required. During the last decade, these other costs have proven to be more than equal in importance. These costs are emphasized here through specific accounts of actual highangle conveyor installations that demonstrate the importance and the high-angle advantage An update on the progress in sandwich belt highangleconveyor technology is also provided.Origin and progress in sandwich belt conveyorsCover belts of the 1950s. Large volume, highangle conveying by “conveyors with cover belt, dates back to the early 1950s, when such systems were employed at the bucket wheel excavator boom conveyor in German lignite mines to increase the depth of cut without increasing the boom length. Various systems were developed, patented and built. These systems were not a lasting success for various reasons, which are noted by Rasper[1]. In his 1958 “Review of Cover Belt Systems,” Rasper summarizes the characteristics which are worth pursing and those that should be abandoned. The former are akin to good conveyor engineering. The sandwich belt conveyor model. The first sandwich belt conveyor model allowed calculation of the required hugging pressure to develop the bulk material’s internal friction and preclude material slideback. A modern, accurate version of the sandwich belt conveyor model is presented in Fig. 1. This model depicts accurately a derating of the material cross-section allowing an ample belt edge distance that can tolerate normal belt misalignment without material spillage. The calculations must thus recognize that only part of the hugging pressure is imparted onto the material with the remainder transferred belt edge to belt edge affecting a material seal. Mathematical development of the sandwich belt model is covered by Dos Santos and Frizzell in their 1983 article, “Evolution of Sandwich Belt High Angle Conveyors.”"

Sep 1, 2016

By Bruce B. Redpath

Single-charge cratering tests can provide a direct measure of the powder factor necessary for achieving a desired effect in conventional blasting. If a desired blast effect, such as fragmentation or mound velocity, is produced by a single point-charge at a particular scaled depth of burial, then the cube of the reciprocal of that scaled depth is the appropriate powder factor for duplicating the effect in a conventional array of blast holes. Scaling formulas are presented that provide a link between point-, line- and plane-charge geometries, and which can be Apparent crater used for blast design. Mound and burden velocities from several sources are compared and several examples of blast design are given.

Jan 1, 1977

A virtual reality approach is presented that can aid entities such as mining companies and land use planners in communicating a visual understanding of a mining operation to interested stakeholders, citizens? groups, and public committees. These visualizations are particularly useful in permitting, production planning and mining closures, contributing to accurate communication and evaluation of mine plans, ultimate land use and evaluation of potential design options A case study is presented, that was created using commercially available virtual reality tools, to emphasize the benefits of visualization technologies in the sustainable development of mineral resources.

Jan 1, 2003

By Terry S. Maio

In 1978, Ozark Lead Company made the decision to expand the capacity of its mine/mill complex by 33%. The objectives of the expansion were to (a) increase mine' production capacity by 1816 tonne/d(2000 TPD), (b) increase lead metal pro¬duction by 21,790 tonne/y (24,000 TPY) and to (c) construct new facilities and/or modify exis¬ting equipment to accomodate the increased pro¬duction. The intent of this paper is to give a brief explanation of the equipment installed and the overall production and metallurgical benefits-realized from this expansion. The expansion was completed in the second half of 1980 with all equipment debugging and fine tuning completed by the first' quarter of 1981. The concentrator modifications and improvements were basically restricted to four areas: (1) materials handling, (2) automation: of the mill grinding circuit, (3) the increase of flotation capacity, and (4) concentrate dewatering.

Jan 1, 1983

By William E. Mead

The process of selecting a building site for a major structure is a complex procedure involving the consideration of a multitude of factors. The approximate geographic location for a structure is usually fixed by its intended function, though often there may be several site alternatives. Socio-economic, logistic, marketing and political factors are the primary site determinants. Also critical in site planning, however, are the environmental factors, both natural and man-made. These factors will influence the precise siting location within the limits allowed by the primary determinants and will dictate some of the basic design criteria. This paper discusses environmental factors, principally those which are natural conditions, that must be analyzed for five different groups of structures. The importance of thorough site environmental analysis based upon the principles of applied earth science is described. Significant elements to be considered in an appraisal of the geology, hydrology, seismology and meteorology are outlined.

Jan 1, 1968

By R. Du Plessis, J. D. Miller, D. G. Kotlyar

The low potential hydrophobic state of pyrite in amyl xanthate flotation with nitrogen is of particular interest with regard to the N2TEC flotation technology currently being used for the recovery of auriferous pyrite at Newmont’s Lone Tree Plant in Nevada. The N2TEC system had been found to operate satisfactorily, but cyanide in the flotation mill water appeared to be responsible for a loss in pyrite recovery. This supposition was confirmed with laboratory experiments and a program was initiated to study flotation chemistry variables by electrochemically controlled contact angle measurements. Experimental results show that activation of pyrite in such cyanide solutions can be achieved more effectively with lead than with copper. Subsequently, based on these fundamental studies, significant improvement at the Lone Tree Plant was achieved by lead activation, in which case the recovery increased to expected levels. The effect of activator is particularly significant not only with respect to pyrite depression by residual cyanide, but also with respect to collector (PAX) consumption and the initial state of the pyrite surface. Each of these issues is being studied in detail and research progress is discussed herein.

Jan 1, 2002

By Jozef Descour, Kazunori Nishioka, David M. Neil

Designers, engineers, and contractors are using three-dimensional seismic tomography for geotechnical site investigations and during tunnel excavation for hard rock and soft ground applications. Utilizing multiple types of seismic signals produced by a TBM, drill, or impact breaker, the reflection of different velocity features are processed into a holographic image of the actual structure to be encountered. The Mill Creek Phase 3 alignment in Cleveland, Ohio, was imaged to define existing conditions along a 1,200-ft section of a proposed 6.1-m (20-ft) diameter CSO tunnel and, specifically, a zone of expected anomalous conditions where drilling was inconclusive. In Japan, Kajima Corporation used TRT™ to image a number of tunnels including the Fujikawa and Kanaya tunnels in a combination of methods to map structural features along the alignment.

Jan 1, 2001

The next 13 years gave me an education that anyone, then or now, would well envy. W.T. Reid had founded Belmont School along the lines of Groton and, as at Groton, he sent many graduates to Harvard. He obtained excellent teachers and maintained as strict a discipline as the independent nature of the western students would stand. With a beautiful location in an unspoiled little valley in the foot- hills of the Coast Range there was every chance for walks and expeditions. The years at Belmont were good ones. My closest friends were Harold Jordan and Lewis Hackett. Lewis was son of the military director at the school. With half a dozen other very young inmates we early won the sobriquet of "The Dirty Dozen." Sliding down a steep muddy hill on barrel staves helped us earn the name. An inherited shyness exaggerated my sensitivity at being a "teacher's boy" and this prevented a close association with the wilder western boys who made up most of the schoolmates. Trapping wildcats and coyotes in the brush-covered hills and taking long walks gave me plenty to do. I had grown too fast and when I went to college was 6 ft 3 in. tall and weighed only 145 lb-hardly a respectable bean pole. I was only two months past 16 when I left for Harvard. The long summer vacations were happy ones. Most of them were spent in the high mountains, and even when I was ten years old I could keep up with anyone on long steep climbs. I learned to handle a rowboat during our stays at Lakeside, a rustic resort at the south- east corner of Lake Tahoe that could then be reached only by the steamer that made a dally trip around the Lake. Several of the teachers at Belmont remained good friends as long as we were on the same side of the continent. The finest was C.H. Rieber, who taught mathematics at Belmont for the first few years we

Jan 1, 1976

By K. P. Bingham

Lime is one of the largest volume chemicals produced in the United States. In 1979 approximately 21 million tons were produced. Lime is, in fact, second only to sulfuric acid as the largest volume basic chemical produced. Lime, also known as quick lime (calcium oxide) and hydrate lime (calcium hydroxide), is the principle alkali used in a multitude of industrial processes. In addition to its use as a principle industrial alkali, lime has experienced dramatic growth in four general market areas during the past 30 years. These four areas are: 1. Water Treatment - Lime is used extensively in treating and purifying water for industrial and potable use, Although significant tonnage is shipped to this market of municipal and industrial water treatment plants, the end-users are widely spread geographically and individual shipments are relatively low tonnage. Lime, which is nonhazardous, can safely be shipped by truck or rail to these small end-users. 2. Municipal and Industrial Waste Treatment - Environmental agencies at all government levels,

Jan 1, 1980

By J. G. Groppo

A beneficiation process has been developed to provide selective separation of unburned carbon from high LOI fly ash. Previous reports of utilizing froth flotation to achieve selective separations required long residence times and high reagent costs. A proprietary reagent system has been developed to address both of these limitations. Based on the results obtained from laboratory and pilot-scale investigations, a flowsheet design has been developed to produce two distinct usable products from class F fly ash; low LOI ash and a high carbon product suitable for reburning or further upgrading. A process flowsheet and description are presented.

Jan 1, 1996

By Tedd B. Bodimer

Why complicate an already complex machine such as a continuous miner by adding roof drills? Immediate permanent roof support is an immediate thought of the mining engineer just as elimination of frequent time-consuming places changes is a thought of the methods engineer. The realization of those two objectives has the potential for improved safety with increased production is the thought of the general manager. Miner-Bolters Used a Generation Ago These are not new thoughts as the 1CM continous miner equipped with two integral roof drills was introduced twenty-five years ago. Approximately two hundred of these machines were sold in the next five years for use in medium and high seam operations. The 1CM miner chassis that remained stationary in the center of an entry or room while the ripper bar was swung and sumped hydraulically provided an ideal platform for mounting two roof drills that could be operated during the continuous miner's production cycle. Two roof bolts could normally be installed in less time than required for the mining cycle. A typical roof drill unit is shown in Figure I.

Jan 1, 1981

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

By P. C. Thakur

Frictional ignitions (also called face ignitions) is defined as the rapid oxidation of a mixture of methane and air with a visible flame that could last from a few seconds to several minutes. These ignitions have a potential to turn into a mine explosion and eventually a large-scale mine fire. Over the last 22 years, U.S. coalmines have had 1566 frictional ignitions. There were no fatalities but serious injuries have occurred. Every effort, therefore, should be made to prevent frictional ignitions. The preventative measures fall under four categories: (a) degasification of coal seams prior to mining, (b) adequate ventilation, (c) wet cutting or water-jet assisted cutting and (d) machine design to minimize ignitions. The paper discusses each of these techniques in detail.

Jan 1, 2006

By Michael Fahey, Ravi M. Damodaran, Brij M. Moudgil

The flotation behavior of Florida phosphates was studied using statistical design of experiments to evaluate conditioning parameters and their effect on flotation performance. The solids loading, conditioning time and agitation speed during conditioning were identified as the important variables affecting the reagent coating onto particles. Flotation of the conditioned slurry was carried out at fixed collector dosage and flotation conditions. Phosphate recovery upon flotation was statistically modelled as a function of the conditioning variables. The results indicated that the conditioning variables had an interactive effect on the phosphate flotation performance. Statistical optimization revealed two conditioning regimes in which optimum flotation recovery was obtained. It was determined that optimal recovery can be obtained at lower conditioning energies.

Jan 1, 1995

By B. Farshadi, B. Asi, M. J. Habibian

"Dare-Zereshk deposit is one of the deposits supplies ore for Taft copper Complex in Iran Yazd province. This deposit is situated underneath a village the same name. Prior to mining activities, the village and its agricultural lands should be dislocated and deserted. This paper discusses about sustainability factors in this area including: Social and environmental effects of mining, dislocation and substitution of communities, created and lost jobs, financial and economic factors, quality of life index, infrastructures and post-mining land use. Studies have been performed by coupling Geographical Information System (GIS) with decision support tools such as Multi Attribute Decision Making (MADM), Through these studies revealed that considering the infrastructures developed for mine and plants, earned incomes and changing the community, mining activity in this area not only increases the social and regional sustainability but also improves it to a higher level."

Jan 1, 2011

By S. L. Bessinger

In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway's complex geometric cross-section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Headlosses in mine entries are calculated using Atkinson's Equation (1). [H = (English) H = (SI) (1)] where H = pressure ,loss, in. of H20 (Pa) K = friction factor, lbf min2/ft"4(Kg/m3) P = perimeter, ft. (m) L = airway length, ft (m) Q = airflow quantity, ft3/min (m3/sec) A = flow cross sectional area, ft2 (m2)

Jan 1, 1987

By V. D. Smar

The flotation process may be considered an interactive system consisting of many chemical, operational, and equipment variables. Changing anyone of these variables causes an overall system response change. This study examines the effects of simultaneously changing the operating variables of: (1) frother concentration and air flow rate, and (2) frother concentration and collector concentration. It is part of a comprehensive study to look at how changes in several of the major variables may be used to produce interactions which will allow the rougher flotation process to be optimized. Ultimate recovery, flotation rate, concentrate grade and froth quality, are used as the major evaluative criteria.

Jan 1, 1993