Search Documents

By Robert L. Runkel, Kenneth E. Bencala, Briant A. Kimball

Thousands of abandoned and inactive mines are located in environmentally sensitive mountain watersheds. Cost-effective remediation of mining sites in these watersheds requires knowledge of the most significant sources of metals to surface waters. The significance of a given source not only depends upon the concentrations of a toxic metal, but also on the total mass, or load of metal added to the stream. To determine loads, we combined tracer-injection methods, to provide reliable discharge measurements on a watershed scale, with synoptic sampling, to provide spatially detailed concentration data. The resulting load profiles indicate which sources have the greatest effect on streams, where natural attenuation of metal loads occurs, and where ground-water inflows are located. This is part of the information needed for planning remediation of mine-drainage effects. The approach is illustrated by comparing zinc loading curves from three watersheds affected by mine drainage.

Jan 1, 2000

By Walter Shukin, Mark T. Olsen

An enormous quantity of tailings to be ultimately stored, unfavorable topography, severe climatic conditions, and an environmentally offensive red effluent all contributed to the challenge of designing an effective and cost efficient tailings confinement program at the open-pit iron ore mine operated by Quebec Cartier Mining Co. at Mount Wright in northeastern Quebec. The mine has been operating since 1976, but a detailed disposal plan was first initiated with construction of some channels and ditches during 1980. In the coming years, a system of dams, channels, and tailings confinement dikes will be constructed to accommodate tailings produced in the next 25 years. Careful consideration has been given to environmental effects, and the works under construction have been sized and situated to be extended as required to an ultimate mine life of 87 years.

Jan 8, 1981

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The forestry reclamation approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22 m (4 ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes (i.e., greater than 23°) could lead to slope failures, which is one of the issues that the Surface Mining Control and Reclamation Act of 1977 (SMCRA) sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. During this first phase of investigation, there has been no major mass movement of the slope and slope stability analysis indicates that the application of the FRA has little impact on the overall stability of the slope. Mining Engineering, 2011, Vol. 63, No. 12, pp. 55-62. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Michael R. Grubbs

In most resource recovery plants the incoming solid waste material is first shredded and then air classified into a light and a heavy fraction. The light fraction which contains mostly paper, cardboard, etc., can be used either as a fuel for power generation or in the production of new paper products. The heavy fraction which remains consists mostly of glass, ceramics, wood, ferrous metals and non-ferrous metals. The ferrous metals may be removed from the heavy fraction by conventional magnetic separators. After primary shredding, most of the glass and ceramic is fine in size and may be screened away leaving a residue of wood, cardboard, and non-ferrous metals. This residual heavy fraction is the input material for the separator described in the present paper. A new metal separator was recently reported by t. Schlömann1. The author described the theoretical relationships and presented results of tests on samples of the residual fraction of municipal solid waste. This paper describes the operation of the metal separator and develops the basic separation relationships controlling the process.

Jan 1, 1976

By Felicia F. Peng, Lili Li

The dispersion model of nonideal flow was applied to describe the hydrodynamic state within the flotation column. Residence time distribution (RTD) data of a laboratory flotation column were measured to determine the parameters of the model. The effects of operating variables and column geometry on the Peclet number which reflects the extent of axial dispersion were investigated and a semi-empirical expression of Pe was formulated. The dispersion model was validated for the column flotation of ultrafines coal. Under the conditions of sufficient aeration rate and frother addition, a good agreement between the measured recoveries and predicted data was obtained. The dispersion model with first-order flotation rate process of the flotation column developed in this study is useful in predicting the collection zone recovery of fine coal, and for the flotation column scale-up.

Jan 1, 1995

By Richard J. Ebens

The trace element geochemistry of the cherty, clay-rich carbonate residuum. Covering much of southern Missouri and adjacent parts of Arkansas was investigated during the early 1970's as part of a statewide geochemical survey of Missouri-1/2/3 The study was environmentally oriented and focused on the character of the "natural' geochemical environment of the state. A great deal of effort was made to collect samples that would represent the geochemical variability of the near-surface environment in an unbiased way. In general, this was accomplished by use of randomization procedures in both collection and analysis. Most of the sampling sites were selected randomly to prevent personal bias from entering into sample selection. In the laboratory, samples were analyzed in a randomized sequence to circumvent the effects of any systematic bias that may have entered into the laboratory procedures. Several residuum samples contained 1 000 parts per million (ppm) or more of Pb, Zn and Ba. All these samples were collected in Washington County in or near the barite district. The frequency distributions shown in figure 1 indicate just how unusual the residuum in Washington County is with regard to these three metals and copper. The shaded parts of the histograms represent the samples from Washington County. The histograms are based on analyses of 141 samples from 38 localities scattered over the subcrop of the Cambrian and Ordovician Formations of southern Missouri and northern Arkansas. Eight localities were selected randomly from over each of four bedrock units--Bonneterre Dolomite, Potosi and Eminence Dolomites, Roubidoux Formation, and the Jefferson City, Powell and Cotter Dolomites. Six localities were selected randomly from over the Gasconade Dolomite. The geochemical "background" for these elements in residuum is defined by samples from outside of Washington County (unshaded part of the histogram); lognormal distribution curves have been fitted to the corresponding parts of each histogram. Clearly, these lognormal models (curves) describe well the background

Jan 1, 1977

By John F. Bryce, Fazley A. Azhar

With increasing economic pressures to produce more with less, the material handling industry is turning to engineered solutions to reduce the number of people required to operate its facilities, monitor maintenance trends, pin point problems, increase throughput, decrease downtime, identify weak links in the production system, and increase times between scheduled maintenance. One solution to these problems is to implement a Total Control Solution (TCS) using industrial computers, fieldbus networks, and distributive Input/Output (I/O) for control, automation, data acquisition, and analysis. This paper will discuss some of the control fundamental principles used by Technisys, Inc. (TI) to implement TCS.

Jan 1, 1998

By Katzer R. Klimpel, J. Sewell

Dr. Roussey Roussev The use of chemical additives on grinding is of significant importance considering the high energy consumption of grinding processes. My research indicates that the dispersant approach explains the effects, in this particular case of wet grinding. Further, the dispersant approach combined with torque measurements give the possibility of clarifying the mechanisms involved when using grinding aids. I find the conclusions derived from the data obtained to be correct and useful for grinding. In general, I agree with the explanations. However, I would like to discuss several additional points that I consider to be important, and in the same time to mention some of my own results from investigations similar to those presented in the study under discussion. The "bed volume concept" and the change of slurry viscosity explain adequately the data plotted on fig. 3, in conjunction with Figs. 1 and 2. However, the significant increase of the average torque in the case of 83% solid with XFS-4272 introduces the necessity of establishing the optimum of percent solid when dispersant is used. For example, the optimum percent of solid for different materials varies. One of the reasons is the material's mass density. On the other hand, it is necessary to determine the concentration of the chemical used. Because of this, it would be interesting to know how the cited concentration was selected. The supportive discussion and verification by Dr. Roussev, with results similar to that of the paper, is appreciated. I will try to answer the additional questions he has raised. To begin with, the mill was fitted with six lifters of approximately one-quarter inch height. There has been extensive lab and plant level work to understand downstream influences of using dispersants like XFS-4272*. In sulfide ore processing, which is the area in which most industrial scale testing has been performed with this approach, neutral to positive influences have been observed. For example, positive effects (e.g., increased recovery) have been noticed in flotation operations involving ores that have a tendency to produce excessive slimes upon grinding. (1) Also, the use of a dispersant has been shown to demonstrate a positive influence on classification by improving the sharpness of separation and preventing a decrease in d50 value that usually accompanies increasing flow rates to classifiers.(2) The biggest potential downstream problem is in thickening, which at the dosages involved, has not been a problem in plant scale usage. The commercial price of dispersants like XFS-4272 is quite variable depending on source, concentration, etc, but a typical cost of XFS-4272 to achieve a 10% increase in throughput in industrial mills has been between 20 and 35- US per ton of feed ore (1981).

Jan 12, 1982

By Paul C. Jones

Summitville is an old mining district located south of Wolf Creek Pass in the southern San Juan Mountains of Colorado at an elevation higher than 3500 m (11,500 ft). The Summitville mine site is about 40 km (25 miles) southwest of Del Norte. The current mine, developed by Galactic Resources Ltd. and its subsidiaries in the mid-1980s, is on the north facing side of South Mountain. The area is drained by Cropsy Creek to the east and Wightman Fork to the north, both tributaries to the Alamosa River. Mining in the Summitville area began in 1870 when James Wightman discovered placer gold on what is now known as Wightman Fork of the Alamosa River. The first vein-type deposits were located in 1873 on South Mountain near the current Summitville Mine. Mining began in the district in 1875 and continued sporadically through 1942. Major mining episodes occurred from 1875 to 1894 and from 1926 to 1942. Total gold production from the mining district through 1949 totaled 7.5 t (240,000 oz). An additional 7.7 t (249,000 oz) were produced during Galactic's tenure. Natural degradation of the outcropping sulfide-rich veins in the area and the early mining activity, including development of the Reynolds, Dexter and Iowa drainage tunnels in the late 1890s, have polluted the streams draining the area with heavy metals and acidic water. Names of the various tributaries to Wightman Fork, such as Iron, Alum and Bitter Creek, testify to this natural pollution. This degradation has reduced, or killed, aquatic life in several area creeks, including Wightman Fork, for many years before recent mining activity.

Jan 1, 1993

By D. T. Kinard, A. A. Schweizer

An operational 9 meter (30-foot) high gold heap leach pile was investigated by excavating test pits up to 6 meters (20 feet) deep, obtaining bulk and relatively undisturbed thin wall drive samples, and observing the ore distribution patterns exposed in the test pit walls. The clayey ore is crushed, agglomerated with lime and cement, and deposited on the leach pads using a radial stacker. Laboratory tests performed included moisture-density, gradation, compaction, Atterberg limits, permeability (constant and falling head), and triaxial strength tests. Discussion is presented on the effects of agglomeration on the permeability and strength characteristics of the in-place ore. Also discussed is the effect of deposition of the ore using the radial stacker.

Jan 1, 1987

By Nancy Bingham

The mining industry’s image is molded by what the public knows, or thinks it knows about mining. As Caterpillar prepared for the production of its educational video, Common Ground, the public’s perceptions about mining needed to be established. Before we could educate people about mining, we had to find out what they already thought. As those perceptions were analyzed, we were able to narrow the video’s focus to relevant, realistic approaches. We found out what people did not know about mining. And, most importantly, facts they should know were singled out - facts that could create more favorable attitudes. This research was instrumental in the final direction of the Common Ground project. What the public believes As these perceptions about mining were researched, it was found that the beliefs of the general public are dominated by four concepts. Quotations from interviewees are included with the discussion of each of these concepts. Figure 1 shows an overview of people’s beliefs before education.

Jan 1, 1994

By Alfredo Menendez, Alberto Sarmentero

A B S T R A C T The Los Pijiguaos bauxite is one of the largest accumulations of trihydrate alumina ore recently discovered; it is a plateau type, with no overburden, relatively soft tertiary quartz-bearing bauxite developed on a pre-Cambrian Rapakivi Granite batholith. The deposits are found in the northwestern rim of the Guiana Shield, State of Bolivar, Venezuela, and were discovered in 1976 after a grass-roots exploration campaign. Target areas were mainly selected on the basis of geological and geo¬morpholigcal criteria, guided by correlation with known deposits elsewhere in the Guiana Shield. The vertical. lateritic profile consists of an upper concretionary zone, followed by a mottled zone, a palid zone and finally the weathered rock merging into fresh granite. The upper concretionary zone displays a cellular, pisolitic or spongy texture and contains the following minerals: gibbsite (60-90%),quartz (5-10%), hematite (5-10%), goethite (under 5%), boehmite (traces), kaolinite (traces). The gibbsite content decreases sharply downward from the lower limit of the concretionary zone and the kaolinite and quartz content increases in the underlying mottled zone. The mottled and palid zones display a pseudo rapakivi texture and quartz, kaolinite and mica are the. essential minerals.

Jan 1, 1984

By A. Ayoubian, V. Nasri

This Tunnel Connection project will include construction of two short tunnels to connect the existing subway tunnels (Red and Blue lines) in the northern loop area of downtown Chicago through a new station. The Southeast Tunnel will connect the Red Line to the new station below the intersection of State and Washington Streets and the Northwest Tunnel will connect the Blue Line to the new station below the intersection of Dearborn and Randolph Streets. The connection tunnels are located in a very dense urban area of downtown Chicago and under several important historical buildings. Both tunnels are curved at the intersections and located at a depth of about 7.5 m below ground surface in saturated soft clay with an average undrained shear strength of approximately 25 kPa. The design calls for minimizing surface disruption and ground displacement while maintaining normal operation of the existing subways during the construction of the connections tunnels. This paper presents mining and cut and cover tunneling alternatives for the project.

Jan 1, 2007

By Johann Engelbrecht, Stéfan de Bruyn, Petrus van den Heever

A system for the on-stream X-ray diffractometric determination of mineral phases in slurries was developed in response to the mining industry's need for process control during the beneficiation of industrial minerals. The instrumentation for and results from testwork conducted at a phosphate rock beneficiation plant in Florida are discussed. Results show that the concentrations of the minerals apatite (var. francolite) and quartz can be accurately determined every few minutes, so that adjustments to the flotation circuit can be timeously executed from the control room. The on-stream measurements can ultimately be integrated into an automated plant control strategy. Estimates of savings on reagent and staffing costs, as well as the benefits from consistent grades and greater recoveries, have shown that the investment in such a system could often be recovered in less than a year.

Jan 1, 1999

By R. S. C. Rogers

Semiautogenous milling was the subject of 18 papers presented at the SME Fall Meeting in Albuquerque, NM. The process design and scale-up of SAG mills was discussed in several papers. These included a review of testing methods for the sizing of SAG mills by Barrett and Allan. Austin et al. presented an improved simulation model for SAG mill grinding, with model validity demonstrated against pilot plant SAG mill test results. Rogovin et al. presented some pilot plant results relating to the charge motion, hold-up, and particle size segregation in SAG mills. A number of papers described improvements achieved in operating SAG mill circuits. These included presentations by Dailey concerning mills at the National Steel Pellet Co., by Brown and Pipke concerning the Island Copper grinding circuit, by Lovering of Afton Mines Ltd., and by Bartrum et al. of Kidston Gold Mines Ltd. Bush and Hegerle of Amax also discussed SAG mill operations at the company's Henderson mill. They addressed the topics of SAG mill grinding economics. Other papers addressed the topics of SAG mill control (Vanderbeek et al. and Pennington), grinding media (Meulendyke et al.), liners (Kjos), and fabrication (Carr and Utley). The 1985 AIME Annual Meeting in New York featured four technical sessions concerning size reduction technology and practice. Papers involving fundamentals included one by Hinde describing simulation model usage for quantifying the classification and concentration of heavy minerals in grinding circuits. Another, by Rogers et al., discussed simulation models that were used as a design aid in evaluating screens versus hydrocyclones for fine grinding circuits. Arbiter discussed dimensional considerations in grinding mill design, and Schwechten and Schonert proposed the use of a high pressure roll mill as a means for reducing energy requirements in fine grinding. Internal classification in tumbling mills was the subject of a paper by Hogg and Rogovin. The mechanism of internal classification were identified and their effects illustrated. Simulation for the process design of ball mills was exemplified in a paper by Rogers, Austin, and Brame concerning phosphate grinding in laboratory to large diameter mills. The incorporation of liberation into size reduction models was the subject of papers by Austin et al., Herbst et al., and Choi et al. Gupta used simulations models to further investigate zero order fines production in ball and rod mills. Of the published literature, many articles on size reduction were published in various publications in 1985. Articles concerning ball mill grinding included an analysis of interstitial gas effects in dry grinding by Cottaar et al., an analysis of mill grinding noise by Watson, studies of factors affecting breakage rates in dry milling by Gupta et al., and in wet milling by Tangsathitkuchai and Austin. Austin and Klimpel presented two papers concerning ball wear and ball size distribution effects. Koka et al., and Gotsis et al., described recent developments concerning the Szego mill. A model for hammer milling circuits was described in papers by Gotsis et al. and Gotsis and Austin. Heim et al. reported on wet grinding in Perl mills, and Kuga et al. presented findings concerning pulverizing in a screen mill. Studies of grinding effects on particle surfaces were published by Meloy and Hofmann et al., and Scieszka proposed a technique to investigate pulverizing properties of coals. Austin and Rogers discussed factors of powder technology of significance in industrial size reduction in mills and crushers. (Space limitations preclude listing of references. A complete list is available from author.)

Jan 5, 1986

By J. A. Herbst

Grinding circuits employed in mineral processing operations are designed to produce feed materials for beneficiation steps such as flotation and magnetic separation, which are sufficiently fine to achieve good liberation of valuable minerals from gangue without over- grinding. In many respects, grinding is the most important unit operation in a mineral processing plant. If adequate liberation is not achieved during grinding, subsequent separation steps will yield low metallurgical recoveries and/or product grades. Grinding energy requirements and operating costs typically exceed 50% of the total expenditures of the entire plant. Because grinding is an inherently energy intensive process and grinding circuit capital and operating costs are high, it is essential that such circuits be run as efficiently as possible. In- creased efficiency in grinding usually translates to a decrease in the energy required to produce a metric ton (short ton) of product size material. It is generally accepted in the mineral industry that efficient grinding circuit performance can not be achieved without the use of some form of automatic control. This is true because all circuits are subject to random disturbances which, if left unchecked, will upset circuit performance and rob a plant of productivity. Such disturbances arise from a variety of sources including natural variations in ore characteristics (particularly hardness changes), uncontrolled water additions, feed-rate upsets, changes in crusher performance, and mechanical upsets such as blockages in pumps and classifiers. Many of these disturbances occur with a frequency which is too high for an operator to detect and react to efficiently. Disturbances which occur on a time scale of several minutes up to several hours can be effectively dealt with using automatic control.

Jan 1, 1979

By R. Herrera-Urbina, D. W. Fuerstenau

A large number and a wide variety of chemical reagents are used in flotation processes for wettability and Eh control, particle agglomeration/dispersion and bubble stability. A historical account of the use of flotation reagents through the years since flotation was introduced as a viable and economic process for the concentration of sulfide minerals is given and a review of old and modern postulates of their interaction with minerals is presented. Although the results of surface and colloid chemistry studies with well characterized mineral/flotation reagent systems have advanced our understanding of the role played by these chemicals in the flotation process, many questions remain unanswered. Moreover, new flotation reagents are needed to solve the challenge posed by the treatment of problematic-type ores and fuel deposits that have increasingly become the source of our raw and energy materials. Because of the depletion of high-grade and relatively easy-to-process ores, flotation scientists and engineers are confronted with finding more specific and selective flotation chemicals to effectively and economically concentrate minerals. The development of new flotation reagents is vital for cleaning fine coal and processing polysulfide, polymetallic ores, and mixed oxide/sulfide ores.

Jan 1, 1989

By C. Ford, R. E. Salas Rojas, J. P. Contreras Rodriquez, S. A. Pierce

Heightened environmental consciousness has resulted in the development of various international accords dealing with natural resource management. This international awareness is now being translated into regional and local initiatives that proactively implement collaborative environmental management programs. One such program was recently initiated in northern Chile in recognition of the interconnection of Andean salars. Cooperative efforts between industry, governmental agencies and academic professionals have resulted in the implementation of simultaneous environmental monitoring of flora and fauna in the salars of northern Chile. This coordinated effort is leading to an improved understanding of the migratory patterns of South American fauna, as well as improved access to an expanded database for the multiple user groups associated with the Andean salars. The El Abra Mine is actively participating in these coordinated monitoring efforts.

Jan 1, 1999

By R. J. Hickson

From 1993 through 1999 Cyprus Amax Minerals Company successfully completed eight major construction projects around the world. Six greenfield mines were brought into production, an ongoing operation was completely modernized, and an environmental issue was appropriately remediated. The projects stretched over three continents, from arctic Russia to the Atacama Desert, from 16,000feet to sea level, from city suburbs to remote wilderness, from a low of $130 million to over $1 billion. Open pit and underground; mill and leach; gold, copper, molybdenum, and coal were all encompassed. The breadth of diversity experience from these projects inspired Cyprus Amax to create a “best practices” project management protocol, to steer corporate expansion into the next millenium. This paper summarizes those best practices, while high-lighting project management pitfalls to avoid.

Jan 1, 2000

By R. A. Pyper

Laboratory leaching experiments were conducted to ascertain the effectiveness of acidic solutions of thiourea, CS(NH2)2, for dissolving gold from finely disseminated gold ores. The ore tested was from the Chipmunk orebody of the Northumberland mining district in Nye County, Nevada, USA. Extractions of up to 90 percent were attained from the ore. Extraction was shown to be dependent on thiourea concentration, ferric sulfate oxidant concentration, acid concentration, and leaching time. Optimum conditions were an ambient temperature leach near pH 1.0 utilizing 100-200 kg/t thiourea and 50 kg/t ferric sulfate for 8 to 24 hours.

Jan 1, 1981