Search Documents

By S. Hodgson

Introduction The Red Dog zinc/lead deposit in northwest Alaska is the second largest zinc deposit ever discovered. Being developed by Cominco Alaska, with startup scheduled for early 1990, it will ultimately be the largest zinc mine in the Western World. Table 1 shows the reserves of the deposit. Bob Baker, a local bush pilot, discovered Red Dog in 1968. The US Geological Survey assessed the find. But the Red Dog site had been withdrawn from staking by provisions in the Alaska Native Claims Settlement Act of 1971 (ANCSA). Under the terms of ANCSA, the deposit was selected by the NANA Regional Corporation, one of 13 native corporations established by the Act. Then, in 1980, the US Congress confirmed this selection, in the Alaska National Interest Lands Conservation Act. In 1982, Cominco and NANA reached an agreement that has led to the development of the mine. Under the agreement, Cominco leases the property from NANA, develops and operates the mine, and markets the concentrate produced. In return, NANA receives royalties and, after capital recovery, participates in the net proceeds from the operation. The Alaska State Government is also playing a role in the development of the mine. Under the auspices of the Alaska Industrial Development Authority (AIDA), the state will construct, own, and operate the DeLong Mountains Regional Transportation System. This consists of a 84-km (52¬mile) road from the minesite to the Chukchi Sea. Located here are the port facilities necessary to store and ship the annual concentrate production and receive the mine fuel and supplies. For using this transportation system, Cominco will pay an annual toll fee. Over the anticipated 50 year life of the operation, the fee will provide a 6.5% return to the State of Alaska. In late 1986, Cominco's Board of Directors approved the Red Dog project. And, during the summer of 1987, road construction began. In February 1988, initial stripping began at the ore body and construction started at the millsite. Project setting The project site is approximately 1000 km (600 miles) northwest of Anchorage, 84 km (52 miles) east of tidewater on the Chukchi Sea, and 192 km (120 miles) north of the Arctic Circle (Fig. 1). The countryside consists of low, rolling hills that lead into mountains north and east of the deposit. The vegetation is typical tundra mat. And the site is in an area of permafrost. However, the permafrost is relatively warm and some areas have been found to be thawed. Examples would be creek bottoms and the site of the main waste dump.

Jan 12, 1988

By N. H. Coates

The Bureau of Mines designed, constructed, and operated an 18-inch- diameter, fluidized-bed combustor for highly caking coals to evaluate the method for possible application to power generation. In initial tests, combustion was carried on successfully, with carbon losses as low as 0.8 percent. Coal ash was not satisfactory as a bed material, but mullite proved to be acceptable. Overall heat-transfer coefficients from the bed (-20 + 50 mesh mullite) to a water-cooled tube were about 75 Btu/hr-ft2- °F.

Jan 1, 1970

By R. H. Thorpe

In the earliest days of mining coal the obvious method was by bord and pillar working. Longwall in Britain developed from this as an expedient to overcome bottlenecks arising from ? 1) increasing depth of seams causing roof control difficulties; and 2) ventilation problems. This system became almost universal particularly in the thicker seams, where faces of up to one mile in length were not uncommon. Coal getting in these faces was usually by pick and shovel, filled into small waggons of up to 15 cwts capacity. These waggons ran on rails laid alongside the coal face and were often taken away from the face to the main haulage roads by horses. The roof was supported by rigid props and the wastes were normally controlled by strip packing. This system of mining was very flexible and worked well down to sections of about 3'6"

Jan 1, 1976

By J. L. Heaver

All complete plant foods require phosphorus, nitrogen and potassium. And phosphate rock is the primary source for the phosphorus of the inorganic fertilizers. As more and more world food production is grown with these chemical fertilizers and since the Florida field supplies over 30% of the phosphorus component, let us look at the vital phosphate industry. Mining of phosphate rock in Central Florida began in 1891 and production has continued to grow at a steady pace. In 1965 a phosphate mine was opened in Hamilton County, North Florida and one in Beaufort County, North Carolina in 1966 . Since the beginning of mining in 1891, approximately 700 million metric tons of phosphate rock have been produced of this amount one-half was mined in the last 11 years. While the field was not deliberately "high-graded," the best of the known deposits were mined first. Those now being mined, and those yet to be mined, cost more to operate and the product is of lower grade. The U. S. Bureau of Mines' data for 1977 lists "Florida" phosphate rock production as 40.6 million tons; 86% of U. S. production and 85% of "Florida" capacity. The U. S. Bureau of Mines includes North Carolina production in "Florida" statistics so as not to reveal individual data for the one mine operating there. Approximately one-half of "Florida" production is exported, either as rock or as rock equivalent in upgraded products. Deposits of phosphate rock necessary to support present and future production are catalogued as: reserves, paramarginal reserves and resources. Reserves denote deposits which can be mined at a profit now. Paramarginal reserves are defined by the U. S. Bureau of Mines and the U. S. Geological Survey as: that portion of sub-economic resources that a) borders on being capable of production economically, or b) is not commercially available solely because of legal or political circumstances. The " b)" part of this definition may now be expanded to include environmental controls and requirements. Resources are deposits which cannot be mined at a profit at present. Listed in Table I are reasonable values for each of the three categories of phosphate deposits in the northern and southern parts of Central Florida. North Florida and North Carolina.

Jan 1, 1978

By Richard E. Thill

Engineering properties of rock are essential in most phases of mining from site reconnaissance through mineral processing. Review of the literature indicates, however, that property data is scarce for most coal measure rocks in the United States. The Bureau of Mines, U.S. Department of the Interior, has undertaken a wide-ranging testing program to provide more complete property data for coal strata in the U.S. coal basins. The property data are expected to have application in geophysical exploration, the development of pre- mining and hazard detection probes and instrumentation, mine design, engineering and rock mass classification, subsidence engineering, and ground control. This paper describes the comprehensive program encompassing in situ geological, geophysical, and geotechnical properties and laboratory determinations of acoustic, electromagnetic, physical, mechanical, and index properties and discusses results for 500 ft of coal measures at a minesite in the Northern Appalachian, Eastern Coal Province.

Jan 1, 1982

By W. J. Dolinar, S. P. Sandoval

The US Bureau of Mines (USBM) implemented the Fe2+/ Fe3+-SO2 anode reaction in a Cu-electrowinning cell with full-size electrodes. Electrowinning was conducted using industrial electrolyte at 258 A/ m2 (24 A/ft2) and 40°C. Manifold injection of electrolyte provided circulation between the electrodes. Five-day operation using an optimized manifold gave an average cell voltage of 0.94 V at 89% current efficiency, which amounted to an energy savings of 2.82 MJ/kg (0.355 kW-hr/lb), compared to conventional electrowinning. Acid milling 5was completely eliminated, and the SO2 concentration 23 cm (9 in.) above the cell averaged 0.06 ppm.

Jan 1, 1996

By J. A. Herbst

Until the past decade, the energy-size reduction relationship was the dominant form of mathematical model used in the description of tumbling mill grinding processes (1,2). Typically, in these models some single measure of product fineness (e.g. the 80% passing size, the size modules, the specific surface area) is chosen as the dependent variable and the energy input per unit mass of material being ground acts as the independent variable. In some instances these models have been useful for the correlation of experimental data, but, invariably, they have been found to be inadequate for meaningful process simulation. During the last decade considerable advances have been made in the development of phenomenological grinding models derived from population balance considerations (3-7). In these models a set of dependent variables is employed, corresponding to the set of mass fractions which constitute the product size distribution, and energy input is abandoned in favor of "time in the mill" as the independent variable. The phenomenological models have been shown to provide accurate simulations of the entire size distribution of ground products produced in batch (8-10), locked cycle(11)and steady and unsteady state, open and closed circuit continuous grinding(12,13).

Jan 1, 1973

By R. Y. Wan

Newmont Gold has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for the pretreatment of low-grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the preg-robbing characteristics of the carbonaceous matter in the ores. Therefore, an alternative heapleach process using ammonium thiosulfate was developed to extract gold from these preg-robbing bioaxidized ores. The ammonium thiosulfate leach process was successfully applied in both laboratory and pilot plant tests. Satisfactory test results were achieved, encouraging the continuation of process development.

Jan 1, 1997

By W. H. Schiffbauer

The U. S. Bureau of Mines has been investigating methods and technology that, when applied to existing continuous coal mining machines, may improve production and safety. Toward those goals, a microcomputer network has been designed that provides automated control and monitoring of all mining machine systems using a single twisted pair cable (two conductor stranded wire twisted together to provide a level of noise rejection). The network also provides -connections for intelligent sensors and systems for navigation and diagnostics. The flexibility of the network is demonstrated in that features can be added and removed without redesigning the whole system. A general description of the network's integration to a Joy' 16CM, Joy 14CM, Jeffrey 102, and a custom built auger machine is provided. The microcomputer networks for the Joy 16CM and the Jeffrey 102 have been installed onboard the mining machines and have been extensively tested at the Bureau of Mines test facility. The Jeffrey 102 system has also been tested in an actual highwall coal seam. Both systems have performed satisfactorily. The microcomputer networks for the Joy 14CM and the Auger Miner have been tested and await installation on the respective machines.

Jan 1, 1990

By Wendell R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems. Uncertain knowledge of abandoned coal mines also imposes potential hazards in current mining operations since water inundation or the release of methane gas is a serious hazard when mine excavation operations break into an abandoned mine. Requirements for detecting and mapping subversive man-made tunnels in previous work has led to the development of a surface- operated automatic earth resistivity survey system and associated computer data processing system for military applications. Field demonstration tests of this system have resulted in successful detection of tunnels at depth-to- diameter ratios greater than ten to one. Under the sponsorship of the Bureau of Mines, a similar high-resolution earth resistivity system was designed and constructed for use as a potential means of detecting coal mine workings. The hardware and software aspects of the new system are described together with applications of the method to the survey and mapping of abandoned coal mine workings. Field tests are presented showing the detection of both air-filled and water-filled mine workings.

Jan 1, 1981

By Margaret Armstrong

The increasing cost of developing new mines and the need to mine more marginal deposits have led mining companies to use more sophisticated estimation methods such as kriging. But until recently, coal mining companies have shown little or no interest in these techniques. However, the stringent quality controls which are now placed on coal have led to a surge in interest in improved estimation methods. This can be seen from the -, number of research projects by private companies and governmental agencies on the application of geostatistics to coal reserve estimation. At present, most of these programs are centered on the problem of estimating the tonnage and the average grade (i.e. ash percent, sulphur content, calorific value, etc.) of the coal in-situ. See, for example, Sabourin (1975), Woods (1976, 1979), Pauncz and Nixon (1979) and Armstrong (1980). These studies show that the established techniques of linear geostatistics can be applied successfully to coal deposits. The study by Woods is particularly interesting because he had access to the actual production figures as well as the initial sample data from the no 2 seam in the Greenside Colliery owned by the Anglo-American Corporation. He showed that the estimates obtained by kriging were consistently closer to the actual production figures than those given by three other estimation methods. This confirms the superiority of kriging as a method of estimating block values for coal. Another advantage of geostatistics is that it can be used to determine the optimal spacing between drill holes. An example of this is given by Armstrong for the coking coal deposit in the Bowen Basin, Australia.

Jan 1, 1981

A panel discussion on carbon-in-pulp processing of gold and silver ores was one of the highlights of the 1981 AIME Annual Meeting in Chicago. The session generated considerable interest and discussion among panelists and the audience. For those unable to attend the panel, the program was recorded and the discussion appears in this two-part report. The panel was co-chaired by Robert S. Shoemaker, vice president of San Francisco Mining Associates, and Laurence D. Hartzog, principal engineer with Bechtel Civil and Minerals Inc., San Francisco, CA. Panel members included: George Potter, consultant, Tucson, AZ; Kenneth B. Hall, metallurgical superintendent, Homestake Mining Co., Lead, SD; and Donald M. Duncan, resident manager, Pinson Mining Co., Winnemucca, NV. There have been several types of carbon-in-pulp adsorption vessels in use, such as the Dorr-type agitator, the simple propeller agitated tank, the Pachuca tank, and, lately, the draft tube-type of agitated tank. Which one of these is best and why? Potter: On the selection of the most appropriate adsorption vessel, there is a considerable difference of opinion that stems largely from the fact that every ore is different. The mesh of grind, the pulp solids, and the apparent viscosity of the pulp as caused by its clay content and chemical conditions all differ. The traditional Dorr agitator with the slow speed center sweep and either peripheral or center column air lifts has worked quite well on the finer grinds of all minus 65 and probably 70-80% minus 200 mesh. Pachuca tanks have also been successful and they may be capable of handling a coarser feed than the traditional Dorr tank. One uranium mill, for example, handles minus 28 mesh sandstone ore in a Pachuca. The most recent development and one that commands consideration is the draft tube agitator in which there is a turbine which closely fits inside a draft tube. Velocity in the tube is carefully calculated to avoid undue shear and thus abrasion of the carbon. The objective in all cases, of course, is to mix the granular carbon, which is typically 6 x 16 mesh, very gently but thoroughly in a slurry with minimum carbon abrasion. I do not know that there is one outstanding choice just yet and I have been unable so far to get information on C-I-P service for ore grinds as coarse as 35 mesh. Duncan: The major advantage of draft tube-type is the ease of startup. At the Pinson plant we installed draft tube-type agitators but it is too early to quote experience with them. We also haven't operated long enough to determine just what our carbon loss is. The advantage, of course, in the draft tube design is that it requires only about one-third the horsepower input of a conventional agitator. If it has no other advantages, it has that. Hall: The type of vessel most suitable for C-I-P adsorption depends on the type of ore treated and the prevailing operating conditions. In most cases, a deep tank with turbine-type mechanical agitator and low speed tip velocities would be satisfactory. Turbine-type impellers give a positive type of agitation which assures optimum ion contact and reduces short circuiting. Thorough aeration is possible with an air sparge properly located. A mechanical agitator can easily be started up after an outage, but it is usually necessary to drain and wash out a Dorr rake-type or Pachuca before restarting. The turbine-type impeller requires more power, but maintenance costs are negligible if rubber covered impellers are used. Carbon losses are minimal. In smaller plants, Pachuca type agitators provide adequate aeration and agitation. Bob Polak, Occidental Minerals (from the floor): Mr. Hall, you favor the mechanical-type agitator with the preface that the proper design is critical. Could you elaborate on this for us? Hall: The most important thing is low tip speed to prevent carbon attrition. I think the impeller should be sized so that you get a good sweeping action toward the bottom of the tank, across its bottom, up the sides, and back to the center. The advantage of the draft tube is that you get a more positive agitation and you probably get improved aeration too. Polak: Do you know of anyone using an upflow mechanical agitator rather than a downflow unit? Hall: I think that Bob Wilson at Custom Equipment has designed one where he has located the sparge directly beneath the impeller. The air bubbles are broken up by the impeller as the slurry passes through it. The slurry flows upward, outward, down the sides, and, again, back to the center of the tank. I don't know that any tanks of this design are in commercial use. Hans Von Michaelis, Randol International (from the floor): A question to any of the panelists on flat bottom versus conical bottom Pachucas. Hall: I would say the conical bottom would be most suitable in most cases. Some plants have experienced problems with flat bottom Pachucas in that they have a tendency to sand in on the sides of the tank so only the center of the tank is active. Duncan: With our draft tube tank we placed an inverted cone in the center of the tank bottom and blanked off the bottom comer around the circumference of the tank to facilitate movement of the pulp. Other than that, as far as conical bottom tanks are concerned, I'm generally opposed to them because of the cost and height differential. Larry Kramer, Kennecott Minerals Co. (from the floor): Mr. Duncan, you mentioned that the draft tube-type could be agitated with about one-third the horse-power applied to a conventional propellor agitated tank. I have trouble trying to pin down that kind of number. Could you give a bit of rationale as to why that mechanism has a lower horsepower requirement? Duncan: I think it has to do with the fact that below the propeller you have straightening vanes. The pulp, which is flowing vertically downward, is turned and flows upward again without any recirculation. You have an inherently less horse-power requirement in that type of tank. The one-third horsepower requirement is a number I obtained from Lightnin, which supplied us with details of the draft tube. There is probably much more recirculation with a conventional impeller type that is wasted motion. Potter: Last week I saw some agitators in South Africa with short draft tubes and actual turbine-type impellers. This plant was handling 200 kt of ore per month. The tanks were flat bottomed, and the agitation appeared to be quite satisfactory.

Jan 8, 1981

By E. R. Bollinger, N. S. Tanious, R. D. Beckett

The US Bureau of Mines developed hand-made, steel-fiber-reinforced concrete (SFC) blocks for building mine cribs. To ensure wider usage of these cribs, US Steel Mining Co. initiated a joint development and evaluation program with Burrell Construction Co. to mass produce SFC blocks of reasonable dimension, weight, and cost. Small specimens and full-size cribs were evaluated to determine their compressive strength and post failure characteristics. After testing and adjusting of various concrete mixtures, a final formulation was selected that gave a nominal crib strength of 22 MPa (3200 psi) and a nominal modulus of elasticity of 6.9 GPa (1.0 x 106 psi.) These SFC cribs can support 6.4 times as much as a wood crib with the same load-bearing area. The SFC crib was proven to be an economical and effective roof support system through various underground installations.

Jan 1, 1987

By Ted Nye

This paper describes a number of aspects of the design and construction of a driven tunnel which forms part of the Boggo Road Busway project. The driven tunnel is 430m long with an excavated width of 15m and a full tunnel excavation height of 8m. The first section of driven tunnel was excavated under the heritage listed Boggo Road Jail for a length of 120m. The main jail buildings and perimeter walls were built in 1908 and are of brick construction. Ground cover over the tunnel beneath the jail site varied from 5.5m to 8m and as a consequence the predicted settlement values and their potential to cause damage to the buildings were critical to determining and obtaining approval for the selected tunnel alignment. The geology along the driven tunnel alignment was very variable, providing mixed face tunneling conditions and ranging from surface residual soils to high strength rock at depth. The maximum ground cover above the driven tunnel is 20m.

By Russell G. Hood

Rock bolting or anchoring are methods of stabilization which are not being fully utilized in California and probably in other parts of the world due to lack of understanding of the principles, or due to poor results in actual installation. The problem is greater in California because so much of the rock is either soft or badly fractured and broken. Almost any recognized type of rock bolt or anchor will perform successfully is hard, fresh rock, but the problems become many-fold when working in decomposed granites, shales, soft sandstones or other soft, highly-broken rock. There has been an enormous amount of research by manufacturers, consultants, private organizations, and governmental agencies on rock bolting. It would be impossible to discuss all the methods and philosophies of rock bolting in this paper. Therefore, with the indulgence of the experts, I will give only a very generalized coverage on rock bolting techniques. However, My main purpose is to point out some of the problems of rock bolting in soft rock.

Jan 1, 1967

By Barbara C. Schickner

No group has been harder hit by the problems confronting the coal mining industry than small, independent surface mine operators in the eastern US. Burdened by costly government regulations, major capital shortages, declining productivity, high unemployment, and idle and closed mines, many in the industry think the breed will not be able to survive much longer. But there are a few sole owners fighting to remain independent-and succeeding. John Wagner is running a coal stripping operation in northwest Pennsylvania on a unique blend of aggressive management and marketing, support from a team of blue-chip professionals, and some unusual tactics. Though Wagner's approach is hardly an across-the-board formula for survival-he is currently reorganizing under Chapter 11 of the Bankruptcy Reform Act-a look at his operation helps illustrate some of the unique problems confronting eastern surface miners.

Jan 2, 1980

By Daniel Threlfall

The disposal of hazardous chemical wastes will be one of the major environmental issues of the 1980's. Approximately 50 million tons of hazardous wastes are produced yearly. One of the major aspects of the problem is the siting, design and construction of environmentally acceptable disposal facilities to accommodate this huge volume of material. Surface mines have been considered attractive for development as disposal sires for several reasons: 1. Surface mines represent an open pit that can conveniently serve as a repository for wastes. This could represent a significant economic savings when compared with sites on undisturbed lands chat might require extensive excavation or embankment construction.

Jan 1, 1981

By Robert E. Goodwin

As man's need for minerals continues to grow and as the known mineral deposits become depleted, it may be expected that these increased demands will result in greater exploration for additional deposits and at continually increasing depths below the earth's surface. As labor and material costs continue to rise, the need for more economic material handling will be emphasized. The quest for heavier payloads, safely moved at faster speeds from deeper mines, will be vigorously pursued. Strenuous efforts are, therefore, being made in the wire rope industry to develop ropes with greater strength-to-weight ratios than presently available while maintaining the dependability and long life being received from the conventional rope manufactured today. For many years, high quality rope wire has been manufactured from rods of selected steel compositions. Carefully-controlled wire drawing combined with proper heat treatment has resulted in high quality wire and wire rope throughout this period. Refinements in the rod produced from specially-selected high carbon steels combined with the latest improvements in wire drawing and heat treatments have made it possible to manufacture higher strength rope wire of uniform composition and structure that is suitable for use in Special High Strength wire rope.

Jan 1, 1970

By Edward F. Nagle

Instrumentation engineers have recently devised practical methods of metering the net solids flowing in a hydraulic mixture. The solids flow rate is determined by measuring the specific gravity and the flow rate of the mixture. T e specific gravity is measured by a variation of the bubbler system. The flow measurement is made by a somewhat unorthodox orifice requiring field calibrations. The linear mixture flow signal is then multiplied by the specific gravity signal, which is directly proportional to the percentage of solids in the mixture, to produce a linear solids Slow rate signal. The computations in this system are performed by Sorteberg pneumatic relays. Having obtained this measurement, integration and automatic control of hydraulic solids flow are available. This system is useful in mining, drilling and dredging industries. It provides maintenance of the net solids flow rate and reduces power consumption. Automatic control will provide rapid stabilization of net solids flow rate and release operators from making menual adjustments. The advantages of this application are economy of operation and increased pump efficiency, This paper describes a hydraulic solids flowmeter system installed aboard a dredge. Its purpose is twofolds:- 1. 20 provide a summation of the net solids flowing 2. To make available a practical guide for the drag tender operator. (Dwg. GSD-2219)

Jan 1, 1958

By M. Akser, F. L. Pirkle, B. W. Stratford, B. Ipekoglu

To date, no ilmenite, rutile and zircon deposits of commercial importance have been reported in Turkey. However, information from recent reconnaissance activities indicates the possibility of an economically viable heavy-mineral deposit in the vicinity of Ormanli, which is located northwest of Istanbul along Turkey's Black Sea Coast. Consequently, beach coil sand-dune samples were collected from that area for additional analysis. Laboratory methodologies drat were designed to simulate standard industrial heavy-mineral plant practices were used to analyze and evaluate the samples. Based on these analyses and current market needs, none of the deposits in the Ormanli area qualify as a commercial heavy-mineral deposit.

Jan 1, 1997