Search Documents

By Thomas J. Kuli, Tim Rape

When a fan or blower breaks down or becomes worn, customers have two choices. They can replace it or they can have it repaired. In the past, replacement was the preferred option, especially when the equipment was severely damaged or worn. Now, however, customers are discovering the benefits of repairing or rebuilding. Even when the cost of repair is more than 60 percent of the cost of a new fan, customers are choosing the repair option. The cost savings can range from 20 percent to 80 percent. In many cases, the quality of the repaired part or component will exceed the quality of the original. This is because repair engineers have an advantage over the original designers. They can see how the existing fan performed — or failed to perform — in a specific application.

Jan 1, 2005

By A. J. Friedrich

Conveyor belts are designed to go unnoticed. When they work well, they attract little attention. When they are not doing the job right, it is noticeable, and they need to be fixed immediately. Vulcanising contractors compete for the maintenance of belts in mining/quarrying and general materials handling worldwide. Damage repair is approached in similar fashion. The damaged section of belting is normally cut out and discarded, and the belt re-spliced using hot vulcanising, Cold splicing, or mechanical fasteners/clip joints. However, there is a cost-effective alternative, alleviating the need to remove damaged sections which are often perfectly recoverable. This is the use of cold-curing repair resins and adhesives.

Jan 1, 2000

By David Belknap, Clay Haynes, David Egger

Rehabilitation challenges were met nearly two months ahead of contract schedule for the Design-Build, Fast Track Scituate Aqueduct & Tunnel project in Cranston, Rhode Island. The aqueduct and tunnel were built in the 1920s and consisted of three sections—a 2.3 m diameter reinforced concrete section that extends approximately305 m before it transitions to a horseshoe-shaped 2.3 m wide by 2.1 m high cast-in-place concrete tunnel that continues for approximately 5.3 km until it transitions back to a 2.3 m circular section that extends approximately 1.9 km to the end of this project. Major repairs were required to assure sustained operation of this water supply tunnel.

Jan 1, 2005

By R. L. Keaton

Since the earliest days of mining, the job of digging coal out of the earth has been considered one of the world?s most dangerous occupations. From 1880 to 1910, mine explosions and other accidents claimed thousands of victims. In 1907 alone, over three thousand deaths occurred in U.S. coal mines. Public concern has prompted the passage of much needed safety legislation; from the creation of the U.S. Bureau of Mines in 1910, to the comprehensive laws of the Federal Mine Safety and Health Act of 1977. This type of legislation, along with the cooperation of industry, labor, and MSHA has contributed greatly in making mining safer and more healthful. Mining deaths and injuries have declined Significantly since those early days. However, even though this trend is positive, none of US can afford to look at the injury numbers and frequency rates and label them as acceptable.

Jan 1, 1988

By Henry J. Schwellenbach

The New York Trap Rock Corporation has four plants located along the Hudson River, all within 70 miles of New York City. The company produces crushed stone for use as construction aggregate, with a total annual production amounting to 6 million tons. The crushed stone is moved to markets in metropolitan New York, New Jersey and Long island areas by water transportation. There are daily deliveries of approximately 35 scowloads to the market area. Its customers are contractors with ready-mixed concrete and asphalt plants located on the water, where the aggregate is unloaded for its ultimate use. For a number of years capital equipment was replaced only when the current operating machinery was no longer serviceable, or when' a need was apparent for a different type of equipment. There was no particular regard for efficiency or for operating and maintenance costs. Such lack of system often resulted in the emergency purchase of equipment which was later found to be unsuitable for the job. A few years ago it became apparent that a systematic procedure was necessary. After evaluation of several systems, an individualized plan was evolved from the basic pattern developed by the Machinery and Allied Products Institute. The system adopted by New York Trap Rock has proved wholly satisfactory.

Jan 1, 1959

By Nick Hasenack

In the pelletizing plant of Hoogovens, Estel BV, a varying mixture of hematites and magnetites is used for the production of acid and (occasionally) fluxed pellets. Optimum results regarding productivity, quality and process control are obtained with mixtures containing 30-40 % magnetites. A decrease of the magnetite ratio or an increase of the basicity has a great influence on both productivity and heat and power consumption. Tests have been carried out to find the extent to which magnetite can be replaced by b.f. dust, mill-scale and coke breeze. Pilot plant tests show that about 80-100 % of the production loss due to a decrease in magnetite content or to the increase in basicity can be regained without damage to the quality by adding coke breeze. The amount of coke breeze should be limited tot 1,5 %; if this percen¬tage is chosen higher, the quality of the pellets deteriorates rapidly. The amount of coke breeze to be added should be about 30 % above the theoretical value, based on heat balance considerations. The results achieved by incorporating b.f. dust and mill-scale into the pelletmix were also encouraging, but as some types of mill-scale are very difficult to grind and the supply of b.f. dust is limited, the research has not been carried out extensively in this field. The pilot plant tests on replacement of magnetite by coke breeze have been followed by industrial tests, during which the breeze was added to the ore feed before the dry-grinding system.

Jan 1, 1977

By S. Makni, F. Wang, A. Rosa, B. Klein, C. Saud, R. McIvor, A. Kumar, C. Gagnon, D. Gong

In response to the Natural Resources Canada “Crush It Challenge”, Corem partnered with the University of British Columbia and led a project to develop and demonstrate the use of high-pressure grinding to replace the workhorse of the industry, wet ball milling, with high-pressure grinding. Two plant case studies, a small tonnage gold recovery operation, and a large tonnage copper recovery operation, were carried out. Plant circuit performances were compared to pilot plants operated on the same circuit feed set up to represent the novel equipment and flowsheet that was developed to produce separation circuit feed. Numerous obstacles to industrial implementation of highpressure grinding in this role which were recognized at the outset of the work were successfully addressed. In both cases, comminution equipment energy savings alone, and final stage total circuit energy savings, exceeded 60% and 50%, respectively. Downstream mineral separation performance was the same or better.

Mar 2, 2022

By Robert McIvor, Sami Makni, Andreia Rosa, Claude Gagnon

In response to the Natural Resources Canada “Crush It Challenge,” Corem partnered with the University of British Columbia and led a project to develop and demonstrate the use of high-pressure grinding to replace the workhorse of the industry, wet ball milling. Two plant case studies, a small tonnage gold recovery operation and a large tonnage copper recovery operation, were carried out. Plant circuit performances were compared to pilot plants operated on the same circuit feed setup to represent the novel equipment and flowsheet that was developed to produce separation circuit feed. Numerous obstacles to industrial implementation of high-pressure grinding in this role which were recognized at the outset of the work were successfully addressed. In both cases, comminution equipment energy savings alone and final stage total circuit energy savings exceeded 60% and 50%, respectively. Downstream mineral separation performance was the same or better.

Nov 28, 2023

By Zhian Liang, Xiong Huang, Weixin Wu, Lifeng Cui, Zhuanhua Wei, Guoyao Li, Xiao Ni, Junrong Wang, Shuiping Zhong

ZJ 201 (modified starch) is a non-toxic, odorless, and biodegradable polymeric depressant, which selectively depressed galena in batch flotation tests while chalcopyrite was not significantly affected. In a plant trial, copper-lead separation was successful for the first time without using dichromate. Moreover, the plant process could be changed to sequential Cu-Pb flotation using ZJ 201 for higher grade lead concentrate. A copper concentrate was obtained with a Cu grade of 24.91% and a Pb grade of 5.11%, which recovered 76.6% of the copper from the original ore; a lead concentrate was also obtained with a Pb grade of 21.90% and a Cu grade of 5.31%, which recovered 52.6% of the lead. In addition to the effective copper-lead separation observed in the plant trial, another improvement observed is that gold was recovered mostly in copper concentrate, which could be sold for higher prices. Au grade reached 230.64 g/t, and its recovery reached 65.8% in the copper concentrate. Au grade in lead concentrate was only 18.90 g/t.

Aug 27, 2021

By Jim Owens

The methodology of quarrying changed significantly in the Indiana limestone industry in the 60 years between Sept. 11, 1941 and Sept. 11, 2001. The former was the date of the Pentagon groundbreaking ceremony, while the latter was when the building was damaged by American Airlines Flight 77. So too, though to a lesser degree, did the machinery and methods used to fabricate the stone. The rededication ceremony on Sept. 11, 2002 marked the end of the Phoenix Project, as the rebuilding effort was named. The story of this remarkable project illustrates what the American construction(and Indiana limestone) industry can accomplish when working toward a common goal.

Jan 1, 2005

By Alberto Tarsitani

The existing Rome-Florence railroad capacity is inadequate for the traffic volume. To increase this capacity and to reduce the traveling time the Italian National Railroad Administration has decided to provide an additional 400% of rail capacity. This new rail line will be known as the Direttissima Roma-Florence line. It is planned to operate the trains on this connection at speeds of 250 km per hr. Table 1 lists the main design characteristics. [TABLE 1. Design Characteristics Design speed250 km per hr Maximum inclination80 00 (0.8%) Minimum curve radius3000 m Minimum vertical curve radius30,000 m Maximum superelevation in curve 425 mm Type of rail60 kg per m welded] The new rail line will be connected to the existing one by means of high speed switches called "interconnections" so that parts of the new line can be used also by local trains. Construction works for this new line have been divided by the railroad administration into eight sections. Five of these have already been committed to joint ventures. Castiglione Tunnel is a part of the fifth section, 42 km in length, which has been awarded to Consorzio Ferrofir which is a joint venture composed of the construction firms of Astaldi - Di Penta - Lodigiani - Sogene.

Jan 1, 1974

By C. C. Clark

The National Institute for Occupational Safety and Health (NIOSH), Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system there is a need to know when the material has developed a threshold early compressive strength of approximately 1 MPa (145 psi) for safe re-entry of miner and machine into shotcreted mine workings. This equates to the material having developed enough strength to be self-supporting and allow for emplacement of the remaining support elements that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on-site in the first six hours after application using the ASTM C 116-90 (1990) standard. These advances were demonstrated in tests on five commercially available shotcrete mixes, sprayed as dry shotcrete using the field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. The findings of this NIOSH research for determining shotcrete early strength can improve mine safety by providing a method for determining initial site specific material property values to be used for design and as a means to conduct on-site quality control and monitoring during production.

Jan 1, 2010

By D. C. Willett

INTRODUCTION The Symposium on the Development of Underground Space, held in Seattle, Washington, from October 1 through 3, 1980, was organized by the "Deep Space" subcommittee of the ASCE's Underground Research Technology Council. The primary objective of the symposium was the exploration of the interfaces between the investigation, design and construction of large underground facilities in "deep space" which, for the purposes of the committee, has been defined as starting at 100m below ground surface. The meeting focussed primarily on tunnels, caverns and shafts in hard rock; the meeting format comprised a number of brief presentations concerned with the technical aspects of investigation, design and construction, followed by an open discussion, and concluded with the assembly of recommendations regarding the interface problem by the symposium participants. The principal considerations brought out during the symposium, and a general review of the conclusions, are briefly presented in the following paragraphs. INVESTIGATION The sessions dealing with "Investigation" were chaired by Dr. H. Pratt. Presentations were made by Dr. D.C. Banks, Dr. W.A. Hustrulid and Dr. Pratt. The extent of the interface of the investigation phase with the other (design and construction) phases of an underground facility will depend in large measure upon the nature of the facility; at one end of the spectrum, the investigation must be in continuous and closely coupled relationship with the design of a radwaste facility. At the other end of the spectrum, for (say) a small mining operation, the interface is largely associated with the initial development, with only minor on-going involvement.

Jan 1, 1981

Engineering programs usually do not provide sufficient opportunities for students to develop written communication skills. The responsibility for developing those skills is frequently delegated to the humanities faculty, who in a single technical writing course are supposed to transform engineering students into proficient communicators. A general template which was developed for report writing in our senior level capstone design courses is discussed. Students have improved their writing skills by using the template. The writing assignments have provided the students the opportunity to write and revise more technical reports that communicate their design.

Jan 1, 1995

By Gordon P. Riddler

IMMM Reporting Code 2001 – Some Developments -General definition of a Competent Person -Rules of Conduct with Guidelines -Table of Generic Terms with Guidelines -More specific to non-metallic minerals -Word ‘ore’ is not used for reserve/resource categories -More definitive on Mineral Exploration Results

Jan 1, 2003

By Michael Bourassa, Sonja Felderhof, Normand Champigny, Steve Vaughan

Introduction -Comparison of International Reporting Standards (Sonja) -Legal and Due Diligence Requirements for Reporting (Steve) -Flexibility to Recognize International Reporting Standards (Michael) -Obligation of SRO’s to Discipline (Michael) -Impact of Sarbanes Oxley on Reporting (Normand)

Jan 1, 2003

At present, increasing focus of public perception is placed on the environmental and social benefits, risks and impacts of metals and metal-bearing products. To address these issues, the concept of product stewardship has recently been introduced into the political debate. In this paper, results from a survey of existing environmental and social reporting practice in the copper mining, smelting, refining and fabricating industry are presented. In this context, particular emphasis is placed on the reporting practice regarding products and product performance over the life cycle. In a few companies there has recently been a shift towards adopting product stewardship principles and putting them into action. As part of an ongoing exercise within the Non-Ferrous Consultative Forum on Sustainable Development sponsored by the International Copper Study Group (ICSG) key issues of interest to the non-ferrous metals sector are being addressed. The Forum, for example, has developed a series of principles, criteria and indicators that could form the basis for a voluntary, industry-lead product stewardship scheme. Current achievements and way forward of this product stewardship initiative will be presented.

Jan 1, 2003

By L. A. Rapoport

This paper outlines the methodology and results pertaining to the simulation of the U.S. coal industry in the context of an integrated, time-dynamic model of Long-Range Energy Developments and Supplies (LORENDAS). By way of background we will present first an overview of the overall LORENDAS model structure. We will, then, outline the characteristics of the formulation and data used for the representation of the U.S. coal industry. Finally, a series of model results will be reviewed, with particular emphasis on the long term projections of coal production and distribution under different basic economic and/or political scenarios.

Jan 1, 1977

Compagnie Miniere Esperance (CME), a mining company based in French Guyana, operates a gold primary ore body in open pit. The ore is processed through crushing, grinding and gravity separation. Tailings are stored in a ?fine? pond. Analyses of the fine ponds proved a residual gold grade sufficient for a chemical treatment. However, direct cyanidation would require a too large installation, regarding the local conditions (accessibility, supplying and rainforest meteorological conditions). It has been then decided to test the feasibility of a pre-concentration using flotation. Lab tests have been carried out by SGS Lakefield (Canada) in March 2007, which proves the technical feasibility. Therefore, CME asked Caspeo to: ? Carry out an on-site flotation pilot campaign. ? Design an industrial flotation circuit. The tailings reprocessing will contribute to a better tailings management and a dry up of the gold resource, limiting the risk of illegal mining after remediation of the CME site. CME MINE The Esperance gold mine is located in French Guyana, in the vicinity of several gold deposits as Omaï, Rosebel or Camp Caïman, holded by Iamgold and Newmont. These main gold deposits are located on the figure 1. Esperance was put into operation in the early 90?s. The first years were devoted to the mining of alluvial gold in the gravel of the Esperance Creek. Since then, operation was led in the primary gold deposit. Annual production is on average 254kg for a total production in fifteen years of 4300kg. Geology Esperance deposit is located in the greenstone belt of the Guyana Shield. Mineralization is in tectonic contact between sedimentary basin of Maroni and a granitic massif. Clastic series, composed of conglomerate and lamina sandstone, overlie a volcano-sedimentary basement (series called "Paramaca"). The area is strongly folded by shear movements, resulting from granite deposit. Gold is in interlacing quartz veins intersecting the clastic series. Gold is present in association with pyrite. Other elements, as silver or arsenic, are in negligible quantity. Exploitation The Maroni River is the only access to the Esperance mine. Only the saprolite and a part of the transition rock are extracted in the open pit. Excavation works are done using shovels Hyundai 450 (4 units) and haulage works using articulated dumpers Terex TA35 (4 units). These two sorts of equipments are presented figure 2. Mill The mill is composed of crushing and grinding processing plants. After gravity concentration, both plants produce tailings that are stored in two ponds: the first pond contains coarse product which segregates the particles crushed to 2mm upstream and settled clays downstream; the second pond contains the fine product made of particles ground to 200µm. These two ponds, bordered by dams and diversion canals, are located on former alluvial sites of Esperance Creek (see figure 3). [ ] The CME mill is currently producing gold concentrate, with a global recovery of about 67%. The ore is crushed by one jaw crusher and two hammer crushers. The ore then passes through a Knelson KC 48 gravity concentrator, producing a first gold concentrate. The

Jan 1, 2009

Compagnie Minière Espérance mines a primary gold orebody in an openpit. The ore is processed through crushing, primary gravity concentration, grinding and secondary gravity separation, generating tailings with remaining fine gold. Analysis of the material in the pond has indicated a residual gold grade sufficient to justify a chemical treatment process to recover the gold. However, direct cyanidation would require a prohibitively large installation for the site, which is located in a remote rainforest environment. It was decided to test the feasibility of preconcentration using flotation. As lab tests proved up the technical feasibility of the flotation process, an on-site pilot operation was carried out to assess the continuous circuit performances, define the best configuration and obtain enough data for industrial circuit sizing. Data collected during the pilot campaign was used for calibrating a process simulator built with the USIM? PAC software. The simulator validated the feasibility of upgrading the existing plant, including the reprocessing of tailings to obtain an acceptable fine gold recovery from a small amount of concentrate.

Jan 1, 2010