Search Documents

By P. Semberg, B. Bjorkman, C. Andersson

"In this study, the interaction between magnetite and the additive olivine was studied after oxidation as well as after isothermal reduction at temperatures in the 500º-1,300º C range. In the olivine sample, the forsteritic olivine particles react partly during the oxidation pretreatment to form magnesioferrite and vitreous silica along the particle corona. This breakdown of the olivine particles during oxidation liberates magnesium from the particles, which do not react until temperatures of above 1,150° C in reducing atmosphere. When the hematite in the sample is reduced, and when the temperature is high enough to allow solid-state diffusion at ~800º C, the magnesium of the magnesioferrite redistributes, so that the magnesium concentration approaches the same level throughout the iron oxide structure. For magnetite, this did not occur until 800° C. At 1,000° C, this magnesium reacts further with the silica in the glassy slag phase, which crystallizes into fayalitic olivine. At this temperature, the magnesium has diffused over distances of more than 600 µm from large olivine particles after 2 hrs reduction. From this point, the primary slag phase in the pellet, until melting, is solid fayalite. Upon reduction to metal, the metallization front concentrates the MgO in the remaining wustite, which can lead to MgO levels of up to 10 mole% locally. The melting point of the fayalite is raised from 1,145º C to a melting range of 1,238-1,264º C due to the MgO increase, as estimated based on phase diagrams, which were adapted to the pellets tested. Much of the olivine that remained unaltered in the oxidation process will be encapsulated by iron before the particles begin to dissolve in reducing conditions and, therefore, plays no role in the reduction before final melting of the particles occurs.IntroductionEnvironmental concerns have placed increasing pressure on the CO2-intensive iron and steel industries to further optimize operation toward higher productivity and more efficient use of reducing agents. At the same time, high demand for iron ore has caused new iron ores with lower grades and more complex chemistries to be taken into production. In Scandinavia, the main iron-bearing material is magnetite-based pellets with olivine, which allow operation with very low slag volumes and, hence, lower fuel rate ( Slagnes and Sundqvist Ökvist, 2008; Hallin et al., 1994). Both the MgO and SiO2 of the olivine, as well as the elements of the gangue of the ore, i.e., Si, Mg, Ca, Al and alkali, interact with the iron oxides to give the finished pellet product its final properties in the blast furnace. Tailoring the additive mix to be used for a certain iron ore for optimal product properties, therefore, requires detailed knowledge of the mechanisms by which these elements dissolve and react in the pellet."

Jan 1, 2015

By K. Konialis

In the last twenty years, the mining industry has made marked efforts to improve its reputation in regard to its social performance. These efforts have been expressed in the 9th ICMM (International Council on Mining and Metals) principle as a commitment to contribute to the social, economic and institutional development of the local communities. Towards this goal, which has been increasingly highlighted because of its importance for sustainable development, a number of practices and methods have been developed. The international development literature describing these practices is full of so-called development buzzwords, such as stake-holder participation, empowerment, capacity building. This paper argues that none of these development catchwords are neutral, but contain assumptions based on a specific view of development. Since capacity building is a central task in development, the paper focuses on this concept and takes a critical look at the assumptions that underlie this concept and influence strategies employed by the mineral sector. It suggests that the notion of capacity building in some earlier approaches implies a set of asymmetric power relationships between developed and developing countries where capacity is transferred from the developed countries to the developing ones. The developing countries are seen as passive recipients while the experts, i.e. the developed countries through their mining companies ultimately control the capacity-building process. The paper also points out that the mainstream capacity development approach has been based on the assumption that local or indigenous communities are mainly made up of needs and capacity gaps. The goal of development projects should then be to address these needs, which are perceived and prioritized by the ?experts?. Critiques of this development model suggest that in order for the mining industry to embrace more successful and sustainable practices, it should rethink the notion of capacity building. It should move towards alternative approaches that see it as a two-way learning process which will serve to enhance not only the capacities of the communities, but also of the development practitioners and which will build on the strengths of the community, and move away from attitudes of superiority and practices of dependence.

Jan 1, 2007

By Hemendra N. Kalia

To plan a safe and efficient coal mining operation, the design engineer should use all the available information regarding the property to be exploited. The reliability of the mining operation must be as high as possible so that the plants relying on the coal can operate at the maximum design capacity. A good design should incorporate all of the known geological characteristics of the deposit, the structural and physical properties of the coal, as well as the rock which will form the roof and floor of the mine openings. A systematic method is proposed as a guide to insure a mine design that will be safe, efficient and will minimize surface disturbances resulting from mining operations. It is anticipated that the method proposed will result in maximum extraction at perhaps minimum cost to the operator. In general, to develop a mining area, several factors are systematically reviewed: (1) determination of the economic minability of the deposit, (2) the computation of the coal reserves, (3) the marketability of the coal, and (4) the life of the property. In general, boreholes are drilled in a predetermined pattern and geophysical or geological methods are used to log the boreholes. The information so obtained is primarily used to determine the quality and the extent of the deposit and to determine to some extent such geological features as faults, barren areas, washouts, and channels.

Jan 1, 1973

By Walter H. Schwedes

Ore grinding mills are really just slowly rotating barrels, but barrels that are growing in size so fast that the application of electric drives for them is rapidly approaching a technology like that for wind tunnels or pumped storage drives. This application is particularly worthy of care because some 40% of the 75 megawatts of power used by a large copper ore concentrator, or some 60% of the 200 megawatts supplied to a large iron ore concentrator, are for grinding. These ore plants are located where the ore is, not where a utility happens to be. So, the challenge is not only to choose a drive and .power transmission for reasonable cost, high performance, reliability and minimum maintenance, but to afford the interface between mill drive and power distribution and source systems to minimize the whole ore plant's monthly power bill, or costs of self generation. Conclusions can be reached in optimizing a drive selection only for each particular ore plant's set of parameters, but by identifying the criteria for selection and then weighting each type of drive per criteria, yardsticks for final choice become apparent. This is the purpose of this paper. Grinding action takes place inside the barrel, where the ore charge is ground with the aid of balls, or mill length rods, or large chunks of ore as in autogenous grinding.

Jan 1, 1972

By D. M. Urich

This paper is a follow-up on a previous paper presented at the A.I.M.E. Meeting in Chicago, Illinois, on February 17, 1965, by Mr. D. Kelly Campbell. Mr. Campbell's paper was presented prior to the operation of the Eveleth Taconite-Company's Plant, and this paper outlines and reports on the operation and performance of the Plant after the first nineteen months of operation.

Jan 1, 1967

By Robert Roggenthen

In 1994, ASARCO's Mission Complex Mine Planning Department designed a new stripping schedule to take advantage of reserve opportunities. Based upon the new stripping design, overburden removal exceeded available hauling capacity. This increased hauling capacity requirement required that ASARCO consider alternative technologies for material transport. In 1997, ASARCO Mission Complex completed the purchase and installation of a 3.5 km, 8,600-tph conveyor system to transport waste material. The conveyor system is composed of two apron feeder/sizer units manufactured by Mining Machine Development LTD. and a conveyor system manufactured by Krupp-Robbins. This paper will review the option of truck haulage versus conveyor transport for overburden removal by (1) describing engineering studies contributing to the solution, (2) researching proactive options to create alternative management decisions, and (3) revealing final results of the project.

Jan 1, 1998

By F. M. Doyle, Jun Li, Milton E. Wadsworth, E. Peters

The Raman spectroscopic technique was used to study electrochernically oxidized pyrite in-situ. It was found that Raman-active sulfur oxidation products could be detected after a proper potential was applied to the pyrite electrode for a threshold period of time. There existed a minimum potential below which sulfur could not be observed. However, when the applied potential exceeded a certain limit, the intensity of the sulfur spectra decreased. The minimum potential at which sulfur could be observed changed with solution pH. For both acid (pH 2.7) and weak alkaline (pH 9.2) solutions, the minimum potential was 0.8 V/SCE, whereas for neutral (pH 6.5) solutions the value was 0.4 V/SCE. In strong alkaline solutions (pH 12.5) surface sulfur oxidation products could not be detected at any potential.

Jan 1, 1993

By Kim Lapakko

As part of a project funded by the US EPA, through the Western Governors' Association, the recent literature on the prediction of acid drainage from metal mine wastes was reviewed. Static tests such as Acid Base Accounting, Modified Acid Base Accounting, B. C. Research Initial Test, and APP:S Test attempt to quantify the total capacities for a mine waste to produce and consume acid. In kinetic tests (e.g. humidity cells, soxhlet extraction, elevated temperature oxidation, column tests, batch reactor tests, B. C. Research Confirmation Test) mine waste samples are subjected to oxidation and the resultant drainage pH is assumed to reflect that of mine wastes dissolving in the field. This paper summarizes information presented in the recent literature on static tests.

Jan 1, 1992

By Harold J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The scooptram that is used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine the effect of exhaust pipe location and time spent out of the drift, as well as to determine if a relationship existed between CO2 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that has the capability of predicting changes in source strength as well as source location. It was also determined that four relevant factors include effective heading height, apparent longitudinal diffusion coefficient, transverse concentration gradient at the face, and average dispersion width of the exhaust jet. As these factors change with heading geometry and ventilation configuration, they were determined experimentally, Carbon dioxide was used as a tracer to calibrate the model; since, knowing the fuel flow rate, it is possible to calculate CO2 production. The above four factors in the computer model were calculated using a regression analysis, comparing predicted local concentrations to measured local concentrations. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field. A parametric analysis shows that the exhaust pipe location can have a significant impact on operator exposure to exhaust gases. It was also shown that NO concentration varies directly with C02 levels. Predictions using the dynamic model are contrasted with constant source strength (pollutant flow rate) results. An analysis of these predictions for computing time-weighted average NO shows the dynamic model predictions of operator exposure to this pollutant to be less than one-half of the value predicted using a constant source model.

Jan 1, 1981

By Robert E. Ennis

Several important economic variables must be studied when planning a major underground conveyor haulage system if the objective of tow cost haulage is to be met. The purpose of this paper is to call these economic factors to the attention of the mine planner and encourage their serious consideration. To illustrate, the importance that some of these variables hole for the mine operator who wishes to reduce costs and maintain sound belt haulage practice, these areas of discussion will be covered. 1. Selection of economical flite lengths. 2. Economics of wire rope frame vs. rigid frame conveyors. 3. How idler design affects conveyor costs. 4. Economies in drive design. 5. How speed affects conveyor cost. 6. P.V.C. vs. Neoprene belt - what savings? 7. Maintaining, conveyor investment through maintenance. 8. Miscellaneous factors affecting the cost of belt haulage.

Jan 1, 1967

By Rick Wright, Gregory L. Raines

San Diego’s need to access underground space has dictated a long history of tunnel construction. The subsequent need for water, coupled with San Diego’s natural attractiveness, has led to significant population increases and the need for the construction of even more tunnels. This paper will provide a historical summary of the progression of mines, tunnels and trenchless technology construction projects that contributed to the advance of current technology, feasibility, and constructability. A bibliography of relevant reports and data is included.

Jan 1, 2001

By M. Misra

It is estimated that the volume of low -level and intermediate level contaminants present in the soil at different DOE sites is of the order of several million cubic feet. The existing remediation scheme is containerization followed by burial in Land Disposal Facilities (LDF's) which is economically unattractive warranting the need to develop alternate remediation routes. One such route is the physical separation based volume reduction approach to removing a MINIMUM AMOUNT OF CLEAN SOIL with the radioactive particles, reducing the amount of material that requires disposal. The purpose of this study was to evaluate and test the feasibility of using physical beneficiation techniques for removal of contaminants from soil. The performance criterion was to recover at least 80% of the activity in 20% or less of the original contaminated soil volume. Four different radioactively contaminated (primarily uranium and plutonium) soils from DoE sites namely LANL, INEL, Fernald Plant 1 Storage Pad (ID-B) and Mound soils were tested using gravity, magnetic, gravo-magnetic, hydrocyclonic and flotation devices. The paper is divided into the two sections. The first section presents the overview of the Heavy Metals in Contaminated Soil Treatability Project conducted at the University of Nevada, Reno (UNR) describing the salient features of a state-of-the art Soil Washing Laboratory and the technology equipments used in the test program. The second section describes the soil characterization and typical volume reduction results obtained from the UNR tests. Among the physical separation processes, only flotation processes passed the performance criterion. For the LANL and INEL soils where the contamination was contained in coarse particle size, it was possible to recover more than 80% of the activity in less than 10-20% of the original volume of the soil thus rendering 80-90% of the soil "clean". For Fernald and Mound soils where contamination was of colloidal nature, flotation based processes showed encouraging results and are recommended for further studies.

Jan 1, 1995

By Lane White

Ninety-seven papers were presented at the Mine Ventilation Symposium's technical sessions. Following are brief summaries of topics covered in this wide-ranging program.

Jan 1, 1993

By D. Gu, B. Lin

Shaft drilling is one of the most useful methods of driving shafts. This paper describes the application and development of the technique in coal mine construction in China.

Jan 1, 1994

By Louis I. Briggs

Evaporite rocks, salts of the more soluble ions in seawater, are deposited when seawater becomes concentrated by excess evaporation in marginal basins having restricted circulation with the open sea. The simple conceptual model of an evaporite basin (Figure 1) has a single inlet connecting the basin to the open ocean, the restriction to open circulation being caused by a bar or reef near the mouth of the inlet. As the oceanic water flows from the inlet into the basin it tends to form a thin layer of brine that spreads out over the surface of the basin brine, and as it does so, the salt concentration In the surface layer gradually increases owing to continued evaporation of the water. When the solubility products of the salts in the surface layer are exceeded, the salts precipitate and settle to the bottom of the basin, The order of precipitation follows their order of least solubility. Normally the carbonates separate first, followed by the sulfates and chlorides and the more complex double salts. In nature there is considerable overlap in their ranges of precipitation. The water flow in the basin, also shown schematically in Figure 1, diverges from the inlet essentially perpendicular to the lines of' equal salinity in the surface brine. The distribution of salts deposited in such a model will parallel the isosalinity lines, being arcuate and concave toward the inlet (1)

Jan 1, 1967

By J. Chae, D. Pecha, R. Andrews

The Henderson/ML King CSO Project is a major combined sewer overflow (CSO)reduction project for the Department of Natural Resources and Parks of King County, Washington. The central element of the project is the 3100 lineal feet long, 14'-8"diameter 42nd Ave S Storage/Treatment Tunnel. During the course of the project, the owner and consultants evaluated numerous elements of the tunnel including the alignment, geotechnical conditions, tunnel liner, and settlement monitoring requirements. The contractor utilized innovative shaft construction methods for the tunnel portals, and adhered to strict contract requirements in successfully constructing the tunnel. This paper provides an overview of the design and construction elements of the 42nd Ave S Storage/Treatment Tunnel that led to the successful completion of the project.

Jan 1, 2005

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania. West Virginia, Kentucky and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought but rather 200 in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Feb 24, 1997

By J. Philip Bromberg

The 1977 Clean Air Act Amendments will have a large effect on the coal-fired segment of the electric utility industry. Since electric power generation constitutes by far the largest single use for coal, this legislation has the potential to greatly affect future patterns of coal utilization in the U.S.A. The inability to depend exclusively upon low sulfur coal as an exclusive mode of compliance with New Source Performance Standards may greatly lessen projected demands for low sulfur coal by eastern utility boilers. The requirements of the legislation is discussed with particular reference to the needs of the electric generating industry, along with the technologies available for complying with the Act.

Jan 1, 1978

By John H. Bassarear

The never ending search for lower unit costs led Pima Mining Company's management to study various alternatives shortly after Expansion III was completed. It soon became apparent that a considerable amount of ore assaying 0.35% copper had to be moved in order to maintain mill feed at the desired 0.54% copper content, which is the overall grade of the ore reserves. Detailed investigations revealed that for a period of 8 - 10 years, about 14,000 tons per day of 0.30 - 0.40% copper ore would pass by the crusher en-route to the low grade stockpile. This ore is very hard, very clean and has to be mined at a relatively uniform rate. A six month pilot plant run testing autogenous and semi-autogenous grinding gave very encouraging results. Since no mining costs need to be charged to the extra tonnage (it had to be mined anyway) the only major costs would be against milling. The decision to proceed was made in August 1970 and Fluor-Utah was retained as the prime design construction contractor. Ore was first put through the new mill on December 29, 1971. By March of 1972 design tonnage of 14,000 TPD had been attained. The first three expansions at Pima Mining Company, 20 miles south of Tucson, increased mill capacity from 3,000 TPD to 36,000 TPD. These expansions included a separate, conventional, three stage crushing plant plus additions to the existing concentrator that primarily duplicated the then current flowsheet. Expansion IV, however, consisted of an entirely new and separate primary crusher and a completely new mill building located about 2,000 feet southeast of the 01 d concentrator. The new mill, using semi-autogenous grinding, produces scavenger and rougher flotation concentrates that are pumped to the old mill for regrinding, cleaning, thickening and filtration.

Jan 1, 1973

By Howard V. Sears

Prospecting in its modern context means simply the gathering of information on which, to base plans for the utilization of our mineral resources. One prospecting system familiar to T. V. viewers is the pan of the old gold prospector which, while he prospected, could produce the wealth which financed him in his search. Present day geophysical "prospecting" systems, which are based on the real or supposed responses of an ore specimen, to various stimuli finder controlled laboratory conditions, are promoted as means of reducing the cost of prospecting. The universal drawback to all geophysical systems is that they yield "soft" data which are only presumed to be analogous to ore mineralization until they can be calibrated, by conventional prospecting systems, to each actual mineral environment being tested. By this time the system usually is no longer cheap. Since the raw data are too esoteric to be used until interpreted by geophysicists, usually in the light of their own personal theories and experience, the certainty of multiple interpretation is introduced. The concept of prospecting, at St. Joe Minerals Corporation's Viburnum, Fletcher and Brushy Creek mines in the new Missouri Lead Belt, encompasses surface diamond drilling for preliminary exploration, the sub¬sequent development of ore body tonnages and grades and the establishment of mining parameters. The predominantly flat-lying mineralized formation is mined by room and pillar stoping. In an operating mine, jackhammer holer are drilled in backs and bottoms of stopes, and chip samples are taken for assay, concurrent with mining. Thus irregularities in ore bodies or nearby discontinuities are not overlooked which are above or below the general mine

Jan 1, 1971