Search Documents

By B. A. Ashley

Rosebud Mining Co. (RMC) is based in Kittanning, PA. As of October 2013, it operated 24 active underground mines in Pennsylvania and Ohio. RMC?s Tracy Lynne Mine is located approximately 5 km (3 miles) east of Apollo, PA, (approximately 48 km or 30 miles northeast of Pittsburgh, PA) and mines the Lower Kittanning coal seam. The coal seam averages approximately 1.1 m (45 in.) thick and is of steam coal market quality. The mine is a single unit operation. Coal is mined using a continuous mining machine and is transported from the face to the conveyor belt using a continuous haulage system. Typical ventilation in the mine consists of an exhausting fan that draws air through isolated intake, belt and return air courses (Fig. 1).

By Andrew Scogings

The current edition of The Australasian Joint Ore Reserves Committee (JORC) Code was published in 2012 and, after a transition period, the 2012 edition came into mandatory operation on Dec. 1, 2013. There is a significant change between JORC 2004 (Clause 44) and JORC 2012 (Clause 49) for the reporting of industrial mineral resources and reserves, which should be addressed by ASX-listed players in the industrial minerals space.

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By Nick Chlumecky

INTRODUCTION Column-type supports are used to prevent roof falls in underground excavations. The first individual column supports were made from timber that was cut to fit the irregular heights of mine seams. Because the seam height of the material removed varied throughout the mine, timber posts generally could be used only once. During the I 920s, steel friction props began to appear in British and European mines, and, by the 1950s, thousands of these props were being used. However, the steel friction props were heavy, difficult to install, and difficult to recover. Furthermore, the friction props could not be preloaded, and their yielding behavior was rather erratic. In 1946, hydraulic props were introduced in En¬gland, and, within a few years, they replaced friction props throughout Europe. The first application of hy¬draulic props in the United States occurred in the 1950s, during early experiments with longwall mining. Modern technology and high-production mining procedures have combined to make the use of hydraulic props a very acceptable method of providing temporary heavy-duty support for production areas. In areas such as development headings, where only modest roof loads are expected, lighter-duty jackscrews, ratchet jacks, and light hydraulic props are used. ADVANTAGES OF HYDRAULIC SUPPORTS The acceptance of hydraulic supports has been wide¬spread during the past 25 years, proving their reliability and effectiveness in preventing roof falls. Some of the advantages provided by hydraulic supports are: 1) Individual hydraulic props can be installed within 30 sec, resulting in a minimum exposure of per¬sonnel and equipment to an unsupported roof. 2) Hydraulic props can be preloaded to more than 4.5 t (5.0 st), increasing the frictional resistance between the rock strata. Thus, the roof is kept tight, improving the behavior of the unsupported ground. 3) If gradual roof sagging or bottom heaving im¬poses an irresistible force, the hydraulic prop yields gradually and continues to support the ground. 4) The support capacities of the hydraulic props most widely used range between 10 and 20 t (11 and 22 st). Their support capacities are maintained during yielding to an irresistible force. 5) Hydraulic props can be recovered rapidly. Where no other supports are provided for the roof, as in pillar¬ing operations, the hydraulic props can be recovered by remote means. 6) The length of hydraulic props is readily adjust¬able allowing them to be reused in seams where roof height varies. 7) Studies of mining operations indicate that the use of hydraulic props increases both personnel safety and mine productivity. DESCRIPTION Figs. I and 2 illustrate typical hydraulic props used in mines in the United States. Fig. I illustrates a prop

Jan 1, 1982

By M. Boucraut

After stating the advantages of the magnetic roasting technique as applied to iron ores, the authors report on technological research by I R S I D * in the field of magnetic roasting in fluid-bed furnaces This investigation was conducted first on an experimental two stage fluid-bed furnace which processed permanently 100-200 kg/h of ore, then on a three stage fluid-bed furnace with 1-2 t/h working capacity and at last on a 250 t/day pilot furnace The specific features of the IRSID process comprise - on the one hand, using special burners in the roasting reactor thereby ensuring a high production rate of the furnace - on the other hand, using a heat-exchanger where the preheating and cooling stages of fluidized ore are associated, so as to allow an efficient and simple cooling of both roasted ore and waste gases flowing out of the roasting reactor, thereby supplying heat to the crude ore and combustion air for the reactor burners Starting in 1965 the operation of the 250 t/day pilot plant at the Bazailles mine gave IRSID the opportunity of improving the conveying appliances and adapting them to the process, while perfectly confirming the metallurgical results obtained under ideal laboratory conditions

Jan 1, 1968

By Robert L. Somerville

As more phosphate deposits are discovered and new mines are developed, the necessity of critically evaluating various rocks for phosphoric acid production recurs ever more frequently. This need is accentuated by the increasing number of, fertilizer plants being constructed on deep water at various locations to serve world markets and to take advantage of locally-available sulfur or sulfur-bearing ores. A major proportion of all phosphate rock mined is consumed by wet-process plants and this acid in turn is consumed, usually captively, in the manufacture of fertilizer. It is apparent, therefore, that the first question asked by the developer of a new deposit is - How will it work in a wet-process plant? and conversely, when developing a deep water, project, one of the early studies required is - Which of the available rocks shall we use? What is the correct price to pay? How do we compare one rock with another? The economic importance of even minor aspects of these questions

Jan 1, 1966

By K. Y. Vasioutchkov, Y. F. Vasyuchkov, B. M. Vorobjev

In general a term "unconventional mining or "non-traditional mining technology" getting more and move familiar to the mining engineering media. There are several alternating terminological combinations such as "in situ mining", "borehole mining", "shaftless mining", "mineless mining", "geotechnology" etc.; specific terms denote particular method of unconventional mining technology: "underground coal gasification in situ", "underground coal combustion in situ", "borehole hydraulic coal mining" and others. Principal scheme of unconventional coal mining technology is shown in [Figure 1:] One of the greatest potential for coal utilisation during the beginning decades of on coming cetury is the synthetic fuel-gas derived from coal as a product of coal gasification. It is quite logical to enrich this gas before burning it with natural gas, that is methane, contained in coal measures. Thus it is reasonable to suggest a new concept of unconventional coal mining and utilization technology featuring integrated methane drainage with coal-gas combined cycle. Proposed unconventional technology of coal mining is characterized with: - opening up a coat deposit through boreholes, drilled from the surface and used for coalbed methane drainage as well as for coat gasification in situ; - aggregation of methane producing and coal gasification station on mining side with thermo power plant on the electric power generation side in one integrated industrial enterprise. The further improvement of the conventional coal mining technologies both surface and underground could give only insignificant results in economical, ecological and social aspects, but would not be able to provide basic requirements of the XXI-st century. Significant increase in economical efficiency, cardinal humanization of coal mining and basic improvements in environment protection would be achieved through introduction and implementation of innovative or unconventional coal mining technology. These considerations are applied on both coal production and coal utilization sides as far as coat based energy generation is concerned. Now a general opinion is widely spread that an application in the same manner of the traditional technologies of coal mining and electric power generation would inevitably cause further irreversible damage of the global eco-system, notwithstanding the certain environment protection measures being taken. Keeping the recent pace of the eco-system degradation the whole our civilization would be in danger. Thus the solution of this problem is to be found in developing, promoting and implementing in industry unconventional coal mining and modern advanced clean coal technologies. Coal reserves with favourable conditions at shallow depths are -being rapidly depleted in all countries with developed coal industry. So in nearest future more coat will be mined from deeper levels with higher operational expences and with lower labour productivity. For example in Russia only 20% of proven coal reserves can be specified in quality as easy mined reserves, i.e. coal reserves with a good minability. Unconventional (borehole in situ) coal mining enables us to mine difficult coal reserves, deposited under unfavourable geological conditions with higher economical and socio-ecological efficiency than that in conventional coal mining, in view of these the basic principles and concepts of coal mining and coal utilization for energy generation should be reconsidered taking into account the latest achievments in underground coal gasification/combustion, coalbed methane extraction, clean coat technology and advanced developments in environmental engineering. The authors have developed a new concept of ecologically clean and resource saving coal-gas electricity, protected by a patent of Russian Federation (1995). The main principles and technological features of these conceptual technologies are explained hereupon. It should be a break through into a coal mining technology of new generation, which is known as unconventional coal mining technology. Under current global energy policy, transection to the new generation of coal mining technology is inevitable. Now we are standing at the treshhold of the coat's regeneration based on integrated unconventional coal mining and innovative coal fueled electric generation technologies.

Feb 24, 1997

By D. J. Brunner, S. Mathur, D. McKinney

With the advent of faster micro-processors, the use of numerical methods to simulate complex fluid dynamic phenomena in three dimensions for use in design has become prevalent in the automotive, and turbo-machinery industries. The Computational Fluid Dynamics (CFD) method divides the region of interest into small control volumes which form the mesh representing the physical characteristics of the problem, and uses the finite volume method to intergrate the equations for the conservation of mass, momentum, energy and species over each control volume. Recent developments in CFD software expedite mesh generation, and enable the use of unstructured grids, comprised of tetrahedral volumes in three dimensions and triangular areas in two. CFD more accurately represents complex geometries and allows for relative movement of meshes enabling simulation of multiple moving bodies. 'ibis paper presents two examples of how CFD simulation can be used to assess mine and tunnel ventilation problems formerly addressed by application of analytical solutions which were developed assuming ideal incompressible conditions. CFD simulation is used to evaluate the impact of varying the airflow in a descentionally ventilated airway on the layering along the roof of smoke and hot gases resulting from a vehicle fire. Control of the smoke layer is required to enable safe egress from the vehicle, particularly if the vehicle is for personnel transport, and to ensure control of the fire contaminants throughout the ventilation system. The airflow required to prevent layering against the ventilation direction, calculated from the Bakke and Leach relations (Bakke and Leach, 1962), is compared with the CFD simulation results. An evaluation of the pressures, generated as a vehicle enters a tunnel portal, using CFD simulation, is also presented for unflared and flared portal configurations. These simulation results are compared with predictions derived using an analytical method which assumes one-dimensional and incompressible flow. Results of the CFD simulation are presented in an animated video format. SIMULATION OF BACKLAYERING In designing a ventilation system for a transit tunnel, the ability of the ventilating air to control and prevent backlayering of smoke and hot gases resulting from a vehicle fire is of prime concern. The buoyant nature of hot smoke causes it to rise relative to the colder, fresh air provided by the ventilation system. If the vehicle fire occurs in a descentionally ventilated tunnel, the smoke may tend to move upgrade in a layer above the incoming ventilation airflow. The layer may become thick enough to engulf a substatntial part of the tunnel cross-section upgrade of the incident that comprises the evacuation route. This effect is termed "backlayering' and it is similar to the development of methane layers in mines for which most studies related to backlayering have been done. Prediction Techniques Analytical A number of studies have been conducted (Bakke and Leach, 1962) to define the characteristics of this phenomena and as a result have produced relations which are used both in the mine and transit ventilation fields to define the air velocities required to control layering. In the transit industry the air velocity required to prevent the backlayering phenomena from occuring during a vehicle fire is called the "critical velocity" (Associated Engineers, 1975) and is dependent upon a number of factors: tunnel height, cross-sectional area and grade; ambient air temperature and density; and the heat release rate of the fire. Common practice in transit ventilation design is to provide an airflow which meets or exceeds the critical velocity. In order to determine whether or not the critical velocity can be achieved with a particular ventilation system, a one-dimensional simulation of the tunnel network is typically performed using programs such as the Subway Environment Simulation program (SES) originally developed in the late 1970's (Associated Engineers, 1980). The results obtained from SES are compared to the critical velocity to determine the adequacy of the ventilation system. Computational Fluid Dynamics For the backlayering simulations, a commercial CFD code which has been used successfully in a wide variety of engineering applications, was used. It provides numerous options for modeling laminar and turbulent flows, multiple turbulence models, definition of multiple species and chemical reactions between them, a variety of boundary conditions (including constant pressure and constant velocity inlets) and the ability to apply user-defined FORTRAN subroutines. It includes the ability to model conductive, convective, and radiative heat transfer. FLUENT also permits the use of "body-fitted coordinates" to match the computational mesh or grid to complex real-world geometries. Computational Fluid Dynamics Model The model developed to simulate the backlayering phenomena is comprised of an airway of rectangular cross-section, 4 meters wide, 4.5 meters high, and 200 meters long. A laterally

Jan 1, 1995

By R. A. Wharton, Z. Yang, R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al(III) and flotation collectors. It was found that the presence of Al(III) is necessary for good flotation of the organism, whether or not Pb(II) is present, when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8, and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al(III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminopropionic acid is used as collector, good flotation occurs at about pH 4 without the addition of Al(III).

Jan 1, 1992

By T. D. Parris

At the Frood Mine of International Nickel, tests were begun in March 1966 to evaluate the use of low profile diesel Load- Haul-Dump equipment in cut-and-fill operations. In December 1966, this test was extended to drawpoint loading of caved ore at the Creighton Mine. The results of these tests conclusively demonstrated the effectiveness of this equipment in the operations at International Nickel. This paper describes the equipment used, the operation of the equipment, production data and operating details. Also discussed in the paper are other trackless equipment which works with the Load-Haul-Dump carrier. Production and Safety comparisons are made with the slusher method in bulk mining, giving the reasons for replacing the slushers at the mines of International Nickel Company of Canada, Limited, Ontario Division.

Jan 1, 1969

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By Z. Jin, D. DePaoli, P. Zhang

"Phosphorite, or phosphate rock, is the most significant secondary rare-earth resource. It contains high amounts of phosphate-bearing minerals along with low contents of rare earth elements (REEs). In Florida, about 19 Mt of phosphate rock are mined annually and most are used to manufacture fertilizers using a wet process, in which sulfuric acid reacts with phosphates to produce phosphoric acid and phosphogypsum. In the wet process, REEs are also leached out into solution and eventually get lost in the leaching residue and phosphate fertilizer. Recovering REEs from Florida phosphate rock in the wet process will be beneficial to broadening rare-earth availability, improving the quality of phosphoric acid product and protecting the environment.This study focuses on the influences of wet-process operating conditions on REE leaching efficiency. The results indicate that REE leaching efficiency increases with phosphoric acid addition in the initial pulp. At a temperature of 75 °C, a stoichiometric ratio of sulfuric acid (H2 SO4 ) to calcium oxide (CaO) of 1.05 and a weight ratio of liquid to solid of 3.5, REE leaching efficiency reached a relatively high value of 52.82 percent. The trends of REE leaching efficiency were similar to those for phosphoric acid (P2O5 ). Extensive tests on the leaching residue showed that during leaching, about 90 percent of the REEs were released from the phosphate rock but only 52.82 percent ended up in the leaching solution. This phenomenon can be attributed to two factors: (1) the effect of phosphate ions (PO4 3-) in the solution, which caused REE ions to form REE phosphates and be precipitated into the leaching residue, and (2) the influence of large amounts of anions such as sulfate (SO4 2-), dihydrogen phosphate (H2 PO4 -) and hydrogen phosphate (HPO4 2-) anions as well as the polar molecule H3 PO4 , which surrounded the REE cations and formed an ion atmosphere that prevented the PO4 3- from contacting and combining with REE cations. Interaction of these two opposite effects determined the REE distribution between leaching solution and residue."

Jan 1, 2017

By C. Huang, S. Lin, Y. J. Wang

Introduction A mine characteristic curve is of great importance for both theoretical analysis and daily management of a mine ventilation network. Ventilation engineers are well acquainted with the ways of obtaining and using a mine characteristic curve that is conventionally associated only with single-fan networks. However, for a multiple-fan network, difficulty has long been recognized in defining the curve, not to mention, obtaining or using it. To extend the concept of mine characteristic curves for a multiple-fan network, a subsystem-based approach has been introduced by Wang (1992a). He defines a subsystem characteristic curve for a multiple-fan network and discusses the numerical procedure for constructing the curve. A graphical method of obtaining a subsystem characteristic curve for serial-parallel, multiple-fan networks has also been accomplished (Wang, 1992b). In spite of the maturity of the fundamental concepts related to and the numerical analysis tool for a multiple-fan ventilation network, information regarding the related laboratory tests is very scarce. To make up this gap, laboratory experiments have been done by using a two-fan experimental network. This paper presents the methodology and major findings regarding the construction and features of a subsystem characteristic curve. Characteristic curves and measurement fundamentals A characteristic curve A characteristic curve is a graphic presentation of the relationship between any two variables of a two-terminal component. It is typically defined in the form of a quantity-pressure curve for a ventilation component, which can be a single branch (airway), a fan, a regulator, a portion of a network or even a whole network. If a component is a single branch, the curve is called a branch characteristic curve. If it is a fan, then the curve is called a fan characteristic curve, and so on. Figure I illustrates the characteristic curves of some typical ventilation components. A general method for obtaining a characteristic curve from measurement is to apply an adjustable-pressure source between the two terminals of a component and measure the quantities corresponding to the different pressures. Mine characteristic curve A single-fan network can be easily divided into two ventilation components, the fan and the remaining network. The latter consists of only branches and regulators. Under this subdivision scheme, two characteristic curves can be constructed. They are the fan characteristic curve and the characteristic curve of the remaining network. The latter is referred to as the mine characteristic curve or the system characteristic curve. Although the general method for constructing a characteristic curve from measurement can be applied to obtain a mine characteristic curve, there is a shortcut for constructing the curve by introducing a mine resistance factor R. It is a constant if all of the resistance factors in the network are constant. R relates mine pressure H with quantity Q as in: H=RQ2 (1) For a given R, Eq. (1) can be directly used to plot a mine characteristic curve by assigning a series of Q values and calculating the corresponding H values. Hence a shortcut to constructing a mine characteristic curve is to measure one set of mine pressure H and quantity Q values, calculate the mine resistance factor R using Eq. (1) and then plot the curve. Subsystem characteristic curve Applying a similar scheme as is used for a single-fan system, divide a multiple-fan network into two components, a fan under consideration and the remaining network that contains all the other elements (branches, regulators and remaining fans) of the network. The fan under consideration

Jan 1, 1994

By K. Y. Haramy

Deep coal mines with strong roof and floor rock frequently encounter face and rib bursts. The burst problem is becoming more severe as mining depth increases, prompting efforts to relieve high stress areas ahead of mining. Successful stress relief reduces the occurrence of uncontrolled coal bursts. This report by the Bureau of Mines, U.S. Department of the Interior, presents a review of the most widely used methods to detect and destress high stress zones along coal faces. Stress-related burst problems and destressing efforts at a cooperating mine were investigated. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three- dimensional, multiple-seam computer modeling program, "MULSIM?, was used to evaluate the effectiveness of stress relief methods. Modeling results and guidelines for destressing are presented. Results indicate that dangerously high stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1987

By Clifford R. Haryett

The potash industry in Saskatchewan, Canada, has advanced in numerous mining and ore processing areas over the last decade. This article describes these innovations and their effect on the industry in the area. During the 1970s, Canada's Saskatchewan province became a world leader, second only to the USSR, in potash production for crop fertilizer. Despite a serious oversupply in the early part of the decade, and a drop in demand due to the agricultural impact of the oil crisis, the Saskatchewan potash industry continued to make extensive capital expenditures to bring mining and processing innovations onstream. These innovations were directed at reducing production costs, improving work conditions, and overcoming environmental concerns.

Jan 8, 1982

By C. Yao, T. M. Yegulalp

The scale effect on rock properties has been discussed and studied since the introduction of the weakest-link idea by Weibull (1939). In this study, the capabilities of a dynamic lattice network model to simulate failure of rock under uniaxial tension is utilized. A number of randomly distributed microcracks that contribute to the development of uneven stressfields are introduced. In addition, each unit element in the model is assigned a random value representing its strength properties. Each application creates a randomly created specimen that is subjected to uniaxial tension. The specimens are grouped into three sets according to their size. The results of the study show that the scale effect is present in a statistical sense, i.e., the observed statistical distributions of strength for each specimen group is distinctly separate, and they follow the expected inverse relationship between strength and size. The observed probability distribution for each group of specimens give rise to the estimation of a different set of parameters. In this paper, the potential relationships among these parameters as a function of specimen size is investigated.

Jan 1, 1999

By Jack G. Quade

During the summer and fall of 1973 a series of Skylab and high-altitude aircraft overflights provided excellent hard-copy photographs of the Great Basin. These photographs, with a wide range of ground resolution were used by the NASA Project of the University of Nevada, Reno, to conduct specific geologic studies. The principal objectives of these studies were to: select individual areas covered by Skylab photography for detailed studies, develop mapping techniques using varied film-filter products with a wide range of ground resolution, compare the results of the mapping techniques to existing geologic maps at comparable scales, verify the results wherever possible by direct field observations. These studies were conducted by Jack Quade and Dennis Trexler and by graduates and undergraduates of the Reno campus under a contract with the Manned Spacecraft Center Houston, Texas.

Jan 1, 1976

By M. V. T. Da Silva, J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The São Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999

By R. Vergunst, E. A. Devuyst, G. Robbins

By the middle of 1989 Inco will have applied its patented cyanide removal technology to seventeen commercial operations. Removal of cyanide from CIL slurry tailings is applied at Equity Silver and Inco's new 1.200 mtpd mill at Inco/Golden Knight. Detoxification of CIP tailings is carried out by Colosseum California (3.600 mtpd), Canamax's Ketza River (360 mtpd) and Westmin's Silbak Premier (2000 tpd) operations. Repulped tailings from Merrill-Crowe flowsheets are treated at Total Erikson's Mount Skukum (300 mtpd) and Skyline's Johnny Mountain (200 mtpd) mills and barren bleed at Inco/Queenston's McBean mill (500 mtpd). Lynngold's MacLellan mill (1800 mtpd) and ERG (40.000 mtpd) treat pond supernatant water. Plating shop cyanide effluents are decyanized at Kuntz Electroplating and two other plating shops in Ontario. Details regarding some of the above operations are given. Operating and capital cost estimates for various treatment options are discussed.

Jan 1, 1989

By H. Sato, B. Thornton, K. Nishi, A. Usui

"Northwestern Pacific submarine seamounts are believed to be future marine mining areas of ferromanganese crusts, which contain hi-tech industrial metals, such as Co, Ni, Te, Ti, Pt, and REEs. The Takuyo No. 5 seamount is a member of the Cretaceous super-plume seamounts in the north Pacific, located within a Japanese EEZ (100 nm from the Minami- Torishima Is. or Marcus Is.), and only 300 nm away from the Japan’s Licensed area for exploration of Co-rich ferromanganese crusts under the ISA. This is an on-going program supported by independent academic communities but not a state-run program or managed by private funding.We have observed, sampled, measured, and analyzed the occurrences, distribution, physical properties, and microbiological environments at a selected flat topped seamount named Takuyo No.5 as a model area for scientific study of ferromanganese crusts within the Japanese EEZ. We then characterized crust structures, composition, age, and growth history, resulting in an understanding of the overall nature and distribution of these deposits from wide range of areas, water depths and geological environments. The study started with a ROV (Hyper-Dolphin 3K of JAMSTEC) exploration jointly with universities and national institutions (Japan Agency for Marine-Earth Science and Technology, Japan Oil, Gas, and Metal Exploration Corporation, and Geological Survey of Japan) in 2009 using marine geology vessels, remotely-operated vehicle, an oceanbottom drill machine, deep-tow TV camera, as well as conventional dredges and corers. We have been studying the topography, geology, nature of the bottom material of the seamounts using delicate sampling devices and measurement tools, and characterized the distribution patterns of the metal-rich ferromanganese deposits from chemical, mineralogical, and microbiological points of view."

Sep 1, 2014