Search Documents

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By N. Champigny

The geostatistical estimation of the reserves of an ore deposit is highly dependent on the quality and stability of the variograms of the sample grades. Gold deposits commonly show a skewed grade distribution. The few high grades at the tail end of the distribution produce unstable variograms that are difficult to model. If these grades are cut to a lower grade value or removed, more stable variograms are obtained. However, outlier grades may make a deposit economically viable, and their cutting or removal should be treated with caution. To reduce (but not to eliminate) the effect of high grades, a transformation of the raw data can be performed. Most commonly used transformations are: logarithm, gaussian anamorphosis, rank and indicator. Variograms of the transformed grades are resistant to high grades and present a clear structure. The weak point of data transformation appears when grades are estimated by kriging; the estimates are very sensitive to slight variations in the parameters of the back-transformation. More robust variogram estimation procedures can also be used, but often these procedures are not suitable for skewed grade distributions as they are based on an assumption of a contaminated normal distribution. The Porgera gold deposit in Papua New Guinea has a highly skewed grade distribution, with grades ranging from 0.01 to 3500 g/t and a coefficient of variation greater than 5. For the geostatistical estimation of the high grade zone of the deposit, the influence of the high grades was quantified by calculating and comparing the following variograms: raw grades, raw grades with the highest grades removed and transformed grades. The study confirmed that there is no general method for handling high grades in a geostatistical reserve study. Several methods should be tried to quantify the influence of high grades.

Jan 1, 1991

By K. K. Bhattacharyya

Vast deposits of lignite occur in the Gulf Coast states and northern plain states. Lignite resources are cited to be over 43 billion tons in the Gulf Coast states. An additional resource of 16 billion tons are reported in North Dakota (Jackson, Smith, 1981). All lignite in the U.S. is mined at present by the open pit method. Draglines and scrapers are primarily used to remove the overburden. Bucket-wheel excavators are also being considered for new mines in the planning stages. Lignite seams are mined using front-end loaders, shovels and trucks, or Easi-miners. The depositional environment of lignite is weak sedimentary soils and rock. Ground water is often encountered within the mining depth. Surface water resulting from heavy rainfall or snow melt contributes to the problems of mining. Mining depths of up to 60 m (200 ft) are under consideration. Draglines exert additional loads on the highwalls and spoil piles. The combination of any number of these factors may cause instability of the slopes. Bearing pressure, trafficability, and settlement can also be a problem for excavation and loading equipment.

Jan 1, 1982

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert systems designed for real-time processing plants that also include the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. [1,2] In spite of the fact that significant performance increases have been achieved using these systems they are not perfect and can be improved. They suffer from the static nature of their rules and to a degree the process models. There is an opportunity to further increase system performance by systematically taking advantage of the tremendous amount of data produced by the expert system to improve the design, the heuristic rules, the model topologies and the use of the models. Data mining refers to extracting or mining knowledge from large amounts of data where the objective is to automatically analyze, classify and summarize the data to automatically discover and characterize trends in it and to automatically flag anomalies. [3] Clearly, modern process control systems are capable of collecting vast amounts of data. Without a doubt, these data contain important information on the operation of our plants and their ultimate optimization. Coupling the information mined from these data with Expert Control Systems should produce more effective control and greater knowledge of the grinding process and the flotation process. Now, with the advent of effective monitoring of entire minerals plant electric consumption it is possible to not only optimize plant production in real-time it is possible to analyze total plant electrical consumption and incorporate it into the plant control logic thereby improving the overall plant economic performance. This is particularly important with the ever more complex power contracts that plants operate under.

Jan 1, 2012

By d&apos, J. A. Oliveira, A. K. L. Resende, L. F. G. Assumpção, J. D. Neto

Kaolin samples from Rio Capim Resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the impurity removal process. Two coating clays and a delaminated clay were tested. The variables studied were retention time (cross-sectional velocity), magnetic-field intensity and matrix type. The feed brightness ranged, from 84.7% to 87.6% ISO, for the coating clays and ranged from 80.7% to 85.4% ISO for the delaminated clay. Using a conventional magnetic separator with an applied, field of 1.5 to 2.0 T (tesla), the brightness values were higher than 88% ISO for the unleached coating claw products and were higher than 87% ISO for the unleached delaminated product. With a maximum field intensity in the superconducting machine of 5.0T unleached brightness values higher than 88.5 % ISO were attained for both coating and delaminated clays.

Jan 1, 1997

By Heinz Hoberg, Fred Ulrich Schneider, Rudolf Diegel

The risk of contamination of dumped tailings and ground water by coal flotation reagents has been investigated by using the 14C-radiotracer method for adsorption and desorption measurements. The results indicate, that a high amount of the reagent components adsorbed on the tailings if there was no coal in the pulp. In coal flotation however a competitive adsorption behaviour could be observed, with the effect that only a low quantity of reagents adsorbed on the tailings. Mobilization tests showed, that only small quantities of reagents could be desorbed by rinsing water. Therefore the contamination of ground water should be low.

Jan 1, 1995

By B. H. Richard, P. J. Wolfe, T. G. Holdeman

Guided seismic wave propagation was studied in the Lower Freeport (6A) coal seam in the Oak Park No. 7 mine near Cadiz, OH. Three component geophones were implanted in the coal at distances ranging from 72 m to 183 m from the seismic source. Both Love- and Rayleigh-type modes were observed but the Love-type mode produced the best data. Detailed analysis was performed on the best Love data and a Dziewonski map of group velocity vs. frequency was constructed. This map was in excellent agreement with a theoretical dispersion curve calculated for a model of the coal seam. The Love wave group velocity was found to have a minimum value of 510 m/sec at 275 Hz. Only the fundamental mode contributed significantly to the observed signal and it was observed up to the maximum distance available.

Jan 1, 1987

By J. F. Strunk Jr., K. M. Maestas, Y. Chai, R. Legrand, R. L. Henry

"Groundwater with elevated sulfate and metals was treated using a sulfate-reducing pilot PRB consisting of a series of six 55-gallon drums filled with ZVI (Fe0), wood chips, brewer’s grain, limestone, and emulsified vegetable oil (EVO). Sulfate was reduced from >3000 to <250 mg/L and Cd, Cu, Mn, Ni, and Zn concentrations declined up to 3 orders of magnitude in 2 months. After 6 months of operation at a 7.5-day retention time, sulfate broke through. The system was then rejuvenated by injecting EVO in each drum and operated for 5 more months at a 9-day retention time. Sulfate-reducing bacteria in the pilot system grew by 3 to 4 orders of magnitude in 2 months. Some cementation of the PRB media was observed in the first 2 drums after processing 25 pore volumes of water, due to preferential upstream precipitation of sulfides; this can be avoided through operational modifications. Resulting permeability losses were estimated at 0.1% to 1% per year. Absorption/desorption was tested at bench scale to evaluate the use of various oil-soaked sorbents as a slow-release source of dissolved carbon. The tests show that oil sorbents can increase the useful life of a PRB between oil refills to over 100 pore volumes. INTRODUCTION High sulfate concentrations, low pH, and dissolved metal exceedances are common characteristics of mining-influenced water (MIW). Above-ground such MIW is commonly treated using biochemical reactors (BCR). In a BCR, water generally flows vertically downward through a layer of biomass, such as wood chips, manure, etc. The dissolved organics resulting from the decay of this material are oxidized first by microbes using oxygen; when oxygen is exhausted, other bacteria can use nitrate, and then sulfate to oxidize organics. Sulfate-reducing bacteria (SRB) reduce sulfate to sulfide, which quickly reacts with metals to form largely insoluble and stable metal sulfides. These reactions can be summarized as follows:"

Jan 1, 2016

By Chien D. Ngo, Andre Bachmann, Rainer Bunge

The remediation of contaminated sites has gained great importance in many industrialized countries. One method for cleaning the polluted soils from such sites is "soil washing," the scope of which is the separation of the contaminants from the soil. Soil washing is an outstanding example for a successful transfer of technology from Mineral Processing to Environmental Engineering. This presentation intends to introduce the Mineral Processing Engineer to soil washing through a short review of the fundamentals, and the discussion of an example for a successful soil cleaning operation in Switzerland.

Jan 1, 1995

By Albert E. Ketler

The AirBoss*200 is a unique ambient airflow sensor with important improvements in accuracy, especially in the critical low end, 0-61 m/min (0-200 fpm) where MSHA regulations apply. All solid state, its design is rugged, and there are no moving parts or delicate filaments. An on-board microprocessor calculates air velocity, linearizes and corrects for temperature, while driving voltage and current loop analog outputs to .3 meters/minute (1 ft/min) resolution. Recent developments also cover both positive and negative flow directions. A hand held computer is available to readout data and to adjust stored range selection, alarm set points, calibration data and the speed of response. Installation in hazardous areas is covered by MSHA Classes G, H and L.

Jan 1, 1993

By M. Botz

For leach solutions containing primarily free cyanide, the silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method significantly over-estimates the concentration of free cyanide and under-estimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric titration method for determining WAD cyanide that overcomes issues with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to fully release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, accurate WAD cyanide measurements were achieved using the MP-WAD method. Analyses obtained with the new method were found to be within about ±10% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.

Feb 27, 2013

By J. Harrison Daniel

Increasing concerns of industrial hygiene and worker health issues and resulting regulatory actions, coupled with continuing advances in mining systems, are placing new burdens on the industry and Federal Government; particularly, mine ventilation departments. More encompassing worker health programs are required to respond to Federal promulgation of regulations and to keep abreast of techno- logical advances in the mining industry. The relationship between the mining industry and Federal agencies involved in rulemaking is presented, along with the rationale of an Industrial Hygiene Management Plan. This plan or strategy focuses on developing partnerships and collaborative research groups to address the controversial health issues facing not only the mining workforce, but our society.

Jan 1, 1993

By J. E. Powell

Introduction The disposal of mine tailings, development rock, and other unwanted refuse material underground in mines by using pneumatic conveying techniques has been undertaken in the coal industry for many years. Similar equipment has been utilized for backfilling hard rock mines and is currently being applied in a gold mine in South Africa where development rock is being stowed in the mined-out stopes to help reduce the incidence of rock outbursts. On a limited scale, pneumatic conveying has been applied for backfilling uranium mines and one particular mine in New Mexico, U.S.A., has used this technique for 8 years. Other uranium mines in this area are now considerinq the dry backfill technique to eliminate the problems associated with hydraulic fill. The need to backfill in uranium mines is primarily of importance to improve ventilation, stabilize the pillars and roof, and possibly to extract a larger percentage of the uranium ore. If this can be achieved by utilizing the tailings from the beneficiation plant and using rock from the development headings which in itself may be slightly radioactive, then a greater benefit can be derived. Backfill can be achieved with hydraulic fill methods by running slurry into the stopes and allowing the water to decant and return through the footwall development entries to sumps for pumping to the surface. However there are several disadvantages associated with this method in that water is percolating throough the mine workings; it is necessary to build bulk heads in flat lying deposits; it is difficult to fill right to the back; and the decanted water takes with it quantities of the finer sand particles which results in maintenance problems with the mine pumps. Pneumatic conveying can overcome these problems in that the voids can be completely filled with high degree of compaction, heavy bulk heads are not necessary, the development rock can be added to the pneumatic system for disposal underground so eliminating hoisting cost to the surface, and cement can be added to the wetted material. To

Jan 1, 1980

By Tim Langmaid, Steve Skelhorn, Stephanie Robillard, Allen Mitchell

"The Port Mann Main Water Supply Tunnel project provides a critical water main crossing of the Fraser River for the owner, Greater Vancouver Water District (Metro Vancouver). The project consists of two 60-metre-deep slurry panel shafts and a 1-kilometre-long, 3.5-metre excavated diameter tunnel located near Vancouver, British Columbia, Canada. The initial tunnel lining is a precast concrete steel fiber reinforced gasketed segmental lining. The final lining is a 2.1-metre-diameter welded steel pipe. This paper describes the challenges encountered during tunnel construction and the solutions implemented. Key challenges include earth pressure balance tunnelling at up to 6 bar pressure—the highest to date in Canada—a water-crossing without surface access for the majority of the tunnel drive, ground freezing from a river platform for a critical TBM intervention, and boring through cobbles and boulders in dense glacial till. INTRODUCTION Metro Vancouver supplies drinking water to 18 municipalities, one electoral district and one treaty first nation, serving a population of more than 2.4 million residents. Water is collected in three mountainous watersheds to the north of the Greater Vancouver area, in southwestern British Columbia, Canada. To supply the growing demands of Metro Vancouver’s customers, treated water must be conveyed across two significant water bodies: the Burrard Inlet and the Fraser River. The existing Port Mann water main is one of several key links between the watersheds north of Vancouver and the municipalities south of the Fraser River. The Port Mann Main Water Supply Tunnel (PMMWST) is the first of a series of upgrades, to increase capacity, enhance scour protection, and improve seismic resilience. The new tunnel is 3.5 metres (11.5 ft) in diameter and 1 kilometre (0.6 mi) long. When completed, it will contain a new 2.1 metre (7 ft) diameter steel water main that will help ensure the continued, reliable delivery of drinking water to these municipalities, and will more than double the capacity of the existing 1.2 metre diameter main."

Jan 1, 2016

By J. F. Snyder

Minor elements determined by atomic absorption spectroscopy include: zinc, cadmium, copper, cobalt, nickel, chromium, manganese, and iron. Of these elements, only three; zinc, cadmium, and copper are found to have been introduced with the ore-forming fluids. Iron, manganese, chromium, and nickel were increased in dolo-stone lithologies when compared to limestone lithologies. The uniform distribution of cobalt suggests this element was neither increased nor decreased during ore emplacement nor during dolomitization of the rocks. Zinc increases adjacent to ore result from leakages into open spaces rather than as pervasive aureoles surrounding ore bodies.

Jan 1, 1977

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger&apos;s and Kick&apos;s laws (Bond, 1952). According to Bond&apos;s Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed.

Jan 1, 1994

By N. Edmonson

Frasch sulfur production/pricing decisions are based on market demand, less nondiscretionary sulfur supply. Price covers the cost of Frasch production and byproduct sellers accept the Frasch price structure. Large stocks have led Canadian byproduct producers to price aggressively at times, but their near-term drawdown suggests more passive price policies in the 1990s. Expanding continental nondiscretionary supply is combining with sizable Frasch supply increments to weaken prices. Simulations using a market model embodying these structural characteristics indicate that expanding demand may not result in substantial recovery from 1992 price lows before 1996.

Jan 1, 1995

By William R. Yernberg

The Fifth International Conference on acid rock drainage (ICARD 2000) was held May 21-24, 2000, in Denver, CO. The three-day conference consisted of about 150 oral presentations and poster sessions that described the state-of-the-art of acid-rock-drainage (ARD) science and technology. The conference also featured a trade show. It included representatives from consulting companies and government agencies with interests in ARD, as well as other environmental issues related to mining. The conference also included field trips to ARD treatment sites and short courses on acid rock drainage issues. ICARD 2000 was planned and promoted by the ICARD 2000 Organizing Committee and the Society for Mining, Metallurgy, and Exploration, Inc. (SME). Financial support was provided by Barrick Gold, BHP Copper, Homestake Mining, Noranda, Phelps Dodge, PlacerDome, the US Bureau of Land Management, the USEnvironmental Protection Agency and the US Geological Survey. Since the original ICARD was held in Roros, Norway, in 1988, knowledge has improved of the behavior of mine wastes as have methods of environmental mitigation. The ICARD 2000 presented the latest advancements in the field of acid drainage.

Jan 1, 2000

By Roy A. Grancher

CYCLING WITH CEMENT "THE WHEEL IS COME FULL CIRCLE" Shakespeare&apos;s King Lear Act V, Scene 3, Line 176 The time clock of the cement industry has been turned back to the early 1950s. After the trials and tribulations of the decade of the Sixties, the hands now stand where they did just over twenty years ago. Cement shipments have steadily increased, with a record 419 million barrel level (78.8 million tons) being reached last year. Plants are operating at average utilization rates in excess of 85 percent of rated capacity. The spread between supply and demand has narrowed to where a definite shortage of cement now exists within the industry. The notable and unfortunate difference between the two periods however is that, back then, cement&apos;s returns were a respectable 14 to 18 percent, whereas today they stand at less than half those levels. Insufficient return forms the present foundation of the U.S. cement industry. This lack is destined to have a cumulative effect. Just as the industry&apos;s balance between supply and demand is returning to favorable proportions, promising a period that has historically and now should generate those profit levels required to modernize and provide for capacity addition, cement instead finds itself frozen by federal price controls into the semi-depressed condition that has existed for over a decade and from which it was just starting to emerge. Capital is not attracted to continued low returns, and increasingly restrictive pollution control measures are necessitating great non-productive expenditures be made as definite costs to stay in business. Even a clouded crystal ball would reveal that additional cement plant closings can be expected.

Jan 1, 1972