Search Documents

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001

By H. Reginald Hardy, Xiaoqing Sun

Rheological models are widely accepted as a means of describing the mechanical behavior of geologic materials. It has been found, however, that rheological models developed for a specific stress level on the basis of linear visco-elasticity generally are not satisfactory at other stress levels. It has been suggested that the parameters of such models should be functions of stress level (Hardy, 1965; Kim, 1971). In this paper, continuous functions of stress have been utilized to obtain the required variation of Burgers model parameters with stress level. The model developed using these functions provides a constitutive relation which reflects the real time-dependent behavior of rock materials. The new model is capable of predicting the creep behavior over a wide range of stress levels and also predicts mechanical behavior under different loading condition (e.g. constant stress rate). It is also interesting to note that the mechanical behavior of individual elements in the model appear to reflect the different stages of brittle fracture in rocks (Bieniawski, 1967), namely; crack closure, elastic deformation, stable fracture propagation and unstable fracture propagation.

Jan 1, 1986

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are sometimes large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy/Bureau of Mines- sponsored subsidence study currently underway at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County), West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar retreat mining. The initial findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water bevels at shallower depths.

Jan 1, 1985

By BEN WANG, HAORAN LI, YALI FENG, JINRONG JU

Acidic wastewater is at present directly neutralized with lime or limestone, which wastes resources such as titanium, scandium and iron and generates a great deal of solid waste. This study proposes a novel approach for the separation and recovery of titanium, scandium and iron from acidic wastewater, and utilization of red gypsum. The proposed process not only recovers valuable metals from acidic wastewater but also treats the red gypsum that has previously been dumped.

Aug 1, 2022

By P. Koh

A novel approach incorporating computational fluid dynamics (CFD) and flotation modelling has been used for investigating flotation cell designs. CFD modelling has increasingly been employed to enhance understanding of the cell hydrodynamics in mineral and coal flotation. Opportunities for improving the flotation cell performance can be identify by modelling. The CFD-flotation model from CSIRO incorporates cell hydrodynamics that affect particle-bubble interactions. Information from the model includes velocities, turbulent dissipation rates, gas hold-up, particle-bubble attachment and detachment rates. The attachment and detachment rates have been found to be effective measures of cell performance for cell design.

Jan 1, 2011

By R. Mensah-Biney

The NC State University Minerals Research Laboratory (MRL) and Waste Reduction Partners (WRP) of the Land of Sky Regional Council joined efforts in 2000 to initiate a technically sound and practical program for the management of high-volume coal combustion by-products (CCBs) in North Carolina. The accumulation of CCBs from coal burning boilers throughout the state of North Carolina posed a substantial storage problem, and the area was overripe for an effective management program, which would be environmentally sustainable. In particular, the public utility generators had filled storage ponds on their properties, and the storage overload had grown to critical proportions. Much the same situation existed for paper mill biosolids, which were stored on site in landfill cells along with daily output of CCBs from the mill boilers. A conversion process via the patented pyro-process12 (US Patent No. 5,342,442) to produce synthetic light weight aggregates (LWA) from CCBs and paper mill sludge was conceived to process large quantities of both these waste materials. MRL and WRP initiated and formed a consortium that brought together academia, private industry and state agencies to evaluate the production of LWA by the pyro-process. The industry partners included representatives from the power companies, industrial ash generators, expediters for coal ash products, as well as concrete block manufacturers. It was important to welcome interested parties from not only the western North Carolina area and other parts of the state but also from neighboring states including Tennessee, South Carolina and Georgia. Membership of this consortium evolved during the intervening years to include the following participants and supporters: Progress Energy Carolinas; Duke Energy; Santee Cooper; Full Circle Solutions; Land-of-Sky Regional Council; NC Department of Pollution Prevention and Environmental Assistance; Ecusta Business Development Center; Blue Ridge Paper Products; Jackson Paper and Manufacturing Company; Miller Perlite; Appalachian Products; General Shale Brick; Metromont Materials; Small Business Technology Development Center of the University of North Carolina system and North Carolina State University The initial development program conducted at the Minerals Research Laboratory (MRL) was to formulate an acceptable LWA product, which fulfilled user specifications for light weight concrete block and structural concrete application. Support work and program coordination efforts were furnished by retired technical volunteers in WRP. The work advanced steadily, using proven technologies well established in the mineral industry, to generate a very satisfactory LWA. The consortium then concluded that a more comprehensive CCB conversion program would have more appeal for full scale manufacture and commercialization, if a variety of products from CCB separation were generated. This product assortment would include bottom ash, low carbon fly ash, recovered carbon of high purity, as well as the synthetic LWA. The bottom ash would serve the concrete block market, the fly ash was in demand for ready-mix concrete, and the high carbon product could be pelletized and used as a fuel for reburn or by the steel industry, and the LWA was a sought-after component for light weight concrete applications. After scouting all these potential markets and finding them to be viable, the consortium then inaugurated an integrated pilot plant program for the CCB separation and conversion. The plan was organized in three (3) parts: (1) Phase I ? bench scale evaluation studies (2) Phase II continuous pilot plant evaluation and (3) Phase III ? conceptual commercial plant design including marketing efforts and attraction of business entrepreneurs to build a full scale manufacturing plant. Phase II would serve to validate the process in a continuous mode and produce substantial quantities of products for preliminary marketing efforts and for demonstration-of-use purposes. The consortium agreed to the name, CAROLINA ASH PRODUCTS, (CAP), for the integrated pilot plant program. The products generated might be designated with the CAP label as: bottom ash would be named CAP Granules, low carbon fly ash would become CAP Ash, recovered high carbon product would be CAP Carbon, and LWA would have the name CAP Stone. Phase II of the program processed 20 tons (18 t) of ponded ash from Progress Energy storage at a rate of 600 lb (271 kg) of raw ash per hour with favorable results. PRELIMINARY STUDIES Prior to committing laboratory research and development effort as well as support and coordination activities to this program, it was necessary to determine (1) the level of need for a freshly launched CCB reutilization program in this state and (2) what degree of versatility was necessary for such a process. State agency records and a survey of recent boiler operations indicated that in the state of North Carolina at least 77 facilities manage CCBs from their boiler operations. Despite continuing development efforts in more eastern parts of the state, the use of CCBs for commercial applications has not increased to a level which alleviates the need to store vast quantities in private monofills on the generator?s property. More than 1.25 million tons (1.13 million t) of CCBs are landfilled in NC annually, with 300,000 tons (271,985 t) per year generated in western NC alone. Many different boiler types, which span both very old units and those that are modern and efficient, were to be found. These included stoker-fired units, pulverized coal boilers, slag-tap furnaces, and fluidized bed combustion boilers covering a range of sizes. Any systems designed to separate CCB components from all these sources and convert them to useful secondary products would need broad processing latitude and flexibility. Up to the present there has been a paucity of research done in the western part of the state to find productive alternatives to storage in landfills. With tipping fees in our largest landfill now approaching $40 per ton ($44 per t) and escalating transportation fees (about $200 per truckload up to 40 tons, traveling a distance of 25 miles), the problem has become urgent both economically and ecologically. A well-designed, integrated wet process for CCB separation into value-added products had much potential to be less expensive than landfilling as well as to provide saleable materials with acceptable profit margins. These preliminary investigations also revealed that other major waste streams, in particular paper mill sludge and municipal and animal waste biosolids were important candidates for priority attention. Since these biosolids could furnish the organic component of a synthetic LWA product, they could be consumed as part of the same program. This added interest value to a growing list of partners to support and participate in the program.

Jan 1, 2009

By Q. Yuan, B. Yarar

Steric stabilization is a phenomenon observed when relatively high doses of flocculants are added to fine particle suspensions. Experiments were conducted to establish conditions under which medium viscosity and the sedimentation properties of black sand components in a slurry could be controlled so as to enhance the selective sedimentation of gold grains. It was shown that black sand concentrates containing as low as 2.65 g/mt gold could be upgraded by selectively hindering the sedimentation of non-gold components in an aqueous slurry. This paper presents data describing the theory and practical implementation of this cyanide or mercury-free novel approach where gold could be concentrated by as much as 15 times with relatively high recoveries. The relationships of solids content of slurries, type and dose of polymers with the recovery process are documented. Key words: Gold, black sand, selective flocculation, steric stabilization.

Jan 1, 1993

By R. K. Mehta

An accurate, efficient and stable computation of the mill matrix function (eAt) is needed where mill matrix (A) is a real general matrix. Two important modeling cases in comminution where such need arises are: Heterogeneous comminution behavior of multi-component ores and ultra-fine grinding involving simultaneous attrition and fragmentation breakages. This paper presents the application of a novel splitting method in conjunction With similarity transformation technique in the form of "product formula" which is found to work in all cases and uses a most aggravating, yet interesting property of the matrix exponential in a restricted sense. Results are presented showing that this method can yield solution as accurate as those obtained With an analytical technique. The utility of this computational approach is demonstrated by parameter estimation analysis using a distributed component model in the liberation area through computer simulations.

Jan 1, 1992

By Dan Martz, Stuart Lipofsky, Dean Workman

"The Indianapolis Deep Rock Tunnel Connector (DRTC)—first in a vast network of storm water storage tunnels below Indiana, USA—was a wildly successful endeavor. Crews for the Shea/Kiewit JV drove a 6.2 m Robbins Main Beam TBM to world record rates. The machine achieved 124.9 m/day, 515.1 m/week, and 1,754 m/month in limestone and dolomite rock. The advance rates can be attributed to many factors including ground conditions and knowledgeable crew, but continuous conveyors are also of key importance. The novel conveyor system, manufactured by The Robbins Company, enabled continuous tunneling in a difficult layout that included two 90-degree curves and two S-curves. Spanning 11,777 m in its longest iteration, the system included nine booster drives plus a main drive. A vertical belt moved muck up the 76 m deep shaft to a radial stacker for temporary storage. The system, one of the most complex in North America and the first to operate in 90-degree curves, made swift tunneling possible. This paper will examine the world-class tunneling done at the Indianapolis DRTC and the role of continuous conveyance in reaching high advance rates. The logistics of the system will also be examined as it could apply to future tunneling projects with similarly complex layouts. INTRODUCTION The Indianapolis Deep Rock Tunnel Connector (DRTC) is the first phase of a nearly 28-mile long network of deep rock tunnels being built 76 m beneath the City of Indianapolis, Indiana by Citizens Energy Group. The Deep Rock Tunnel Connector (DRTC) Project is a 12.2 km, 5.5 m diameter tunnel constructed by S-K JV, a joint venture between J.F. Shea Construction and Kiewit Infrastructure Co. The tunnel is a $179 million project and is the first segment and southernmost portion of a deep, large diameter conveyance and storage tunnel system to provide overflow relief during wet weather events. The project is estimated to be completed in 2017 and will initially deliver 204,000 cubic meters of the planned 1 million cubic meters of CSO storage for treatment, as well as provide future connections to other tunnels in the overall system (see Figure 1)."

Jan 1, 2016

By J. Scheepers, P. Smith, G. (Yunfei) Qiao

High pressure acid leach (HPAL) and pressure oxidation (POx) or pressure leaching extraction processes occur in autoclave vessels operating at elevated temperature and pressure, acidic conditions with abrasive mineral slurries. The harsh process conditions require specialized severe service metal seated ball valves to support operation of the vessels. Over several decades thermally sprayed titanium dioxide (TiO2) and chrome oxide (Cr2O3) coatings have been applied to extend the service life of the ball valves and other high wear critical components. Variability in the coating application quality control and severe process conditions can result in spalling, coating failure and premature failure of the component resulting is decreased autoclave circuit availability. In 2012 MOGAS, together with BRENCO, initiated research and development for ML-381, metallurgically bonded coating. This paper includes the historical development of severe service ball valve coatings, success of the trials and increasing industry adoption of the ML-381 coating for ball valves and other critical autoclave circuit components.

Mar 2, 2022

By G. Atesok, M. S. Celik, G. Onal, I. Yildirim

A new coarse cleaning device, the Stripa, has been developed for processing of coal in the size range of -100+10 mm. The Stripa is an auotogenous heavy medium separator originally developed for processing of iron ores. Although it has been employed in concentrating ores such as chromite, it has not been applied in coal cleaning. In this study, a pilot plant scale modified Stripa and its counterpart alternative, a diaphragm jig, are compared using subbituminous and lignitic coals. The separation performance of the Stripa and the diaphragm jig has been established in the light of washability properties of the coal samples. Comparison of the performance of the Stripa with that of the jig indicates that the Stripa can be used in coal preparation circuits as an alternative to jigs in the size range of -100+10 mm. Simplicity, low initial investment, and low operating and maintenance costs make the Stripa a plausible candidate for coarse coal cleaning. More importantly, Stripa due to its short residence time, has a superior capacity over jig.

Jan 1, 1995

By B. K. Parekh

Sludge obtained during production of magnesium (Mg) metal from electrolyzing of molten MgCl2 contains entrapped magnesium particles. The sludge material containing the magnesium particles is a friable, continuous matrix of frozen salt mixture which may also contain some oxides and impurities. A dry process was developed for recovery of magnesium metal from the sludge, utilizing minerals beneficiation unit operations. The steps included selective comminution, screening, attritioning and tabling. Recovery of the high grade (+90 percent) metal was in the 70 percent range. The process is being commercially used in the U.S. The novel process was also successfully applied to a magnesium-alloy for recovery of metal from the sludges.

Jan 1, 1995

By K. G. Tan

Widely available silver and arsenic bearing concentrates can be smelted to produce a discardable slag, a base metal speiss, and a crude silver button which is easily separated from the other phases after solidification. This paper discusses the development of a novel process as an alternative to existing nitric acid leach methods for the production of high purity silver from the raw silver button. Direct electro-refining of the raw silver anode in a sulphate medium is integrated with downstream purification and recycling modules that are customized to allow efficient recovery of silver and saleable by­products. The test results, flowsheet alternatives and process details are presented and discussed in terms of overall technical feasibility, economical viability and environmental compliance considerations.

Jan 1, 1999

This paper presents the results of an experimental study undertaken to demonstrate the feasibility of using silica sand as a grinding media in stirred ball mills for ultra-fine coal grinding. Laboratory batch as well as bench scale continuous tests indicate that the use of silica sand can reduce the energy consumption by 50% and more over its steel media counter-part. Moreover, this approach has been found to eliminate the disadvantages observed with grinding using steel media such as high replacement cost, contamination of coal through media wear, greater degree of coal oxidation due to higher slurry temperature and greater level of noise dissipation. Additionally, coal-sand attrition system reduces the manpower time required which is often spent towards cleaning and storing of steel media in inert atmosphere to avoid rust and corrosion problems.

Jan 1, 1991

By Rein Buisman, Michael Fullam

This paper outlines the general operating principles, benefits and applications for the Pansep Screen. The Pansep is a continuous fine screen developed in 1997 capable of processing high volumes of fine mineral f actions continuously, and at small apertures.

Jan 1, 2000

By K. E. Hjelmstad

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air, rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine, fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage.

Jan 1, 1989

By L. Boyd, T. Martin, V. Gall

Water infiltration into subgrade infrastructure can cause major impacts on their performance. In addition to damaging the structure, water intrusion leads to deterioration of installations including electrical and mechanical components and in patron discomfort. To remedy these impacts, leak remediation is often carried out to halt water infiltration. Remediation methods include coatings, drainage, injection/stitch grouting, curtain (backside) grouting, and/or internal umbrella systems. Selection of the rehabilitation method depends on the structure’s use, owners’ priorities, its installations, structural conditions, surrounding ground, and hydrogeologic conditions. Since many factors influence the rehabilitation method chosen, a novel holistic approach is undertaken to understand leakage causes and consequences to develop the most appropriate, efficient, and reliable solution to extend the structure’s life. A reconnaissance phase combines geologic, hydrogeologic, and as-built information with detailed digital scans and visual observations to develop a database of existing conditions. This database, called a tunnelband, is used to develop the rehabilitation solution and made part of the contract documents, allowing for an informed bid by specialty contractors. Tunnelband and the preferred rehabilitation system are portrayed in contract documents, which are procured in various contract types depending on the owner’s preference and project characteristics. The pool of contractors are required to submit their understanding of this holistic approach by developing and supplying the owner with a detailed workplan. The completed rehabilitation is portrayed in detailed as-built drawings which also provide the owner with an operation and maintenance manual outlining for periodic observation of the structure and checking of its performance. Ultimately, this information is implemented into a “BIM Digital Twin” that is used by the operations and maintenance staff for long-term observations. This proposed novel framework for leak rehabilitation is currently being used successfully in a number of projects throughout the United States.

Jun 13, 2023

By Arash Nikvar-Hassani, Lianyang Zhang

To address the drawbacks of the conventional portland cement/fly ash (PC/FA)–based cementitious material currently used in practice to construct pumpable roof supports (PRSs), a novel cementitious material has been developed based on geopolymerization technology. The novel cementitious material is comprised of two pumpable grout streams: Stream 1 is a slurry composed of pozzolanic material and high-calcium additive and stream 2 is an alkaline solution comprised of a gelling agent. Biopolymer has been added to the second stream to provide ductility to the geopolymer cementitious material. In the laboratory scale, systematic experiments have been carried out to investigate the viscosity, setting time, and uniaxial compressive strength (UCS) of the new cementitious material and develop the right recipe for field applications. By collaborating with industry and the National Institute for Occupational Safety and Health (NIOSH), full-scale PRSs have been constructed and tested. The results show that (1) the novel cementitious material based PRSs has much higher peak UCS and similar or higher residual strength than the conventional PC/FA-based PRSs; and (2) unlike the PC/FAbased cementitious material, the novel cementitious material shows good long-term durability with nocracking/disintegration when exposed to air.

Jul 1, 2023

By Hilal Soydan, H. Sebnem Düzgün, Jurgen Brune

In this study, with the primary goal of capturing ongoing digital transformation and automation impacts on the mining industry and its workforce, we conduct several interviews with mining industry experts in the United States and analyze our survey reports qualitatively and quantitatively through exploratory analysis. After the interpretation of the insights of industry experts, we proceed to generate a personalized and customized data analysis through a novel metric based on skills, knowledge, competencies and occupational requirements, which quantifies the job similarities for occupations in the mining industry based on the publicly available database of the U.S. Department of Labor. We use text analytics to tokenize and classify the interviews to capture a better understanding of major response categories. The temporal analysis shows that the critical competency needs in the data science and autonomy category increases from 28 percent in current demands to 43 percent. In defining our metric, we also calculate Kullback–Leibler (KL) divergence for each job profile that enables determining whether and to what extent that job is transitionary in our test set based on the mean, standard deviation and kurtosis of each job of interest. Our analysis reveals that the in-group job transitions are significantly easier than the between-group transitions, proving our initial assumptions and common sense. The generated heat maps provide the opportunity to present the gap between the current job and desired job profiles that provide feasible career change options, among others, offering individualized career paths for job seekers and promoting potential job transitions. Through the collection of industry-specific individual employee data, the AI system is envisaged to continue to learn as end users engage with the system, thus creating a central data hub specifically for the future workforce in the mining industry. Although the study has limitations on generalizability for qualitative assessments, it presents itself as a valuable application of how qualitative and quantitative approaches could be of value for future worker training in the mining sector.

Feb 1, 2025

By J. P. Hedlund

Molycorp's gravity type panel-caving operation employs a system of short raises to transfer ore from the Grizzly Level to the Haulage Level. The raises have normally been developed using a conventional drill-and-blast method or a combination conventional/raiseboring method. A new method was needed that would be less labor intensive, provide a safer work environment for personnel, provide a stable raise that could be self-supporting and a method that would be cost competitive with the conventional system.

Jan 1, 1991