Search Documents

By C. D. Litton

This paper describes two new gas diagnostic techniques which have been used successfully to determine: 1) the combustion status of underground mines which have been sealed due to fire (Littol1 Ratio); and 2) the location of fires in abandoned, underground mines or waste banks (Kim Ratio). The Litton Ratio makes use of the rate of change of CO, calculated on both an air-free and methane-free basis, from mine gas samples and compares these values with those expected from a normal, combustion-free environment. The Kim Ratio uses the concentrations of total hydrocarbons, C2 ?C5, less the methane, to arrive at ratio values which increase as combustion intensity increases. The details of these two new techniques, their application to real situations, and their limitations will be discussed.

Jan 1, 1989

By G. T. Lineberry, R. Q. Honaker

Coal extraction typically results in the recovery of pure rock that ranges from small to very large quantities depending on seam thickness and other characteristics. The removal of pure rock may allow the recovery of three times the amount in middling coal particles, which has significant economical benefits. In an industrial example, a 150% increase in revenue was realized from deshaling a low-ash, run-of-mine coal and blending with a processed clean coal product. Deshaling is the process of removing pure rock from coal, which normally involves a high-density separation in a gravity-based process. The removal of the relatively pure rock near the point of extraction has the potential to further enhance the economics of an operation due to reduced materials handling and refuse storage costs.

Jan 1, 2004

By Albert J. Shohet

The increasing scarcity of bentonite coupled with the potential of improved pellet strength have created a need for understanding the effects of thorough bentonite dispersion in taconite concentrate. It has been known for more than a decade that under certain conditions substantial savings of bentonite are realizable by using thorough mixing of bentonite as compared to poor mixing. Extensive work done by J. O. Zetterstrom l at the Univer¬sity of Minnesota indicated the effect of thorough bentonite mixing in a controlled laboratory testing. Commercial hardware was not available at the time Zetterstrom1 paper was published and not much work was done until R. L. Stone, J. M. Karpinsky2, did work with Muller mixing. Nabush 3 worked with the pugmill principle, and Hoogovens 4 and Robe River 5 used the fluidized bed principle. It was very hard to convince iron ore industries to improve the mixing of Bentonite and taconite for the following reasons: A. The initial capital investment for improved mixing equipment; B. The relatively low bentonite cost a few years back, which was not enough to justify new equip¬ment investment;

Jan 1, 1976

By Wei Luo

Nickeliferous laterites were characterized by particle size analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDX), Fourier transform infrared (FTIR) spectroscopy and thermal analysis. Results showed that the laterites consist mainly of nickel-substituted lizardite with cobble-like morphology and traces amounts of magnetite and phlogopite. As fluoride ions can react with silicon in the lizardite crystal structure and form metal-fluoride complexes, as well as increase the equilibrium constant of the lizardite dissolution in acid solution dramatically, the addition of minor fluoride salts (0.2wt.% NaF) gave a markedly enhanced metal extraction rate (Ni 81.7% and Co 52.3%) under the experi-mental conditions of particle size d50= 25 µm, 10% (v/v) H2SO4, reaction time 2 h, reaction temperature 90°C, liquid-to-solid ratio 3 mL g-1 and stirring at 500 rpm compared with H2SO4 alone (Ni 69.6% and Co 30.8%).

Jan 1, 2010

By Ning Liu, Xuming Wang, Yongqiang Lu, Jan D. Miller

Bench-scale flotation experiments have been conducted to study the effect of nonionic polyethylene oxide (PEO) polymer surfactants on the flotation of Florida phosphate rock. It has been found that PEOs having a molecular weight from 1,200 to 8,000 are effective. Flotation results demonstrate that the addition of nonionic PEO has a favorable effect on phosphate flotation, especially on the flotation of coarse phosphate feed. At about the same collector level, phosphate recovery can be improved by 10-30% with PEO addition. The surface chemistry of phosphate flotation using the fatty acid/fuel oil/PEO system has also been studied to better understand the phenomena involved. The increase in phosphate recovery with PEO addition has been attributed to improved dispersion of fatty acid, which leads to better froth stability and a more hydrophobic surface state.

Jan 1, 1999

By Ivan Hunter, Gary Johnson

In many comminution circuits based on SAG mills, an operating cost penalty is incurred in terms of high unit power consumption. By the addition of a crusher to the circuit, to crush part of the so­called critical size fraction extracted from the mill charge, the power efficiency of the circuit can be significantly improved. Dominion Mining has now incorporated pebble crushing into three of its comminution circuits. The improvements in circuit performance have in all cases been significant, and in some cases dramatic.

Jan 1, 1991

By Steve Kral

After years of cutbacks, closures and layoffs, the mining industry is beginning to expand again. Metals prices are up and so is investor interest and confidence in the industry. Gold prices began to slowly move up in January2003 and finally cracked the $12.86/g ($400/oz) mark in early December. Silver, too, is up, as is copper. So the mining industry is feeling good about itself again and many companies are expanding existing mines and developing new ones. One side benefit to mining’s improved outlook is that companies are beginning to send more of their employees to industry conferences. Such was the case at the109th Northwest Mining Association meeting in Spokane, WA. The meeting was held in early December and attracted 1,100 attendees and 84 exhibiting companies. That is up from 2002’s attendance of about 900 people and 65 exhibitors. The theme was “A Partnership into the Future.”

Jan 1, 2004

By D. Hopkins, D. Türler, R. D. Giauque, W. B. Davis, M. Karaca

In a highly collaborative research and development project with mining and university partners, sensors and data-analysis tools are being developed for rock-mass characterization and real-time measurement of mineral content. Determining mineralogy prior to mucking in an open-pit mine is important for routing the material to the appropriate processing stream. A possible alternative to lab assay of dust and cuttings obtained from drill holes is continuous on-line sampling and real-time x-ray fluorescence (XRF) spectroscopy. Results presented demonstrate that statistical analyses combined with XRF data can be employed to identify minerals and, possibly, different rock types. The objective is to create a detailed three-dimensional mineralogical map in real time that would improve downstream process efficiency.

Jan 1, 2002

By G. Henry, S. J. Domvile

Arsenic management practices at the Con Mine in Yellowknife, Northwest Territories have evolved over the last fifty years of operations under changing regulatory, economic and technological conditions and incentives. As a result of a processing upset in the mine' s arsenic trioxide reclamation plant circuit in August 1988, arsenic levels in the mine' s tailings pond rose from 30 to over 100 mg V. At these arsenic levels, water treatment operations were unable to meet water licence discharge criteria and the mine itself was under risk of closure due to limited water storage capacity. Under these internal pressures, the mine initiated its own research initiatives designed to restore water treatment operations. The new process developed from the mine's research, utilized the mine's existing water treatment plant hardware but introduced a pretreatment step involving a discrete sludge recycle and removal system. In February 1989, water treatment operations resumed under the new process.

Jan 1, 1992

By E. Haug, Quamrul Ahsan, R. Norcross

Cyanide leaching is the most common process employed in the majority of the gold extraction plants. These gold extraction plants naturally generate tailings and/or effluents that contain highly toxic cyanides, In geographic locations with excess precipitation and therefore net positive water balance, a portion of these tailings must be discharged. Before these highly toxic cyanide-containing effluents can be discharged to the waterways, cyanide and any other toxic substance must be destroyed. Geographic locations with high evaporation and low precipitation, as in the western USA, result in net negative water balance and therefore these plants can operate with a zero discharge option. However, with the current stringent environ­mental regulations and concerns for bird and wildlife mortality, even these operations may be required to partially treat their tailings to preclude potential harm to wildlife. Furthermore, heap leach opera­tions are now generally required to detoxify the heaps before abandonment. It is, there­fore, apparent that all gold extraction plants may be required to install some form of effluent treatment in order to achieve the above objectives,.

Jan 1, 1990

By Albert R. Rule

Beneficiation studies were made by the Bureau of Mines to develop a process for concentrating phosphate minerals from the altered rock of the Phosphoria Formation. This report describes research on intermediate - and marginal-grade ores from southeast Idaho, The process developed consists of attrition scrubbing and sizing to produce a coarse concentrate; desliming at about 800 mesh (18.5 microns); flotation of the fine sands; roasting of the combined concentrates for removal of organic carbon and combined water; and leaching with SO2 for removal of magnesium and nonapatitic calcite. Results of continuous tests on three different ore types showed that approximately 80 percent of the available phosphate can be recovered at a grade suitable for phosphoric acid production. While leaching with SO2 is not necessary for all ore types, it is an important step in purifying concentrates containing excessive magnesium.

Jan 1, 1966

By J. A. Eisele, G. E. McClelland, M. D. Wroblewski

The Bureau of Mines is conducting research at its Reno Research Center to develop a staged agglomeration-heap leaching system and to electrowin the dissolved precious metals from the pregnant leaching solution. For direct electro- winning to be successful, the pregnant solutions generated during the Initial stages of leaching must be higher grade than obtained by conventional heap leaching. The precious metal concentration of the pregnant solution can be Increased by agglomeration pretreatment with cyanide solution which starts the leaching process during the curing period, by leaching with small volumes of solution and by cycling the leaching solution through more than one heap in a staged manner. The resulting pregnant solution is passed directly through an electrowinning circuit. The barren solution from electrowinning is recycled to the leaching circuit. Bench-scale research on the development of the staged leaching system and on the development of an efficient electrowinning cell are described. The Bureau of Mines developed agglomeration- heap leaching technology. This technology was readily adopted by the mining Industry for heap leaching crushed ores and mine wastes. Current research involves the application of this technology to finely ground feed materials such as precious metal-bearing milled tailings. Tailings agglomeration-heap leaching has also been used commercially.

Jan 1, 1984

By Yinan Zhang, Y. Luo

Most of the reported coal spontaneous combustion events occur in surface and underground mines where low rank coals (i.e., subbituminous and lower for this particular studies) are extracted indicating their high propensities for spontaneous combustion. Low rank coals have high moisture content (15 to 45%) and are capable of absorbing more moisture in dried condition. However, it is hard to induce the initial stage of self-heating process for the low rank coal using the current laboratory R70 testing method — a method widely used in the coal industry. Like a sponge, dry low rank coals can absorb water vapor in the air while the heat contained in the moist air is transferred to coal and served as the required activation energy to initiate the coal self-heating process. In order to prove this theorem and quantify the effects, the R70 adiabatic oxidation testing method has been improved to introduce a controlled moist flow into the coal reaction vessel. Tests using the new method and its setup on low rank coals showed that the initial self-heating process of coal sample can be greatly accelerated by the added water vapor — impossible with the regular R70 method. Once the self-heating is sustained, the removal of air moisture can further accelerate the process.

Sep 17, 2021

By Keith S. Liddell

Gold in many ores occurs in sulphides, which, if the gold is finely disseminated, renders the ore refractory and therefore not amenable to the simple process of milling and cyanidation. Traditional methods of treatment of these refractory ores is to produce a sulphidic flotation concentrate which is roasted to form a porous calcine from which the gold is recovered by cyanidation. The roasting process imposes a constraint of a minimum sulphur grade of the concentrate on the flotation plant, which may lead to a lower gold recovery being achieved in the flotation section. Thermal decomposition of the concentrate by roasting means that the sulphur contained therein has to be treated and disposed of in an environmentally acceptable manner; and, if arsenopyrite is present in the concentrate the environ- mental aspects will be worsened. It has long been recognized that finer milling of gold-bearing materials improves the liberation of gold, especially when the gold particles are very fine. After extensive laboratory and pilot plant investigations (Liddell, Patents), a suitable mill has been developed for the mining industry by Metprotech, which is capable of producing very fine grinds (down to 90 percent passing one m if necessary). In the course of the investigations it has been found that a large number of gold-bearing materials are amenable to fine milling. A specific advantage that fine milling of sulphidic materials has over oxidative processes such as roasting and bacterial leaching is that the sulphides are not decomposed and there is therefore not a sulphur disposal problem. Furthermore, the milled sulphides can become a future sulphur feed source, and can be reclaimed if necessary. A further feature of the Metprotech process is that it is possible to add cyanide to the mill feed

Jan 1, 1988

By Broderick E. Davis

Each year, about 45 Mt (50 million st) of flotation tailings are discarded in Florida phosphate operations. These tailings only contain about 4% of the phosphate in the ore. However, more than half of the phosphate in the tailings is concentrated in the +600 µm (+28 mesh) size fraction at grades of up to 20% P205. Many phosphate producers have attempted to solve this problem by floating the +425 µm (+35 mesh) flotation feed separately. However, phosphate recoveries in these circuits are typically only 60%. For seven sampled phosphate operations, the phosphate content of the +600 µm (+28 mesh) fatty acid tailings ranged from 15% to 25% P205. In every case, the +600 µm (+28 mesh) fatty acid tailings was higher in grade than the overall flotation feed. Attempts to efficiently recover this coarse phosphate have apparently been unsuccessful at these seven phosphate operations. Recovery of this coarse phosphate would provide an additional 900 kt to 2.5 Mt (I to 2.7 million st) of phosphate annually and add an additional year to the reserves of these important deposits. A typical central Florida phosphate matrix is composed of three different mixtures of minerals. The +1.18 mm (+ 16 mesh) portion is chiefly phosphate pebbles and is beneficiated by sizing. The -106 µm (-150 mesh) portion contains virtually all of the clay minerals and is discarded in the hydrocyclone overflow. The -l mm +106 µm (-16 +150 mesh) material is a mixture of quartz and phosphate minerals.

Jan 1, 1993

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By Steven I. Olson

Since the introduction of froth flotation, the Florida Phosphate Industry has faced the challenge of coarse particle -850 +425µm (-20 +35 Tyler mesh) beneficiation. Several techniques have been used to upgrade this difficult size range. This paper discusses one approach that has met with success; namely, improved fractional recoveries through enhanced areation and improved material transport characteristics via larger than standard flotation cell mechanisms.

Jan 1, 1981

? The economic health and national security of the U.S. depends on the continued availability of, and access to, reliable and affordable energy and mineral resources. However, America is hindered by a costly, inefficient and often redundant regulatory structure that thwarts domestic investment, expansion and job creation. The annual cost of federal regulations in the U.S. increased to more than $1.75 trillion in 2008; averaging $8000 per employee.(The Impact of Regulatory Costs on Small Finns, SBA, 2010) ? The complexity, uncertainty and delays within the current permitting system places the U.S. at a competitive disadvantage with many other countries that have both abundant mineral resources and a more welcoming business and regulatory climate. As a result, American and international mining companies often move overseas or across borders to invest capital, create local employment, and produce the critical minerals America must then import at higher cost, while sacrificing employment and economic stimulus. ? According to Behre Dolbear, the U.S. is ranked lowest globally due to the lengthy permitting period required before mine development can commence. (Where not to Invest, 2010).

Jan 1, 2011

By III Boxley

Most of us realize that our nation's roadways are under ever-increasing stresses, from higher traffic counts to increased tire pressures and their resulting loads. At a time when the interstate system as originally envisioned is completed, and the National Highway System is being drawn to replace it, it is appropriate that we examine design and construction methods for the next century. The stone industry shares a common desire to produce high quality, cost-effective roadways that perform over time. The superior sub-grade and road base structure provides for the superior roadway. Since I am neither an engineer nor a contractor, I will not attempt to suggest design or construction methods. What I can do is share my company's experience in supplying road base materials by using a historical perspective in Virginia and some trends in the market that we have observed. Road building and related non-building construction are still far and away our largest markets as an industry. If we can help to improve the end product of our biggest customers, we add value to our own product. Indeed, in a time of budget constraints and competing demands for government dollars, we must show value over the life of a pavement structure to ensure their long-term funding.

Jan 1, 1996

By Bill Kendall

"In coal mines, handheld air, electric and hydraulic powered drills are used along belt conveyors, in single entry development, in entries where there are obstructions, and in longwall recovering bolting. In hard rock mines, pneumatically powered jackleg drills are typically used in narrow vein mining. Drilling and bolting in narrow confines has traditionally been performed with pneumatically or hydraulically powered hand-held drills or newer electrically powered hand- held hammer drills due to their low cost, simplicity of operation, and extreme flexibility due to their small size. Mechanized equipment has typically been too large, too expensive, inefficient due to the confined space, and too restrictive due to lack of flexibility for use in narrow confines.Although the handheld equipment is effective, it requires operator exposure to certain inherent hazardous conditions in use. These include falling rock from the roof, rib and face; tripping hazards; bending twisting lifting hazards; high noise levels and chemical fumes from the pneumatic exhaust. The operation of the hand held equipment can adversely affect the long-term health of the operator - continual jackleg operation frequently results in longterm damage to hearing, shoulders, arms and wrist joints and back injuries. This results in a reduction in life style for the operator and higher personnel turnover rates for the mining company.Hand-held drills also typically have limited thrust and torque capability that limits their ability to push long resin bolts, inadequate torque to properly install resin bolts or to properly torque mechanical or tensioned rebar bolts. Hand-held drills do not offer any type of protection for the operator from roof or rib falls. They do not offer any means for handling roof or rib mesh. Since the operator stands on the ground the maximum safe drilling height without use of a ladder or "riding the drill" is limited to 2.44 m (8 ft)."

Jan 1, 2014