Search Documents

By CORA ROELOFS

In the USA, miners are at higher risk for work-related disorders that could precipitate an opioid prescription, injury-related opioid prescriptions, and opioid overdose. We aimed to support prevention of these outcomes with an “opioid hazard awareness” miner safety training module. In January and February 2020, the training module was embedded within required mining safety and health training for stone, sand, and gravel miners in Massachusetts (USA). Training impact and reception were assessed with a pre- and post-training survey of trainee characteristics, training content knowledge, and attitudes. Over 800 miners were trained and over 600 responded to surveys. We found statistically significant improvements in opioid risk factor knowledge and knowledge of resources to help a coworker. Nonstigmatizing attitudes were high both at baseline and following the training. The training was perceived as relevant and useful by trainees. Improving opioid hazard awareness in high-risk worker populations has potential to reduce opioid dependence and downstream impacts including overdose death. Employer injury-prevention efforts should be reinforced while worker health and safety training enhances awareness of opioid-related harms and prevention strategies for miners and other high-risk worker populations.

Nov 19, 2021

By Atta Ur Rehman, Kwame Awuah‑Offei

This paper examines the effect of bucket geometry (cutting blade profile, floor profile, and blade thickness), speed, motor power output, and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scaled model of a load-haul-dump in full factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated to penetration and draft; muckpile particle size is positively correlated to penetration and negatively correlated to draft (p < 0.0014). The results show that buckets with a semi-spade cutting nose profile yield the highest penetration (mean 118.30 mm) followed by those with the spade (mean 108.88 mm), which also yield higher penetration than those straight blades (mean 95.19 mm). Bucket floor profile and blade thickness had no significant effect on penetration or draft. Also, we determined that increasing the speed and motor power output, simultaneously, can reduce bucket penetration. Thus, operators should not waste energy for no additional gain or even loss in bucket penetration. Also, the work finds speed and motor power output each combine with muckpile particle sizes to affect bucket penetration. This research furthers our understanding of the effectiveness of different bucket geometries in improving penetration and reducing draft for rubber tire loaders.

Oct 29, 2021

By MUSTAFA ERKAYAOGLU, ENVER YILMAZ

Coal is still a part of energy generation worldwide and has a significant role in the sustainable development of countries. The amount of shallow coal deposits is getting scarce, making efficient underground mining operations crucial for both local and global economies. In underground mining operations, longwall mining is a commonly utilized method to extract deep coal deposits. One of the leading engineering goals in longwall mining is increasing the efficiency of the system by investigating the effects of operational factors on equipment. This paper investigates the shearer performance for a longwall top coal caving operation by discrete event simulation that includes modeling the double-drum shearer, belt conveyors, stage loader, and armored face conveyors (AFC) to evaluate system performance by considering the amount of daily coal production of the shearer. As a result, the most influential factor on mine production is determined and a data-based framework is developed. This study suggests a framework for data collection, data analysis, and the interpretation of the operational data to evaluate the primary production unit’s performance. The models developed for the face coal extraction operations in a longwall top coal caving (LTCC) mine have a bi-directional cutting system and can be implemented in other operations readily.

Jul 2, 2021

By Yuexin Han, Yanjun Li, Peng Gao, Yongsheng Sun, Qiang Zhang

The non-isothermal magnetization roasting process and isothermal magnetization roasting process of siderite ore were investigated using thermogravimetric (TG) analysis and a real-time infrared gas analyzer. X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) were used to analyze the characteristics of samples. The results showed that the decomposition degree and decomposition rate of siderite ore were vitally affected by heating rate and roasting temperature. It was determined that A1 reaction model (f(α) = 1 − α) and A3/2 reaction model (f(α) = (3/2)(1 − α)[−ln(1 − α)]1/2) were the most probable mechanism function of the non-isothermal decomposition process and isothermal decomposition process, respectively. The phase transformation and decomposition mechanism during the roasting process were evaluated. Siderite decomposed in the process of magnetization roasting, released CO and CO2, and transformed into strongly magnetic magnetite. The SEM images highlighted that as the decomposition progressed, the structure of roasted samples was destroyed, and an increasing number of cracks and pores emerged on the surface, which is advantageous to the following grinding process.

Mar 26, 2021

By Shannon Seitz, Qingwen Shi, Junfeng Pan, Shuwen Wang, Brijes Mishra, Shaohong Liu

Delayed coal bursts in deep coal mines have caused significant fatalities and economic losses in recent years. Instead of occurring right around the advancing face, this particular type of coal burst is characterized by its occurrence at a certain distance behind the advancing face. To better understand the mechanism of a delayed coal burst, we used borehole camera, electromagnetic CT, and borehole deformation monitoring device to observe the fracturing and deformation process of an advancing entry’s surrounding coal in the field. Borehole camera detection showed a zonal disintegration phenomenon in the advancing entry’s surrounding coal. Electromagnetic CT detection showed that zonal disintegration developed within 14 days of excavation. Borehole deformation monitoring indicated a deformation rate difference between the intact zone and fractured zones. The deformation rate difference was observed to increase with time and cause increasing elastic energy accumulation in the intact zone. The cumulative elastic energy in the intact zone finally caused a delayed coal burst in the entry. Sensitivity analysis of the cumulative elastic energy was conducted based on a thick-walled model deduced from field detection. The model shows that the smaller thickness of the intact zone brings higher elastic energy in the intact zone. This investigation provides an improved understanding of delayed coal bursts in deep coal mines.

Oct 19, 2021

By Barbara J. Arnold

Combat Infantrymen’s Badge and Bronze Star Medal. Following his discharge from the Army, he re-entered SDSM&T in 1946 and earned a B.S. degree in Metallurgical Engineering in 1948. He then received an M.S. from Montana Tech (MT), worked several years in industry and then as an Assistant Professor at the University of Washington (Seattle). He joined his Montana Tech colleague, Douglas W. Fuerstenau, at The Massachusetts Institute of Technology (MIT), receiving his doctorate in 1957. While at MIT, he married Clare M. Donaghue of Dorchester, Massachusetts, in 1955

Jan 3, 2022

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and point cloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion point clouds with millimetric precision, capturing the structure of the rock mass. The automated point cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors such as site specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using discontinuity set extractor (DSE). Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time. The analysis determined that the automated mapping algorithm was able to identify the same discontinuity sets that had been manually mapped. The automated mapping software mapped an excessive amount of smaller fractures, which caused the comparison of both mapping techniques to be unsuccessful in terms of trace length and spacing.

Mar 19, 2021

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the disasters occurring in underground coal mines. As a typical case, the spontaneous combustion of broken coal left in the longwall gobs often happen which could greatly interrupt the normal mining production. Such concealed thermal event is featured as rapid development and difficulty in locating “hot” spots. If such spontaneous combustion fails to be timely prevented and controlled, a large amount of toxic gases (mainly CO) and smoke could flow and diffuse in the underground working sections, which could present safety hazards for coal miners. In this paper, based on an coal spontaneous combustion event happened in a Chinese gassy mine, the fire ratios derived from the gas composition data obtained through the tube bundle mine atmospheric monitoring system are used in determining the fire status. A comprehensive and collaborative fire extinguishing effort including inert gas injection, underground pressure balance, and sealing enhancement are made to control the fire progress. Simultaneously, the effects of such works to control the spontaneous combustion event have also been quantified using the fire ratios to justify again. Finally, the danger of coal spontaneous combustion in gob is eliminated, and the longwall panel is successfully re-opened for normal production.

May 6, 2021

By Dong Yang, Jicai Han, Xiaoshuang Guo, Tichang Sun, Zhengyao Li

Straw charcoal was used as a novel reductant in the co-reduction roasting of laterite ore and red mud. The influence of the reductant dosages, co-reduction temperature, and co-reduction time were investigated. Results showed that a powdered ferronickel product of 1.81wt.% nickel and 81.40wt.% iron was obtained under straw charcoal dosage of 15wt.% and roasted at 1250 °C for 80 min. The corresponding recovery of nickel and total iron were 97.21wt.% and 98.87wt.%, respectively. The performance of straw charcoal was also compared to that by the conventional coke reductant. Results showed that ferronickel particles using straw charcoal were larger in size than coke, mainly due to the lower S (0.14wt.%) and ash content (3.80wt.%), which could not hinder the agglomeration of the ferronickel grains, and lower melting point that producing liquid phase and promoting ferronickel particles growth. In addition, the gasification reactivity of straw charcoal is better than that of coke, which is beneficial to the iron oxide reduction and the recovery of iron. To conclude, straw charcoal is a promising reductant for the co-reduction of laterite ore and red mud in coal-deficient areas.

Aug 12, 2021

By Inoka E. Perera, Michael J. Sapko, Marcia L. Harris

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effectively inert a coal dust explosion, rock dust must be able to disperse as individual particles to air. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anticaking additives after being exposed tomoisture and then dried. The dusts were exposed tomoisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anti-caking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Experimental Mine (LLEM), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for 1 day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for 6 months. This report details the analysis and characterization of anticaking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber.

Apr 12, 2021

By C. RAMADINI, F. NURJAMAN, A. SHOFI, B. SUHARNO

In this work, the selective reduction of lateritic nickel ore was carried out using sodium sulfate, sodium carbonate, and sodium chloride as additives. The 5 wt% of anthracite coal, which contains 60.35% of fixed carbon and 1.9% of sulfur, was used as a reductant. All raw materials were mixed homogenously prior to the pelletization process into 10–15 mm of diameter. The reduction process was carried out to 50 g of pellets at 950 °C, 1050 °C, and 1150 °C for 60 min in a muffle furnace at atmospheric pressure. It continued with a wet magnetic separation process to separate ferronickel (concentrates) and impurities (tailings). Iron and nickel grade analysis was performed using XRF, while phase transformation and microstructure were analyzed with XRD and SEM–EDS. The results showed that the sodium sulfate was superior, resulting in the highest nickel grade in concentrate, i.e., 15.06%. The sulfidation mechanism, which could inhibit the metallization of iron, effectively increased the nickel grade in concentrate than decomposition of carbonate and chloridization process. The sulfur content in the reductant also influenced the selective reduction process. It promotes more sulfidation of iron, thus increasing the nickel grade in concentrate.

Jul 7, 2021

By Shahab Alizadeh, Ahmad Khodadadi Darban, Mehdi Mohseni, Mahmoud Abdollahy

This study probed the selective separation of lanthanum and yttrium in a nitrate medium in the presence of aluminum and calcium impurities using di-(2-ethylhexyl) phosphoric acid (D2EHPA). The factors studied in a central composite design (CCD) included extractant concentration, pH, concentration ratio of total impurities to rare earth elements, and interaction of these three factors. The extraction mechanism and types of extracted metal-containing species were delineated by the slope analysis method. The obtained thermodynamic data showed that lanthanum and yttrium extraction by the D2EHPA extractant was exothermic. The extraction of both rare earth elements was accompanied by an entropy reduction. The negative magnitude of ΔS in yttrium extraction reaction suggests stronger D2EHPA-Y(III) complexation relative to La(III). As entropy decreased and enthalpy increased, the extraction process became unspontaneous. Using the proposed flowsheet, lanthanum and yttrium products with > 90% purity were obtained.

Aug 10, 2021

By LUIS ALBERTO TORRES-CRUZ

The assessment of liquefaction vulnerability is crucial to understanding the potential consequences of a tailings dam failure. The “Plewes method” is a relatively well-known and simple screening method to assess liquefaction potential based on results of cone penetration testing (CPT) which may be complemented with laboratory testing. The objective of the current work is to emphasise the screening nature of the method and its uncertainties when applied in tailings deposits. Specifically, the paper highlights the difficulties in assessing the intrinsic uncertainty of the method and the additional uncertainty that results from variations of the slope of the critical state line (λ10) along the depth of the CPT sounding. The results of the method are too uncertain for detailed characterisation of tailings even when a relatively low intrinsic uncertainty is assumed. However, the method characterises weaker soils with lower uncertainty (although still too high for detailed characterisation) than stronger soils. The uncertainty of the method is negatively affected by the relatively low λ10 values that are typical of nonplastic tailings. It is suggested that the results of the method should be presented in scatter plots in which the spread of the data is consistent with the uncertainty of the method.

Jan 28, 2021

By CHENCHEN SUN, GUOPING LUO, GUOCHENG ZHANG

Preparation of briquettes by adding CaF2 reagent into the Australian iron ore powder. The structure and morphology of iron ore briquettes during various reduction stages (i.e., Fe2O3→Fe3O4, Fe3O4→FeO, and FeO→Fe) were observed via an ore microscope and scanning electron microscopy. The results showed that CaF2 reacted with SiO2 to form CaO and SiF4 gas during the roasting process. The reduction swelling index decreased from 12.36 to 8.83% when the CaF2 content in the briquettes increased due to CaF2-mediated refinement of the hematite grains during the first stage of the reduction process. Lattice distortion resulting from the presence of Ca2+ in the FeO lattice during the second stage of the reduction process, coupled with an increase in the porosity of the iron ore briquettes and the formation of a low-melting-point slag phase, promoted the anisotropic growth of FeO lamellar crystals, which resulted in an increase in the reduction swelling index from 4.27 to 7.36%. During the third stage of the reduction process, the growth of iron whiskers was promoted by wüstite (FeO) lattice distortion caused by a solid solution of Ca2+ in the FeO lattice; the reduction swelling index increased from 15.61 to 24.72%, resulting in the catastrophic swelling of the iron ore briquettes.

May 27, 2021

By Eugie Kabwe

The increase in depth of mines due to the depletion of surface deposits leads to unsafe tunnel construction and overall ore extraction. This is due to tunnel instability associated with the surrounding rock mass’s ability to exhibit creep that occurs over time. However, the explicit description of this mechanism using conventional constitutive models has proven to be difficult and inadequate. Hence, this paper presents an integrated viscoelastic viscoplastic visco-damage model with the Duvaut-Lions function. The presented model is calibrated by experimental data to determine the viscoelastic viscoplastic and visco-damage parameters. It is further implemented in a finite volume numerical code and verified on an experimental scale by numerical modeling of a cylindrical specimen. It describes the 3-phase creep mechanism perfectly as compared to the inbuilt conventional integer-order derivative model. Results from the conducted verification show that it can successfully be employed to describe the long-term behavior associated with the creep mechanism.

May 16, 2021

By Xiaobo Zhang, Panshi Xie, Xiaobo Wu, Ding Lang, Jiandong Yu, Yongping Wu, Kun Feng

In a fully mechanized top coal caving mining process, the mechanical properties of the top coal deteriorate constantly, and the stability of the support is determined by the boundary position of the top coal entering the limit equilibrium state. Top coal flaking occurs more easily along the advancing direction owing to an increase in the distance of the boundary from the wall. Moreover, the strength of the coal seam is an important factor that determines the boundary position. The equation of the top coal limit equilibrium zone boundary, used in fully mechanized top coal caving mining, was determined based on the limit equilibrium theory, continuum damage mechanics, and the Hoek–Brown rock empirical strength criterion. Using the RFPA3D and UDEC numerical analysis methods, the effect of top coal strength on the mechanical behavior during the mining process was determined; and the space–time relationship between the top coal deformation failure, damage evolution, and boundary of the limit equilibrium zone was established. The results revealed that when the coal mass entered the limit equilibrium zone, accelerated crack development, accelerated damage, and axial unloading occurred. Moreover, an increase in the coal seam strength caused the boundary of the top coal limit equilibrium zone to be closer to the wall. By comparing the numerical results with the theoretical results, the overall trend was found to be consistent, allowing the verification of the rationality and reliability of the determination equation of the boundary position of the limit equilibrium zone.

Sep 21, 2021

By Lee R. Kump, Sarma V. Pisupati, Peter L. Rozelle, Alan R. Larson, Timothy S. White, Nicholas A. Crescenzo, Maureen D. Feineman

The Mercer Clay bed in central Pennsylvania has produced feedstocks for the refractory industry in the USA and has also been investigated as a source of alumina and lithium. Developments in global markets for these commodities, as well as rare earth elements, have led to their classification as critical minerals in the USA, in turn renewing production opportunities for the Mercer Clay resource. The work reported here includes a review of the clay types and minerals involved, as well as past mineral processing and extractive metallurgy test work, and reports new research results from renewed investigation of the deposit as a polymetallic resource. This renewed work has found lithium contents that exceed 1,000 ppm, lying directly below the overlying Mercer coal, where the alumina content ranged from 32 to 34 wt%. Total rare earth concentrations were somewhat lower than have been found elsewhere in the region, and the highest contents were also found to be stratigraphically close to the coal. Further work is required to establish the mineral hosts for lithium and rare earths and to define the extent of enriched alumina, lithium, and rare earth concentrations.

Jul 22, 2021

By Rosa Malena Fernandes Lima, Kerollan da Silva Ramos, Joyce de Assis Silva, Geriane Macedo Rocha

This study evaluated the effects of collector type amide-amine compared with those of conventional etheramine acetate (both cationic collectors) on the surface properties of quartz and hematite. An examination of certain properties of the reagents indicated that the new collector amide-amine has CMC (critical micelle concentration) and pKa values (100 mg/L and 8.2, respectively) significantly lower than those of etheramine (800 mg/L and 9.4, respectively). Microflotation tests showed that the recoveries of quartz with amide-amine in all the concentrations tested were higher than those with etheramine. This is attributed to its lower CMC and pKa values. The selectivity window between quartz and hematite flotation using amideamine was higher at pH 10.5 (approximately 80% for 5 mg/L). Therefore, the use of starch is not necessary in siliceous itabirite flotation by amide–amine collector. Zeta potential measurements and infrared spectra reveal that the adsorption of amide-amine collector on quartz surface occurs mainly by electrostatic attraction. Considering the better collectability of amide-amine for quartz flotation and lower adsorption affinity for hematite surface than etheramine, the amide-amine is a promising collector to be used in reversal iron ore flotation.

Jul 30, 2021

By BHAMIDIPATI S. SASTRY, Pavan Kumar Kattamuri, ADITYA PANDEY

The thermal conductivity of rock surrounding the airway is one of the most important thermal properties for estimating strata heat transfer into the mine air and for designing the air-cooling strategies. Several laboratory methods are available for the determination of thermal conductivity; however, most of them are complex and cumbersome. The present study explains the working principle of Lee’s apparatus which is relatively simple, easy to fabricate and use, and provides consistent results. In the present study, thermal conductivities of sandstone cores obtained from an Indian coal mine are determined using Lee’s apparatus. An approach is discussed for determining the temperature gradient of sandstone specimens while cooling and used for calculating thermal conductivity. The thermal conductivity of different sandstone specimens attains values between 2.37 and 2.59 W m− 1 °C−1. For different sandstone cores obtained from the field, properties including specific gravity, specific heat capacity, thermal diffusivity, and porosity, along with thermal conductivity, are determined and highlighted in this study.

Jul 20, 2021

By Rameshwar Sah, L. R. Singh, SIVALINGARAJU BARISETTY, SHYAM YADAV, P. K. Ghorui

Fly ash is a by-product generated from combustion of coal in thermal power plant. Disposal of fly ash is a major environmental concern for the power plants. Though a considerable part of fly ash is used in cement making and brick manufacturing, substantial quantity remains unutilized. Silica and alumina are the major constituents in fly ash along with lime. Aluminosilicates and unhydrated lime present in fly ash, in presence of water, undergo a pozzolanic reaction and form cementitious bond which holds the particles together. Bentonite is commonly used as binder in micropelletization of process waste to attain the mechanical strength required for handling and transportation. The bonding of particles by bentonite is a physical mechanism, while fly ash bonding is a chemical mechanism. The present paper deals with the partial replacement of bentonite with fly ash in micropelletization without affecting the quality of micropellets.

Jul 30, 2021