Search Documents

By Gerrit V. R. Goodman, Charles D. Taylor

A technique was developed to determine the fraction of air recirculated from the scrubber exhaust toward the face and the fraction of gas captured by the scrubber. To determine these two values, a series of tests was required. In the first test, gas was released at the face area and concentrations measured at the scrubber exhaust. In the second test, gas was released directly into the scrubber with concentrations again measured in the scrubber exhaust. The simultaneous solution of two independent flow expressions gave values of recirculation and scrubber capture. A series of tests was conducted with various combinations of scrubber flow, curtain flow, setback distance, and machine location. Statistical analyses then were conducted to determine those factors which influenced the levels of scrubber recirculation and scrubber capture in a deep cut. INTRODUCTION As cutting depths increase, the trend is toward the use of blowing face ventilation systems. With these ventilation systems, the potential exists for recirculation between the scrubber exhaust and the intake air stream. One concern is that methane gas, having been removed from the face area, is subsequently recirculated back into the intake airflow. Under these conditions, methane-laden air could be substituted for fresh intake air, leading to increased methane concentrations at the face. There is currently no standard for recirculation between the scrubber and intake airflows. The implied understanding of the Mine Safety and Health Administration (MSHA) is, and has always been, that any recirculation of ventilation air is unacceptable. To minimize recirculation potential, MSHA suggests that operators maintain scrubber and curtain flows within 0.47 m3/sec (1000 cfm) of each other. Given that recirculation may occur in some circumstances, the question arises as to how much recirculation constitutes a hazard for the face workers. Unfortunately, there is currently insufficient information to answer this. Emphasis must instead be placed on means to quantify the amount of recirculation between the scrubber and face area. Methods must also be examined to control this phenomenon. This paper presents a technique for quantifying recirculation and scrubber capture levels in a blowing face ventilation system. Several ventilation parameters are investigated to determine their effects on these levels. DEVELOPMENT OF RECIRCULATION EXPRESSIONS One way to measure airflow quantities at a point near the face would be to measure the gas flow rate Qgas, and gas concentration c at that location. The airflow Qair, would be simply the ratio of these two values, Qair, = Qgas/c. Although gas concentration values, c, can be obtained easily with existing gas monitoring equipment, it is more difficult to obtain gas flow readings, Qgas, at specific locations. To obtain these values of Qgas, another method was needed. Previous work in this area was conducted by Kissell and Bielicki (1975). However, the calculations in their model assumed a constant gas concentration in the region around the continuous miner. In a deep cut, it is questionable that gas concentrations would remain constant or uniform around the mining machine. The technique presented here does not rely on this assumption. It instead assumes that the gas concentration in the scrubber exhaust remains constant. A quantity of gas released at the cutting face either flows into the scrubber inlets or bypasses the inlets and flows around the off-curtain side (in this example, the right side) of the continuous miner (Figure 1). The fraction of the face gas that flows

Jan 1, 1993

By Thomas C. Anderson, Terry Weiss

The Mount Gunnison No. 1 Mine of the West Elk Coal Company (wholly owned subsidiary of ARCO Coal) had secured contracts to provide low sulfur, high Btu steam coal to various utility companies. This called for the development of the B-Seam at the Mount Gunnison Mine located some 400 feet below the operating F-Seam workings being mined with conventional room and pillar techniques. The B-Seam, to meet production goals, will be mined by a new 600-foot longwall machine making a 13-foot high cut. American Mine Services was awarded a competitively bid contract to drive two 2000-foot, 13-foot by 16-foot slopes at -15 percent, sink a 16-foot diameter ventilation shaft 400 feet between the F- and B-Seams, install a 60-inch conveyor in one of the slopes, remove 7000 feet of existing conveyor and rehabilitate 7000 feet in two entries to accommodate the placement of the longwall machinery. The slope portals were located 7000 feet in by the surface portal. Unique to the project was the placement of work shops and other infrastructure 7000 feet underground with an entry height of 6 feet. The $7 million contract was completed in less than one year using a mix of permissible (Schedule 31) and standard (Schedule 24) LHD equipment, all pneumatic jumbos and shaft sinking gear.

Jan 1, 1993

By M. Akram

Stability assessment of entry roofs is an essential precursor to all underground design. Both multi-seam interaction and longwall mining can subject entries to radical changes in the surrounding stress field. Such loading changes frequently produce instability and failure in the roof, floor and pillars. Roofs are shown to be vulnerable to stress-induced failures, particularly when the load is unsymmetrical. To predict the effects of changes in stress field, roof failure conditions under increasing loads were studied using finite element analysis and body loaded photoelastic models. A large range of geologic conditions were evaluated and incorporated into the model using Monte Carlo methods. Entry analysis using the model showed the roof to be particularly vulnerable to shear with the location of the failure site changing to meet loading and geologic conditions. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Based on this research a roof stability model SESAME was constructed for roof stability evaluation under specified loading conditions.

Jan 1, 1993

By R. D. Lama

This paper presents the results of a large scale trial of polycrystalline diamond picks (PDC) on longwalls with particular reference to dust control. Results from fixed position monitoring showed that PDC picks produced less respirable dust than tungsten carbide Point Attack picks. Dust generation at the longwall face was lower by 39 - 43%. Field trials also indicated that the life of a PDC pick to be at least 1460 tonnes/pick.

Jan 1, 1993

By Gerald H. Luttrell, Roe-Hoan Yoon

Flotation columns are becoming increasingly popular due to their ability to improve selectivity and to reduce operating costs. Unfortunately, these advantages are not often realized because of poor operating practices and difficulties associated with design and maintenance. This article provides guidelines for the operation and design of columns. The discussion will focus on designing proper wash water systems for improved selectivity, maximizing throughput by increasing the bubble surface area rate, and minimizing operating and maintenance costs. It is suggested that the design of the air sparging system is the most critical element in column flotation.

Jan 1, 1993

By L. J. E. Hofer, L. F. Zeiler, D. A. Giardino

The Jones Trickett Ratio (JTR) is generally used in investigations of fires and explosions for the determination of the composition of the fuel. This paper takes a close look at the JTR and finds it unreliable and ambiguous for the determination of fuel composition. A new index is presented, termed the (H/C) Index which uniquely determines the fuel composition. The (H/C) Index is simple to use requiring only the results of a single gas analysis of the combustion products. Experimental data testing the (H/C) Index for methane, propane, ethylene and coal dust are given, showing that the Index unambiguously determines the composition of the fuel. The (H/C) Index is also applied to the gas analysis data of several mine fires, illustrating how the Index changes with the progression of the mine fire.

Jan 1, 1993

By R. E. Johnson, L. V. Araújo, B. R. Palmer, L. M. Abrantes, G. W. Warren

The behaviour of chalcopyrite - mineral specimens and a Portuguese concentrate - in 2M chloride solutions prepared from hydrochloric acid and sodium chloride, has been characterized by cyclic voltammetry. The study has shown the influence of the potential and of the presence of impurities in the reaction schemes and their relative extent. The dissolution of chalcopyrite concentrate under potentiostatic control has been investigated and found to confirm the effect of the selected potential on the surface modification/rate of dissolution. An attempt has been made to correlate the information obtained with the response of the concentrate electrode to constant current treatments.

Jan 1, 1993

By P. M. Jones

Introduction The success of in situ leaching depends upon: • maintaining adequate injection and recovery flow capacities in wells, and • distributing leach solution effectively to contact and leach ore minerals within the target zone. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. As part of ongoing hydrological investigations into in situ leaching, the US Bureau of Mines (USBM) is studying factors affecting solution balance in an unsaturated copper ore deposit at the Cyprus Casa Grande Mine. The purpose of this study is to assess the effect of hydrogeologic features and in situ operating conditions on changes, during leaching, in: • solution storage within the deposit, and • solution balance. At the Casa Grande Mine, In-Situ-Leaching Test Facility, solution balance estimates are obtained for 10 selected intervals during 17 months of leaching under a variety of well configurations, pressures and flow conditions. Operational and geological description The Casa Grande Mine is located 32 miles south of Casa Grande, AZ. The mining area is within the Casa Grande Deposit, a porphyry copper stock consisting primarily of an intensely-fractured, granodiorite cap overlying a copper sulfide base. As a result of mine dewatering activity, unsaturated conditions existed in the deposit prior to leaching (Schmidt et al., 1990; Friedel and Schmidt, 1991). No groundwater was present in any of the in-situ-leaching, test-facility wells after drilling and prior to leach solution injection. Also, no ground water seepage occurs in the test-facility drift. The Casa Grande, In-Situ-Leaching Test Facility consists of 58 injection and recovery wells collared in an underground drift. The wells were drilled at various angles into the granodiorite deposit in a series of 15 divergent fans (Fig. 1). The fans are 12.5 ft apart and lie parallel to one another between the 900- and 1100-level drifts. Each fan contains three to five wells drilled at angles ranging from 6° to 89° from the horizontal. The wells can operate in an injection or a recovery mode. Currently, 36 flow sensors and 28 pressure transducers (part of a hydrologic, data acquisition system) are used to continuously monitor injection-well flow rates and pressures.

Jan 1, 1993

By Jozef F. Zurawski

The paper discusses design and construction of a 1.8 meter (6 ft.) diameter tunnel installed under complex geology of Staten Island, New York. Contract T-13 is a section of the Oakwood Beach Water Pollution Control Project constructed for New York City Department of Environmental Protection. A knowledge of the subsurface conditions and difficulties experienced on the adjacent contracts called for an innovative approach to handle tunneling under 12 to 17 meters (40-55 ft.) of water in the variable subsurface conditions. This paper describes tunnel design and construction utilizing continuous grouting during advancement of tunnel boring machine and installation of liner plates.

Jan 1, 1993

By G. Sanders

The studies reported on in this paper were initiated to draw attention to the severe contamination problem in the Section 30 drilling program at Chimney Creek. The lithologic-subset sampling study reached a different conclusion from that presented in your paper, and I wish to comment on your subsequent analysis of the data and your conclusions. Request for more complete data In the section on subsampling, you mention that the subordinate lithologies were separated and sampled, yet only the dominant-lithology gold value is plotted in Fig. 4. In a contamination study, the reader is interested in the assay values for the individual subsets. Please include a table of the subsample assay data in your reply. Also, please indicate which analytical methods were used to arrive at the gold values in the subsampling study. Turning barren rock into low-grade ore Figure 5 is very revealing and typical of all of the cross sections in Section 30. Note the long strings of low-grade mineralization spread out for hundreds of feet below the ore zones. There were some very high gold values found in certain contaminated fractions during the subset sampling. The conclusion, here, was that the distinctive, strongly-mineralized dolomite layer was probably loose and crumbly and continued to disintegrate during drilling. This caused salting of the unmineralized rock samples below.

Jan 1, 1993

By Ann M. Gosier

Over the past 20 years, diesel-powered equipment has been introduced into the underground mining environment in increasing numbers. While the introduction began years earlier in the metal-nonmetal sector, the exponential growth in coal mining use during this time has been more pronounced. Reasons for the continued use and rapid growth of diesel equipment in underground mines are easily understood. The safety and operational advantages afforded by this equipment in production and support systems are demonstrable. As other mine operators witness the advantages enjoyed by their competitors, they too move to introduce an increasingly diverse array of such equipment into their underground mines. As with any industrial technology, the use of diesel-powered equipment entails potential safety and health concerns. Existing Mine Safety and Health Administration (MSHA)approval regulations (30 CFR Parts 31, 32 and 36) apply only to diesel locomotives and mobile diesel-powered equipment for noncoal mines. In the absence of specific regulations, MSHA has required the use of equipment approved under Part 36 (gassy noncoal mines) for areas of underground coal mines where permissible electrical equipment is required. However, a considerable amount of diesel-powered equipment without explosion-proof or fire prevention features is in use in areas of coal mines where permissible electrical equipment is not required. It is on the use of this latter class of equipment that MSHA is focusing much of its regulatory attention relative to coal. The agency also is focused on revising existing occupational exposure limits for gaseous emissions and instituting limits on diesel particulate emissions for both coal and metal-nonmetal mines.

Jan 1, 1993

By S. I. Nozhko, V. N. Guliy, A. A. Zolotarev, L. M. Luyshnia

The study of the apatite deposits of the Aldan Shield shows wide spread of the Precambrian apatite-carbonate ores and possibilities of using them for extraction of apatite. Dependency of flotation on ore minerals was studied according to the following scheme: preparation of the monomineralic samples of anhydrite, gypsum, chlorite, serpentine, phlogopite, apatite; mixing them in apatite ore of the average composition; followed by flotation. Another series of the experiments was conducted to ascertain a dependence of flotation activity of the different minerals on the different flotation reagents, which were used as collectors. It has been shown that apatite from silicate-carbonate ores is most extractable because it has the biggest size of grains and is the most free of inclusions. Beneficiation of the sulphate-containing apatite-carbonate rocks is possible when flotol - 7.9 is used as a collector. Meanwhile, the use of the tallaktam leads to an increase in the sulphate recovery. The estimation of individual technological features of the layered Mghydrosilicates and their influence on the process of beneficiation has been examined using samples of apatite-dolomite ore (P205-8%) with the addition of the phlogopite, serpentine and chlorite. The results show that there is little influence of the chlorite presence on the flotation while the serpentine presence leads to a decrease of the flotation, because of its high specific surface area.

Jan 1, 1993

By Ivano Andreis, Giovanni Valent

The Yindaruqin Irrigation Project is designed to irrigate 57,000 ha of land in the central part of Gansu Province of People's Republic of China. Water for the Project will be diverted through an 87 Km long feeder canal which will convey 36 cubic meters per second from an intake on the Datong River. (Fig. 1) The feeder canal consists of approximately 10 Km of open channels, 75 Km of tunnels and 2 Km of siphons and aqueducts. This is the biggest self-flowing irrigation water control project in the Northwest of China and it is among the most interesting projects in China for the geological and environmental conditions. Nearly half of the investment in the Project is a World Bank Loan and contractors were chosen by means of international bidding. The Italian Company, CMC Ravenna, succeeded in answering the bidding for the construction of tunnels 30A and 38, perhaps the most difficult in the Project, submitting a TBM alternative to the conforming drill and blast contract recommendation.

Jan 1, 1993

By A. J. Monhemius, S. Raghavan, G. W. Warren, E. Peters, D. W. Furerstenau

A lyometallurgical process for extracting copper from an ore containing chrysocolla by leaching it with a kerosene solution containing LM 63 in the presence of small amounts of aqueous ammonia is described. The experimental results indicate that 70 to 75 percent of the copper can be extracted from the ore using an ammonia content that is about one-fourth the stoichiomeaic quantity required to leach copper in an aqueous leaching system. The rate of copper extraction was found to be a function of particle size, ammonia concentration and temperature. The large quantity of physically adsorbed water together with ammonia in the pores of chrysocolla provides a mechanism for the transport of copper to the external surface of the particles where it is complexed by the LM molecules and transferred into the organic phase. When size reduction accompanies leaching, the extraction process was found to proceed when only "trace" quantities of ammonia are present in the system. The kinetics of the extraction process appear to be controlled by a mixed (reaction and diffusion) mechanism.

Jan 1, 1993

Overview In 1992, US coal supply and demand were shaped more by weather conditions and the export market than by the economic recovery. Preliminary data compiled by the Energy Information Administration (EIA) (Table I) show that coal production declined slightly to 902 Mt (994 million st). Consumption, though, rose by about 1 % to 811 Mt (894 million st), trailing the 2.1 %growth in Gross Domestic Product. Contributing to the decrease were a sizable drop in coal exports and some coal stock withdrawals. Consumption increased largely because electric utilities turned to coal to offset a shortfall in hydroelectric generation caused by a drought in the Northwest. Apart from this, the demand for coal-fired generation was dampened by a mild winter in the northwestern and northcentral United States, and a cool summer in the central and eastern parts of the Nation. Coal use by other consumers was about the same as in 1991. The average delivered prices of coal to all consuming sectors decreased slightly in 1992, reflecting soft coal markets (Fig. 1). US coal exporters experienced a set-back in 1992 mostly because of losses in the European market. Total coal exports fell by 6% to 93 Mt (103 million st), the first decline since 1987. Coal stockpiles at the end of 1992 were about 1.8 Mt (2 million st) below 1991, despite stock buildups by some electric utilities in the East. Stocks were built up as a hedge against possible coal miners' strikes after the Feb. 1, 1993, expiration of the contract between the United Mine Workers of America and the Bituminous Coal Operators' Association.

Jan 1, 1993

By William M. Dowall

The recently completed in-pit crushing and conveying project at Phelps Dodge's Morenci Mine is rated among the world's leading materials handling projects. The operation involves the crushing and transport of more than 109 kt/ d (120,000 stpd) of copper ore, using regenerative conveyors capable of providing more than 5.5 MW (7000 hp) of equivalent electrical energy. The Morenci Mine is located 330 km (200 miles) east of Phoenix, AZ. Phelps Dodge Corp. owns an 85% interest in the mine. The remaining 15% is owned by Sumitomo Metal Mining Co., Ltd. and Sumitomo Corp. Copper has been continuously produced from the Morenci district since the late 1800s. Until 1989, run-of-mine ore was transported from active mining faces to the Morenci and Metcalf concentrators by truck and rail haulage. In that year, a system of in-pit, semi-portable crushing plants and overland conveyors was commissioned. This substantially reduced truck haulage and effectively eliminated rail haulage in the pit. The system used two semi-portable, in-pit crushing stations equipped with 60/89 gyratory crushers. The crushed ore from both plants reported to the first of two overland belt conveyors, arranged in series, for transport from the pit to a coarse ore stockpile. The system was "backed-up" by existing locomotive rail haulage.

Jan 1, 1993

By Liuming Wu, Willis Forsling

The complexation of Alizarin Red S (ARS) at the surface of hydrous fluorapatite particles has been investigated at 25.0 C by means of potentiometric titrations, adsorption experiments in 0.1 M NaCI ionic medium, and Diffuse Reflectance Infrared Fourier Transform spectroscopy (DRIFT) studies. A chemical model describing the reaction at the aqueous mineral surface has been established under equilibrium conditions according to the reaction [== -CaOH2 + HA2 - « _ =PO CaA2 - z + H30&apos;; to (int.) = -5.61 ± 0.02 3 a =PO- logBs-1110(int.) ( ) within the range 8.40 <_ -log[H ] <_ 9.80.] Experimental data were evaluated using the computer program FITEQL on the basis of a constant capacitance model for the electric double layer. The surface complex structure, has been proposed to involve the quinoid and alpha phenolic oxygens of ARS coordinated to the calcium sites on the fluorapatite surface.

Jan 1, 1993

By David J. Brown, Richard C. Fountain, Marc V. Hurst

The Central Florida Phosphate District, one of the most productive phosphate districts in the world, has been mined principally within Polk and Hillsborough Counties, Florida. Recent development is extending the district southward into Hardee, Manatee, and DeSoto Counties. This area is known as the Southern Extension. The combined area of these two phosphate-bearing areas encompasses about 2,000 square miles. Structurally, the district and its Southern Extension lie at the southern end of the Ocala Arch and are flanked by the Hillsborough High to the northwest. South of this area is the South Florida Embayment. The Osceola Low lies to the east. The phosphorite within the Central Florida Phosphate District generally dips very gently (<0.1°) to the south. The boundaries of the central Florida Phosphate District are generally defined by thinning of the phosphorite due the adjacent structurally high areas to the north, west, and east, and by increased clay, CaO, and MgO content reflecting lithologic differences to the east and south. The Bone Valley Member of the Peace River Formation and reworked sediments of more recent age were the primary ore-bearing horizon in the Polk-Hillsborough County area. As those reserves are depleted, the less desirable phosphorites of the Peace River Formation are being exploited in the Southern Extension.

Jan 1, 1993

By T. M. Barton, M. Gauna, A. A. Campoli

Coal mine bumps, the violent failures of overstressed coal, present a safety hazard to miners when longwall mining is conducted in deep, bump-prone coal mines. Two different longwall gate entry systems were evaluated in a southern Appalachian coal mine located in the Pocahontas No. 3 coalbed under approximately 610 m (2000 ft) of overburden that included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design used a 24.4-m (80 ft) square abutment pillar, while the new design employed a 36.6-m x 54.9-m (120 ft x 180 ft) abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worst-case conditions increased effective bearing area 62%, with only a 9% increase in gate entry system width, and eliminated face bumps that were experienced with the original gate entry design.

Jan 1, 1993

By W. E. Lindquist

Roasting of refractory gold ores has the primary goal of oxidizing sulfides and organics to improve gold recoveries prior to leaching. Commercial installations currently utilize bubbling and circulating fluidized beds. The principle of flash roasting is aimed at a more cost effective method of whole ore roasting for large throughput applications. Results of pilot plant testing and scale up to commercial design will be discussed in further detail in this paper.

Jan 1, 1993