Search Documents

By Louis I. Briggs

Evaporite rocks, salts of the more soluble ions in seawater, are deposited when seawater becomes concentrated by excess evaporation in marginal basins having restricted circulation with the open sea. The simple conceptual model of an evaporite basin (Figure 1) has a single inlet connecting the basin to the open ocean, the restriction to open circulation being caused by a bar or reef near the mouth of the inlet. As the oceanic water flows from the inlet into the basin it tends to form a thin layer of brine that spreads out over the surface of the basin brine, and as it does so, the salt concentration In the surface layer gradually increases owing to continued evaporation of the water. When the solubility products of the salts in the surface layer are exceeded, the salts precipitate and settle to the bottom of the basin, The order of precipitation follows their order of least solubility. Normally the carbonates separate first, followed by the sulfates and chlorides and the more complex double salts. In nature there is considerable overlap in their ranges of precipitation. The water flow in the basin, also shown schematically in Figure 1, diverges from the inlet essentially perpendicular to the lines of' equal salinity in the surface brine. The distribution of salts deposited in such a model will parallel the isosalinity lines, being arcuate and concave toward the inlet (1)

Jan 1, 1967

By J. Chae, D. Pecha, R. Andrews

The Henderson/ML King CSO Project is a major combined sewer overflow (CSO)reduction project for the Department of Natural Resources and Parks of King County, Washington. The central element of the project is the 3100 lineal feet long, 14'-8"diameter 42nd Ave S Storage/Treatment Tunnel. During the course of the project, the owner and consultants evaluated numerous elements of the tunnel including the alignment, geotechnical conditions, tunnel liner, and settlement monitoring requirements. The contractor utilized innovative shaft construction methods for the tunnel portals, and adhered to strict contract requirements in successfully constructing the tunnel. This paper provides an overview of the design and construction elements of the 42nd Ave S Storage/Treatment Tunnel that led to the successful completion of the project.

Jan 1, 2005

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania. West Virginia, Kentucky and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought but rather 200 in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Feb 24, 1997

By J. Philip Bromberg

The 1977 Clean Air Act Amendments will have a large effect on the coal-fired segment of the electric utility industry. Since electric power generation constitutes by far the largest single use for coal, this legislation has the potential to greatly affect future patterns of coal utilization in the U.S.A. The inability to depend exclusively upon low sulfur coal as an exclusive mode of compliance with New Source Performance Standards may greatly lessen projected demands for low sulfur coal by eastern utility boilers. The requirements of the legislation is discussed with particular reference to the needs of the electric generating industry, along with the technologies available for complying with the Act.

Jan 1, 1978

By John H. Bassarear

The never ending search for lower unit costs led Pima Mining Company's management to study various alternatives shortly after Expansion III was completed. It soon became apparent that a considerable amount of ore assaying 0.35% copper had to be moved in order to maintain mill feed at the desired 0.54% copper content, which is the overall grade of the ore reserves. Detailed investigations revealed that for a period of 8 - 10 years, about 14,000 tons per day of 0.30 - 0.40% copper ore would pass by the crusher en-route to the low grade stockpile. This ore is very hard, very clean and has to be mined at a relatively uniform rate. A six month pilot plant run testing autogenous and semi-autogenous grinding gave very encouraging results. Since no mining costs need to be charged to the extra tonnage (it had to be mined anyway) the only major costs would be against milling. The decision to proceed was made in August 1970 and Fluor-Utah was retained as the prime design construction contractor. Ore was first put through the new mill on December 29, 1971. By March of 1972 design tonnage of 14,000 TPD had been attained. The first three expansions at Pima Mining Company, 20 miles south of Tucson, increased mill capacity from 3,000 TPD to 36,000 TPD. These expansions included a separate, conventional, three stage crushing plant plus additions to the existing concentrator that primarily duplicated the then current flowsheet. Expansion IV, however, consisted of an entirely new and separate primary crusher and a completely new mill building located about 2,000 feet southeast of the 01 d concentrator. The new mill, using semi-autogenous grinding, produces scavenger and rougher flotation concentrates that are pumped to the old mill for regrinding, cleaning, thickening and filtration.

Jan 1, 1973

By Howard V. Sears

Prospecting in its modern context means simply the gathering of information on which, to base plans for the utilization of our mineral resources. One prospecting system familiar to T. V. viewers is the pan of the old gold prospector which, while he prospected, could produce the wealth which financed him in his search. Present day geophysical "prospecting" systems, which are based on the real or supposed responses of an ore specimen, to various stimuli finder controlled laboratory conditions, are promoted as means of reducing the cost of prospecting. The universal drawback to all geophysical systems is that they yield "soft" data which are only presumed to be analogous to ore mineralization until they can be calibrated, by conventional prospecting systems, to each actual mineral environment being tested. By this time the system usually is no longer cheap. Since the raw data are too esoteric to be used until interpreted by geophysicists, usually in the light of their own personal theories and experience, the certainty of multiple interpretation is introduced. The concept of prospecting, at St. Joe Minerals Corporation's Viburnum, Fletcher and Brushy Creek mines in the new Missouri Lead Belt, encompasses surface diamond drilling for preliminary exploration, the sub¬sequent development of ore body tonnages and grades and the establishment of mining parameters. The predominantly flat-lying mineralized formation is mined by room and pillar stoping. In an operating mine, jackhammer holer are drilled in backs and bottoms of stopes, and chip samples are taken for assay, concurrent with mining. Thus irregularities in ore bodies or nearby discontinuities are not overlooked which are above or below the general mine

Jan 1, 1971

By G. Brackebusch, S. J. Jung

Backfilling techniques are widely used in large-scale underground mines. Massive pillars, which have been left in place for stability, limit mining activity. Backfilling allows safe recovery of the ore remaining in pillars and assures long term stability. In deep mines expected high stress can be relieved with the backfill. Initially, waste rock was used to fill the openings with mixed results. The need to improve safety and reduce costs has prompted the industry to investigate alternatives. Hydraulic filling with Portland cement added has shown considerable promise, but little has been done to define the parameters of design effective system. The purpose of this study is to determine the relationship between backfill and mining components that can be used to effectively design a best-case hydraulic backfill.

Jan 1, 2000

By Mark H. Johns

Leaching of waste material at Kennecott's Chino Mines Division at Santa Rita, New Mexico, has been accompanied by increasing difficulty in circulating leach solutions through the dumps. As a means of recognizing existing problems and considering alternative applications of the leaching concept, a leaching research program was proposed which could be applied to a specific, typical waste dump. Conclusions derived from the area could then be applied to other leaching areas at Chino. Associated with the program was an evaluation of the physical characteristics of the area using Chino's drilling and radiation logging techniques.

Jan 1, 1970

By Harry M. Conger

Good afternoon, fellow members of the international mining community. I appreciate the opportunity to participate in this special three-day, international gathering, and to join with you in honoring one of my very good friends, Doug Fuerstenau. It couldn't be more fitting to have this kind of event to mark Doug's 60th birthday. You know, in addition to his faculty position at the University of California in Berkeley, Doug is a member of the Board of Directors of our Homestake Mining Company. So it is a double pleasure for me to help pay tribute to one of the outstanding academicians of the mining industry as well as a man with whom I work closely in running Homestake. I have been asked to talk about "The Future of Precious Metals," but I will concentrate my remarks on gold. Since the theme of this Symposium is "Challenges in Mineral Processing," what I'm going to talk about is a challenge that relates especially to a major problem faced by those of us who process ores to recover gold. I noted that in the Scope of this Symposium, it stated: "the mineral industry is currently facing many challenges to improve the economics, operating efficiencies and environmental concerns of the mineral processing system." I couldn't agree more with that statement. I think that a need exists for us to address this situation as it involves gold. And who better to consider this than the worldwide leaders of mineral processing research here assembled. I start with the premise that we need a new method for cyanide use or a chemical to replace sodium cyanide entirely. In the case of using cyanide differently, I see a continuing difficulty in getting general public acceptance regardless of how

Jan 1, 1989

By Harlan N. Barton

A commercially available portable X-ray spectrograph, lightweight and of rugged construction for vehicle or field camp use, was used for the determination of Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geo- chemical samples. Investigations showed a relative standard deviation of 1-3 percent, detection limits of approximately 100 ppm; and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic- absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1980

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global platetectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20o in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed

Jan 1, 1999

By Donald W. Breck

Zeolites were first recognized as a new group of minerals by Cronstedt with the discovery of stilbite in 1756. The word zeolite was coined from the two Greek words meaning "to boil" and "a stone" because of the loss of water when heated in the mineralogist's blow pipe. (1) In 1845 it was discovered that certain soils have the power of retaining ammonium Salts. (2) These were the first ion exchange experiments. Later it was discovered that it was the hydrated silicates in the soil that produced this phenomenon and several years later a paper was published dealing with the action of dilute salt solutions on silicates which showed that this base exchange principal, which we now call cation exchange, is reversible. The quantitative cation exchange behavior of zeolite minerals, such as chabazite, was studied. As a result any aluminosilicate which exhibited the property of ion exchange was referred to as a "zeolite;" even today the term has been applied to clay minerals as well as synthetic organic ion exchange resins.

Jan 1, 1973

By H. Suharyono, M. Lutsky, R. Hogg

Sediment consolidation in highly flocculated suspensions occurs only if the self-weight of the material exceeds its compressive yield stress. A simple model for sediment densification is presented and applied to the simulation of thickener operations. Measured relationships between sediment self-weight and the extent of consolidation are used to establish underflow densities. Supernatant turbidity data provide the information necessary to predict overflow clarity. It is shown that thickener depth can play a role in determining solids-handling capacity as well as dewatering performance. The application of the model to the design and operation of full-scale thickeners is described.

Jan 1, 1995

By Harry E. Holzschuh

The two Agrico Chemical Company self unloading Phosphate Rock barges put into service in 1976 operate at over their design carrying capacity. Each barge now carries 26,000 short ton instead of the planned 25,000 short ton at 32 foot of draft. They are in service between Agrico's Tampa, Florida Terminal and the Donaldsonville, Louisiana Fertilizer Complex, moving a total of 2,500,000 short tons each year. This was the first use of the Parascrew design for a marine application. The barges, with their 3,000 STPH unloading and matching loading rate is the vital link in this total transportation and handling system. Rock is moved from the Pierce, Florida Mines through the Tampa Big Bend Terminal, across the Gulf of Mexico, and up the Mississippi to the Agrico Faustina Phosphoric Acid Plant 30 miles below Bacon Rouge, Louisiana. The trip from the terminal to the plant is 600 miles and the turnaround time is just about six days. Seven years operating experience has proved that the system works. Fittingly, the two barges are named the "Faustina" and the "Pierce". They have a beam of 85-feet and are 495 feet long. folded depth is 43 feet, with a ballasted light draft of 19 feet and a typical loaded draft of 32 feet. There are four separated holds with the machinery room located forward of 101 hold. Each hold is 51 feet wide at the coamings with an 18 foot straight section on the side, and a 24 foot long, 600 slope sheet for a 23 foot clear reclaim width at the bottom. The Parascrew in each of the holds is 37 feet long between the bearings and is supported on a 14 inch diameter hollow shaft. The screw pitch varies and the diameter of the flights step up from l'-9" diameter to 2'-6" diameter on the discharge end. By sloping the centerline, a minimum four inch bottom clearance is maintained across the hold. Some bending of the tube does take place.

Jan 1, 1983

By M. J. Hughes

Kaiser Steel Corporation's Eagle Mountain operations are located in Southern California at a distance of about 130 miles east of the Corporation's steel plant at Fontana, California, and at a distance of about 225 miles from the nearest harbors which are located at Long Beach and Los Angeles, California Although the Eagle Mountain ore bodies are strategically located with respect to the steel plant and the harbor facilities, they are not of a very high grade and 'the geologic nature of the deposit makes it very difficult to mine and to concentrate. The iron ores occur as partial replacement of older zones mainly within dolomites and to a lesser extent within quartzites and quartz monzonites. The alteration was extremely variable and generally resulted in the formation of pyritic magnetic which, in part of the ore body, was leached to remove the pyrite and change the magnetite to hematite. Although the overall ore body is large, a major portion of it contains sulfur in the range of 1.0% to 5.0%. Obviously, this is too high a sulfur content for direct use in blast furnace feed.

Jan 1, 1968

By Lewis V. Wade

This paper summarizes the results of the rock mechanics monitoring program performed as part of Old Ben Coal Company's longwall coal mining demonstration project conducted in cooperation with the United States Bureau of Mines. The work described herein included installation of instruments, collection of data and data analysis performed during mining of the first longwall panel in Mine No. 24. The rock mechanics monitoring program included both surface and underground instrumentation and was designed to achieve the following purposes: 1 -To provide the capability to observe unusual situations during mining so that remedial measures could be instituted quickly 2 -To formulate design guidelines for future longwall mining efforts; 3 -To evaluate surface subsidence, and its character, rate and potential effects on cultural features, and to develop criteria to assist in predicting subsidence for other mines having similar roof conditions. Six previous attempts with longwall methods in Old Ben Coal Company's Hine 21 had been unsuccessful due to roof control problems. A description of these attempts is given by Moroni (1973). In preparation for the present longwall operation a study was performed to review existing data on the previous unsuccessful attempts, to establish coa1-and floor-strata bearing capacities in Mines Nos. 21 and

Jan 1, 1977

By Li Jiuping, Zhong Gang, Chen Yong Zhang, I. Michael Gowring

The Liaoning Dahuofang Reservoir Water Transfer Project is an important development for the Department of Water Resources of Liaoning Province in northeastern China. The 85.3 km water conduit will transport water from the Hun River downstream of the Huanren Reservoir to the outlet on the Suzi River leading to the Dahuofang Reservoir. The additional water is required to sustain the growing cities of Fushun, Shen-yang, Liaoyang, Anshan, Panjin and Yingkou. The project is divided into seven contracts. Three TBM contracts comprise almost 75% of the work and the others are drill and shoot. The focus of this paper is about the creditable TBM performances achieved and some of the problems encountered by Chinese contractors; notably two having had no previous TBM experience.

Jan 1, 2007

By Steven L. Webb

In 1965, Monsanto started planning of a new dike (No. 15) for use in disposing of ore tailings at its Columbia, Tennessee phosphorus plant. Generally, in the phosphorus industry only clay tailings are produced making it necessary to borrow fill for construction of a retaining dike. Borrow area investigations indicated that weathered shales and limestones adjacent to the dam site would provide adequate construction materials. It was proposed that the more clayey weathered shales would be used for the impervious core and the more granular weathered limestones would be placed in the outer shell of the dike. A dike section is shown in Figure 1 with gradation curves for core and shell materials in Figure 2. Figure 3 shows an aerial view of the tailings pond and dike during first-stage construction. Although the borrow area explorations indicated that the weathering of the sedimen-tary deposits was highly irregular, it was not considered necessary, at the time, to specify special excavation techniques that would ensure a thorough blending of the materials in the borrow pit. Instead, because of the short haul distance, a scraper operation for both clay core and granular shell materials was adopted as the most economical construction method. Using this materials-handling technique, variations in permeability could be expected in the compacted layers inthe embankment. Where continuous layers of less clayey limestones were placed in the core of the dam, extending from the upstream to downstream shells, seepage losses would be expected to increase substantially. Upon completion of the damn 1966, and shortly after reservoir filling, it was apparent that the construction technique used had resulted in the formation of pervious layers through the clay core. Excessive seepage on the downstream face of the dike was noticeable within a very short time. A monitoring program was established, using piezometric observations and flow measurements. These data indicated that seepage should be reduced and the application of an asphaltic emulsion

Jan 1, 1971

By Seal. Thom

Large heap leach operations around the world contain significant under-leached metal values that present recovery challenges to operators. The first challenge is to find the location of the highest inventory. High resolution resistivity ? has proven sensitive enough to detect such zones in the interior of heap leach pads to target treatment or re-leaching. Newmont Mining Corp. has adapted the high pressure fracturing technology, used in oil wells to stimulate select zones in heap leach pads to add reagents in 3-D for re-leaching, changing zonal chemistry for improved recovery and heap closure. High Resolution Resistivity ? is able to subsequently monitor injected solution flow and determine directional permeability during Hydro-Jex stimulation. The combination of these technologies has shown strong economic success, for selecting targets in the heaps and monitoring solution application. These technologies are now available to the mining industry for adoption.

Jan 1, 2008