Search Documents

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

"The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities (82%) may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis. Among coal and rock dust exposure, high noise levels, roof and rib falls, and the potential for fires and explosions, operating and working with heavy machinery poses a significant risk to miner safety. One of the most hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 39 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are now required on all operating CMMs in underground coal mines with the exception of full-face CMMs [1]. Commercially available proximity detection (cPD) systems are based on the principle of magnetic flux density (B-field). Typically, four magnetic field generators are positioned on a CMM, and personal alarm devices (PADs) are worn by the miners that detect magnetic flux density difference. As a miner wearing a PAD gets closer to the machine, the flux density increases. Zones can be constructed around the machine so that an alarm will trigger on the PAD based on the flux density."

Jan 1, 2016

By Juan Ares, Enrique Fernández, Alejandro Sanz, Francisco González

"INTRODUCTION Crossrail is a subsidiary company of Transport for London created for the construction of a new transverse train line 118 km long between Maidenhead and Heathrow in the West, and Shenfield and Abbey Wood in the East, including 21 km underground below London. Crossrail C305 Eastern Running Tunnels project is the biggest contract within Crossrail Project and involved boring 11.8 km of twin tunnels through London’s city center. Crossrail C305 Project interfaced with different contracts along its alignment and therefore logistics and solutions had to be developed to minimize disruptions or interferences with other contractors and the neighborhood. The paper describes this innovative approach. C305 CONTRACT APPROACH C305 contract was split into three drives, to be excavated by four EPB TBMs 7.1m diameter, as shown in Figure 1. •,Drive Y: 8.2km long between Limmo Peninsula and Farringdon Station in the city center •,Drive Z: 2.7km long between Pudding Mill Lane and Stepney Green Junction •,Drive G: 0.9km long between Limmo Peninsula and Victoria Dock Portal in the East. Crossrail C305 Project scope of works included the excavation of TBM tunnels and shafts at Limmo Peninsula and Stepney Green (including 17m span turnout caverns), along with the requirement to traverse station and shaft structures of other Crossrail contracts. Limmo Peninsula Site was a strategic element as it was the only access point on the tunnel alignment with sufficient available area at the surface for tunnelling logistics and also connected to the Lea River, tributary of the River Thames which facilitated marine operations for segment supply and muck removal. These were the reasons for operating Drive Y & Drive G TBMs from that location. Drive Z TBMs were originally planned to be launched from Stepney Green to Pudding Mill Lane, supplying the TBMs during Drive Z excavation from Limmo Peninsula site through the excavated section of Drive Y between Limmo and Stepney Green. During the early stages of the project, a value engineering proposal with a new tunneling strategy was agreed wherein the Pudding Mill Lane contractor would provide space for TBM assembly and operation in their portal, allowing for reversing Drive Z excavation and launching the two TBMs from Pudding Mill Lane. This optimization reduced some of the shaft requirements at Stepney Green which were contingent upon critical enabling works and provided program certainty and cost savings for the full Crossrail Project. It allowed for the reuse of both the Drive Z TBMs for Drive G excavation from Limmo to Victoria Dock Portal thereby saving on the procurement of two TBMs, in addition to easier logistics for both Drives Y&Z, therefore de-risking the TBM excavation process and the C305 Project program completion."

Jan 1, 2016

By A. Taghavi, I. Hassan, A. Solecki

"The Eglinton Crosstown Light Rail (LRT) Project is part of an $8.4 billion investment to expand transit in the Toronto, Canada area and is the largest transit project initiated in Province’s history. Settlement control and impact to over 1400 adjacent structures due to tunnelling was identified early as a critical project risk. The ground conditions along the 10km tunnel alignment consist of water bearing soft ground deposits (clays, sands, silts) which required careful analysis and control during design and construction. This paper will describe the process used to analyze settlements along the numerous of adjacent structures and evaluate achieved settlement results to those used during design. The paper will demonstrate that with the appropriate design specifications, selection of modernized EPB machines, and contractor performance, settlement can be maintained well below typical industry (volume loss) standards, expanding the application and suitability of soft ground tunnelling in sensitive settlement areas. INTRODUCTION The Eglinton Crosstown Light Rail Transit (LRT) Project is part of an $8.4 billion (2010$ CND) investment from the Ontario provincial government to expand transit in the Toronto, Canada area. The project is being developed by Metrolinx, an agency of the Government of Ontario to provide 19 kilometers of dedicated LRT service connecting the City of Toronto from the west to east along Eglinton Avenue. Upon completion in the year 2020, the Crosstown will be the first LRT constructed in Toronto. It will link regional and local transit, cut travel time along the route by half and provide over a thousand jobs during construction."

Jan 1, 2016

By T. R. Ley

"INTRODUCTION Brutally honest mining executives will tell you that “safety is job #1 but.. dollars are also extremely important”. When economic times are tough, as they are now in mining, it can feel like you need to choose between safety and cost control. Leading edge companies know that it is excellence at both that provides the best performance. FLUID POWER SYSTEMS Fluid power systems are ubiquitous in mining – longwall systems, continuous miners, drills, haul trucks and excavators, etc. And fluid power systems are getting more powerful and using higher pressures to move greater volumes and achieve higher productivity. Average operating pressures in mobile equipment has been rising to 450 bar (6,500 psi) over the last decade. With increased system pressure comes ever increasing levels of stored energy. Stored energy that, if released in an uncontrolled fashion, can do tremendous harm to people and things.Fluid power systems are composed of pipe, flexible hoses, pumps, valves and actuators. They are filled with fluid (mineral oil or fire-resistant) to transmit power to where it’s needed for performing work. With time and use fittings can loosen, component performance diminishes and hoses wear and tear. In hostile environments, like coal mining, hydraulic hoses can fail in as little as 2 years according to DGUV (umbrella association of German Accident Insurers), maybe sooner in some particularly challenging environments. FLUID POWER SYSTEM SAFETY While appearing simple and benign on the surface, fluid power systems, particularly such systems on mobile equipment, have many potential hazards. Hazards that most workers aren’t aware of – particularly young, new hires. And those hazards that can quickly turn deadly. During the past couple of years, including at last year’s SME Conference, I talked to a wide variety of mining people about high pressure fluid injection injuries. Some people, often with little or no field experience, never heard of it. But, people with mine operations / maintenance experience were almost always aware of such injuries.Some had even seen it happen right in front of them. But most claimed it didn’t happen all that often. It just wasn’t seen as a problem!"

Jan 1, 2016

By S. Lee, F. Campero

"Past heap leach design has evaluated hydrodynamic parameters based on a uniform particle size of heap material, but has ignored the equal importance of the instability of fine migration within heap stack in the beginning stages of the irrigation process. The proposed probabilistic model evaluates internal fine erosion and segregation potential of well-graded crushed ores by considering the entire particle size distribution shape and site compaction degree. Using this model, unsaturated flow model parameters were successfully evaluated based on synthesized soil-water characteristic curve (SWCC). Additionally, one-dimensional unsaturated transient flow modeling with Hydrus 1D® showed that the different recovery efficiencies of heap material under unsaturated flow patterns depending on the particle size distribution and compaction degree of heap material. Agglomeration preprocess employed by most heap leach sites can reduce the potential of fine erosion within heap material significantly, but internal stability of crushed ores and hydrodynamic-based analysis of heap material’s pore structure is equally important in the prescreening stage in order to improve efficiency of the heap leach and avoid a costly agglomeration process. INTRODUCTION Accurate estimation of heap leach recovery is a difficult task due to the variety of design parameters that need to be considered - such as geochemistry, hydro-dynamics, and geotechnical design aspects, most notably particle size distribution through the process of agglomeration. After agglomeration techniques were introduced to heap leach design, the influence of particle size distribution and compaction degree in enhanced heap leach recovery has been neglected. The main purpose of agglomeration is to prevent fine segregation and internal erosion during and after heap stacking for well graded crushed ores, which will eventually diminish heap reach recovery. Recent studies show that agglomerated heap materials that had been consolidated at 10 meters below heap surface can release the fines after contact time with lixiviant to the compacted heap material and produce poor drainage performance (Milczarek et al, 2013). It must be noted that engineers and practitioners should investigate feasibility of agglomeration benefit prior to heap leach design because the agglomeration process can incur up to 20 or 30% of project costs. Internal stability of stacked heap material is mainly governed by the particle size distribution of crushed ores. Depending on this stability, segregation and internal erosion of fines can be mitigated by the application of moderate compaction effort during heap construction. Investigation of segregation and internal erosion potential therefore takes precedence for well graded crushed ore since reaction time and contact area with lixivant are greater in finer ores."

Jan 1, 2016

By J. Herhold, S. Plaum

"Increasing worldwide energy demands, coupled with desires for cleaner energy, have led to greater research of renewable energies. Strongly weather-dependent energy sources, e.g. solar and wind energy, are unable to provide a constant control energy to withstand the fluctuation of the extensive power systems during peak hours. The pump storage plant Nant de Drance in Switzerland will not only have the capacity of a nuclear power plant, producing 900 MW, but will also combine the environmental aspect and the demand for controlled energy. Nant de Drance is one of the pioneer projects for upcoming energy challenges and serves as a model for future pump storage plants. This paper focuses on the planning process and the project execution of interdisciplinary large-scale projects such as Nant de Drance, including project related data handling, communication systems and project handling skills. Furthermore, the paper discusses mining excavation in the context of large scale projects and their regional environmental challenges, e.g. high alpine rock mass on the site of Nant de Drance. PROJECT BACKGROUND Project Overview Nant de Drance is a 900 MW pump storage plant located in the Swiss Alps. To provide such a high energy storage, six turbines (reversible Francis type), each with a capacity of 150 MW, were installed. Due to the efficiency factor of 80% the pump storage plant is able to provide an energy production of 2500 GWh per annum. Construction of the pump storage plant, which has been selected as “Major Tunneling Project of the Year” in 2014 by NCE and ITA-AITES, will be completed over 10 years. Therefore, the project has been divided in six major phases outlined below: - Launch: 2008 - Access Gallery: 2010 – 2012 - Excavation KMA, KTR: 2011 – 2014 - Concreting KMA, KTR: 2014 – 2016 - Installation of HEM equipment: 2014 – 2018 - Tests & entry into service: 2017 – 2018 Figure 1 outlines the single process phases of the project. For the construction of the shafts, galleries and caverns, 1.7 million m³ of metamorphic rock with sedimentary origin (mica schist & paragneiss of the massif „Aiguilles Rouges“) were excavated. A tunnel network with a total length of 15 km was created. The machine cavern measures 194 m long, 32 m wide and 52 m tall."

Jan 1, 2016

By Pier Francesco Paglini, Gian Luca Menchini, Pier Francesco Boschi

"PROJECTThe “Caltanissetta” Tunnel is part of the ANAS S.p.A (National Autonomous Roads Corporation) $ 1.3 Billion Highway 640 Caltanissetta-Agrigento (Sicily, Italy) Rehabilitation Project, consisting in upgrading of 62 km (40 miles) of highway. The Italian multinational construction company Cooperativa Muratori & Cementisti di Ravenna, is the General Contractor for the design and build contract. The highway S.S. 640 starts from Porto Empedocle, to the intersection with the Motorway A 19 Catania-Palermo.The entire project, double carriageway designed for speed 70-120 km/h and maximum longitudinal slope of 4.2%, is divided into two sections. First Section: just finished and opened to traffic. Second Section: mainly involving the province of Caltanissetta, length about 28 km (18 miles), works started in 2013. This second section includes the most challenging work of all the project, the “Caltanissetta” tunnel consisting of two separate tubes, each with 3.9 km length and inside diameter of 13.50 m, in order to host 2 traffic lines and an emergency line. HORIZONTAL AND VERTICAL ALIGNMENT - GEOLOGY AND HYDROGEOLOGYThe plan alignment of “Caltanissetta” tunnel is formed by two tubes which are located at a minimum mutual distance of 22 m to a maximum of 63 m, with n. 9 pedestrian and n. 4 road cross passages; ventilation shafts are not provided. Overburden over portals area is about 5 m till a maximum of 120 m. Tunnel sections have variable longitudinal slope from 2.6% to 0.5%, transversal slope of about 3.5%. Right tube length is 3,992 m, left tube length is 3,877 m."

Jan 1, 2016

By Thibaut Pannetier, Damien Rogat, Catherine Larive, André Regnard, David Chamoley

"INTRODUCTION For several decades, the use of fibre-reinforced sprayed concrete (FRSC) has been becoming increasingly widespread, either as a replacement for or in addition to traditional reinforcements. Macro-synthetic fibres appeared on the market at the same time as metal fibres (in the 1980s), but their use has developed more recently in France, starting in the early 2000s. While their properties are attractive for underground operations, their long-term performance remains the subject of some controversy, particularly with regard to the phenomenon of creep [1-5]. Unfortunately, the many differences of protocol among the studies carried out (materials, metering, spraying equipment and test methods, etc.) mean that, in general, the results cannot be compared. Although several methods have been developed to assess the bending creep behaviour of fibre-reinforced concrete, the majority of them test notched beams resting on isostatic supports. There are currently no standardised test methods adapted to FRSC on hyperstatic supports (as is the case for FRSC used for underground support). The Asquapro association has thus developed a new test specially designed for this type of concrete. Slabs of thickness 10cm, measuring 60 x 60 cm in plan have been sprayed and tested under bending stress according to a test procedure inspired by the standardised test of energy absorption capacity (NF EN 14488-5). An experimental campaign was launched in October 2014 to study the behaviour of seven types of sprayed concrete, manufactured using the same concrete matrix: six of them were reinforced with different metal or macrosynthetic fibres and the seventh with a welded wire mesh. Fourteen slabs were sprayed for each type of concrete and also for the non-reinforced concrete with the same matrix. The types of mechanical performances measured were the compressive strength and energy absorption capacity (at seven and twenty-eight days), in addition to the creep behaviour of these seven types of concrete, placed under stress on the seventh day. This article follows on from that published in the WTC 2015 congress proceedings [6]: the programme and the test methods are briefly described here and the results available at the time of writing are presented and discussed."

Jan 1, 2016

By Faruk Oksuz, Dave Schiemann, Matt Trotter, Mike Padilla, Miguel Sanchez, Carmen Scalise

"Chicago’s Tunnel and Reservoir Plan (TARP) is a nearly $4.0 billion and over 30 years long program and arguably the largest and longest combined sewer tunnel and reservoir system in the world. Recently, a massive tunnel construction is underway for connection of the McCook Reservoir to the existing TARP tunnel system. Once completed in two stages in 2017 and 2019, the reservoir will hold 38 billion-liters (10 billion-gallons) of combined sewer overflows (CSO) and flood waters from the city of Chicago and over 20 communities in Cook County, Illinois. McCook Main Tunnel will connect Chicago TARP’s Mainstream Tunnel to the McCook Reservoir. Connecting two 10-meter (33-ft) diameter tunnels at 92 meters (300 feet) underground has not been a simple task for the McCook Tunnel Project participants, the project owner U.S. Army Corps of Engineers (USACE), local sponsor Metropolitan Water Reclamation District (MWRD) of Greater Chicago, designer Black & Veatch, and the contractor, Kiewit Infrastructure Company (Kiewit). Yet alone excavating and lining massive size tunnels, the team is also challenged with live tunnel conditions in TARP Mainstream Tunnel that carries CSO and flood flows from city of Chicago which runs full during rain events and must remain in service at all times. The project is a noteworthy feat for engineering and construction with the upcoming installation of world’s largest underground wheel gates for flow control within the tunnel. In this paper, we describe one of its kind elements of this major tunnel system along with key design and construction considerations, specifically for the live tunnel connection which is a rare occurrence in the tunneling industry. INTRODUCTION The McCook Main Tunnel system consists of a 10 m (33 ft) finished diameter and 490 m (1,600 ft) long hard rock tunnel constructed from a 27.5 m (90 ft) diameter and 92 m (300 ft) deep main gate and tunnel construction access shaft. The gate shaft houses six high head 4.4 m by 9 m (14.5 ft by 29.5 ft) wheel gates to be installed in the bifurcated and steel lined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir."

Jan 1, 2016

"Use of the Bond Work Index to size industrial grinding equipment was widely known. Bond also described its application for measuring grinding circuit efficiency. Bond Work Index efficiency has been widely used by industry, but until now without concise standard methods, or a formal guideline, for doing so. The Bond Efficiency Sub-Committee of the Industrial Comminution Efficiency work group of GMSG has produced such a guideline, which follows. It covers the methods and provides examples of how to calculate the Bond Work Index Efficiency of most industrial grinding circuits. Bond Work Index testing equipment and methods are also provided. The next steps are: (1) to establish standard reference testing materials and one or more laboratories to serve as bases for reference testing; (2) to establish the accuracy of relative circuit Work Index Efficiency determinations; and (3), to develop and provide a public data base of industrial comminution circuit Bond Work Index Efficiencies. OUTLINE Introduction and Background Part 1. Determining the Bond Efficiency of a Grinding Circuit Method Demonstration/Example Calculations Bond Work Index Testing Equipment and Procedures Accuracy of Comparative Circuit WI Efficiency Determinations (under development) List of Symbols Part 2. Data Base of Bond Grinding Circuit Efficiencies (under development) References Annexes: A1. The Bond Crushing WI Test Equipment and Procedure for Bond Efficiency Determinations (Revised March 26, 2015) B1. The Bond Rod Mill WI Test Equipment and Procedure (Revised March 26, 2015) C1. The Bond Ball Mill WI Test Equipment and Procedure (Revised March 26, 2015) Introduction and Background Please see the references and slide presentation “Bond Efficiency SLC (rev3)-print.pdf.” This efficiency determination applies to most brittle materials in their naturally occurring (un-scalped) size distributions being treated in size reduction circuits down to a product sizing of approximately eighty percent passing 70 µm (see below). Unusually shaped materials (e.g. mica) should be regarded with caution. Part 1. Determining the Bond Efficiency of a Grinding Circuit Method In the plant: • Define the circuit for which the WI efficiency is to be determined • Procure samples of the circuit feed and product • Obtain the power draw of the size reduction equipment at the drive pinion(s) • Obtain the circuit throughput rate (dry tonnage) In the laboratory:"

Jan 1, 2016

By Michael Vitale, Lee W. Abramson, Daniel McMaster, Andrew J. Thompson

"Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on four recently constructed rock tunnel projects in New York, Ohio, Georgia and California. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed. INTRODUCTION Tunneling is a risky business. More than ever, attention is being paid to the risks associated with tunneled facilities and implications on project or program cost and schedule. Questions about why tunneling projects notoriously exceed budget numbers abound. Evaluations in retrospect and going forward have focused on the wide breadth of inherent risks associated with tunneling. More and more, these risks are being identified, studied and managed to a higher degree. As more and more scrutiny pervades the industry, little value is being obtained and leveraged on future projects. The industry seems to be headed in a direction of making the same mistakes over and over. The notion of risk evaluation has been around for decades and received wide notoriety with the U.S. Space Program and ambitious projects in the energy industry such as hydropower and nuclear power in the 1960s and 1970s (Stewart and Melcher, 1997). This led to the evolution of tunnel risk analyses with more rigorous identification of the unique risks in tunneling projects impacting cost and schedule. As tunneling risks became more readily identified, more attention has been paid to the frequency and impact of the occurrences unique to tunneling (ITIG, 2012). Currently, few tunnel projects are being planned, designed or constructed without a formal risk register that identifies the risks, mitigates the risks and quantifies the probable impacts of risks that cannot be mitigated. In hind sight on many recent projects, events that brought projects to “its knees” were not addressed in risk assessments or were not dealt with to adequately mitigate the risk of these events."

Jan 1, 2016

By R. Adsero

"In view of the decade long decline in worldwide mine equipment productivity and with heavy economic pressures and survival at risk, improvements for those remaining in the game are essential. The latest Multifactor Productivity data for the US mining industry indicates a continuing descent with Australia on a similar course. The world’s mining industry has a fleet of over 400 large draglines moving billions of tons of material annually. The most efficient use of this equipment resource will provide a competitive advantage to those companies who are committed to improving performance. A dragline monitoring system is a requirement for optimum operations. The monitor reports the facts. Focused actions can change the facts and create improved performance. Analyzing monitor data to build knowledge and create understanding is a beginning. Understanding the key productivity indicators for dragline operations and an effective benchmarking process are the basis for improvement. There is overwhelming evidence that adopting new technologies and concepts including AC drive technology can and will bring about a step change in dragline operating cost with improved production performance.STATE OF THE MINING INDUSTRY A high altitude review of the state of the mining industry provided by a study of multifactor productivity shows a continuation of lower and lower output year on year for the capital and labor inputs applied. The story is sadly similar for both U.S. mining and the Australian mining sector. In fact, according to PwC analysts the worlds mining equipment productivity has declined 20% over the past seven years. (Lumley, 2014) Although the reasons for the continuing decline in mining productivity are varied, the need for improvement is clear. The world’s mining industry fleet of well over 400 large draglines moves billions of tons of overburden and ore (phosphate, limestone, etc.) annually.This discussion will review a few of the tools available for improved productivity in dragline operations."

Jan 1, 2016

By V. O. Tenorio, P. P. V. Coronado

"INTRODUCTION Productivity in Open Pit mines depend on the observation and adjustment of critical phases of operation. As one of the most expensive activities in Open Pit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad-hoc methodology for analyzing the Key Performance Indicators (KPIs) involved in the production cycle, it is possible compare actual performance and ideal operating conditions and develop an alert system when operating conditions are sub-par with the expected production standards. STUDY OBJECTIVES The purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle or the time of completing production tasks is falling outside a predefined value. This alert is compared with pre-defined Key Performance Indicators (KPIs) and determine corrective actions: • Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process; • Demonstrate the utility of KPIs in the extraction of ore and waste, and how they help to identify equipment performance; • Develop software interfaces to visualize the Alert System in order to increase awareness in the operations supervisor; and • Make recommendations for future applications that can help improve the productive process of an Open Pit mine. PROBLEM STATEMENT Transporting material in Open Pit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity and subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded, and other delays. This creates inefficiencies in fuel consumption and energy utilization. For the identification of delays, a context-based system could be required in order to help optimizing the haulage cycle time by controlling delays in loading, haulage, and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2016

By V. Herman, B. Knorr, D. Whalen

"Edge effect is a condition widely observed in High Pressure Grinding Roll (HPGR) operations that gives rise to reduced comminution at the edges of the roll surfaces. This effect is caused by a reduction in the local crushing pressure at the edges of the rolls resulting from the sliding friction between the static cheek plates and HPGR feed material. Practically, this has an impact on equipment sizing, as the edge effect leads to coarser particles reporting to downstream equipment in open-circuit operations and increased circulating load and diminished HPGR circuit capacity in closed-circuit operations.To address this, Metso's HRC™ HPGR incorporates an Arch-frame to maintain a parallel relationship between the rolls and allow for the use of a flanged roll design. We conducted a series of pilot-plant tests with a 750 mm by 400 mm HRC HPGR to compare the performance of the flanged roll design against that of a traditional cheek plate arrangement under similar operating conditions. The edge effect was found to be significantly reduced with the flanged roll design. Based on the pilot-plant results, the implications for circuit design, energy efficiency and overall plant performance in a full-scale application were investigated and discussed.IntroductionGlobal trends such as lower ore grades and rising operating costs are driving the market toward more energy-efficient mineral processing solutions, most notably in comminution circuit design. High pressure grinding rolls (HPGRs) have been recognized as an energy-efficient solution relative to more conventional circuit designs. The basic operating principle of HPGRs, in which a fairly uniform pressure is applied to a bed of material in the compression zone, lends itself to this improved energy efficiency (Morley, 2006). Studies have estimated that savings of 10-15 percent are possible when comparing an HPGR circuit with a traditional SABC circuit (Rosario and Hall, 2008). While HPGRs offer a more energy-efficient solution than tumbling mills, there is still room for improvement in many aspects of the design. Edge effect, in particular, is one such aspect that limits the effectiveness of the machines. Edge effect is the impaired performance at the edge of the rolls due to a reduction in crushing pressure (Morley, 2010; van der Meer, 2010). As described in our prior work (Knorr, Herman and Whalen, 2013), edge effect is caused by the interaction between the ore entering the crusher and the relatively static cheek plates positioned at the edges of the rolls. As the material is drawn into the crushing zone, the sliding friction between the ore and the cheek plates inhibits the ability of material to be effectively drawn into the compression zone at the edges of the rolls. This reduces the crushing force in those edge regions relative to the center of the roll where material is being drawn into the compression zone at a higher rate. In addition, the cheek plates of a traditional HPGR design are held in place by spring-loaded brackets that are adjustable to manage the clearance. This spring-loaded cheek plate design prevents full compression of the material in the edge regions of the roll as there is relief at the outer edges."

Jan 1, 2016

By Hervé Le Bissonnais, Jean-Pierre Janin, Anne Bergère, Pierre Renier

"The most important impact on the environment of a tunnel excavation is the creation of surface settlements. Nowadays, the mechanized tunneling allows minimizing the settlements, applying a confinement pressure which counterbalances the ground de-confinement. It is thus essential to determine the correct amount of confinement pressure. In this paper, the authors present a 3D numerical study simulating the EPB-TBM excavation of a water tunnel, in the Flanders clays (north of France). Firstly, a simplified 3D simulation, based on the concept of instantaneous longitudinal settlement curve, was performed to predict the surface settlements for different values of heading confinement pressures. Secondly, the same pressures were tested by the EPB-TBM in a monitoring zone. The comparison between the prediction settlements and the measurements was very satisfactory and allowed validation of the numerical approach and the choice of the optimal confinement pressure value for a sensitive area of the project. INTRODUCTION The excavation of a tunnel can create displacements of the surrounding soil which may affect existing structures and generate unacceptable dysfunction. The development of the closed shield tunneling has permitted to reduce the volume loss generated around the excavation and consequently the surface settlements. In this case, as explained by different authors (Clough et al., 1985; Kastner et al., 1996; Mair and Taylor, 1997), the ground movements are influenced by the TBM works: the heading confinement pressure, the shield overcutting and conicity, the annular void grout injection parameters, the segment concrete lining rigidity, the consolidation of the grout. Hence, in the tunnel design, it is important to take into consideration these different processes of the excavation works to simulate correctly the tunneling process."

Jan 1, 2016

By D. A. Peacock

"INTRODUCTION Outer space technology and exploration have reached a tipping point so that mining and mineral processing in outer space is now a certainty and not a dream. Several competing companies, worldwide, are well on the way to building spaceships to land on the Moon and eventually mine the Moon and asteroids for volatiles, rare earth metals and Helium-3. The Google Lunar XPrize offers a $30 million prize1. China has recently landed a spacecraft on the Moon. The European Space Agency, with cooperation from the United States, has landed a spacecraft, Philae, on a comet. And, Mars One is planning a one-way trip to establish a settlement of humans on Mars. How and why are the Moon and asteroids and their resources of interest to private space industry and companies? Why are the Moon and asteroids viewed as a potential business venue? GEOLOGY OF THE MOON AND ASTEROIDS –WHY DO WE WANT TO MINE THERE? Space enterprises are actively working towards establishing and operating lunar and asteroid mining locations for resource extraction, resource processing, conversion to salable products, and distribution of the products and services in space and to Earth and beyond2. Forty-five years ago, the Apollo manned missions to the Moon returned rocks and regolith to Earth, which were studied and analyzed. What they found was that the Moon contains valuable minerals and resources. These minerals are largely due to meteor and asteroid impacts, which have, over eons, created this mineral rich regolith. These impacts have occurred on Earth as well, for billions of years, particularly early on in the history of the solar system. However, on Earth, wind, water, and vegetation have erased most of these impacts. On the Moon, in contrast, the only weathering is caused by subsequent impacts and the solar wind. The Moon regolith contains valuable rare earth minerals, platinum-group minerals (particularly where the Moon has been impacted by asteroids), volatiles (useful for processing and habitation), Helium-3 and titanium. Almost non-existent on earth, Helium-3 is abundant and accessible on the Moon and can be used in nuclear fusion power plants, producing much more energy than fission reactions and with much less radioactive waste. One of the main reasons Helium-3 is sought after as a fusion fuel is because there are no neutrons generated as a reaction product. Governments and private companies focus on mining of Helium-3 on the Moon as a basis for their economic models. Moon Express, one of the private companies who is planning on mining on the Moon, will recover moon rocks to fund its early operations25. Subsequently, it will recover Helium-3, platinum, and rare earth metals, as it engages in surface mining operations."

Jan 1, 2016

By S. K. Kawatra, J. E. D. McDonald, S. C. Roache

"The formation of geopolymers from mine tailings using cold-bonding processes is known to be possible. Numerous cold-bonding methods exist, but the hydrothermal processes involving high temperatures and pressures in the presence of steam have been found to be the most ideal. This paper presents the results of successful preliminary studies to apply hydrothermal bonding processes to mine tailings agglomerates. Particle-size analysis revealed the particle size of the tailings waste to be 80 percent passing at 35 µm. The compressive strengths of the tailings pellets were shown to increase with time in the curing vessel, closely approaching the 400 lbf of standard iron ore concentrate pellets. These strengths are sufficient to allow use of the tailings pellets as aggregate materials for asphalt and cement. Additional applications may be possible, including reprocessing to extract more valuable materials and usage as agglomerated road-bed materials, backfills for building foundations, and replacements for sand and lime in cement.IntroductionMine tailings are a waste byproduct of ore concentration and are available in large quantities across the world. Despite their abundance, they have received little attention or consideration for beneficial use. One reason is that the chemical nature of the material is not well known. Another factor that has hindered direct usage is the fine particle size. This raises the questions: what is the composition of the tailings, and how can such fine solids be beneficially used? Because the mining industry produces concentrates, the tailings may be treated as concentrates and processed in the same fashion, but it would be inefficient to consider full sintering or induration conditions for materials that have little ore content. To achieve sustainable operation, the development of technologies to use these tailings is necessary. Mine tailings should not be considered waste, and an “out of sight, out of mind” mentality does not represent a sustainable solution for the future.One iron ore mine in Michigan is estimated to have accumulated more than 400 million metric tons of tailings during its last 30 years of operation, with an additional 180 million metric tons accumulated before the ore body is depleted. These mine tailings currently have no practical use, largely due to a scarcity of knowledge of their true physiochemical nature. It is thought that lack of quality control of the waste material prevents its use, but variability in the unprocessed ore prevents a consistent waste stream composition. The fact that the tailings are available in such great quantities makes them an extremely attractive resource. However, developing a sustainable, low-cost means of repurposing the mine tailings waste as a construction material may only be completed once the tailings are physically and chemically understood. Due to the high silica content of the material studied, cold bonding was determined to be the most viable method for processing the tailings into a usable product."

Jan 1, 2016

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By M. S. Moats, A. Luyima, W. Cui

"Organic smoothing additives are used to produce dense, thick, high-quality cathodes in copper electrowinning. Glue had been used traditionally and is still used in operations that do not employ solvent extraction to produce the electrowinning electrolyte. With the advent of solvent extraction–electrowinning, guar started to be used and remained in use for many years as it does not affect the phase disengagement in solvent extraction. Recently, however, guar has been replaced by less-expensive saccharide- and polyacrylamide-based additives. This paper is the first of a series of four papers that examine saccharides and polyacrylamides as new additives for copper electrowinning. A review of previous research related to copper electrowinning additives is presented here, along with a selected review of additives in other copper electrodeposition systems.IntroductionThe recovery of copper from solution by electrowinning was first practiced in the early 1900s, but it was the combination of solvent extraction with electrowinning (SX-EW) in March 1968 at the Ranchers Bluebird Mine (Kordosky, 1992) that changed the landscape for the electrowinning process. Most copper electrowinning capacity is now associated with solvent extraction, though some copper is still won directly from leach solutions (Robinson et al., 2013). The ability to produce high-purity copper cathodes from SX-EW has taken the continued improvement of SX-EW technology over the past more than 40 years.One of the technologies that has seen improvement is that of the organic smoothing agents used during the electrodeposition of copper in the tankhouse. These organic additives are added to the acidic copper sulfate electrolyte during electrowinning to improve the smoothness, brightness and density of the copper cathodes. The organic additives that are presently in use are different from those used in 1999 (Jenkins et al., 1999). Over the past decade, many tankhouses have replaced the use of guar-based organic additives with those derived from other saccharides. Until now, there has been no comprehensive publication in the open literature on the behavior of these additives during copper electrowinning."

Jan 1, 2016

By M. Imazu, Ö. Aydan

"A new rock classification, Rock Mass Quality Rating (RMQR) proposed by the authors is briefly explained and its application for the design of tunnels and large underground openings support systems is described in this paper. RMQR is an index to evaluate the state of rock mass. The preliminary support design may be based on the concept to prevent structurally controlled failures of rock mass. RMQR can also evaluate the yielding characteristics of rock masses so that it is possible to design a support system to prevent or control the deformation of surrounding rock through the utilization of the proposed rock mass classification and some analytical and numerical techniques.INTRODUCTIONThe first three authors proposed a new rock classification system named Rock Mass Quality Rating (RMQR) (Aydan et al. 2014). RMQR quantifies the rock mass state, and using the classification system together with intrinsic geo-mechanical properties of intact rock, possible geo-mechanical properties of rock masses can be estimated. The instability modes of underground openings can be structurally controlled because of the orientation of discontinuities in rock mass and the in-situ stress induced (Aydan 1989; Aydan et al. 1993, 1996; Aydan and Genis, 2010). The authors (Aydan and Ulusay, 2013; Aydan, 2016) have also tried to apply this system to the design of a tunnel support system. The authors presented initial guidelines for the RMQR classification system earlier (Aydan and Ulusay, 2013).In this paper, the authors provide further guidelines and establish some criteria for support system design that considers loading conditions and types of underground structure according to RMQR. Guidelines are alsos proposed for selecting the proper size of rockbolts, rock anchors, shotcrete, steel ribs and concrete liner. These guidelines are based on past experiences with various underground structures, theoretical understanding and the anticipated behavior of rock mass under given in-situ stress conditions and excavation techniques. The authors also utilized some databases developed for large underground caverns and tunnels excavated in squeezing or rock-bursting ground conditions."

Jan 1, 2016