Search Documents

By J. Kemeny, K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in an area of the mine that contains argillite and is relatively homogeneous. This process also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for argillite will be updated as more tests are conducted, and the model will be extended to the four other primary rock types at the Asarco Mission mine.

Jan 1, 2011

By T. W. Beck, J. A. Organiscak

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling dust and gas. Redirecting all the air toward the face equally up both sides of the machine increased the dust and gas concentrations around the machine. When all of the air was redirected toward the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face, at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all of the scrubber exhaust was redirected toward the face either up the off-tubing side or equally up both sides of the mining machine.

Jan 1, 2013

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2017

By Yi Luo

Subsidence events occurring above inactive room-and-pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence, because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidence to identify the cause is often lacking. In order to conduct a complete and impartial investigation, thorough knowledge of subsidence theories and other ground control topics, as well as broad experience, are required.

Jan 1, 2011

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2017

By R. Brown, A. J. S. Spearing, M. Treinen, M. Theisinger

The mining and use of coal creates a significant amount of waste material that needs to be safely disposed of. It is likely that in the medium term, the Environmental Protection Agency (EPA) in the U.S. will categorize all such products as a new category – special waste. This would make the materials subject to many of the requirements for handling toxic waste, which will complicate the disposal of such products and significantly increase the disposal costs. Underground disposal would, therefore, seem to be the obvious solution, especially if the placed material can have low or no permeability, so that water table pollution does not present a serious long-term issue after placement. Significant additional advantages could be derived from this backfilling, including the reduction or elimination of surface subsidence, increased extraction, reduced surface waste disposal footprint and the elimination of explosion-proof seals in worked out areas. The research using a specific coal waste product as a typical example proved that the method of placing the backfill at a high density with low permeability is technically viable, but it must be made more cost effective and the other potential benefits quantified and costed in order to present a true comparison.

Jan 1, 2010

By A. G. Mayton, D. H. Ambrose, C. C. Jobes, N. K. Kittusamy

In a systematic study, the National Institute for Occupational Safety and Health (NIOSH) evaluated seat designs in low- and mid-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. The purpose was to support, with additional data, earlier findings that NIOSH ergonomic seat designs (featuring viscoelastic foam padding and lower-back support) may help reduce health risks to operators of coal mine shuttle cars. Eight shuttle car operators evaluated seven seat designs (one already in use in each vehicle and five NIOSH designs) relative to perceived and measured whole-body vibration (WBV) exposure (including vehicle jarring/jolting) and discomfort. Operators’ perceptions using a visual analog scale (VAS) and questionnaire ratings were compared with International Standards Organization (ISO) 2631-1:1985 fatigue-decreased proficiency (FDP) limits and measured WBV levels on low- and mid-seam shuttle cars. Objective and subjective data results indicated that NIOSH seat designs (with added adjustability, lower-back support and improved seat padding) performed better to reduce vehicle jarring/jolting levels and that shuttle car operators favored them over existing seat designs. The NIOSH low- and mid-seam shuttle car seats showed 45 to 77 percent better performance in FDP and 9 to 60 percent better performance overall in operators’ ratings. Considering the VAS results for low- and mid-seam shuttle cars under no-load conditions, operators rated the level of jarring/jolting 18 to 89 percent lower with the NIOSH seats. Reductions in measured vehicle jarring/jolting were 19 to 46 percent for the three-directional vector sum accelerations relative to the existing seats on the low- and mid-seam shuttle cars. Questionnaire responses indicated that operators for both shuttle car models rated NIOSH seat designs as more comfortable overall. Vehicle operators most frequently suggested adding armrests to improve the seats on the mid-seam shuttle car. A suggested improvement for the low-seam shuttle car was to make the seat a better fit for the operator compartment, which would enhance clearance between the operator and vehicle controls and allow for better seat adjustment and operator visibility.

Jan 1, 2009

By M. Heger, V. Lund, P. Mongeon, D. Bogunovic, V. Kecojevic

The U.S. coal mining industry consumes a significant amount of energy, primarily diesel fuel and electricity. The continuous global increase in energy demand, high energy prices and environmental issues related to carbon dioxide emission represent a substantial challenge for the mining industry. This paper presents the result of research on development of an integrated data environment system for analysis of energy consumption in a surface coal mine. A case study on an operating surface coal mine is carried out to demonstrate the practical application of the developed system. The research work presented here may be used by mining professionals to help provide the answers to the crucial questions of when, where and how much energy is being used. This developed system represents a framework for efficient management of energy consumption.

Jan 1, 2009

By G. Bylapudi, A. Spearing, J. Weber, K. Mondal

U.S. National Institute for Occupational Safety and Health (NIOSH) reports state that about 100 million rock anchors are installed annually in U.S. coal mines (Tadolini et al., 2006), and rock-related safety remains an issue. The majority of these coal mines have conditions that make corrosion probable in the longer term. Despite this, very little research has been performed to analyze corrosion and its effects on rock anchors in coal mines. To further evaluate the effects of corrosive conditions in coal mines on rock anchors, three different experiments were conducted during an initial Illinois Clean Coal Institute (ICCI)-funded project from 2008-2009. The results of these experiments were further studied, with additional tests, in the extended ICCI-funded project during 2011-2012. The experiments were destructive testing, electrochemical testing (potentiodynamic polarization tests) and open circuit potential (OCP) testing, conducted in order to study corrosion in environments similar to those found in Illinois coal mines with a focus on major rock anchor types typically installed underground. Destructive test results showed highest reduction in peak strength at higher pH and temperature. From the destructive test results, epoxy-coated and galvanized anchors were observed to be better when compared to uncoated. Electrochemical testing was performed to find the corrosion potential and corrosion rates of ASTM A615 steel grades 40, 60 and 75 in four different solutions of varying sulfur content at ambient temperature. The effect of temperature and pH levels on corrosion potential and corrosion rates of steel grades were also evaluated with additional electrochemical testing, where an increase in temperature with all other constant conditions caused a significant increase in the corrosion penetration rate. OCP data indicated higher corrosion potential values (-mV) for rock anchors in wet areas, when compared to those from the dry areas. OCP test results of the rock anchors from the laboratory corrosion chambers were similar to those measured in the sampled coal mines.

Jan 1, 2013

By K. A. Perry, R. Q. Eades

The University of Kentucky conducted inerting tests and angle of ejection tests on three types of rock dust. A newly developed hydrophobic dust was compared against typical dry and wet dust applications. This new product is designed to alleviate respirable dust concerns for dry dusting and caking issues with wet dusting. Samples for both test types were prepared in a laboratory and subjected to temperature and humidity cycles that are typical of an underground coal mine. Inerting tests were conducted in a 38-L chamber with a 5-kJ Sobbe igniter. Angle of ejection testing was conducted at the University of Kentucky Explosives Research Team’s laboratory in Georgetown, KY. The results of these tests indicate that the newly developed dust has improved results for flame suppression and ejection compared with typical wet dust applications. The significance of these results is discussed with regard to existing respirable dust regulations and the issues associated with caking.

Jan 1, 2016

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2017

By Y. Luo

Highwall mining, which is a relatively new mining method, is a preferred and often the only feasible method for extracting coal reserve left by surface mining operations in areas with steep terrain and in closely spaced thin coal seams. Though its safety record is comparable to that of surface mining, failures of mine structures in highwall mines, especially the highwall, have occurred. Methods for the systematic designing of highwall mines to meet the safety and operational challenges are still evolving. This paper presents the results of research into improving the existing design methods and developing new ones for highwall mining operations. The design methodology is aimed at ensuring structural stability of the highwall, roof, web and barrier pillars and preventing subsidence. It takes into consideration the major ground control challenges of soft and layered mine roofs, and interactions from mining closely spaced coal seams. An optimization design process applying a pressure arch concept can be incorporated to improve the recovery rate of coal reserve. A computer program based on the design methodology was developed.

Jan 1, 2015

By L. Zhou, A. Martikainen, G. Goodman

Continuous airflow monitoring can improve the safety of the underground work force by ensuring the uninterrupted and controlled distribution of mine ventilation to all working areas. Air velocity measurements vary significantly and can change rapidly depending on the exact measurement location and, in particular, due to the presence of obstructions in the air stream. Air velocity must be measured at locations away from obstructions to avoid the vortices and eddies that can produce inaccurate readings. Further, an uninterrupted measurement path cannot always be guaranteed when using continuous airflow monitors due to the presence of nearby equipment, personnel, roof falls and rib rolls. Effective use of these devices requires selection of a minimum distance from an obstacle, such that an air velocity measurement can be made but not affected by the presence of that obstacle. This paper investigates the impacts of an obstruction on the behavior of downstream airflow using a numerical CFD model calibrated with experimental test results from underground testing. Factors including entry size, obstruction size and the inlet or incident velocity are examined for their effects on the distributions of airflow around an obstruction. A relationship is developed between the minimum measurement distance and the hydraulic diameters of the entry and the obstruction. A final analysis considers the impacts of continuous monitor location on the accuracy of velocity measurements and on the application of minimum measurement distance guidelines.

Jan 1, 2012

By A. Lashgari, V. Kecojevic

This paper presents research on the environmental impact of digging and loading equipment used in surface coal mining. Environmental impact was assessed through the measurement of equipment exhaust and dust emissions, and sound level. In this study, exhaust emission refers to carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur oxides (SOx) and volatile organic compounds (VOCs). Dust generation refers to fine particles (PM2.5), inhalable particles (PM10) and total suspended particulate matter (TSP). Sound level refers to the sound pressure level at different distances from the equipment. Modeling of the environmental impact of digging and loading equipment was conducted using the Microsoft Visual Studio.NET software package. This research was a part of a broader project involving the development of a software system for the selection of productive, cost-efficient and ecofriendly mining systems, sponsored by the Appalachian Research Initiatives for Environmental Sciences (ARIES). This research may assist mining professionals in quantifying the environmental impact of digging and loading equipment, and developing strategies for reducing the overall impact of such equipment in surface mining.

Jan 1, 2013

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By L. Martin, M. Raffaldi, M. Stepan, D. Benton

The Office of Mine Safety and Health Research, Spokane Mining Research Division, is continuing its high-energy, high-displacement testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link mesh, welded-wire mesh and combinations of them. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can assist in interpreting the condition of installed surface support. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to better quantify the stability of installed shotcrete support.

Jan 1, 2016

By Guy Reed, Russell Frith

In situ or pre-mining horizontal stresses are arguably the least well understood of the principal inputs into underground coal mining geotechnical engineering design, whether analytical, empirical, or numerical. This is a direct result of both the cost and difficulty of obtaining meaningful stress measurements, the various limitations of the measurement method in terms of sourcing strata types that approximate the assumed conditions of the post-measurement mathematics to convert measured strains into stresses, and a common practice by some geotechnical professionals to preferentially utilise generic values rather than interrogate the available measurement data for cause and effect relationships between horizontal stress magnitudes, directions and a range of associated controls. That numerical modelling simulations attempt to mimic reality but often rely on simplified generic horizontal stress input assumptions is a particular cause for further consideratio The paper attempts to further explore the nature of in situ horizontal stresses using a range of stress measurement results from the Australian coal sector supplemented by several international studies addressing the same basic issue, the result being a number of credible and highly relevant “cause and effect" inter-relationships between the three principal in situ stresses in addition to the influence of rock properties (e. Young's Modulus and Poisson's Ratio), cover depth and the larger-scale structural geological environment. In particular, the paper demonstrates that despite being commonly overlooked as a primary rock/coal material property, Poisson's Ratio and the associated K Effect are intrinsic to understanding 3D in situ stress measurement results and therefore, predicting in situ stress magni- tudes more generally for geotechnical analyses purposes. As a fundamental question, the paper addresses whether it is necessary and of engineering value to characterise in situ horizontal stresses: according to distinct "domains," in the same way that more easily identifiable geotechnical properties such as rock mass ratings, coal seam thickness, ply splits, and cover depth are often treated.

Jun 25, 2024

By Scott Burchmore, Jason Emery, Michael Melville

This paper presents best practice data management for monitoring of extensometers in Australian underground coal mines. This work is based on the combined experience of the authors and the available literature. The information and ideas presented herein are a culmination of many years of database development founded from mine site-based ground support design, underground inspections, extensometer data management and data analysis. Each author has more than ten years’ experience as a practicing geotechnical engineer at several operating industry wide research project focused on utilizing mechanical extensometer data for data analytics and machine learning. Principal hazard ground control management plans, stipulated in Australian coal mining legislation, outline the mandatory installation of ground monitoring devices during routine mining activities. After 20+ years of data gathering the barrier to implementing modern data analytics remains the challenges imposed by inconsistent data structure and data quality. This inconsistency is still routinely found between sites, companies and mining regions. Through the relatively simple application of a standardized database structure, the potential to shift from simplistic tracking of trigger levels, siloed at individual sites, to an industry standard method for compilation & comparison of monitoring data is enabled.

Jun 25, 2024

By Jiachen Wang, Nan Wang, Yang Li

The energy structure and consumption ratio in China determine the practical demand for the collaborative mining of coal and co-associated resources. The multi-layer mining of coal, uranium, coalbed methane, and oil and gas co-associated resources, represented by the Ordos Basin, Junggar Basin, and Tarim Basin, faces numerous challenges. Additionally, coal has been found to coexist with various mineral resources in 33 coal-bearing basins worldwide. The scientific issues related to the multi-layer development of coal related co-associated resources urgently need to be addressed. This paper discusses the unique challenges and potential solutions in the multi-layer development of coal-related co-associated resources. The challenges include large extraction space, high mining intensity, intense overburden movement, rapid surface subsidence, and severe overburden damage due to repeated mining disturbances. Proposed solutions include the establishment of a correlation mechanism between multi-layer mining and the carrying capacity of the overburden environment, analysis of the impact characteristics of multiple field couplings, and exploration of their superposition evolution laws. The paper also proposes the development of a comprehensive evaluation and prediction system for overburden environmental capacity loss, a global sensitivity analysis model for overburden environmental capacity, and an intelligent identification and early warning system based on multi-source information fusion. These solutions aim to achieve scientific and precise mining with minimal overburden environmental capacity loss. And the multi-layer development of coal-related co-associated resources is a complex task that requires a multidisciplinary approach and innovative solutions, and further research is needed to validate these strategies and explore new methods and technologies for efficient and sustainable extraction.

Jun 25, 2024

By Peter Zhang, Daniel Su, Berk Tulu, Bo Hyun Kim, Zoheir Khademian

Over 2,000 shale gas wells have been drilled in the Pittsburgh Seam longwall reserves. As longwall panels are laid out, some of these shale gas wells must be located in longwall chain pillars. With longwall mining on both sides and the constraint of chain pillar size, gas well in chain pillars are subjected to longwall-induced ground movements and stresses, which could induce deformations in gas well casings Casing deformations are associated with several factors such as overburden geology, surface topography, setback distance, and casing construction. Overburden geology is one important factor that largely determines the locations and levels of deformations in gas well casings Previous NIOSH gas well research has found that casing deformations above the coal seam horizon are smaller under deep cover than unde shallow cover and that casing deformations could occur at the coal seam horizon under deep cover. Recent mine-by cases have provided more insights into the locations and amount of longwall-induced casing deformations as well as the potential occurrence of a large casing deformation at the coal seam horizon. This paper presents three recent mine-by cases with shale gas wells in the chain pillars between two adjacent longwall panels under different overburden depths. Casing deformations were measured by multi-finger caliper surveys and predicted with numerical modeling. With the established numerical model, the effect of overburden depth was further analyzed to investigate the potential occurrence of a large casing deformation at the coal seam horizon under deep cover. These mine-by cases not only provide a general demonstration of how overburden depths can affect longwall-induced stresses and deformations but also give a good indication about the level of casing deformations that could occur under different overburden depths. The study concludes that (1) casing deformations reduce with increase of overburden depths at the gas well; (2) a cementing alternative with production casing uncemented is an effective means to eliminate production casing deformations; and (3) large plastic casing deformation could occur in the production casing at the coat seam horizon under deep cover. The experience and knowledge gained from these mine-by cases would help longwall operators and gaza companies to take appropriate measures to minimize the influence of longwall mining in shale gas wells in chain pillars.

Jun 25, 2024