Search Documents

By M. J. McPherson, P. Mousset-Jones, G. Danko, I. M. Konduri, F. Calizaya

The flow of air through a bare rock, underground airway is affected by the size and frequency of the micro- and macro-asperities of the rough surface. The focus of this study is to characterize this roughness using the coefficient of friction, the friction factor and the fractal dimension. The rough surfaces were identified by two sets of 177 and 78 transverse profiles measured by a laser profiler along the length of an underground airway at the Sunshine Mine, Idaho. Based on the measurements, the friction factor was estimated from Atkinson's equation and the coefficient of friction from the Moody diagram, and power series and variography were used for computing a fractal dimension for the airway surface. Significant conclusions are reached relating the effect of error in the measurement of cross-sectional and rubbing surface areas of a drift, on the estimated friction factor for the airway. The potential role of the fractal dimension as an alternative to the friction factor for characterizing the roughness of a mine airway is discussed.

Jan 1, 1993

By Y. Topkaya, Lloyd Petrie, Dianne Marozas, R. E. Johnson, Steven Paulson, J. H. Canterford, B. R. Palmer, R. B. Bhappu, Lorin Redden

This paper describes a fundamental approach to in situ leach mining (ISLM) lixiviant development which emphasizes leaching selectivity through detailed characterization of mineral-solution interfacial chemistry and post-leach geochemistry. This experimentation and modeling approach consists of: (1) petrographic identification of reactive ore and gangue minerals; (2) determination of leaching kinetics of individual minerals through batch leaching tests; (3) evaluation of bulk solution geochemistry through column leaching tests; and (4) ISLM simulation of element species transport and geochemistry through core leaching tests. Recent results confirm good leaching selectivity for manganese, but reveal post- leach precipitation and permeability loss during core leaching experiments.

Jan 1, 1993

By T. A. P. Sankar, S. Gundiah, Pradip, R. A. Kulkarni

Two modified polyacrylamide flocculants, namely polyacrylamide with glycolic acid functionality (PAMG), and a copolymer of acrylamide with N-acryloyl-[T]- aminobutyric acid (HPVP), were synthesized, characterised and evaluated for selective separation in apatite/quartz and apatite/dolomite/calcite systems, respectively. PAMG flocculant was found selective in the separation of tricalcium phosphate (TCP) from its mixtures with quartz at acidic to neutral pH range. The selectivity deteriorated at alkaline pH. In contrast, polyacrylic acid (PAA) flocculant was found most effective only in the alkaline pH range. HPVP flocculant (even though flocculating all three minerals namely apatite, dolomite and calcite) was observed to be quite selective for the separation of calcite from apatite-dolomite minerals in single mineral tests in the presence of sodium hexametaphosphate dispersant at neutral pH. There was, however, no selectivity observed during tests on synthetic mixtures. This loss in selectivity is attributed to the phenomenon of hetero-flocculation, as reported earlier, for separation in an apatite-dolomite system with polyethylene oxide.

Jan 1, 1993

By N. Rajmohan, K. T. Jacob

Presented is a thermodynamic feasibility analysis of extracting base metal chlorides from low-grade, multi-metallic oxide ores using CaC[1]2 as a chlorinating agent in the presence of SO2 and O2. The oxides react to form corresponding chlorides, while CaC[1]2 is converted to CaSO4. The Ellingham diagram is used for comparing the standard Gibbs' free energy change for the sulfation-chlorination reaction of a large number of oxides. Except for alumina, silica and chromia, most of the other metal oxides will be converted to their respective chlorides. The volatile chlorides can be condensed, and the chlorides present in the condensed state can be leached. A process is proposed that uses a nontoxic chlorinating agent and gives an efficient separation of the metallic values from the gangue.

Jan 1, 1993

By Robert A. Jankowski, George E. Niewiadomski

INTRODUCTION The utilization of longwall mining technology in the United States has steadily increased since the first longwall plow system was installed in 1952. At the errs of FY 1992, some 76 coal mines were employing longwall mining systems for coal extraction, and approximately 78 shearer and 3 plow faces are operating nationwide at any given time. Although the number of operating longwalls has remained relatively constant over the last five years, longwall production levels have increased significantly during this period. During the same timeframe, the number of continuous miner sections has decreased by 13 pct., from approximately 1438 in FY 1988 to less than 1250 in FY 1992. According to Mine Safety and Health Administration (MSHA) data, the average production of longwall sections increased from approximately 2400 tons per shift (tps) in FY 1988 to more than 3100 tps FY 1992. In fact, the average production has more than tripled since 1978, when it was only 850 tps. Approximately 25 pct. of operating longwalls are capable of producing in excess of 4000 tps. Longwall production currently accounts for nearly 36 percent of U.S. underground coal production, compared to 4 pct. in 1978. These improvements are attributed to improved longwall equipment and increased availability, larger longwall panels and automation. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust compliance problems more frequently than other mining system. Although dust levels have remained relatively unchanged over the past five years, averaging 1.6 mg/m3 and 1.9 mg/m3 based on results of operator and inspector sampling, respectively, during FY 1992, approximately 25 pct. of the operating longwalls were in noncompliance during any given bimonthly sampling cycle. Although modest gains in longwall dust control technology have been made, these have been overshadowed by significant increases in production rates. As more coal is mined, more dust is generated (Figure 1). Therefore, the increase in longwall productivity has meant that far more dust is being produced which must be controlled. [ ] In view of the current compliance record, any efforts to further increase longwall output, as has been forecasted, must be accompanied by: (1) the reduction of dust levels at existing operations through the proper installation and maintenance of suitable engineering dust controls; and (2) the advancement of dust control technology for today's and future longwalls that will enable all face personnel o work in an environment that is free of excessive levels of respirable coal mine dust. MSHA'S RESPIRABLE DUST CONTROL PROGRAM Since 1972, federal regulations have required each coal mine operator to continuously maintain the average concentration of respirable dust in the mine atmosphere during each shift in the active workings at or below 2.0 mg/m3 through the application of environmental dust control methods. The regulations provide for further reduction in the dust standard whenever the

Jan 1, 1993

By G. P. Larson

We define a specialized mineral market as follows: Specialized markets occur where a low volume of a given mineral is used to convey a large benefit to a specific product. Sales of these value added minerals to small markets generally require a different marketing approach than bulk or commodity markets for traditional minerals. Specialized markets are differentiated by several characteristics as listed in Table 1. [Table 1-Characteristics of Specialized Markets 1. Long-term sample evaluation 2. Small volume markets 3. Highly controlled properties 4. Customized specifications 5. Technical selling effort] Many of the specialized markets require long term evaluations before sales can be made. This can vary greatly depending on the type of industry and ultimate end-use of the final product. In some cases, complete evaluations may take from several weeks to years. Length of sample evaluation has no relationship to size of market. That is, the total market may be quite small or fairly large (e.g. from a few hundred pounds to a few million pounds). Uniformity of value added minerals from lot to lot is an extremely important characteristic for these markets. Variations that are of no consequence to one industry (or application) cannot be tolerated in another. This has led to customized specifications and test procedures for specific markets and applications. Because of the greater uniformity and customized specifications, the need for greater technical selling effort is required. This is particularly true in the initial developmental phases and contacts as well as in maintaining the account after the initial order. A small entrepreneurial organization can be used to advantage to achieve goals of sales and profit to these types of markets. The large commodity or bulk producer's sales and marketing organizations are not ordinarily equipped to give the necessary service or technical assistance to the specialized markets. The organization usually required for this type of marketing is given in Table 2. [Table 2- Specialized Marketing Organization Requirements 1. Flexible approach to technical and marketing problems 2. Versatile background in a broad range of industries 3. Laboratory backup when necessary 4. Marketing expertise 5. Technically competent management] In developing specialized markets, a flexible approach to both technical and marketing problems is necessary in understanding the needs and requirements of the industry and the applications involved. This flexibility is also helpful in adapting existing products to new market areas. Having knowledge of a range of industries as broad as possible can be very helpful. It often happens that a product developed in one area or industry can lead to its application in a different area with excellent results. Laboratory assistance for a wide range of tests and test procedures is an important asset in any development program for specialized markets. Laboratories can also assist in competitive evaluations. Marketing expertise and a management with some degree of technical understanding are necessary in to assign proper cost/ benefit ratios to a proposed new product or application of existing products. This is important since the total market volume can be small and the time required for initial contact to first sale can often be lengthy. Also, management's technical and marketing expertise is required in evaluating all possible options that can be considered viable when an application is presented. Once an organization of this type is in place, it is then possible to determine the needs of the marketplace, including when various minerals might have to be customized to fill those needs. There are generally two methods of marketing, as noted in Table 3. [Table 3- Method of Marketing 1. Product Driven -Develop a product with certain desirable properties and try to find a market to utilize those properties. 2. Market Driven -Know market well enough that when a need arises, it is possible to identify a product that will satisfy the need.] These approaches are not mutually exclusive and can be used at the same time. Marketing a value added mineral generally requires the "market driven" approach. Hence, the importance of a knowledgeable management as outlined above. To determine where needs and opportunities exist, several approaches can be used. Table4 lists some of the methods employed.

Jan 1, 1993

By R. L. Grayson, R. C. Althouse, L. A. Layne, M. J. Klishis

Introduction The researchers combine a detailed microanalysis of accident data and roof bolting field observations to develop new and meaningful risk indices for the roof bolter job classification. These indices incorporate information that has not been used in traditional measures of risk. The significant parameters that these new indices incorporate are the total number of accidents occurring within a particular work activity, the amount of time a miner usually spends performing the work activities in which the accidents occurred, and the average severity of the injuries incurred in the accidents. Being specific for a particular job, they aid comparisons among work tasks performed in the bolting cycle. The indices' specificity provide anew basis for reexamination of training and operational development of miners for specific jobs. Microanalysis The roof bolting microanalysis was performed by examining the empirical data and written summaries for all bolting accidents reported in the West Virginia Safety Information System (WVSIS) for the years 1983-1987. The WVSIS database contained more than 15,000 accident narratives. The microanalysis of bolting accidents covered 2083 reported personal injuries (RPIs). This large number of injuries, performed at an industry-wide level, provides a broad picture of the nature of roof bolting injuries. The analysis focuses on the activities associated with the cyclical routines of the roof bolting process. For this analysis, roof bolting tasks were categorized into work routines based on the sequence of work activities performed by roof bolters. Four work routines were identified within the overall bolting cycle. And these routines comprised 70% (1217) of all roof bolting accidents at the face. The routines include: face area preparation; tramming, positioning and setting the automated temporary roof support (ATRS); drilling holes; and installing bolts. The types of injuries most common within a routine and the average severity of those RPIs were also identified. Table 1 gives a breakdown of the percentage of accidents by the bolting routines. Another 19% of the roof bolting RPIs cannot be classified in a particular routine because of the vagueness of the narratives. However, it was clear that these accidents involved drilling holes or installing bolts. These results are consistent with previous research. It identified drilling and bolting, followed by tramming, as the most frequent sources of injuries (Helander, Krohn & Curtain, 1983). [Table 1-Accidents by bolting routines at the face Accidents Bolting routine Percent Number Face area preparation 18.2 222 Tram, position, ATRS 23.3 284 Drilling holes 34.2 416 Installing bolts 24.2 295 Total 1217] Roof bolter operators were involved in 82% (1706) of the 2083 accidents. The RPIs incurred by classified roof bolters occurred largely on working sections (95%) and at the face area on the working section (75%). Approximately 23% of the 1706 roof bolter RPIs occurred during tasks which were not part of the bolting cycle. These included belt utility work, providing supplies and section moves. Miners in other job classifications who were involved in roof bolting accidents accounted for the remaining 18% of the 2083 roof bolting RPIs. Among this group were section utility men and general laborers (41%), section machine operators (38%), and electricians and mechanics (11%). Another 9% were performing on-section supervisory functions. Face area preparation Face area preparation work led to a substantial number of injuries, although it accounted for the lowest number of injuries of the four routines. Several tasks were associated with the injuries incurred in this routine. Table 2 shows the percentage of injuries associated with face area preparation. [Table 2- Accidents occurring during face area preparation 26.6% Setting temporary and supplemental supports 24.8% Scaling roof and ribs 21.2% Installing ventilation devices 15.8% Handling supplies and materials 11.6% Miscellaneous tasks] The injuries commonly involved overexertion and 'struck by' falling coal and rock. Handling materials often led to overexertion injuries. Nearly 66% of the scaling-related injuries and about 33% of the injuries incurred during the setting of temporary supports involved 'strikes' by equipment, materials, top and rib. Tramming, positioning and setting the ATRS During tramming operations, workers were often struck by components of the machine and hit by loose roof and rib. Poor footing also led to slips, sometimes against the moving machinery. Table 3 gives a breakdown of accidents in this routine. Control levers were a significant problem in this routine.

Jan 1, 1993

By William J. Maloney

OVERVIEW Blind drilled shafts are becoming increasingly popular, particularly in the Appalachian coalfields, as a secondary and sometimes primary means of ventilation. The reasons for the rebirth of the blind shaft are mainly due to it's economics, timeliness, safety characteristics and inherent independence from underground operations. Historically blind drilling has been used to a limited degree in hard rock and tunneling ventilation. With the recent advances in cutters, bit design, equipment and lining systems, particularly in the Appalachian coalfields, blind drilled shafts are once again the shaft construction technique of choice to the educated ventilation specialist. [ ] HISTORY OF BLIND DRILLING Blind drilling has it's roots in numerous places, including the Nevada Test site, the coalfields of Appalachia and Germany along with the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin with oilfield drillers entering the industry on a project basis only to "pull in their horns" and return to the oil patch. Shafts completed by oilfield equipment range from the shallow 5' and 6' lined shafts on the Nevada test site to two (2) 10' lined, 730' deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths with the record being a 90" diameter, 6,150' deep shaft being completed in the Aleutian Islands of Alaska in 1969. EQUIPMENT Oilfield equipment is still being used on the Nevada test site but elsewhere specialized blind hole equipment has been developed to enhance the efficiency of particular applications. Where steel liners are required the A-leg derrick with a simple hoist and rotary system is used. The largest user of this type equipment in the world is the former USSR where blind drilling for mine ventilation is the norm. On applications where trip time and cutter changeout are a priority, top drive hydraulic rigs have been developed which are highly automated, efficient and mobile. These rigs are particularly well suited for tunneling applications where shafts are shallow and sites are usually tight.

Jan 1, 1993

By Floyd C. Bossard

A method of hand-calculating the air-cooling requirements of a conceptualized underground mining operation is presented for the reader's orientation. Separate air heat load calculations were conducted for adiabatic compression, electromechanical equipment, wallrock, broken rock, groundwater, and blasting operations. The air heat sources were calculated for four mining levels under conditions representative of a typical planned mining operation at depth. The total heat gain on each level will approximate the level air-cooling requirements. The results of these hand calculations can be further modified by the use of mine ventilation computer software that refine the heat-source calculations, predict underground ambient air temperatures, and establish the air-cooling requirements of a mine. INTRODUCTION The principal mining method employed is a modified vertical crater retreat (VCR) blasthole operation. Typical scopes range from 20 to 40 feet wide, 75 to 100 feet long, and 100 feet in height. Six and one-half inch blastholes are drilled with an "in the hole" hammer drill. Eight-foot high horizontal rounds are blasted down. Mucking of ore from the undercut to orepass is done with LHD equipment operated from a remote control station. Backfill includes hydraulically placed tailings with cement, and waste rock when available. Stope access is from ramp sub-levels on 50-foot vertical intervals. Crosscuts are ramped down to the first stope cut 25 feet below the sub-level elevation. Then the crosscuts are raised by taking down the back when each stope cut is completed, until an elevation 25 feet above the sub-level is reached. The crosscuts are filled with tailings, and/or waste rock. See Figure 1. Typically, a two-pronged approach to defining the air-cooling requirements is conducted. First, the principal sources that make up the air heat load are individually hand-calculated. Second, projections of mine heat load are calculated by utilizing computer modeling techniques. This paper discusses the first method (hand calculations) of determining the individual components of heat flow into the mine. CALCULATED AIR HEAT LOADS Adiabatic Compression The plans for the mine include delivery of 300,000 cfm of air to ventilate the lower level operation. This is equivalent to approximately 200 cfm/ton of rock produced (300,000 cfm/1500 tpd of ore and waste). As air flows down a shaft, with no heat interchange between the shaft and air and no evaporation of moisture taking place, the air is heated in the same way as if it were compressed in a compressor. Dry air increases in temperature about 5.4°F per 1000 feet. One BTU is added to each pound of air for every 778 feet of decrease in elevation, or is subtracted for the same elevation increase. For dry air, the dry-bulb temperature change is 1/(0.24 x 778) = 0.00535°F/ft., or 1°F/187 ft. elevation. Auto-compression may be masked by the presence of other heating or cooling sources, such as shaft wallrock, groundwater, air and water lines, electrical facilities, etc. The major factors influencing the temperature of the air delivered underground by a shaft are (1) the night time cool air temperature's effect on the rock or lining of the shaft, (2) temperature gradient of ground rock related to depth, and (3) evaporation of moisture within the shaft which increases the latent temperature and decreases the sensible temperature. [Calculation For Adiabatic Heat of Compression] a. Assumptions: 1. Three hundred thousand cfm of fresh air at 3000 level has increased in temperature during the summertime to the point where it has little available cooling power. Air-cooling will be required on 3000 Level and below. 2. Elevation of 3000 Level is approximately +1000 ft. above sea level.

Jan 1, 1993

By J. E. Gebhardt, D. A. Rice, P. E. Richardson

An improved understanding of the significant role of electrochemical reactions in sulfide flotation has evolved in the past 20 years, This understanding has been accompanied by a corresponding increase in attempts to control the electrochemical potential of flotation pulps for monitoring and controlling sulfide flotation circuits to improve metallurgical performance. This paper discusses the basic electrochemistry of sulfide flotation and the use of electrochemical potential as a control parameter.

Jan 1, 1993

By Randall D. Peterson

Economic operation of a mine ventilation system must include some means by which operating costs can be quantified and evaluated periodically. Current practice at most mines relies upon the best judgement of foremen, engineers and managers to identify high cost or problem areas in the system and to estimate potential costs and benefits of work proposed to reduce inefficiencies. The problem with this is that significant savings can be overlooked or sub-economic projects may be undertaken when sufficient attention is not paid to the interrelationship between airflow characteristics and corporate financial criteria. In order to accurately determine costs and benefits it is necessary to view the solution of each potential ventilation problem as a separate economic opportunity.

Jan 1, 1993

By Odd G. Askilsrud, Steinar Johannessen

New powerplants, tunnels and dams are currently under construction at Meraaker to triple the annual power production of a nearly 100 year old power scheme. A total of 44 km tunnels with cross sections varying from 7 m2 to 32 m2 have been excavated in hard rock formations. Ten kilometers were excavated by a High Performance Tunnel Boring Machine (HP TBM). The remaining tunnels have been completed by the drill and blast method, using modem proven equipment and procedures. This paper gives special attention to the TBM drive and equipment selection, including, planning, site organization and performance.

Jan 1, 1993

By Albert E. Ketler

The AirBoss*200 is a unique ambient airflow sensor with important improvements in accuracy, especially in the critical low end, 0-61 m/min (0-200 fpm) where MSHA regulations apply. All solid state, its design is rugged, and there are no moving parts or delicate filaments. An on-board microprocessor calculates air velocity, linearizes and corrects for temperature, while driving voltage and current loop analog outputs to .3 meters/minute (1 ft/min) resolution. Recent developments also cover both positive and negative flow directions. A hand held computer is available to readout data and to adjust stored range selection, alarm set points, calibration data and the speed of response. Installation in hazardous areas is covered by MSHA Classes G, H and L.

Jan 1, 1993

By J. Harrison Daniel

Increasing concerns of industrial hygiene and worker health issues and resulting regulatory actions, coupled with continuing advances in mining systems, are placing new burdens on the industry and Federal Government; particularly, mine ventilation departments. More encompassing worker health programs are required to respond to Federal promulgation of regulations and to keep abreast of techno- logical advances in the mining industry. The relationship between the mining industry and Federal agencies involved in rulemaking is presented, along with the rationale of an Industrial Hygiene Management Plan. This plan or strategy focuses on developing partnerships and collaborative research groups to address the controversial health issues facing not only the mining workforce, but our society.

Jan 1, 1993

By M. J. Virnig, Christopher A. Fleming

THE CIP PROCESS "IN THE RIGHT PLACE AT THE RIGHT TIME? After its tentative introduction to the precious metals mining industry in the earlier part of this century, the carbon in pulp (CIP) process has now come of age, and is the process of choice on all new gold mills. Well over 50 percent of all gold that is mined each year is recovered by adsorption on activated carbon, and the percentage will increase in the years ahead, when old mills using Merrill Crowe technology come to the end of their lives, and as the proportion of world gold production from low-grade resources increases. The pioneering process development work in this field, which was mainly concerned with carbon elution, was carried out by Zadra and his colleagues at the United States Bureau of Mines in the early 1950's (Zadra et al., 1950, 1952), and led to the commissioning of the first large-scale, industrial CIP plant, at the Homestake Mine in South Dakota, in 1973 (Hall et al., 1974). From there, the process spread rapidly, firstly in South Africa in the late 1970's. and then throughout the rest of the gold producing world in the 1980's. There were several factors that led to the meteoric (by gold industry standards) acceptance and successful implementation of this new technology into gold processing operations worldwide. Firstly, and perhaps most fortuitously, the development of the technology closely paralleled the 1968 release of the gold price from the rigid constraints of the $35/oz. gold standard. With the value of the metal allowed, for the first time in modern history, to fluctuate in response to free market supply and demand forces, the gold industry witnessed an unprecedented boom as the price of their commodity increased ten-fold in a remarkably short period of time. This had several important spin-offs as far as new process developments were concerned: The profits realized by established gold-mining companies increased enormously and, consequently, there was more to spend on research and development and exploration for new deposits.

Jan 1, 1993

By Wu Chao, Wang Pinglong, Meng Tingrang

This paper discusses the research results of sulphide ore properties with respects on self-heating and the assessment techniques on mine spontaneous combustion for several mines of sulphide ores in China. A group of experimental devices for testing the chemical behaviour of sulphide minerals, the geological structures, the rate of oxygen absorption, the initial self-heating temperature, and the ignition point of ore samples, etc. are also described in detail. These methods have been proved to be effective by several sulphide mines which all have the history of spontaneous combustion of sulphide ores. INTRODUCTION A fire disaster from the spontaneous combustion of sulphide ores in a mine can produce large quantities of toxic gases and heat to pollute the working environment, lead to large economic losses and loss of human life, and even compell the mine to be closed. Some mines of copper, lead, zinc, tin and iron in China are of high content of sulphur. It is of great importance to evaluate the potential of spontaneous combustion of sulphide ores before beginning to design and mine the ore deposits. At present, the mechanism of spontaneous combustion accepted commonly is that sulphide ores undergo slow oxidation on exposure to moisture air at ambient temperature, with the evolution of heat, gases and moisture. The heat generated, if not dissipated, gives rise to an increase in the temperature of the sulphide ores. As the temperature of the sulphide ores rises, the rate of oxidation increases. If this is allowed to proceed unchecked it can eventually result in the ignition of the sulphide ores. For pyrite (FeS2), it reacts with oxygen and water according to the following equations.

Jan 1, 1993

By D. Gu

Shaft drilling is one of the most useful methods of driving shafts. This paper describes the application and development of the technique in coal mine construction in China.

Jan 1, 1993

By Ian M. Loomis, Keith G. Wallace

The Waste Isolation Pilot Plant (WIPP) is a U.S. Department of Energy research and development facility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste. The waste storage horizon is 655 m (2150 ft) below surface in bedded salt. To date the WIPP project has not emplaced any waste. There are three intake shafts used to supply air to the underground. All air is exhausted though a single return shaft. The total design airflow during normal operations is 200 m3/s (424,000 cfm). The ventilation system is designed to provide separate air splits to construction, experimental, and storage activities. Separation is achieved by isolating the storage circuit from the construction or experimental circuits with bulkheads. Any air leakage must be towards the storage area of the facility. Field studies have shown that the pressure differential necessary to maintain the correct leakage direction is susceptible to the effects of natural ventilation; therefore, extensive studies and analyses have been conducted to quantity the natural ventilation effects on the WIPP underground airflow system. A component of this work is a monitoring system designed to measure the air properties necessary for calculation of the natural ventilation pressure (NVP). This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure at strategic locations on surface and underground. The psychrometric parameters of the air are measured every fifteen minutes. From these data, trends can be determined showing the impact of NVP on the ventilation system during diurnal variations in surface climate. Both summer and winter conditions have been studied. To the author's knowledge this is the first reported instance of automatic and continuous production of time and temperature variant NVPs. This paper describes the results of the initial monitoring study. INTRODUCTION The ventilation system at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico, is designed to perform two distinct functions. First, it supports normal mine ventilation requirements complying with all state and federal mine regulations. Second, the system is designed to prevent an uncontrolled release of radioactive contaminants from the storage and transportation areas of the facility. Although a nuclear radiation release in the facility is considered unlikely, many special features are implemented in the ventilation system to prevent the possible spread of contamination. The facility is constructed with the waste transportation and storage areas separated from the mining and non-radioactive experimental areas. The ventilation system is designed such that air leakage is from the mining and experimental areas to the storage areas. Furthermore, radiation detectors are located throughout the storage and waste transportation areas underground and an exhaust filtration building is installed on surface to prevent the possible release of radiation to the environment. For over two years the underground ventilation system has been rigorously tested and balanced. It was during this period that the adverse effects of NVP were noticed and subsequently quantified. From extensive field studies and computer models, several mitigating features were designed and constructed and special operational procedures were implemented to control the impacts of NVP. To quantify more accurately the NVP at the WIPP, a continuous monitoring system was installed. This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure every fifteen minutes at strategic locations on surface and underground. From this psychrometric data, the NVP is calculated. Fan operating pressures and flows and strategic differential pressures are recorded from the site Continuous Monitoring System (CMS). The monitoring system provides a means of evaluating how the ventilation system behaves in regard to climatic conditions and to judge the efficacy of the mitigating features and operational procedures. To the author's knowledge, continuous calculation of NVP as a function of time and surface temperature has not been previously reported. Overview of the Waste Isolation Pilot Plant The U.S. Department of Energy determined that the plastic nature of bedded salt may provide the best solution to isolate transuranic (TRU) waste from the biosphere. Initial evaluations at the WIPP site began in 1974. In 1979, the United States Congress enacted Public Law 96-164 for the construction and development of the WIPP project. The mission of the WIPP is to demonstrate the safe, long-term disposal of TRU waste generated by the national defense programs of the United States. TRU waste is classified as a low to medium level waste. The waste is stored in drums and does not produce significant heat (not greater than 1 W per drum). The WIPP site is located approximately 47 km (29 miles) east of Carlsbad, New Mexico in the Chihuahuan Desert. The repository is located in the 630 m (2000 ft) thick Salado Formation. This Permian Basin salt deposit is about 225 million years old and appears to have been minimally disturbed by earthquake, faulting, and ground water activity since it was deposited. The underground facility is 660 m

Jan 1, 1993

By C. J. Myers, D. L. McKinnon, A. A. Dasys

In 1988, the National Institute of Occupational Health and Safety (NIOSH) published an information bulletin stating that whole diesel exhaust should be considered a probable carcinogen. Since then, regulations across Canada and the United States (Mine Safety and Health Administration, MSHA) have looked at appropriate exposure limits for underground mine workers. In Canada, an interim standard of 1.5 mg/m3 Respirable Combustible Dust (RCD) has been adopted by some provinces and is being looked at by others. MSHA is considering levels as low as 0.5 mg/m3 soot. Golden Giant, being aware of regulatory developments, decided to look at means of reducing diesel particulate on thier large production machinery. This machinery (LHDs and haulage trucks) is powered by Detroit Diesel 71N Series engines and is used to produce 3000 tonnes of ore/day with a longhole mining technique. Having looked at the various control technologies, it was decided to evaluate the potential of using diesel particulate filters with a copper-based fuel additive for regeneration (the process by which collected particulate is burned off). This paper outlines the control technology used and the results of the field evaluation indicating the benefits to the underground mine worker.

Jan 1, 1993

By C. D. Harrison, G. S. Stallard

The 199O Clean Air Act Amendments specify national objectives for reducing sulfur dioxide emissions from coal fired power plants. System-wide reductions can be achieved by combining various emissions control technologies and allowances, or compliance credits, that can be purchased, sold or traded. As part of the Coal Quality Expert development project funded by the US Department of Energy and the Electric Power Research Institute (EPRI), Black & Veatch has developed an interactive computer tool, the Acid Rain Advisor (ARA). Through this program, integrated, system-wide compliance plans are generated by comparing the costs and emissions reduction benefits of emissions allowances and various SO2-control technologies (coal cleaning, fuel switching, scrubber retrofits, etc.)

Jan 1, 1993