Search Documents

By Dr. Richard F. Coon, James D. Mavis

Risks and abatements associated with preliminary reconnaissance, plugging and filling, and maintenance of perched mine water pool are examined. This case history showed that the initial appeal of portal plugging was replaced by concern over potential environmental hazards when details of implementation were investigated.

Jan 1, 1992

By S. R. Abt, J. D. Nelson, G. M. Smith

An empirical investigation was conducted to formulate a design criteria for predicting the beach profile of hydraulically deposited tailings. Field data were obtained from mining operations producing gold sulfides, silver, molybdenum, copper, platinum, and uranium. Site-specific parameters were collected that included the beach slopes, tailings soil properties, slurry properties, and the slurry distribution system characteristics. Each of the beach profiles were dimensionlessly plotted, and regression expressions were computed. It was determined that either a power expression or exponential expression closely predicted each beach slope. A general power expression and a general exponential ex¬pression were developed resulting in a design criteria. A procedure was formulated to determine which expression, power or exponential, is applicable to any specific site. A slope designation chart was developed as a function of the discharge, the tailings critical tractive shear stress, and the inertial forces exerted by the slurry on the beach.

Jan 1, 1987

By Robert A. Bauer

Two basic types of subsidence occur in Illinois: pit and sag / trough. Pits develop over mines less than 165 feet deep and where relatively incompetent strata are found over the mines. Sag subsidence is found over mines as shallow as 75 feet and more generally over mines of greater depths. The percentage of subsidence and angles of draw associated with sag subsidence appear to be controlled by the rock properties at each specific site. The percentage of subsidence and angles of draw are smaller where the sites are not affected by geologic structures. An investigation to determine if a time factor based on the time interval from the date of mining to the subsidence events has shown that simple correlations with time, percent extraction, average pillar stresses, and pillar dimensions is not evident in Illinois.

Jan 1, 1982

By O. A. Bascur

The problem of setting the proper control objectives and/or having several objectives to be met in the implementation of grinding control strategies can be resolved. The design and implementation of a distributed control system for safe operation of a grinding circuit while maximizing profit is presented. An optimal recovery through- put target for a desired grind is accomplished by advanced control strategies at the DCS level. A mill load constraint control technique provides stable operation with a substantial increase in throughput, while the desired grind index is maintained by an inferential grind control technique without using a particle size analyzer. The integration of crushing/grinding and flotation in the overall design was the key to the success of the project. This synergistic effect was obtained by implementing a computer plant management system in the concentrator. The overall/philosophy was to keep the implementation simple while using new technology creatively.

Jan 1, 1991

By D. Rajkovic

Geothermal sources are exploited in two basic forms, i.e., the primary form of thermal energy and that converted into electrical energy by using an adequate thermodynamic cycle. There is a possibility of applying several processes for the conversion of thermal into mechanical or electrical energy, which depend on the thermodynamic characteristics of the geothermal water. Geothermal sources in Croatia do not contain steam of relatively high temperature, like in Italy, although both countries are nearly in the same position with respect to geothermal belt. Geothermal sources in Croatia are mostly so-called low-temperature geothermal sources with water temperatures lower than 100°C (Cubric and Jelic, 1993). A few of them have been exploited, although the percentage of utilization of their available power is still very small. The low-temperature potential is a major disadvantage when it comes to power generation, since state-of-the-art geothermal power plants require reheated steam or hot water to operate. There is a common belief that the optimum way of exploiting low-temperature geothermal sources is heat generation. Therefore, this analysis is especially aimed at potential users and showing the technical and economical possibilities of using low-temperature sources for conversion of thermal energy into mechanical work and electrical energy.

Jan 1, 2003

By P. I. James, M. R. Baker

This paper examines new copper production from waste-grade ore using Blue Planet Strategies’ DEMET™ (Dynamic Electrode Mining Effluent Treatment) technology, which aims to bridge the practical weak pregnant leach solution (PLS) processing gap in heap leach-solvent extraction/electrowinning (SX/EW) operations by electrochemically removing metals from weak streams and generating product streams strengthened in target metals in a functional analog to SX. Weak PLS treatment was studied and used to estimate the economic and production impacts for a representative hypothetical brownfield copper heap leaching and DEMET-augmented SX/ EW operation to utilize "waste ore." Copper removal at 86% plating efficiency to below 0.1 g/L copper with power consumption of 0.55 kWh/lb copper and product strengths of over 10 g/L copper are presented. Modeling yielded approximately $2/lb total copper production and = $1/lb treatment costs with an immediate operation gross margin increase of 12% for the augmented brownfield. Potential mine life extension with an average 38% gross margin on "waste ore" augmented production at copper values of $3.25/lb was also indicated.

Jan 1, 2014

By P. I. James, M. R. Baker

Este artículo analiza la nueva producción de cobre a partir de "minerales de desecho" de baja ley usando la tecnología de Blue Planet Strategies DEMET™ (Dynamic Electrode Mining Effluent Treatment, por sus siglas en inglés), que tiene como objetivo salvar la brecha de procesamiento entre la solución débil de lixiviación en operaciones de extracción por solventes/electrowinning (SX/EW), removiendo electroquímicamente los metales a partir de corrientes débiles y a la vez generando productos concentrados en metales objetivo en un análogo funcional de extracción por solventes (SX). Se estudió el tratamiento de la débil solución de lixiviación pregnant (PLS por sus siglas en inglés) y se usó para estimar los impactos económicos y de producción para una hipotética lixiviación en pilas de cobre brownfield y una operación aumentada DEMET usando SX/EW para tratar el "mineral de desecho." Se presenta la remoción de cobre a un 86% de eficiencia en las placas por debajo de 0,1 g/L de cobre con un consumo de energía de 0.55 kWh/lb de cobre y una concentración del producto mayor a 10 g Cu/L. El modelamiento arrojó aproximadamente $2/ lb para la producción total de cobre y costos de tratamiento menores o iguales a $1/lb con un inmediato aumento del margen bruto de operación del 12% para el brownfield incrementado. Se indicó también un aumento de la vida de la mina con un margen bruto promedio de 38% en la producción aumentada de "mineral de desecho" con valores de cobre de $3.25/lb.

Jan 1, 2014

By Heinz Hofmann

In order to drive tunnels with low overburden in town regions, it is necessary to give a quantitative prognosis for the deformation of the underground as well as of the tunnel-lining and of its stability. These problems and their solutions are illustrated by the works for a two-track-railway-tunnel in Bochum (Ruhrdistrict). In this case the most important problems consisted in passing below buildings in a vertical distance to the fundamentals of only 3.20 m and a railway earthdam with rapid train traffic in a distance of 4 m under the dam. The results of measurements from other comparable tunnels and finite-element-computations were used to prognose the settlements on the surface and in the ground, their distributions and their development in time. To obtain these values at the site, a special system of tunnel driving was executed. The tunnel was excavated with the newest type of tunneling-machine from DEMAG, cutting an inclined front, immediately followed by a special temporary support of shotcrete and inclined steel-ribs. By using theoretical and empirical methods to assess the behavior of the tunnel and underground and by executing an optimal driving system in technical as well as economical aspects, the expected behavior, expressed in quantitative values, was almost equivalent to those received by control measurements.

Jan 1, 1974

By Dilip I. Patel, Jesus Schabib, W. Allen Mawr, Daniel A. Louis

East Side Access (ESA) will extend Long Island Rail Road into midtown Manhattan via 11 km of tunnels, a new terminal station and associated rail support facilities. The hard-rock tunneling in Manhattan will traverse under Park Avenue and some of the most historically and commercially significant real estate in the world. The soft-ground tunneling in Queens will traverse beneath Amtrak’s Sunnyside Yard and the Harold Inter locking, the busiest rail interlocking in North America. This paper details ESA’s program-wide geo-instrumentation monitoring system for obtaining, processing and presenting all geotechnical monitoring data. Data streams will be real-time, such as from automated total stations, and manually read, such as from optical survey instruments and handheld data loggers. All data will be input into a web-based Geo-Instrumentation Data Management System, which will be accessible to project stake holders via ESA’s intranet or via the Internet using remote access controls.

Jan 1, 2007

By F. Robert Hollo

Programmable controllers have achieved remarkable acceptance over the relatively few years since their introduction. They provide some unique advantages over conventional relay and solid-state logic, which they often replace. Programmable controllers are discussed in both conceptual and functional terms, followed by an exploration of their applicability to material handling tasks with particular emphasis on conveyor systems.

Jan 1, 1973

By Jean-Luc Cornet

As modern conveyors are increasing in size and complexity, their control requirements are becoming more and more critical. In addition to the safety and equipment protection requirements, control systems are now called to implement intelligent drive controls derived from dynamic analysis modelling, as well as to provide fast and accurate diagnostics while keeping operator controls simple. These requirements led to the development of a new and innovative approach to control system development. This paper describes the control philosophy used by Conveyor Dynamics, Inc. (CDI) and some of the key features of our approach to the architecture of control systems.

Jan 1, 1993

By Mike Horn, Keith Meade, Marvin L. Smallwood

Technological changes in programmable logic controllers (PLC)'s and the need to improve the architecture of Mine Wide Monitoring Systems (MWMS) has resulted in the design of a PLC based system at the Virginia Division of Island Creek Coal Company. The system which is presently in the installation phase, is a joint effort of Island Creek Coal Company, Westinghouse Electric Supply Company and Mining Controls Incorporated. The system uses an ethernet based network for graphic display of system data operating under the Genesis software package. Telemetry for the system utilizes the Seimens/Westinghouse L1 network operating over two twisted pairs. Remote telemetry uses fiber optic links and modems operating over standard telephone lines. 500 and 2000 series PLC's provide distributed data processing for the system with hierarchial processing operating under the Genesis software on the ethernet network for individual mine site monitoring along with the remotely located division office monitoring. System control and data acquisition is provided for underground MWMS operations and on the surface for a vast methane gathering system that is used for degasification of the mines and collection of pure methane for sale to the Columbia Gas Company as natural gas. The inability of industrial MWMS companies to keep up with the vast changes in technology, along with economic considerations associated with expanding the existing MWMS created the need for the development of the PLC based system to replace the older industrial monitoring systems.

Jan 1, 1993

By William J. Bryson

Just picture, if you will, the hot, lonely and desolate Ochre Mountains west of Salt Lake City. There works a grizzled old miner, his boots worn down, his clothes hang on a body stooped by years of hard labor. His skin is wrinkled and leather toughened by many years in the hot desert sun. His ever faithful burro stands patiently in the shade of a large rock as the tired old miner examines ore samples just acquired that very morning. Suddenly the old man's eyes widen, his breathing becomes rapid. 'Leaping to his feet, with a gleam in his eye, he cries, "Eureka, I'm rich, I've found the mother lode. This is where I will start my digging. " Without warning, the silent wilderness is alive with wild, shouting, charging figures! Frightened the old miner glances about him wide-eyed and pan- icky. His heart sinks, dismayed he now knows all is lost, this is the end. For there leaping from behind rocks and brush papers in hand, are the men from the Department of Interior, Bureau of Land Management, State Mine Inspectors, OSHA, MESA, EPA, OEO, and the never ending list of regulatory bodies related to todays mining industry.

Jan 1, 1975

By Takahide Wakamatsu, Junji Shibata

Complex polymetallic sulfide ore deposits occur in Tohoku district, northern part of Honshu island, Japan. The ore is locally called "Kuroko” ( black ore ) and is compactly composed of fine grained sulfide minerals of such principal metals as copper, lead, zinc and iron. Currently one of Kuroko mill plants is producing such concentrates as copper, lead, zinc, pyrite, barite, and clay minerals, mainly employing differential flotation techniques. This paper describes briefly the progress of techniques in Kuroko processing over the past thirty years and also the present state of Kuroko processing and its challenges to be studied and overcome in the future.

Jan 1, 1989

By G. H. Gronhovd

The U.S. Geological Survey estimate of the total remaining reserves of lignite in this country as of Jan. 1, 1967 was about 448 billion tons. This represents 27 percent of the total coal reserves on a tonnage basis and about 17 percent on a thermal basis. Approximately 98 percent of these reserves are in a vast lignite field located in western North Dakota and eastern Montana. This field also extends north into the Canadian province of Saskatchewan. Despite these large reserves and relative ease of mining by stripping operations, lignite production historically has accounted for less than 1 percent of the national total. This is largely due to the fact that the lignite deposits are located in an area that has no large centers of population and the economical radius of transportation is limited by its relatively high moisture and low heating value. Commercial utilization of North Dakota lignite for power production became firmly established in the mid-1920's with the development of the first successful lignite-burning equipment. Most of the early lignite-fired boilers were equipped with spreader stokers, but as the size of the plants increased, pulverized-coal firing became the more popular method, and with few exceptions, the plants built during the past 15 years are pc-fired.

Jan 1, 1968

By E. M. Wilde

Through the USGS's National Coal Availability program, coal resource appraisals have been completed for three 7.5-minute quadrangles (Willow Crossing, Colstrip East, Colstrip SW) in the Powder River Basin area of southeastern Montana. Available coal reserves (original reserves minus tonnages affected by current restrictions) vary from 44 to 70 percent of the original reserves. Major restrictions impacting each area also vary. In each area, one or two beds contain most of the reserves, but up to eleven beds contain available coal. The main beds in completed studies are the Knobloch, Rosebud, Sawyer and Flowers-Goodale. Three additional areas (six 7.5-minute quadrangles) are in preparation.

Jan 1, 2001

By H. R. Cooper

Refinements and increased sophistication in modeling and simulation, and introduction of advanced techniques in automatic control made feasible with digital processor handling of data, represent the most significant fields of advancement during the past ten years. Extensions in capability to predict performance of beneficiation and other mineral extraction techniques now provide powerful assistance to developers and and designers of minerals processing unit operations and complete plant flowsheets. Computer aided advances are categorized by work in the following fields: - Steady state modeling and simulation of processes - Dynamic modeling and simulation of processes - Optimization methodology in crushing, grinding, and flotation - Optimal process control methods - Expert systems in process control

Jan 1, 1989

By R. Jerez

This paper describes practical applications of lineal" programming techniques to help in the planning of production, transportation and shipments at different coal mines. The models are being used by Cyprus Coal Company in eastern and western operations to plan coal production, economic dispatching and blending over variable time horizons. In addition, where a preparation plant exists, the models establish the amount of washing required to meet specific coal sales qualities. The emphasis on this paper is on model development and implementation together with a system to track coal flow and qualities, either raw from the mines to the loading facilities 01" processed through a preparation plant.

Jan 1, 1991

By E. P. Reed

We are proud that one of our predecessor companies originated the phrase "Safety First". That phrase remains today as the guiding principle that governs our total approach to safety and well being in U. S. Steel. U. S. Steel management is totally committed to this attitude and our objective is to have every employee as deeply conscious of his safety responsibilities. Safety is a state of mind but like most things it must have a physical side - both intertwined and inseparable. You might say each promotes the other; and this gives us confidence that with hard work, cooperation from all individuals, and proper application of knowledge and experience, our ultimate objective of frequency "0" will be attained. It is in this vein of thought we present a paper today which gives you briefly our progress, mainly in the physical, or mechanical, protection of miners at work in the Southern District mining operations of U. S. Steel. The Southern District not only includes the underground mining of coal but the underground mining of zinc ore in Jefferson City, Tennessee, and the quarrying of dolomitic limestone near Bessemer, Alabama.

Jan 1, 1970

This paper discusses the type of scaling operations presently in use in underground mines. It defines a scaling factor that is expressed as the area necessary to scale to extract 1 t (1.1 st) of ore. The problems associated with conventional scaling methods are discussed as well as recent developments in mechanized hand-held scaling de- vices and methods of loose detection. The elements of the scaling process are further analyzed. The conception and design of a mechanized scaling device, developed at Universite' Laval is also described. The results of field tests conducted in Quebec hard rock mines are presented. The experimental findings show that the mechanized hand-held scaling device shows potential in improving the productivity and safety of underground mining operations.

Jan 1, 1996