Search Documents

By Mark Colwell

As per most other earth science engineering problems, the underground coal geotechnical environment and the way in which roof and rib support interacts with the rock mass are complex issues. While the problem should not be oversimplified (i.e., the dominant failure mechanisms or critical data input parameters should not be ignored), without question judicious simplification is at the heart of all good engineering design. Engineers play a vital role in supplying the world with solutions and products; however it is crucial that engineers make practical and readily useable contributions. One way to ensure this is to employ simplification in the engineering process.

By Wayne Green

The Regional Municipality of York, located north of the City of Toronto in Ontario, Canada, has experienced unprecedented growth during the past decade, with new home construction averaging 15,000 units per year. This rate of growth is planned to continue well into the future with a projected growth of more than 500,000 new residents by 2031, combined with a tar-get of more than 300,000 new jobs to provide a sustainable economic base for the region. It should be noted that York region has been designated as one of the key growth centers by the province of Ontario, aimed in part to meet the housing and employment needs of Canada?s growing population. York Region is a mix of urban and rural areas and is one of the most desirable areas to live in Southern Ontario. York region offers an attractive lifestyle, with its nine municipalities and the amenities created by the many rivers, streams and protected greenbelt areas that encompass more than 69 per cent of the region?s area.

Jan 1, 2010

By R. W. Smith, D. L. Taylor, K. A. Altman

The importance of metallurgical information in reaching appropriate decisions during the development of mining projects is demonstrated. A financial analysis is calculated using discrete system simulation. The results are compared to the results of a traditional sensitivity analysis. The traditional analysis is shown to have the potential to overestimate the value of mining projects. The type of statistical distribution used in a random number generator affects the results significantly. The statistical method of analysis provides insight into the amount of metallurgical testing needed and provides verification of how representative the samples are.

Jan 1, 2002

By R. W. Smith, D. L. Taylor, K. A. Altman

The importance of metallurgical information in reaching appropriate decisions during the development of mining projects is demonstrated. A financial analysis is calculated using a simulation that includes random number generators. The results are compared to the results of a traditional sensitivity analysis. The traditional analysis is shown to have the potential to overestimate the value of mining projects. The type of statistical distribution selected for the random number generator affects the results significantly. The statistical method of analysis provides insight into the amount of metallurgical testing to be completed and verification of how representative the samples are.

Jan 1, 2000

By A. Fuerst

The recent seismic events have shown that earthquakes have an immense destructive power. Chile was hit in February 2010 with a seismic intensity of 8.8 on the Richter scale, and had loss of about 700 killed persons, while Haiti was hit in January 2010 with 7.0 killing about 220?000 people. The event in Haiti showed that the seismic events can lead to a disaster if no preventive measures are taken. On the other side, the seismic event in Chile has hit a well-prepared country with moderate consequences. The earthquake with 6.6 Richter in Japan in March 2011, have further shown how severe the consequences can be if critical equipment is involved. Fortunately, the equipment in a mine has not the potential hazard as a nuclear power plant. Anyway, we are diligent and it is obvious that the seismic risk may lead to a real disaster even if the probability is small. The GMD is an important component in the grinding circuit of a mine. This paper maps out earthquake-prone areas including expected earthquake magnitude calculated according to relevant standards, focusing mainly on the building code IBC 2009. An overview is provided on how this standard is applied to mining equipment to minimize damage and aid large mills in operation to successfully withstand seismic effects. The differences in stresses and forces on the GMD and foundation are shown based on a turning and stopped mill simulation during an earthquake. The results demonstrate the need to maintain active and operating earthquake detection systems. Aside from detecting an earthquake?s magnitude, the sensor information can also be used to reduce the harmful effects that an earthquake has on mining equipment. As follows the earthquake requirements are defined. The last part of this paper explains how to fullfill these requirements.

Jan 1, 2012

By Edgar F. Cruft

It is sometimes said that "mines are made, and not found". I rather doubt that the exploration geologist would be overly sympathetic to that statement, and, of course, like most one-liners it is only partly true. As an explorationist who has been involved in building his own company over the last ten years, and by necessity has become a financier, I can appreciate what real grains of truth are in that statement, however. Because technical people are seldom taught financing in their basic training, and because they are usually not involved in it until at quite a senior level in their careers, the whole field often acquires a certain mystique. The engineering professions have too often believed financing is the province of the accountant or financial executive and just as we in the technical world are often too quick to bristle if the latter try to tread on our domain, the opposite can just as easily be true. Unfortunately, this is another example of a compartmentalized individual, and that is one thing the successful financier cannot be.

Jan 1, 1979

By Delbert L. Keenon

The principal concepts of computer control and automation have been successfully applied in industries world-wide, The enthusiasm generated by the proponents of computer control, and the apparent mystery enveloping the techniques of computer control, have caused attention to be focused on this infant industry from all quarters. Consequently, the motivation to "computerize" may be the hope that computers will solve all economic problems. The truth remains that not only have there been monumental successes, but there have been some colossal failures. This paper will attempt to outline a generalized guide to computer control and present methods for avoiding some of the major pitfalls. Since the investment required for computer control systems has been drastically reduced in the past year, small operations will likely find that computerized process control is attractive in areas where it has never been considered before, The discussion presented here is intentionally non-technical and directed towards those who may soon find they have a possible application for a control computer. The primary purpose of computer control is to reduce expenditure and increase profits by improving the quality of product, increasing the efficiency of operation, reducing the materials and man hours required or a combination of these. Success or failure to reach the desired goal depends, to a large degree, on a well-planned approach. This includes recognizing a possible computer application, properly defining the job which is to be accomplished, evaluating computer systems, selecting a capable manufacturer, and following through with sound systems engineering and programming.

Jan 1, 1965

By Leonard Harris

Since the end of the cold war following the collapse of communism, enormous amount of funds are pouring into the developing countries including investments by mining companies for the development of gold and silver mines. A great deal of these funds are destined for expenditure in areas riddled with bandits, terrorists and active and latent criminals bent on stealing the mine operators hard earned production on its way from the mines to markets. Brambles Security Services employs experts in the field of safely transporting gold and silver products under various alternatives and aimed at relieving the mine owners of this responsibility. This paper examines the various service options available.

Jan 1, 1997

By J. L. Marchese

Belt conveyors face their applications life with a promise of constant abuse: heavy and rough products cascade onto the belting without let-up; caustic and abrasive materials such as salt and ore eat away at the cover; high temperatures, even open flame at times, sear and soften belting materials; and unyielding tension stretches and strains every belting component. The only defense against the applications onslaught is to follow the basic rules of proper handling, installation, and maintenance. Under the direction of qualified personnel (one responsible person, if possible), you can insure that conveyor belting begins operation in top condition.

Jan 6, 1980

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert system shells designed for real-time processing plants that also included the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. Significant performance increases have been achieved using these systems, but in general, they suffer from the static nature of their rules and to a degree the process models also. Typical improvements quoted in the literature suggest throughput rate increases of 4 to 8 percent and recovery increases of 1 to 4 percentage points. In over 30 years of designing and installing expert systems we have never seen performance numbers less that these but have often seen numbers in excess of the high values. However, once the system has been installed and tuned up the performance usually does not improve much thereafter. Granted, the initial increases in throughput rate and recovery are significant but a question always lingers, that is, can the expert strategies be modified further to squeeze a little more improvement out of the system. The answer to this question is a resounding yes, however a complete understanding of what we do well as designers and operators of expert control systems is required as well as how we can improve upon our best practices is required to move us from the performance plateau we have been on for a number of years to a new higher level of performance.

Jan 1, 2009

By Steven J. Luzik

Introduction From 1973 through 1986, a total of 12 fires involving oil-flooded rotary screw compressors (OFRSC) were reported to the Mine Safety and Health Administration (MSHA). Most of these incidents were attributed to faulty or by-passed safeguards, or improper maintenance. The cause of a fire in an OFRSC is unique when compared to other types of compressors. A compressor inspection checklist is provided here that can be referenced when conducting regularly scheduled maintenance operations. This checklist and a well-planned program of periodic training and maintenance should help minimize the probability of fires and explosions in OFRSC's. Operation A rotary screw compressor operates on the principle of positive displacement of air. Compressed air in this type of compressor is produced by the meshing of two helical rotors, or screws, as they rotate within a steel housing called a stator. The male rotor normally has four lobes and is driven either directly or indirectly - through a gear assembly - by a motor. It intermeshes with a female rotor having six cavities. Figure 1 explains the compression mechanism: (1) Atmospheric air is drawn into the stator by the suction action of the two rapidly rotating rotors. (2) As the rotors rotate past the intake port, air is trapped in the stator and in the cavities between the rotors. (3) Further movement of the rotors causes an increased reduction in volume, compressing the entrapped air. (4) Compressed air is expelled at the discharge port in the bottom of the stator at a pressure and quantity determined by the particular compressor rotor design parameters, such as length, diameter, and speed. Radial bearings on the male and female rotors compensate for radial loading on the shaft and position the rotors within the stator. Thrust bearings on the discharge end of the compressor prevent rotor misalignment due to thrust developed during the compression cycle. This design prevents the male and female rotors from making contact with each other or the stator. A clearance of 0.07 to 0.1 mm (0.003 to 0.005 in.) exists between the two rotors and the stator. For this reason, there is virtually no wear on the rotors or stator, and the unit is relatively maintenance-free. Oil is injected into the compressor and serves to cool, seal, and lubricate. When air is compressed from atmospheric pressure to some higher discharge pressure, a specific amount of heat is produced. This heat is sometimes referred to as the adiabatic heat of compression. It is partially removed by injecting oil into the compression chamber. Premachined strips - a raised surface on the male rotor and a

Jan 9, 1988

By Robert W. Greene

Next month, American Commercial Barge Line Company will begin moving coal from mines on the old Camp Breckinridge property in Western Kentucky to TVA's new 2600 MW steam plant at Cumberland City, Tennessee. By April of 1973, this movement will reach a level of 7,000,000 tons per year. TVA bought the coal rights to this property from the General Services Administration in 1965 for approximately $7 million. The reserve contains about 120 million tons of recoverable No.9 coal, and about the same recover-able amount of No. 11 coal. TVA then contracted through competitive bidding with Peabody Coal Company to mine the No.9 seam through two slope shafts. The mines are about 300 feet deep and are separated by the one major fault on this property. The mine portals are approximately 3-1/2 miles apart, with the northern portal being over nine miles distant from the Ohio River (see Figure No.1). In 1969 TV A took bids on alternate methods for transporting 120 million tons of coal to Cumberland City at seven million tons per year. These alter-natives included overland transportation to the Ohio River by rail or conveyor, water transportation from Union County, Kentucky to Cumberland City, and total transportation packages from Camp Breckinridge to Cumberland City. The latter could be a joint land/water package, or all land (rail). Ultimately American Commercial Barge Line was awarded an $88 million package transportation contract to convey the coal from Camp Breckinridge to Uniontown, Kentucky; to store it at Uniontown in a quantity sufficient to allow ratable delivery to the steam plant; and to barge from Uniontown to Cumberland City via the Ohio and Cumberland Rivers.

Jan 1, 1971

By V. L. Andrade, K. L. C. Goncalves, N. A. Santos

This paper describes results obtained in a test program performed with new equipment, called Mini Pilot Plant, manufactured by Canadian Process Technologies. This equipment was acquired by CVRD aiming at testing flotation circuits, in a continuous closed configuration, with samples obtained from drill cores. Success of this goal would allow CVRD to establish the metallurgical performance of mineral deposits with more confidence in comparison to Locked Cycle Tests (LCT). This paper discusses the importance of assessing the ore variability and compares results obtained in LCTs and Mini Pilot Plant. Results suggest that more reliable data is obtained in MPP test.

Jan 1, 2002

By R. W. M. Lai

The study of flotation kinetics was first reported by Garcia-Zuniga1 in 1935. Since then, literature on the subject has grown with the time. 2-19 Although there is an abundance of flotation kinet¬ics models available in the literature to describe flo¬tation systems, they are mostly of academic interest and are seldom applicable for use in the industrial environment. Several reasons contribute to the wide gap in the industrial -application of the academic models. These include: 1) the lack of generality in the model, e.g., the model is limited to certain size ranges; 14 2) the academic models involve complicated mathematics; 5,6,10,11 3) confusion about the order of the flo¬tation rate, e.g., several authors proposed a first order rate model, 1,15,16 whereas the others propagated a second order rate model: 2,17,18,194) the use of an unrealistic rigid value, such as the use of a maximum recovery of 100%, 5,8,19 which is unrealistic in industrial operations; and 5) the use of graphs that confuse the reader rather than interpret information. 2,3,10 This paper intends to introduce a simple and easy to understand empirical flotation kinetics model along with a way of presenting the model in an informative graphical form, which should stimulate the interest of other practical engineers to become concerned with practical application within the mineral industry.

Jan 1, 1982

By G. Tiravanti

A recurrent concern in mining operations is how to deal with the large volumes of fresh water used which in turn generates large volumes of effluents that have to be treated. Water treatment can focus in one of two main strategies: treat the effluent as it is produced, or use a simulation tool to optimize water use in the process and reduce volume of effluents, contaminants concentrations, operational costs, and so on. This article shows a successful tool developed in Matlab-Simulink® that allows modelling a mining process and simulating potential improvements to evaluate the results. This tool has been proven in Cu-Mo operations and recently it has been used in poly-metallic operations. This article reviews the 4 Key Steps required to achieve our goals: a) Elaboration and verification of the mining Operation?s Block Diagram, based on a field survey; b)Model construction and input flows and qualities in selected streams; c)Model Validation and Simulation of new alternatives like recirculation, changes in reagents and dosage, partial treatment, flows merges/separation, and others; d)Development of the Optimal Solution which consists on determining the CAPEX and OPEX.

Feb 27, 2013

By Leonard Harris

Good morning ladies and gentlemen. I would like to thank Hans von Michaelis for inviting me here today to talk to you on the subject of "How to Reduce Capital and Operating Costs at Heap Leaching Projects". The comments I have to offer are based on my experiences in gold heap leaching by Newmont Gold Company in Nevada, by Newcrest in Western Australia (formerly Newmont Australia), by Minera Yanacocha in Peru, by Penmont in Mexico, by Z­Mont in Uzbekistan, by the Hochschild Group in Peru and expe­riences in copper heap leaching by Magma Copper Company in Arizona and as a consultant on several other smaller projects worldwide. These comments are a mixture of technology, ideology, philos­ophy, strategy, logic and opinions and might be looked at by many of you as "one man's view". I like to look at them as "a view from the bridge". Let me add that it doesn't bother me that you may not agree with my comments and that I would be interested in your comments or criticisms at the end of this presentation. I don't intend to discuss the details of the mineralogical and metallurgical test work. I will assume, for this talk, that the test work has been conducted very carefully and that the ore in ques­tion has been determined to be heap or dump leachable. Let's begin with a couple of don'ts! ! First, "don't build the mill until you have a mine". This might sound to many of you as fundamental but believe me it continues to happen. The minable reserves should be well known and established as being economical to mine and leach. NPVs, ROis and IRRs are fine if you can be sure of the gold price you use in your calculations. The best method is to carefully estimate the capital cost and, most importantly, the operating cost per ounce of gold recovered which should include the repayment of the borrowed capital and the interest thereon. For example, if the operating cost under these conditions is $200 per ounce, you have a project. If it is $400 per ounce, walk away f om it. Incidentally, the same prin­ciple can be applied to projects involving other metals such as silver, copper, lead, zinc, etc. The second don't is - "don't be sheep". Don't climb on the bandwagon with respect to design and operation because every­one else does it a certain way. Keep an open mind, be versatile, look for change, look for every possible innovation for reducing capital and operating costs. Beware of those who will tell you "we tried that it won't work" or "it's too expensive" or "that's a crazy idea" , <' ''what do you know about mining - you are a metallurgist aren't you" or "what do you know about metallurgy - you are a miner aren't you" or "only geologists can handle this issue". Be careful about pigeon-holing people according to their basic degree and experience. In these days of low metal prices, we need to consider everybody's ideas, as crazy as some of them might seem.

Jan 1, 1998

By D. Kelley

Due to pricing volatility and lack of availability of metals, the use of non-metallic materials of construction in metal extraction and refining processes has increased significantly in recent years Even though costs and availability of metals has improved recently, these factors are not expected to continue into the future as metal supplies once again fall short of global demand. One of the most common non-metallic materials of construction used in metal extraction and refining processes today is Fiberglass- Reinforced Plastic (FRP). These processes often require materials of construction that can resist acids and high concentrations of acid chloride salts. As shown in Table 1, FRP based on epoxy vinyl ester resin has the same chemical resistance to acid and better resistance to acid chloride salts than alloy C-276 and is superior to 2205 stainless steel in both cases.

Jan 1, 2010

By L. R. Berry

The successful selection of a slurry pump depends on the accuracy and completeness of the information provided for the application. Inaccurate or incomplete information can result in incorrect pump selection and / or operational problems. Some information is more critical to the selection process than other information. A full description of the slurry (liquid -solid mixture) including the particle size distribution and maximum concentration, the flow, head and NPSH requirements are most important for successful slurry pump selection and operation. Common problems resulting from improper slurry pump selection will be discussed to illustrate the need for correct selection requirements.

Jan 1, 1996

By d&apos, I. J. Agati

The stockpiling and reclaiming of bulk materials can be a challenging task for engineers seeking the optimum solution for plant needs, reliability, and at lowest unit cost. The objective of this paper will be to expose advantages, disadvantages and limitations of many storage and reclaiming systems to the responsible engineer and management. The paper will emphasize the practical aspect of stockpiling and reclaiming methods. Many valuable and interesting papers are available dealing with the theoretical viewpoint and application of a particular manufacturer&apos;s machine. Several of these are mentioned in the bibliography. As many practical parameters as possible will be given. After twenty years in the field of designing and selling bulk materials handling systems, the needs of the user and the plant are recognized and reasonably understood. This paper cannot give solutions to all problems In this vast field but will stress practical applications and examples of various installations. The evolution of advancements in materials handling is based upon not only technological innovations, but learning from many experiences of others and utilizing them as stepping stones to improved installations.

Jan 1, 1969

By Steven A. Elmquist

INTRODUCTION R&D activities are needed, at a minimum, for a company&apos;s competitive survival followed in importance by the growth and diversification of the company. For most industrial companies, however, R&D is the business area that has been the most difficult relative to confident long-range financial commitments and effective control and relative to its value as a long-term investment. Investors look not only at the current profitability of the company but increasingly at the plans, actions, and quality of the personnel in position to improve the market position and profitability of an organization. "The strongest predictor of investment value is the degree of innovation of the &apos;company.&apos; I believe this is true of both strategic planning and R&D activities." R&D is the lifeblood of a company&apos;s future. If this basic premise-R&D for survival and growth-is believed to be true, why is it necessary to "Sell R&D in your organization? My personal experience, in a number of organizations, is that R&D budget is perceived as a business element area that could be delayed or reduced to improve the bottom line during difficult business conditions. I believe the following quote speaks volumes about this subject-"There is only one thing I know for certain about research, and that is it costs money-lots of it." -Unnamed, Hard- headed Financial Executive. A business must make money and be profitable in order to maintain and create jobs, pay taxes, cover working capital and costs of goods sold, and most importantly, create value for its shareholders. The foremost element of selling R&D, therefore, is to consistently demonstrate the R&D group&apos;s contribution to the bottom line.

Jan 1, 2004