Search Documents

By Tom B. Corry

INTRODUCTION Located approximately 48 km (30 miles) south of Dallas, Texas, use to be the site of the Superconducting Super Collider. For those of you unfamiliar with the project, this was a multi-billion dollar project taken on by the U.S. Government for the further advancement of technology, medicine, and science. Major components of the project consisted of a Linear Accelerator known as the LINAC; three accelerating rings known as the Low Energy Boosters (LEB), Medium Energy Booster (MEB) and the High Energy Booster (HEB); the East and West Campuses where the Inner Reactor Halls would have been located; and the 87 km (54 mile) main collider tunnel. Unfortunately, this all came to an end on December 6, 1993, with the termination of the project due to the Government's cancellation of funds. This paper will deal with the two of the underground contracts before the termination. These two contracts were the 1122 contract which ran from N25 to N40 and the 1130 contract which ran from N40 to N55. (See figure 1) The 1122 contract was awarded to us in July of 1992 and consisted of the excavation and support of six (6) shaft varying in diameter from 5.5 m (18 feet) to 8 m (26 feet) and ranging from 39.6 m (130 feet) to 61 m (200 feet) deep and the driving of approximately 13,100 m (.43,000 If.) of main collider tunnel. Our second contract, the 1130, was almost identical to our first

Jan 1, 1995

By R. G. Bradburn

The events which led to computer control of the grinding circuit at Brenda Mines are described, beginning with mill operating philosophy. High production rates are encouraged so that, despite severe upstream disturbances, a manual control method to meet this philosophy had developed. Unfortunately, due to the time interval between manual control adjustments, losses in production resulted. An analog control method was devised and, although superior to manual control in some situations, was found to suffer from several practical limitations. The data logging capabilities of a control computer seemed warranted. Circuit test- work combined with an analysis of operating data showed that (1) metallurgical personnel, at times could increase production rates by as much as 10 percent over that achieved by grinding operators, (2) the chosen data base required an increase of 2 percent or more to be statistically significant and (3) for a 2 percent increase there would be a significant rate of return of investment in a computer installation, Consequently one grinding circuit was fully instrumented, and a rented control computer was installed by Brenda personnel. Prior to installation, Brenda metallurgical and instrumentation personnel were trained in the use of the computer. An experimental program was devised with short and long term objectives. The short term objective was to develop a practical control strategy which would yield immediate production improvement. This goal has been met as described in this paper. Statistically significant increases in excess of 2 percent have been established. Work is being completed for the permanent installation of computer control on all four grinding circuits at the present time. Long term objectives are (1) off line analysis of the circuit using mathematical models of process units, (2) on line experiments to study alternative contol tactics, and (3) possible expansion of computer facilities to the crushing plant.

Jan 1, 1976

By G. H. Lewis, C. L. Krcil, N. S. Harding, D. E. Havekotte

INTRODUCTION Limestone injection work was completed in a 440-kW (1.5-million Btu per hour) pilot-scale combustor in preparation for a 50,000-kg/h (110,000-lb per hour) industrial steam boiler limestone injection test program. The main objectives were to: (1) identify the important variables that affect sulfur capture, (2) determine the maximum SO2 removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. A more detailed report is given by Lewis et al. (1985). The test program was divided into two phases. The objectives of Phase I were to determine the important variables that affect SO2 reduction and to investigate the effect of limestone addition on combustor operation and heat transfer surfaces. The objective of Phase II was to determine, using only the important variables identified during Phase I, the conditions that resulted in the greatest sulfur dioxide reduction. Phase I Test program Using one limestone, five variables were identified as having an effect on SO2 reduction. These are noted with their respective ranges: heat release rate [103 to 166 kW/m3 (10,000 to 16,000 Btu per hour-cu ft)], Ca/S molar ratio (0 to 3), flue gas oxygen concentration (3% to 5%), additive particle size [90% -150 µm (-100 mesh) and 90% -45 µm (-325 mesh)], and burner stoichiometry (SR = 0.75 and >1.15). A 2.3% sulfur northern West Virginia coal, pulverized to a nominal grind of 70% -75 µm (-200 mesh), was burned for the tests. The limestone used was obtained from a Maysville, KY, quarry and contained 51.75% (wt) CaO. An 11-run statistically designed program (plus three duplicates) was used to screen the five variables. The effect of limestone injection on the combustor heat transfer surfaces was determined by comparing the heat transfer rates through a slag panel and fouling probes during periods with and without limestone injection. Combustor operation was determined by noting any operating problems that occurred during the tests. Test procedure After furnace wall temperatures had stabilized at operating conditions, heat transfer surfaces (slag panel and fouling probes) and the convection section were blown clean, and a four-hour test was begun. The

Jan 1, 1987

By S. A. K. Forson, Newton A. Amegbey

In order to investigate production decline in Tarkwa Goldfields Ltd., located in a tropical rain forest, amongst other areas, a health survey was conducted with the aim to see 1. The health status of the workers. 2. Which parameters carry the most information about the health situation and which of them can be applied easily during screening programmes. 3. What steps could be taken to improve the situation. In all 249 workers were investigated. A non-invasive method involving taking of body weight and arterial blood pressure was used. All subjects were required to answer a questionaire. Emphasis was placed on the history of malaria and diarrhoea within the last six months. Both management and workers co-operated fully. Another set of 110 workers from a neighbouring tyre factory were also investigated for control. Among the underground workers, the percentage body weight loss during a shift increased with decreasing body weight. Dehydration levels could be as much as 4 to 5% of body weight. This could be attributed to the fact that workers took insufficient or no water during the shift. The health status of the mine workers was generally poor and in our opinion malnutrition combined with malaria severely threatens the health and well-being of the workers. Hypertension is also a problem. An improvement in production is intimately linked with the well-being of the workers.

Jan 1, 1989

By John M. Gullbert

It is the task of this portion of today's session on the new meaning of regional tectonics in the search for ore districts to discuss known interactions of tectonics and ore deposition in the 'new global tectonics' context. I will speak particularly about known applications of the recent tectonic advances to ore finding. Stated yet another way, it's getting on in time toward the "put up or shut up" stage-¬and I would not be here if I thought that the new tectonics were not an effective present matrix for ore finding. Before delving into specific geologic relationships--and I propose to discuss mainly the evolution of an idea which may reveal the presence of a major copper deposit on mainland Mexico--I must note that there have been no published accounts that I know of which assert that a particular discovery has been made soley and specifically because of an interpretation based upon mechanisms directly linked to sea floor spreading or plate tectonics. It is nonetheless true" that several major exploration efforts are based upon such interpretations, and, as is normal when exploration ideas are involved, one does not wish to call attention to an advantageous position in a highly competitive business. Little might be expected to have been announced in so fast-moving and potentially lucrative an area. Another point which needs to be made is that people such as B. S. Butler (1933), Billingsley and Locke (1935 and 1941), Harrison Schmitt (1935), and more recently Mayo (1958) have been working for decades with the tectonic expressions of the emergent tectonics without recog¬nition of the driving forces or the unifying tectonic concepts

Jan 1, 1971

By Douglas G. Brookins

Clay mineralogic studies of ore versus barren rocks in the Grants mineral belt show that some combination of chlorite (rosette form), illite, mixed layer illite-montmorillonite, (- Mg-montmorillonite) are penecontemporaneous with uranium minerals in trend ore; these same clay minerals plus kaolinite are related to the roll type ore near the main redox front of the Grants mineral belt. Clay minerals from barren rocks are characterized by a greater abundance of Na-montmorillonite, kaolinite, and face-to-edge form chlorite. Chlorites from ore zones contain much more vanadium than do chlorites from barren rocks. Trend ore probably formed from southeasterly flowing waters following paleochannels in the Late Jurassic. These deposits are found almost entirely in reduced rocks, and organic carbon may have been an important reductant to remove U-V-Se-Mo from solution as carbonate from ore zones contains some organic carbon based on stable iso¬tope studies. Uplift, remobilization and reprecipitation of some of the trend ore resulted in the formation of redistributed ore, some of which possesses a roll type geometry. Mineralization for the roll type ore was apparently controlled by sulfide-sulfate equilibria at or near the main redox front in the Grants mineral belt. Trend and roll type ore possess different assemblages of clay minerals and different trace element abundances. Laramide faults cut both trend and some roll type ore. Stack ore is found in Laramide fault zones. Limited oxygen isotopic data from clay minerals in two mines at Ambrosia Lake in reduced rocks indicate probable preservation of ancient, formational waters and no evidence for infiltration by young meteoric waters. This information, plus the pre-Laramide faults, suggest, but do not unequivocally prove, that the main redox front has been relatively stable since its formation, probably some time in the Cretaceous. Younger encroachment of the redox front in post-Laramide is proposed by others, however, and the problem is unresolved. Uranium for the deposits was most likely carried in solution as an oxyion, probably as (UO2(CO3)2.2H2O)2- or (UO2(HPO4)2)2-, although organic transport cannot be entirely ruled out. Oxyions of vanadium, selenium, molybdenum and possibly arsenic and antimony, are interpreted from Eh-pH diagrams to have been segregated and transported with U6+ soluble species and precipitated when a chemically reducing environment was reached. The rare earth elements are also enriched in ore zones, but it is not clear if they were transported with the U-V-Se-Mo-(As)-(Sb) suite or derived from a more local source.

Jan 1, 1980

By Carl E. Schubert

The application of geophysical technology relative to the exploration, planning, and operation of coal mines is expanding. This is due to the trend of the industry to increase the size of operations, use of mechanized equipment and mining of more difficult coals, where unforeseen conditions can affect mine profitability. Coal is a good geophysical target because of its lower density, higher electrical resistivity, lower seismic wave velocity, and lower magnetic susceptibility in comparison to typical country rock. The more important techniques are well logging, high resolution seismic reflection, seam wave velocity, and radar. These methods can be used to map coal horizons, determine the physical properties of the coal, and identify mining hazards. The methods are not a pancrea however. Their use should be based on a careful assessment of their expected success and cost benefit analysis in comparison with conventional technology, primarily drilling, which none of the techniques presented should entirely replace. In general, the level of technology developed for geophysics surpasses their current level of application to coal problems. In some cases, identifying hazards in advance of mining using seam wave seismic in particular, the state of the art has been developed in Europe and is awaiting fruitful application in the United States.

Jan 1, 1982

By J. L. Carr

On average, one to two fatalities occur every year when a miner is struck or pinned by a continuous mining machine (CMM). Proximity detection systems offer an effective means to prevent these types of injuries and fatalities by sensing the presence of a miner and automatically disabling machine motion. The Mine Safety and Health Administration (MSHA) is expected to finalize a regulation that would require the use of proximity detection systems on all CMMs. Approximately one-fourth of all CMMs in use in the United States are already equipped with such a system. The use of these systems will save lives, not only by automatically preventing accidents but also by acting as a tool for educating miners and reinforcing safe work practices. Researchers at the Office of Mine Safety and Health Research (OMSHR) have conducted a series of field evaluations to quantify the performance of these systems in an underground coal environment. These field evaluations measured the distance at which the warning and stop zones were activated. The technology provided consistent activation of the warning and stop zones under many of the conditions tested. However, some performance inconsistencies were observed which present opportunities to improve the reliability of proximity detection system technology. Some of the notable variables that caused significant changes in performance and should be considered in the design, implementation, and use of proximity detection systems include interaction with the trailing cable, performance changes during tramming, and orientation of the miner-worn component.

Feb 23, 2014

By G. P. Tomaino

Talc is a layered, hydrous magnesium silicate mineral. It has a soft, soapy feel and typically a smooth texture. Talc is also known for its insulation, heat resistance, chemical stability, oil absorption and strong covering quality. Talc, Mg3Si4O10 (OH)2, has a theoretical chemical composition of MgO at 31.7 percent, SiO2 at 63.5 percent, and H2O at 4.8 percent. However, talc’s chemical and mineralogical composition can vary depending on its geological history/parent rock association. These mineral associations and variable levels are usually chlorite and carbonates (magnesite, calcite and dolomite). Two key elemental substitutions that can occur in the talc crystal structure are iron for magnesium and fluorine for hydroxyl. These compositional differences may limit or enhance the talc’s usage in specific market niches. The United States remains self-sufficient in most grades of talc.

Jan 1, 2005

By S. C. Termes

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble crosslinked starch xanthate (ISX). ISX is insoluble, has a shelf life of over a year when kept cold, and has a higher molecular weight due to cross linking than the soluble noncrosslinked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines but not silicious gangue. Floc formation, floc size, and settling rate are strongly dependent on pH, with the pH dependence differing for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1982

By Yves C. Lizotte

Although blasting remains the most inexpensive method of fragmentation in hardrock mining, the significance of the costs of blast-induced rockmass damage in terms of mining efficiency and safety is becoming increasingly recognized. There is no straightforward and systematic method of adequately measuring blast damage in on-going mining operations. This paper considers various techniques available to measure blast damage, making particular reference to recent underground hardrock mine studies. It concludes by proposing a damage audit procedure for integration into routine mine production control.

Jan 1, 1996

By Ruoming Gong, Arindam Samanta, Ragula Bhaskar

Three studies conducted at the University of Utah relating to the effect of scrubbers on face airflow patterns, the resulting dust exposure of operators and the development of a throat scrubber for continuous miners are summarized in this paper. The first study involved full-scale laboratory tests to determine the potential dispersion patterns and transport of dust at a continuous miner face, using different ventilation configurations and a scrubber. Concentration maps were developed and potential exposures at operator positions were examined. The second study involved the development of a 3-D numerical model to predict airflow patterns generated by a scrubber at a continuous miner face. The model was designed to evaluate the role of various face parameters on airflow patterns at a miner face and to complement the full-scale testing. The third study involved the design and fabrication of a low profile hydraulically powered continuous miner throat scrubber. The scrubber uses three hydraulic motors and small diameter fans to draw about 3000 cfm (1.42 m3/s) of air and uses a flooded bed scrubber to filter dust particles.

Jan 1, 1993

By Henry A. Russell

During the last ten years Parsons Brinckerhoff has become a leader in the area of tunnel rehabilitation. A significant part of any tunnel rehabilitation program is the control of groundwater infiltration into the structure. This leakage over time, causes deterioration of the structures, and creates numerous operational problems for the tunnel operator. This paper will address current procedures for identification, documentation, and recommendations of repair methods for the control of groundwater infiltration in rail and highway tunnels.

Jan 1, 1993

By L. Barry Phelps

The complexity of surface mining operations is increasing as attention is directed towards mining larger tracts of lower grade, higher cost deposits. Large tonnage requirements from these mines necessitate utilization of many large pieces of equipment. This equipment must be utilized efficiently, with production maintained at or near designed capacities. Basically, the problem is to select, size, and schedule equipment to maximize profits and minimize adverse environmental impacts (Anon., 1977). The time, manpower, and cost limitations required to analyze a wide variety of situations and alternatives in planning surface mines have been sidestepped with the application of simulation methods using a digital computer. Since a simulator can be programmed to represent the situations which are to be analyzed, many alternatives can be evaluated in a relatively short time. Input variables are easily changed and the resulting changes which take place in the system can be analyzed. When standard methods of analyses are applied, weeks and many man-hours are involved in analyzing large-scale mining operations. At the same time many simplifying assumptions must be made since these operations are dynamic and transient. Hence, it becomes difficult to make sound engineering decisions and take proper and timely corrective action in the absence of simulation methods. This chapter is concerned with the application of one such method, namely, the open-pit materials handling simulator (OPMHS) developed by the Mining Engineering Section, The Pennsylvania State University (Manula, Albert, and Ramani, 1977).

Jan 1, 1979

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo' where svo' is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By Steve Kral

The mining industry has had three difficult years. Commodity prices have remained low and investor confidence in the industry has been shaken. And even though the Asian economy appears to be improving, it will be some time before this improvement will translate into better commodity price conditions for mining. In addition, increased environmental and social restrictions that have been placed on the industry in developed and developing countries have made mining a more difficult proposition. And, if that is not enough, the global mining industry has found itself in fierce competition with Internet businesses for investor capital. Despite that gloomy picture, more than 10,500 mining industry professionals from about 70 countries gathered in Toronto, Ontario March 5-10, 2000 for the Mining Millennium 2000 conference. This meeting was a joint effort between the Canadian Institute of Mining, Metallurgy and Petroleum(CIM) and the Prospectors and Developers Association of Canada (PDAC).The joint meeting also featured two trade exhibitions and more than 150speakers. PDAC’s trade show attracted about 400 exhibitors and an additional 200 in the concurrent Investors’ Exchange. CIM’s exhibition attracted about 600 equipment and service companies.

Jan 1, 2000

The issues involved in mine closure are usually complex, and the risks are significant. Although environmental risks are paramount, other issues such as safety, community, legal, fiscal and technical factors need to he taken into account. This paper describes a simple empirical model based on the concept of the closure risk factor, which will enable decision-makers to analyze the mine closure risks at any site, regardless of the complexity of the issues and the scale, scope and location of the operation. The model enables all the issues to be captured and their individual and collective risk quantified. A number of case studies in Australia and the Pacific that illustrate the usefillness of the model are presented.

Jan 1, 2002

By R. Hogg, S. Chander

An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example, in development of new processes, plant and process design, plant control, problem solving, etc.

Jan 1, 1987

By Sterling S. Cook

The U.S. Bureau of Mines is conducting core leaching experiments with sulfuric acid on oxide copper ores from the Cyprus Casa Grande and ASARCO Santa Cruz deposits in Arizona to further our understanding of the leaching process in supergene copper ores as it relates to in situ mining. Leach solutions from atacamite mineralization contained 5 to 30 g/l copper and few extraneous ions. Leachant from chrysocolla ores, with grades similar to the atacamite, contained 2 to 9 g/l copper and abundant extraneous ions. Quartz and K-feldspar had no impact on leach solution composition at any acid concentration (up to 40 g/l) while illite and sericite had minimal impact. Biotite, calcium-rich clay and limonite have a significant impact on solution chemistry when there is abundant free acid in solution. High acid concentrations increase acid consumption in ores with abundant biotite and limonite gangue. High acid concentrations can be used in ores with quartz, K-feldspar, and sericite gangues without increasing acid consumption per unit of copper removed.

Jan 1, 1988

By R. L. Grayson

The Office for Mine Safety and Health Research, National Institute for Occupational Safety and Health is responsible for providing research leadership in the prevention of mining work-related illness, injury and death. Planning of the NIOSH FY99 research program focused on the comprehensive collection and risk analysis of fatality, injury and illness data according to commodity and mine type. This data, coupled with the mapping of information obtained from stakeholder meetings over several years, provided the basis for prioritizing research needs. Results of the combined analysis were compared to the FY98 program to identify surveillance and research gap areas. The FY98 research program was then assessed according to commodity and mine type and compared with exposure assessments, traumatic fatality rates, injury rates and employment trends in each commodity-mine type combination to gain insight into the potential balance of the future research program. This paper presents the methods, data and results of this planning process.

Jan 1, 2002