Search Documents

By R. E. Hochscheid

Cyclones installed in three closed- circuit grinding systems were changed from conventional, vertical mounting to horizontal mounting with a favorable improvement in classification efficiency. In two of the installations, apex plugging problems were eliminated because horizontal mounting permit- ted the use of much larger apex orifices. Marked reduction in circulating load was accompanied by greatly reduced maintenance requirements for the cyclone and the cyclone feed pump in one of the installations.

Jan 1, 1988

By M. Santillan

Minerales Monclova S.A. de C.V. (MIMOSA) has applied different methane gas drainage technologies, according to the top industry requirements in order to keep the methane gas at the lowest possible concentration in our operations, both in the development sections and longwall sections. Our staff has used the horizontal rotary technique. In 2004 MIMOSA bought a re-built drill machine and signed a contract with Resource Enterprises Inc. (REI), which included a training program in Horizontal Directional Drilling using the reflex system. The training system was developed for a period of three months in Mine VII, with very good performance by the MIMOSA staff. After the training the equipment was moved to Esmeralda Mine, where we had already drilled holes at the development section, 2,500 ft. It was the longest distance that could be reached with our original equipment, obviously; the directional drilling program is another challenge for us and our staff, but we are very confident that our result will be better every time. We will be evaluating each borehole and expect to improve our results in each progressive borehole, until we can drill up to the capacity of the equipment. We are in the process of buying another drill with an electronic monitoring device (DD DMecca) in the following months.

Jan 1, 2009

By P. C. Thakur

Horizontal drilling in coal mines is a relatively new technology. The earliest recorded drilling in the United States was done in 1952 at the Humphrey Mine of Consolidation Coal Company for degasification of coal seams. Spindler and Poundstone experimented with vertical and horizontal holes for eight years. They concluded in 1960 that horizontal drilling in advance of underground mining appeared to offer the most promising prospect (for degasification) but effective and extensive application would be dependent upon the ability to drill long holes, possibly 300-to 600 m, with reasonably precise directional control and within practical cost limits.(1) Mining Research Division of Continental Oil Company, the parent company of Consolidation Coal Company, began a research program in the early 1970's to achieve the above objective. The technology needed to drill nearly 300 m in advance of working faces was developed by 1975 and experiments on advance degasification with such deep holes began in 1976. Preliminary Its of this research have already been published.(2) To date nearly 4500 m of horizontal holes have been drilled for advance degasification and earlier results were reconfirmed. In summary, these are: 1) The greatest impact of these boreholes was felt in the face area where methane concentrations were reduced to nearly 0.3 percent in course of two to three months from original values of nearly 0.95 percent.

Jan 1, 1979

By P. C. Thakur

Mine productivity, measured by the output of minerals per manshift, depends on a number of factors including physical conditions of the minable seam, type of mining equipment, management techniques, worker attitudes and governing jaws and regulations. The greatest scope of improving productivity lies, perhaps, in modifying physical conditions to an advantage and using highly productive equipment. In the case of coal mines, increased productivity can be achieved by (i) obtaining prior knowledge of the mineable property, e.g., the grade and thickness of, the coal seam, presence of sand channels, faults, etc., (ii) eliminating conditions that hamper production, e.g., high emissions of methane and water, and (iii) using more productive mining techniques. Conoco/Consol's (Conoco Inc. and Consolidation! bal Company, a fully-owned subsidiary) horizontal drilling system was developed with the hove objectives in mind. It can drill 75 to 1001 in diameter boreholes to depths of more than 600 1 and maintain the borehole in a preselected horizon. Such boreholes can be utilized for premining exploration of the coal seam, for removing methane and water and in devising mining techniques with high productivity. The purpose of this paper is to describe the horizontal drilling system briefly and to discuss its applications in the above-mentioned- areas.

Jan 1, 1980

By Nick Salisbury, Alan Howard, Scott Tunison

INTRODUCTION Geotechnical investigations for tunneling projects typically use vertical test borings and, to a lesser extent, angled borings. Horizontal drilling applications were often limited to specialty testing programs and to perform probe drilling from a tunnel boring machine (TBM) as part of production tunneling. The former often involved cumbersome setups with skid rigs and cribbing in a pilot tunnel or shaft. The latter usually was limited to generic probing for rock quality and ground water conditions with no sampling. Neither yielded continuous core at production rates suitable for design and construction planning. Conventional vertical investigations still make sense in many instances, particularly for tunnels planned beneath urban settings where truck access is convenient and where the tunnel horizon is not readily accessible via a portal or shaft. However, equipment is presently available to conduct horizontal geotechnicall investigations at reasonable production rates and cost. Advantages include continuously sampling the tunneling horizon and minimizing “access drilling” to get the zone of interest at the underground construction horizon. Horizontal boring lengths of up to approximately 800 m are considered feasible and those in the range of 150 to300 m are now routine. These capabilities make horizontal borings an attractive option to consider when looking at deep tunnels beneath ridges, especially where access is limited. Fewer drilling staging sites can also mean reduced environmental impacts when investigating tunnels proposed beneath sensitive lands such as public wilderness areas. Investment in early construction packages to develop portals for investigation access and, possibly in excavating test shafts for the same purpose should even be considered. Potential benefits in the form of achieving improved overall project costs using horizontal borings exist because of the significant additional data collected in the tunnel horizon. For this reason they should be considered during the routine cost-benefit analyses generally conducted for planning geotechnical investigations for tunneling. The authors also believe that collection of such data will reduce Geotechnical Baseline Report (GBR) conservatism and lead to lower potential for

Jan 1, 2005

By Jim Peregoy

INTRODUCTION Frontier-Kemper Constructors, Inc. is an Evansville, Indiana based heavy construction contractor engaged in projects for both the public and private sectors of the underground construction industry. Construction activities range from conventional shaft, slope, tunnel and chamber excavation through state-of-the-art mechanical excavation, ground freezing, standard support and structural concrete operations. Conventional excavation and concreting equipment, as well as raise boring machines, road headers, tunnel boring machines, and freeze plants are owned, operated, maintained and modified "in-house" to suit the needs of individual projects. The balance of this paper wilt present a general overview of the Frontier-Kemper planning and construction operations on the recently completed Phase II of the U.S. Army Corps of Engineers, John Day Dam, Juvenile Fish Bypass Project. General Project History The U.S. Army Corps of Engineers is responsible for designing, constructing and maintaining various navigation and impoundment structures on the nation's inland waterways. Maintenance involves both the work required to maintain the structure in fully-operable condition and the ongoing work required to maintain a positive impact on the environment. John Day Dam is located on the Columbia River approximately 95 km (60 miles) upstream of The Dalles, Oregon. It was constructed to: provide electric power to the Pacific Northwest; provide Locking for up-and-downstream bound commercial and private watercraft; act as a water impoundment structure to control flooding conditions; and to provide a source of irrigation water

Jan 1, 1987

By Steven I. Majtenyi

INTRODUCTION The heavy risk inherent in all underground construction projects contributes significantly to the high cost of transportation tunnels. First, the knowledge of this risk leads the engineer to design conservatively. Second, the cost overruns are still common with a high proportion of them originating from corrective measures needed when unforeseen problems develop during excavation. These unforeseen problems includes - encountering unexpected objects, materials and water conditions - experiencing an unforeseen behavior of the materials - damaging property beyond the expected range of influence of the tunnel construction. To minimize these expenses, more emphasis is being placed on well planned and interpreted site investigation programs in the final design and planning stages of the project. It is well known that the cost of a planned excavation is less than the cost of dealing with the same conditions when they are encountered unexpectedly. Therefore, the objective of site investigation is to provide a complete set of reliable data for designers and contractors that is continuous along the projected tunnel alignment. Two alternatives axe available to achieve this objective; - for shallow tunnels, it is often feasible to generate continuous data by drilling appropriately spaced, vertical bore holes and applying sensing techniques for interpolation (1, 8). - for deep tunnels, or certain urban tunnels under existing structures, closely spaced, vertical bore holes are not feasible except for narrow zones at the portals. In such cases direct horizontal penetration may be required that may be complemented by radial sensing to extend the range of information.

Jan 1, 1976

Successful longwall gate entry design requires control of vertical and horizontal stresses. Vertical, or overburden, stresses are most severe in the tailgate where they are concentrated by longwall panel extraction. Horizontal stresses can also be highly destructive but they are less well understood. This paper discusses measurements of in situ horizontal stress fields in the eastern United States, experience with horizontal stress in longwall mines and methods for predicting and controlling horizontal stresses. The information presented was collected through site investigations at 45 US longwalls and an international literature review.

Jan 1, 1992

By Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky, and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought, but rather 20° in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Jan 1, 1997

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global platetectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20o in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed

Jan 1, 1999

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania. West Virginia, Kentucky and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought but rather 200 in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Feb 24, 1997

By J. F. T. Agapito, L. J. Gilbride

High horizontal stresses were recognized to impact roof stability more than 60 years ago. Since then, numerous measurements associated high horizontal stresses with difficult ground conditions. This paper presents case histories illustrating the practical usage of roof stress determinations for helping assess stability, not only in the case of high horizontal stresses but also of low stresses. Examples are given of high stresses associated with faults, mine design changes, quantification of stress shadow effect, and anistrophy. The paper concludes with a comparative evaluation on the effect of various stress fields on ground support requirements.

Jan 1, 2002

By Thomas E. Bruner

Today many small diameter tunnels are being constructed in Metropolitan areas and towns as transmission holes for utilities such as water, electricity, natural gas and sewage, to name a few. These tunnels function as utilities beneath the streets, highways, railways, and other structures where open-cut techniques are impractical for any one of a number of reasons. Many such bores range in diameter from 15 to 72 inches and in lengths from 100 to 500 feet. Auger drills with auger type heads have long been used to bore these "road crossings" as they are usually termed; however, many such crossings must be bored in rock with rock-boring heads. Rock with a compressive strength of 15,000 p.s.i. and higher seems to present the greatest challenge for the contractor. These rocks include most igneous and metamorphic rocks and some sedimentary rocks. In general, this grasps most granites, basalts, gneisses, slates, schists, quartzites, limestones, and cherts. In the past ten years boring machines have been developed and used to excavate road crossings through hard rock. Many crossings have been successfully excavated using these machines, and the degree of success has increased substantially in the last few years. A variety of machines have been built and manufactured to bore most rock in a range of diameters up to 72 inches. The machines vary in capabilities, size ranges, and designs but all perform the same basic task and function of boring horizontally. Incidently, here the term horizontal implies horizontal or within five degrees of horizontal. In addition, there is a wide variety of designs, sizes, and types of drill stems, joints, and pipe to meet the various conditions and

Jan 1, 1974

By Joe Komadina

DOUG HALBE: Our next topic is one that I would think everyone might want to contribute to. I'm sure everyone here has had some experience in this area. If you haven't, I'd suspect you've never really run a mill. This is what we call "Horrible Spill Areas We Had When We Started Up the Plant and How We Fixed Them." Our next speaker has had a really great operating career. He had many years with Newmont in the Carlin area, and now he's executive vice president and chief operating officer of Independence Mining Company: Jim Komadina. I don't have to be nice to the speakers anymore, do I? [laughter] You may wonder why we picked Jim Komadina to give this talk. I was involved many years ago in the start-up of Newmont7s Gold Quarry plant. Jim held quite a responsible position there. I'm not going to say anymore, but I have in the back of my mind this picture of the pump floor and a rowboat and a guy rowing around on the pump floor. [laughter] Jim, was that you? [laughter] JIM KOMADINA: Probably. I wasn't responsible for the design. [laughter] Actually it's amazing. I've seen a lot of these plants and actually had the opportunity to walk around them, so when I say this, "Horrible spills I have seen and done," it's because I've been responsible for more than my fair share of them. But having seen a lot of spills, I will present a little bit of wisdom about how to prevent them.

Jan 1, 1998

By A. Noble

Linear circuit analysis (LCA) is a fundamental tool which has been used to evaluate mineral separation circuits during the preliminary design phase. Traditionally, the LCA methodology uses the analytic circuit solution to determine the relative slope of the circuit?s partition curve. This value is then used as an indicative performance measure suitable for the comparison and ranking of alternative circuit configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. In most mineral systems, this material represents a small portion of the initial feed (due to liberation) as well as a small portion of the revenue potential (due to the incremental value). Respecting these limitations, the authors have developed new separation performance indicators which may be derived from the analytical circuit solution and used in LCA problems. These indicators inherently reflect the separation potential of pure material, providing a better indication of lost revenue due to misplaced material. The complete methodology has been integrated with prior software to produce the Heuristic Optimizer for Resource Separation Economics (HORSE).

Feb 23, 2014

By R. M. Smailer

Detailed description of the development of the FIOR process1 and, subsequently, other technical papers relating to the operation and start up of the FIOR plant2,3 are available in the technical literature. The Fluidized Iron Ore Reduction (FIOR) process plant constructed in the Matanzas region of Venezuela represents the first commercial application of this technology. The FIOR process was developed by Exxon Company during the 1950's and 1960's; and the facility in Venezuela was designed and constructed by Davy McKee with the plant start up in 1976. While there is a minority government ownership in the company, FIOR de Venezuela operates as a private sector company with the majority of the ownership being private capital.

Jan 1, 1981

By Albert F. Duzy

Recently there have been some problems associated with hot coal in shipments from the USA to overseas markets. This paper will serve several functions. First, a brief review is presented, together with a selective bibliography. Second, a thorough discussion of coal oxidation is covered. Third, potential effects of storage are presented and, lastly, methods are suggested for the safe storage and bulk transfer of coal. The scope includes coal storage for power plants.

Jan 1, 1983

By Michael W. Roper

McDermitt Mine is located in northern Humboldt County, Nevada, approximately 5 miles south of the Orgeon-Nevada line (Figure I), within the Opalite Mining District. The operation is a joint venture between Placer Amex Inc., San Francisco, and Mineral Exploration Company Ltd., a limited partnership. The McDermitt orebody possesses a discontinuous, gently dipping blanket-like form within 150 feet of the surface over an area 2200 by 2500 feet. The ore zone averages 20 feet in thickness. The ore minerals consist of cinnabar (HgS) and corderoite (Hg3S2C12) deposited parallel to bedding within argillized, Miocene age, tuffaceous lacustrine sediments. Exploration indicates reserves of approximately 3,000,000 tons ore at a grade of 10 pounds mercury per ton (0.5%) An open pit mining operation utilizing scrapers and bulldozers supplies a concentrator with 700 tons of ore per day. The milling operation consists of autogenous grinding, flotation concentration, concentrate dewatering, and tailing disposal, with a design capacity of 100 tons per hour. The furnace section consists of a concentrate filter, vertical six hearth furnace, mercury condensing system, and exhaust gas scrubbing systems. It has a design capacity of 1000 pounds of dry concentrate per hour. The McDermitt orebody is situated about 2000 feet north of the Cordero Mine which, with adjacent properties, produced over 115,000 flasks (76 pounds per flask) mercury from 1941 to 1972' Two other major mercury producers in the district have been the Bretz and Opalite Mines, located in southern Malheur County, Oregon, within 5 miles of the Oregon-Nevada line. Bretz and Opalite have produced about 14,800 and 12,370 flasks mercury respectively, from 1926 to 1965.1/

Jan 1, 1976

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES, DAVOOD BAHRAMI

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron and carbon steel), three types of liquids (diesel fuel, hydraulic fluid and engine oil) and four air ventilation speeds (0, 0.5, 1.5 and 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperatures. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Oct 1, 2022

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES, DAVOOD BAHRAMI

The abstract discusses the issue of mine equipment fires caused by hot surface ignition of flammable liquids. The research investigates the ignition probability of liquid fuels (diesel, engine oil, hydraulic fluid) on different metal surfaces (stainless steel, cast iron, carbon steel) under various ventilation speeds. The results show that the type of metal and ventilation speed influence the ignition temperature, with diesel being the most easily ignited fuel and carbon steel requiring a higher ignition temperature. The study provides data for understanding equipment mine fires and developing mitigation strategies.

May 4, 2022