Search Documents

By Hiroyuki Abé

This paper is a review of research and development on geothermal energy extraction in Japan especially on hydraulic fracturing. First recent geothermal developments in Japan are outlined in Part I. An increase in the production rate of geothermal wells may be highly dependent on the geothermal well stimulation technology based on hydraulic fracturing. The hydraulic fracturing technique must be developed also for geothermal energy to be extracted from hot, dry rock masses. In Part II, the research on hydraulic fracturing and field application are reviewed.

Jan 1, 1982

By Anders Sellgren, K. Hansson, A. Jedborn

In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore. from a system's point of view, slurry transportation would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alternative examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasibiliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. 1. The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then temporarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe- line, and personnel are needed. In a first phase (Fig. 2). a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1990

Introduction Aggregate mining impacts on water resources are a source of concern to local governments. To evaluate those impacts, the Minnesota Department of Natural Resources conducted a four-year study at three gravel pits (two alluvial and one beach-ridge) and five quarries (flat-lying Paleozoic limestone). This research provides the first comprehensive look at aggregate mining impacts on ground-water systems in Minnesota. The results will be used by government officials making permitting decisions about aggregate operations and by responsible owners of aggregate mines as they plan their operations to avoid conflicts with neighbors and with resources dependent on ground water and surface water. Natural aggregate (crushed stone, sand, and gravel) is a vital part of our economic infrastructure in Minnesota. Aggregate is used for road and bridge construction and in a variety of building materials. In 2003, the value of construction sand and gravel and crushed stone in Minnesota was approximately $245,000,000. As Minnesota’s economy continues to expand, the demand for aggregate will continue to grow. Sand and gravel pits are located in every county in Minnesota. In 1990, the Minnesota Department of Natural Resources, Division of Minerals (DNR Minerals), estimated the number of active and inactive operations at 1500 with the view that this number was likely too low. Quarries for mining limestone, dolomite, sandstone, and hard rock (granite and quartzite) are found in 34 counties. A 1990 DNR Minerals inventory found 165 active operations, 88 percent of which were limestone quarries (Nelson and others, 1990). That same inventory counted 1,367 inactive operations, 70 percent of which were limestone quarries. Aggregate mining is an extractive use of resources: mining alters the landscape and its natural hydrologic system. When a new pit or quarry is proposed or when an existing operation needs to expand, local governments and citizens typically have many questions about the impacts mining might have. Local governments, which are responsible for reviewing these operations, rarely have the budgets to hire experts to evaluate potential impacts of quarry and gravel pit proposals. The Minnesota Legislature’s Aggregate Resources Task Force identified that local government units (LGUs) often lack the expertise to assess ground-water models (Southwick and others, 2000).

Jan 1, 2007

Draglines are one of the largest land-based equipment moving across the earth. They typically ranging in size from2.5 to 6.5 kt (2,750 to 7,100 st). Their size, though, makes them difficult to maintain. Recently, G&S Engineering Services used an Enerpac synchronous hydraulic lifting system to lift a 3.2-t(3,500-st) dragline at the Curragh Mine in Queensland, Australia’s Bowen Basin.

Jan 1, 2004

Machine breakdowns and maintenance delays are large contributors to lost production and increased operating costs in the mining industry. The U.S. Bureau of Mines is investigating the applications of expert system technology to diagnostic and predictive maintenance tor mining equipment. This will help increase mining productivity and decrease operating costs, by reducing the frequency of equipment failures and repair times. The Bureau has begun this effort by applying expert system techniques to the diagnosis of hydraulic system problems on a continuous mining machine. This paper discusses the development of the hydraulic diagnostic expert system.

Jan 1, 1990

By James L. Evers

The development of hydraulic mining in the United States has had an uneven record of progress. The shifting of coal extraction from one government agency to another has not provided an environment for a focused national research program. This paper presents an update on hydraulic mining research in the United States. A comparison is made between the development of the technology in this country and the state of the art in other parts of the world.

Jan 1, 1983

By J. M. Baker

It seems appropriate here to open with a quotation from the great pre-Confucian philosopher Lao-tze: "The softest thing in the world dashes against and overcomes the hardest. There is nothing in the world softer or weaker than water, and yet for attacking things that are firm and strong there is nothing that can take precedence of it." I am happy to report that our system of mining has worked out, with minor modifications, as well or better than was predicted. This, in a period of rising labor and material costs, has been most gratifying. Gilsonite is a solid hydrocarbon which occurs in vertical fissures cutting the sandstone and shale beds of the Uintah formation in south¬eastern Utah. It is found in other parts of the world under similar occurrence but nowhere else is it now being mined commercially. The Gilsonite veins on entering the shale members of the Green¬river formation break into small veinlets separated by shale, These veinlets are not now economical to mine.

Jan 1, 1959

By Sam S. Arentz

Storm King Mines began with the concept that the resource potential of thick and steeply pitching seams of the Grand Hogback region of Colorado could be mined profitably. Two large tracts of private land (fee coal) were acquired; approximately 23.8 km2 near Glenwood and 16.2 km2 near Meeker. Figure 1. Although both properties have substantial coal reserves, one has several distinct advantages in developing a competitive mining operation. Table 1 illustrates these advantages. Among the most important considerations from an economical point of view are proximity to railroad, highway, labor force, quality of coal, seam thickness, and source of water. As can be seen, Storm King Mines' property is adjacent to the main line of the D & RGW Railroad, 1-70, and the Colorado River. The cities of New Castle, Glenwood Springs, Silt, Rifle, Carbondale, and Parachute are within short commuting distances and have available skilled labor.

Jan 1, 1983

By C. Green, J. Uhrie, C. Filippone, A. Guzman

A central aspect of heap leach management and recovery optimization is solution control. Insofar as each heap is unique in physical and metallurgical properties, it is essential to understand the hydraulic parameters that control the migration of solution on a case-by-case basis. Water Management Consultants, as part of an ongoing research effort for Phelps Dodge Process Technology Center, have adapted techniques of parameter estimation for application to data typically resulting from metallurgical column testing. The parameterization is completed within the context of a variably saturated flow model that allows interpretation of available hydraulic information collected during hydrometallurgical column tests. A novel interpretation approach is introduced to extract the necessary hydrodynamic parameters from typical hydrometallurgical data sets. Results from the application of the approach to standard metallurgical test data will be presented together with a discussion of the application of information gained to the design and operation of a heap.

Jan 1, 2002

By W. B. Greer, J. J. K. Daemen

Introduction The performance of seals in boreholes, shafts and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall et al., 1982). This research involved the installation, extensive hydraulic testing, removal and post-test examination of a 10-cm-long x 10-cm-diam cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble Peak in the Santa Catalina Mountains, AZ. A test hole was diamond cored in the recrystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diam, and dips at 10.4°. The hole extends between two drifts and thus is accessible from both ends. Seal installation Surveys to assist in selecting the interval to seal consisted of core logging, video logging and constant-head injection tests using a straddle-packer unit. The location selected, 3 m from the lower end of the hole, had low hydraulic conductivity (3 x 10-10 to 3 x 10-9 cm/sec) and was free of significant fractures. The grout used, an expansive Class A cement, was provided by Dowell-Schlumberger, Tulsa, OK. A grout mass about 1.5 m in length was installed, with a dump bailer, above a temporary mechanical plug. Groundwater in the hole, if any, was minimal during placement. After 13 days of curing, the grout mass was partially drilled out from both ends, leaving a seal 10 cm long. Water distribution in rock mass The distribution of water and fluid pressure in the rock mass near the seal appears to be complex. The generally dry condition of the borehole and rock mass suggests that the rock mass near the seal was unsaturated prior to the injection tests of this research. The injection tests presumably created an expanding saturated zone around the seal. However, anomalously high fluid pressures, consistently recorded by one of two piezometers installed near the seal, suggest connection to a source of significant natural hydraulic head. Comparable head variations for closely spaced piezometers have been reported by others (Sowers, 1976). [ ] Seal testing The seal was tested for 3.5 years, using steady constant-head, tracer travel-time, dye-injection, head-buildup and transient constant-head tests. These tests are fully described in Greer and Daemen, 1991. In the head-buildup test, transient flow occurs through the seal (and rock mass) to a closed, water-filled interval of the borehole adjacent to the seal. The test consists of monitoring the rise in head in the closed interval until steady conditions are approached. The test may be analyzed in terms of a one dimensional analytical model to obtain the effective hydraulic conductivity (Ks) and specific storage (Sss) of the seal. Analysis in terms of an axisymmetric three-dimensional numerical model may yield properties of both the seal and rock mass.

Jan 1, 1993

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and concrete is described. Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fast-opening valve discharges the compressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh -pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard, massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited.

Jan 1, 1998

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and con¬crete is described Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fastopening valve discharges the com¬pressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh-pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited

Jan 1, 1997

By Kendrick C. Hardcastle

Although the basic techniques employed in hydraulic pumping in open pit mining have been practiced throughout the better part of this century, only relatively recently have studies of' sufficient depth and scope been conducted to improve these techniques. This paper will point out the basic techniques involved and some of the more recently discovered data concerning hydraulic pumping, Inherent in all hydraulic transportation systems apart from the consideration of transportation cast, is the outstanding advantage of slurrying the matrix at the mining pit so as to provide a lengthy and thorough soaking and washing of the material while in the pipe line and thereby reduce the necessity for washing, scrubbing and other treatment in the beneficiation plant. This is quite important in view of the constant increase in demand for a cleaner product.

Jan 1, 1964

By S. M. Cohen

Roll crushers had been used in the past ahead of existing milling systems in order to obtain additional production from such mills in both the mining and the cement industries. Historically, a roll crusher as a preliminator to a ball mill has been used for a number of industrial mineral applications. Flowsheets, from Taggars(1) show systems for fluorspar, graphite, lead and zinc to name a few, which are shown in Figures 1 to 4. These units applied, (in some cases still in service), prior to 1950 and as early as the 1920's, were of two general types, rigid rolls and spring rolls. The rigid rolls were phased out in favor of the spring rolls. The spring force related to the linear inch width of the rolls, ranged from 500 to 50,000 lbs/linear inch(1) on units up to 90" diameter. With choke feeding, the rolls were spread against the spring force during crushing keeping the system under high pressure to obtain high effectiveness.

Jan 1, 1986

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

This study developed machine learning (ML) models for predicting rock formation reactive forces experienced by a hydraulic shovel bucket during excavation. To do this, rock formation in the form of muckpile was modeled as granular ball elements in three-dimensional particle flow code (PFC) using linear bonding logic. A typical field-size hydraulic shovel bucket modelled in AutoCAD was used to excavate the rock formation and the three-dimensional shovel bucket resistive forces required to cut through the rock formation were measured and recorded. The experiments involved different muckpile height, bulk densities, repose angles, and average fragment size. Six ML algorithms, artificial neural network (ANN), K-nearest neighbor (KNN), linear, random forest (RF), regression tree (RT), and support vector machine (SVM), were evaluated on their ability to predict the shovel bucket resistive forces. The input variables used for the prediction of the resistive forces were the muckpile bulk density, angle of repose, height, and fragment size. The results showed that the ML techniques are useful and reliable methods of predicting rock formation resistive forces based on the rock formation properties. This research is a preliminary step towards developing reliable models for accurate prediction of excavation forces/torques which could potentially enhance hydraulic shovel process automation.

Sep 27, 2021

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

The efficient and effective utilization of hydraulic excavators relies on, among other factors, a better understanding of the formation resistance during the excavation process. Studies on hydraulic shovel excavators have focused on optimizing the digging process by considering the reaction of the boom, stick and bucket, and analyzing the resulting moments at the shovel’s front-end joints. These studies failed to understand resistive forces from a statistical viewpoint. The purpose of this paper is to develop machine-learning models capable of predicting the formation of resistive forces during shovel excavation. The shovel’s excavation was simulated in the PFC 5.0 environment using a typical field-size hydraulic shovel bucket to generate the shovel contact forces required to overcome formation resistance

By Edward F. Nagle

Instrumentation engineers have recently devised practical methods of metering the net solids flowing in a hydraulic mixture. The solids flow rate is determined by measuring the specific gravity and the flow rate of the mixture. T e specific gravity is measured by a variation of the bubbler system. The flow measurement is made by a somewhat unorthodox orifice requiring field calibrations. The linear mixture flow signal is then multiplied by the specific gravity signal, which is directly proportional to the percentage of solids in the mixture, to produce a linear solids Slow rate signal. The computations in this system are performed by Sorteberg pneumatic relays. Having obtained this measurement, integration and automatic control of hydraulic solids flow are available. This system is useful in mining, drilling and dredging industries. It provides maintenance of the net solids flow rate and reduces power consumption. Automatic control will provide rapid stabilization of net solids flow rate and release operators from making menual adjustments. The advantages of this application are economy of operation and increased pump efficiency, This paper describes a hydraulic solids flowmeter system installed aboard a dredge. Its purpose is twofolds:- 1. 20 provide a summation of the net solids flowing 2. To make available a practical guide for the drag tender operator. (Dwg. GSD-2219)

Jan 1, 1958

By Mehmet Guney

During the last decade various modifications of room and pillar and sub-level methods have been tried in an effort to eliminate gob-fires, dangers from roof falls, surface subsidence and to increase efficiency of extraction in the Armutcuk Mine, Turkey. It was eventually decided that the most likely system to give maximum benefits in view of existing geological conditions and coal seam characteristics was a system of cut-and-fill stoping employing hydraulic stowing. This paper has attempted to examine the trends of working techniques of hydraulic stowing. In addition, the results achieved and technical problems involved are discussed.

Jan 1, 1968

By Harold F. Yde

Hydraulic tailings fill in the Butte deep level mines was based upon studies made in 1958 by the Anaconda Company Mining Research Department, which published Bulletin No. 35, entitled "Hydraulic Stope Filling". Since then, many things have changed. At the time of the Research Departments study, dry mine tailings were hauled by rail cars from the Anaconda tailings ponds, twenty-five miles distant, to the underground mines' tailings fill plants at the Leonard Anselmo, and Mt. Con Mines. Now, with the installation of the new Weed Concentrator in Butte, tailings is delivered by pipeline to a cyclone at the Kelley Shaft, and stope filling has become more highly automated and streamlined. Presently, mill tailings at approximately thirty percent solids by weight, is pumped from the concentrator, eight thousand feet horizontally and upward, to the Kelley Fill Plant, where they are dewatered and deslimed by three Krebs Model D20B Cyclones, which discharge the material into the cased and grouted mine delivery bore holes at desired densities up to seventy percent solids. The vertical boreholes and four-inch rubber lined Victaulic pipe carry the material downward to horizontal distribution lines, which in turn tap into the stops-filling, three inch, unlined steel Victaulic pipelines. The slurry may travel several thousand feet before it finally discharges into the stope, where it lends support to the mined-out area.

Jan 1, 1969