Search Documents

By D. K. Denton, M. J. Friedel, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep ( > 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Feb 24, 1997

By William E. Horst

Ore grindability data based on various techniques to measure comminution characteristics are used to evaluate the crushing and grinding efficiency in mineral processing operations. The importance of achieving improved comminution efficiency, in terms of energy consumption, has been emphasized by recent increases in the cost of electricity. From a theoretical standpoint, the objective of a grinding operation might be expressed as maximizing the production rate at a given grind size while minimizing the energy consumption per ton of material ground. To achieve this objective in an industrial operation presents a challenge especially in view of changes in the raw material which are normally encountered. Various procedures1-5 used to determine energy-size parameters and grindability measurements have been reported. The proposed relationships between particle size and energy consumed have much in common between many of the techniques for measuring grindability. Probably the most widely used parameter to measure ore grindability in recent years is the Bond work index6, Wi, which is defined as the kw-hr per ton required to break from infinite size to a product size of 80 percent passing 100 microns. If the breakage characteristics of a material remain constant over all size ranges, then the calculated work index would be expected to remain-constant since it expresses the resistance of material to breakage. However for most naturally occurring raw materials differences exist in the breakage characteristics depending on particle size, which can result in variations in the work index depending on grind size. Consequently work index values are generally obtained for some specified grind size which typifies the comminution operation being designed or evaluated.

Jan 1, 1975

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines is completing a Feasibility Study for a new open pit gold mine in north central NV. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing open pit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled, and unscheduled random events during the period under analysis.

Jan 1, 2006

By W. M. Aubrey

The use of solid fuel in shaft furnaces to indurate iron ore pellets was originally considered a necessary evil, which the industry worked long and hard to eliminate. Since then changes have taken place in furnace design and operating practices that have led us to our suggestion that solid fuel additions could again be used. In essence, what has happened is that the developments which made it possible to operate without solid fuel have also created new operating conditions favorable to the effective use of solid fuel. Because these new conditions* were brought about in part by the desire to eliminate solid fuel and because the development was a gradual one, the industry failed to reassess its position and for years neglected the possibility of returning to solid fuel.

Jan 1, 1967

By Charles E. Mongan

The problem of roof control in the coal-mining industry is of major importance inasmuch as 65 percent of all coal-mine fatalities result from falls of roof, face, or ribs. The Health and Safety Research and Testing Center of the Federal Bureau of Mines at Pittsburgh, Pa., is engaged in several programs directed toward increasing safety in coal mining. The Roof Control Research Group has 4 programs aimed at reducing roof fall accidents. One of these programs is the use of sonic techniques to explore mine roof strata.

Jan 1, 1961

By M. M. Carpenter

Specialty chemicals are widely used in the industrial minerals process industry for many different purposes including beneficiation, filtration, flocculation, dispersion and biological control. Optimal use of such chemicals can confer benefits both in terms of cost efficiency and end product attributes. In this paper we will review recent progress in the fundamental understanding of mineral additive interactions and present data which show how optimization can lead to improved products.

Jan 1, 1999

By Malte J. M. Gurgel, Axel Preusse

The planning, construction, and monitoring of underground storage facilities is a key factor in meeting upcoming challenges as part of the energy transition from fossil fuels to renewables. Therefore, the many years of knowledge and expertise in ground control gained from coal mining are highly valuable for new mining and storage operations. For such applications, our previous work examined cavity registration, combining structure from motion and LiDAR through a case study in a former lead ore mine. Building on this, the results of this recent case study are discussed regarding the possible application in sites for nuclear waste disposal in Germany including a view on the situation in the United States. Photogrammetric methods are particularly suitable as part of long-term monitoring, which relies on both precise survey results and a large variety of detailed visualization. In order to gain a better understanding of the resulting application potential for holistic monitoring, both existing repositories sites in Germany and ones yet to be found are examined. This search and selection process for high-level nuclear waste disposal is studied in detail together with rules resulting from the (German) mining law, regulations, and other guidelines. Hereby, key requirements of photogrammetric products like oriented images, point clouds, and three-dimensional (3- D) models are identified for different case studies. The findings on accuracy and integrity of the generated models are not only of interest for future repository sites or underground pumped storage power plants, but also offers various possibilities for underground mining of coal and other commodities.

Jul 1, 2023

By P. W. Conrad, C. Todd, N. West, R. Kramer

"Surface subsidence caused by both underground room-and-pillar mining operations and solution mining operations have each been studied separately, but never combined. In 2008, FMC Minerals began using solution mining at its Westvaco Mine as a secondary extraction method in an area that had been previously mined using the room-and-pillar mining method. Mining regulations require that subsidence associated with underground mining activities be monitored and measured annually. Researchers at Montana Tech were able to develop a relationship between measured surface mine subsidence and solution mining that can be used at the Westvaco Mine to estimate the production of trona from solution mining operations. PROJECT BACKGROUND FMC Minerals (FMC) has increased the production of trona from its Westvaco Mine near Green River, Wyoming, using solution mining as a secondary extraction method in an area previously mined using the room-and-pillar method. The area of interest was mined until 2001 with the use of a borer miner at a depth of approximately 1,600 feet. Currently, FMC determines the amount of trona produced using its solution mining operations by measuring the dissolved solids pumped from the mine. This approach, however, does not account for the location from which the trona was removed. The location from which the trona was removed and the size of the cavern created by the solution mining operations is important to FMC’s mine planning. FMC believed that with proper investigation of the subsidence at the Westvaco test site, a correlation might be found that would allow for the use of surface subsidence measurements to estimate the amount and location of trona production from the solution mining activities. The primary goal of this project, conducted by Montana Tech, was to find a relationship between the measured subsidence and the solution mining activities. The project attempted to model the relationship between the measured subsidence and the solution cavern using Salt_Subsid, an existing subsidence software package from the Solution Mining Research Institute (SMRI), to determine the program’s usefulness for locating and developing the cavern created by solution mining activities. The project also attempted to develop an equation that could be used to predict solution trona production based on measured subsidence. The data used in this study were collected over a seven year period, 2008 through 2014."

Jan 1, 2016

By P. W. Conrad, C. Todd, N. A. Degerstrom, N. West, R. Kramer

"Surface subsidence caused by underground room-and-pillar mining operations and by solution mining operations have been studied separately but never in combination. In 2008, FMC Minerals began using solution mining at its Westvaco Mine as a secondary extraction method in an area that had been previously mined using the room-and-pillar mining method. Mining regulations require that subsidence associated with underground mining activities be monitored and measured annually. Using Salt_Subsid, a subsidence software package from the Solution Mining Research Institute, and ArcGIS, Esri's mapping platform, researchers at Montana Tech were able to develop a relationship between measured surface mine subsidence and solution mining that can be used at the Westvaco Mine to estimate the production of trona from solution mining operations. Project backgroundFMC Minerals has increased the production of trona from its Westvaco Mine near Green River, WY, using solution mining as a secondary extraction method in an area previously mined using the room-and-pillar method. The area of interest was mined until 2001 with the use of a borer miner at a depth of approximately 488 m (1,600 ft). Currently, FMC determines the amount of trona produced using its solution mining operations by measuring the dissolved solids pumped from the mine. This approach, however, does not account for the location from which the trona was removed.The location from which the trona is removed and the size of the cavern created by the solution mining operations are important to FMC’s mine planning. FMC believed that with proper investigation of the subsidence at the Westvaco test site, a correlation might be found between surface subsidence measurements and the amount and location of trona production from the solution mining activities. The primary goal of this project, conducted by Montana Tech, was to find relationships between the measured subsidence and the solution mining activities. The project attempted to develop an equation that could be used to predict solution trona production based on measured subsidence. The project attempted to model the relationship between the measured surface subsidence and solution mining production using Salt_Subsid, an existing subsidence software package from the Solution Mining Research Institute (SMRI, Clarks Summit, PA) to estimate the location, size and shape of the solution mining cavern. This study would determine the program’s usefulness for locating and developing the cavern created by secondary solution mining activities. The subsidence and production data sets used in this study were collected over a seven-year period from 2008 through 2014."

Jan 4, 2018

By S. Corrent, F. A. V. Guimarães, M. G. Barbosa

"INTRODUCTION Moisture can be a villain, so new technologies have been explored to make more viable the production of high moisture iron ores. The current work presents the attempt of the utilization of a superabsorbent polymer (SAP) to aid in the screening process and in the ore handling process, such as stockpiles reclaiming and vessels/trains discharge in sub-zero temperature conditions. The results have shown that the polymer can be used in certain cases to improve productivity and increase safety in the process of handling the material (by increasing the TML). However, for size separation no advantages were found upon the use of the polymers. WATER ADSORPTION MECHANISMS The use of water in mineral processing is constant as its utilization brings an increase in the efficiency of separation. Although we have better results in the processing with water, materials with a high content of “natural” moisture can be very difficult to be treated by the conventional methods of separation. Nowadays many studies have been conducted in order to understand the effect of adsorption of water in the particles of complex minerals. Those studies have being divided in many different lines of research such as contact angle of a drop of water and the surface of the mineral to determine hydrophobicity, the particle size distribution and the porosity of particles. Mainly two forms of adsorption of water by the particles are possible: one the water is retained inside porosity of the particles. Laboratory tests developed in China have showed that capillary adsorption is faster in coarser particles that achieve the saturation degree earlier than finer particles (Xuewei Lv et al., 2011). The so called non-porous model considers the effect of water in the bulk sample of iron ores, in a physical connection when all the water works as a binder between particles as shown in the figure 1.If we take into account the compressibility of the system and compaction due to the weight of the bed over the particles, the thickness of the water film between particles is the same but the volume inside different particle size systems is much higher than in a system with particles of same size."

Jan 1, 2018

By J. W. Wilson, Y. P. Wang, M. H. Erten

The use of water is still the most effective and economical means for dust control in underground coal mines today along with dilution by the ventilation current. Studies have shown that the dust capturing capacity of water is a result of a balance of many intermolecular forces. Surfactants are known to reduce such forces by affecting both the surface tension of the liquid and its interfacial tension against a solid. Surfactants can be added to the water sprays to facilitate the dust capturing capacity. A laboratory scale model has been developed in which surfactants were added to the spraying water and preliminary data indicates positive results.

Jan 1, 1991

By Rebecca S. Stanevich

BACKGROUND Diesel exhaust is an animal carcinogen, although evidence of the carcinogenicity in humans is "limited". (World Health Org. , 1989) Of the eight cohort studies in the 19808, five found an increased risk for lung cancer among workers who may have been exposed to diesel exhaust (RR from 1.3-1.5, SMR from 101-132). (Howe, et al., 1983) Only two studies accounted for smoking indirectly. Of the ten case-control studies in the 1980's, eight reported increased risk of lung cancer among those populations purportedly exposed to diesel exhaust. (Benhamou, et al. , 1988) All but one of these adjusted for smoking and other occupational exposures. The odds ratios ranged from 1.2 to 2.1. In two of these studies, miners experienced a two to three fold risk. (Benhamou, et al., 1988) Bladder cancer has also been linked to diesel exhaust in cohort and case-control studies. Excesses of approximately 50% were observed among truck drivers in studies by NCI. (Hoar, et al., 1985) In the National Bladder Cancer Study, risks for truck drivers rose with duration of employment. A study by NIOSH in Ohio also found an excess of bladder cancer among truck drivers, particularly among those with 20 or more years of employment. (Steenland, et al, 1987) Despite the large number of studies in which the relation between diesel exhaust exposure and lung cancer has been examined, exposure to diesel exhaust has been quantitatively estimated only in the studies of railroad workers and truck drivers. (Woskie, et al., 1988) The excess lung cancer risk experienced by workers in these two occupational groups was modest, ranging from 40 to 90% for those with long-term employment. However, diesel exhaust exposure among railroad workers and truck drivers is lower than that seen among miners. Several markers of diesel exhaust have been utilized in these studies. Diesel exhaust is a complex mixture of particulates, vapors and gases. One group of these gases, the nitrogen oxides, react with polynuclear aromatic hydrocarbons, forming mutagenic and possible carcinogenic nitrated derivatives. (World Health Organization, 1989) For this reason, and because it is easy to measure and analyze, NO, was frequently used as a marker of diesel exhaust exposure. As part of the Garshick (Garshick, et al., 1988) study of railroad workers, Woskie measured NO, exposures of 477 railroad workers. (Woskie, et al., 1988) Geometric mean exposures of 13 job groups ranged from 12 to 80 ppb. In a New Mexico potash mine, (Attfield, et al. , 1982) exposures of from 100 to 3300 ppb nitrogen dioxide

Jan 1, 1992

By W. R. Reed

The National Institute for Occupational Safety and Health (NIOSH) uses light-scattering dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer, was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By W. R. Reed, W. J. Archer, A. B. Cecala, J. D. Potts

The U.S. National Institute for Occupational Safety and Health (NIOSH) uses light-scattering real-time dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer (i.e., with cyclone and pump configuration), was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By O. E. Brown

The measurement principle of the Coulter Counter for particle size analyses is described. The application of the Coulter Counter to cement particle content and size analysis and to the size distribution of clinker from standard grindability tests are described. Methods of calibration, sample preparation and data reduction are presented. The results of the analyses obtained are compared with characteristics associated with performance showing both concordance and non-concordance of test data., Future uses of the Coulter Counter for particle size analysis in research and plant control adaptations are indicated.

Jan 1, 1960

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Respirable crystalline silica (RCS) found in dust generated by various mining processes is an important occupational hazard in the underground coal-mining industry. Exposure can lead to disabling and incurable diseases, including coal workers’ pneumoconiosis (CWP), silicosis and lung cancer [1,2]. Clusters of rapidly progressive CWP have been observed in the Appalachian regions of eastern Kentucky and southwestern Virginia, and recent cases have been generally more severe and showing more rapid progression. CWP is approximately four times as common among long-tenured underground coal miners in central Appalachia than long-tenured underground miners in the rest of the United States, and 20.6 percent of long-tenured underground miners in central Appalachia were suffering from the disease as of 2017.

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Exposure to respirable crystalline silica (RCS) can cause serious and irreparable negative health effects, including silicosis and lung cancer. Workers in coal mines have the potential of being exposed to RCS found in dust generated by various mining processes. The silica content of respirable dust in one single mine can vary substantially over both time and location. The current monitoring approach for RCS relies on the use of traditional air sampling followed by laboratory analysis. Results generated using this approach are generally not available for several days to several weeks after sampling, and this delay prevents timely and effective intervention if needed. An alternate analytical method is needed to reduce the time required to quantify the RCS exposure of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has developed a new method using commercially available portable infrared spectrometers for measuring RCS at the end of the sampling shift. This paper will describe the application of the new field-based RCS analytical process for coal mines, including the use of the new method with the existing Coal Mine Dust Personal Sampler Unit. In a case study conducted by NIOSH with a coal mine operator in West Virginia, field-based RCS analysis was completed at a mine site to evaluate the new technique. The RCS analysis results obtained by the field-based method in this case study showed sufficiently strong correlation with results obtained by the MSHA standard laboratory analysis method to allow the mine operator to use the field-based method for evaluating process improvements.

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Exposure to respirable crystalline silica (RCS) can cause serious and irreparable negative health effects, including silicosis and lung cancer. Workers in coal mines have the potential of being exposed to RCS found in dust generated by various mining processes. The silica content of respirable dust in one single mine can vary substantially over both time and location. The current monitoring approach for RCS relies on the use of traditional air sampling followed by laboratory analysis. Results generated using this approach are generally not available for several days to several weeks after sampling, and this delay prevents timely and effective intervention if needed. An alternate analytical method is needed to reduce the time required to quantify the RCS exposure of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has developed a new method using commercially available portable infrared spectrometers for measuring RCS at the end of the sampling shift. This paper will describe the application of the new field-based RCS analytical process for coal mines, including the use of the new method with the existing Coal Mine Dust Personal Sampler Unit. In a case study conducted by NIOSH with a coal mine operator in West Virginia, field-based RCS analysis was completed at a mine site to evaluate the new technique. The RCS analysis results obtained by the field-based method in this case study showed sufficiently strong correlation with results obtained by the MSHA standard laboratory analysis method to allow the mine operator to use the field-based method for evaluating process improvements.

By Keith G. Wallace, Malcolm J. McPherson

In order to model accurately a mine ventilation system in an existing mine, it is necessary to determine the resistance to airflow in all main airways. This is accomplished by measuring the airflow and pressure differential in each airway. Gauge and tube methods have been used to determine pressure drops in ramps and level airways. However, it has rarely been used in evaluating the frictional pressure drop in shafts. Because shafts commonly have the highest pressure loss in mines, it is critical that the resistance of these airways be determined accurately. This paper describes the theory and practice of using the gauge and tube method for determining the pressure drop in shafts. The pros and cons of using this method are discussed as well as a comparison between the gauge and tube and barometer measurement techniques. Case studies showing the accuracy of shaft gauge and tube measurements are also presented.

Jan 1, 1991

By S. Shaw

There is an increasing requirement for mines to meet a certain minimum criteria for sustainability within the context of the physical environment, ecosystem and socio-economic system in which they are located. The mining industry has wrestled to develop methods for assessing the ‘sustainability’ value of a mining project and indicators of ‘sustainability success’. A methodology for the evaluation of sustainability of a mining project using the Multiple Accounts Analysis (MAA) system was developed. The MAA is a platform for engagement of stakeholders and for the assessment of site-specific alternatives based on both qualitative and quantitative indicators of success.

Jan 1, 2004