Search Documents

By K. E. Yassin, A. Yehia, M. Amar

Phosphate ores are the source of many commodities, such as phosphorus element, P2O5 and fertilizers. Discarding a large percentage of fine phosphate particles produced as slimes during phosphate ore processing represents a severe environmental problem, besides making the beneficiation process uneconomical. The phosphate industry is interested in a process that is efficient, with high grade and high recovery; ensures economical feasibility, with low operating cost; and is environmentally sound, with low toxicity. Numerous investigations have been conducted to try to find better processing techniques and reagents. However, reagent requirements and recovery limitations may be so high that the end does not justify the means. Reagents of biological origin are of special interest because they offer specific interactions with minerals, reduced operating costs, environmental acceptability and flexibility in adaptation. Recently, there has been a growing interest in using microorganisms as flocculants for mineral fines and as flotation collectors. 

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By M. S. Celik

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, boron minerals, colemanite, ulexite and borax undergo respectively decrepitation (fragmentation), shrinkage and expansion upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot plant studies on calcination of boron minerals conducted in our laboratories are reviewed along with their implications in commercial operations.

Jan 1, 1997

By R. Elias

Botswana is a mining-dominated sub-Saharan country. Workforces are characterised by poorly educated operators and front line supervisors, with equipment and management to 1st World standards. Poor communication, ignorance of business objectives, inability to meet targets, and lack of problem-solving capacity are the norm. Training leads to high expectations and is of concern to management as a source of dissatisfaction, despite the long-term benefits higher skills have for mine viability. The aims of a technical training programme are presented with various models and approaches being implemented at operations in Botswana. These are used to construct a series of guidelines for technical training initiatives.

Jan 1, 2000

By Joseph Clare

It’s not the 1960s anymore. Upgrading wastewater pipelines in the current era demands the latest trenchless technology to minimize impacts. King County Wastewater Treatment Division in Seattle, Washington is designing a nearly mile long Direct Pipe® influent sewer combined with microtunneling to replace a 1960s era trunk sewer constructed along and within Coal Creek and its natural area. Trenchless installation using Direct Pipe® and microtunneling was chosen due to reduce impacts to residential neighborhoods, natural creek environments, and the constraints of topography

Jun 13, 2021

By F. J. Klingler, K. M. Swaffar, M. M. Rabbaig

The Detroit Water and Sewerage Department has undertaken a $1.2 billion effort to capture and treat combined sewage overflows from various outfalls along the Detroit and Rouge Rivers in Detroit, Michigan. This program is planned to include a 455,000 m3 (120 million gallon) storage and treatment tunnel which will capture overflows from 19 outfalls along the Rouge River. The tunnel is currently in the conceptual design phase, with the bid date planned for mid-year in 2001,and completion planned for August 2005. The total design and construction cost is currently estimated to be approximately $450 million. Current concepts are for the storage and transport tunnel will be 6.1 m (20feet) in finished diameter, with a total alignment length of approximately 12,200 m(40,000 feet). The main tunnel will extend through the Traverse and Antrim Shalerock formations, while approximately 5,500 m (18,000 feet) of various diameter connecting tunnel will extend through both rock and soft ground. The project will include a total of 10 drop shafts, 13 riser shafts, various connecting structures, and a 455,000 m3/day (20 mgd) pumping station. This paper will present a discussion of the design philosophy, subsurface conditions, the various planned components, and the expected design and construction considerations for the proposed Upper Rouge Combined Sewage Overflow Tunnel.

Jan 1, 1999

By Wern-ping Chen, Jean Habimana, Jinyuan Liu, Mirza M. Rabbaig, Robert Barbour

To mitigate and control the combined sewer overflows from 17 outfalls in the City of Detroit, three outfalls in Dearborn Heights and eight outfalls in Redford Township, the Detroit Water and Sewerage Department has completed the preliminary design of a storage tunnel in 2005. In 2006, a final design has revised the alignments and the inside diameter (ID) of the tunnel. The revised tunnel system includes an 11.28-km(7-miles) 9.14-m (30-ft) ID tunnel, a 24.4-m (80-ft) ID pump station, two work shafts about 15.2-m (50-ft) ID each, and 14 drop shafts with various IDs. This paper discusses the latest development of this tunnel system.

Jan 1, 2007

By George Weinman

GEORGE WEINMAN: Our first group leader for the discussion, "Ups and Downs of Downsizing," wishes to remain anonymous. ANONYMOUS PRESENTER: When George and Jamie asked me to do this, I thought a while about what to say and went through several variations of what I’ll present today. I came up with the title "Ups and Downs of Downsizing." A lot of downsizing has occurred in all of our industries-mining in particular. While this downsizing has gone on there's no doubt that all of us produced more and more, probably with less and less people and less and less resources. But I contend that there's also a big downside associated with this. I disagree with a point made in the keynote presentation yesterday, the point being that vendors are bringing new technology to us. I can agree that the major changes associated with equipment and similar items are being brought to us by vendors. But I do contend that there's an awful lot that's getting away from us-especially if you factor in the integrated supply or the strategic alliance or the various and sundry related purchasing techniques. I contend that we are missing a lot of, let's call it, lesser technology; not major equipment changes, but different tools, different techniques for doing things, different left-handed widgets. The integrated suppliers, to some degree, are bringing this to us; but I am concerned about the small guy who comes up with a good idea but deals through integrated suppliers rather than having direct contact with plant people. They're probably going to go somewhere else and market their wares. That's what I'm hearing from a lot of smaller vendors. I also think that we are losing a lot of our knowledge base. Every time you shrink an organization somebody leaves. The bottom line: less people. When a person leaves-and I don't care who he or she is, be it the janitor who's cleaning the bathroom, the operator, the engineer-when that person leaves there's some knowledge that goes with that per- son. And sometimes that knowledge is quite valuable. I've worked more or less at the plant "low." I can't tell you how many excellent, viable projects have come from people who said, "Look here. There's a better way of doing this." And, you know, they were right. Now, maybe they didn't have the resources or the expertise to develop these ideas into full projects, but they had that basic idea. Someone may say, "Well, if we put a no. 6 skyhook here, so we can lift this particular pump without bringing a crane from 30 miles away ...." No. 6 skyhooks are a bit expensive, but what if we put together a little structural steel here or whatnot?

Jan 1, 1998

By M. Sandin

According to the world bank1, the mining industry consumes up to 11 percent of global energy use. In comparison, 70 percent of mining projects from the six largest mining companies operate in water-stressed regions. To steer the direction of the process industries toward more sustainable practices, more than 40 governments have adopted a price on carbon. This measure includes additional taxes on the use of fossil fuels, trade programs, new standards for renewable energy, energy efficiency mandates, more stringent emissions regulation, carbon offsets, etc. This emphasis is also supported by investors shifting their priorities to reduce risk by focusing on long-term plans, including environmentally friendly operations. The metals and mining industry is at the core of the green energy mix and electrification of vehicles. This new trend creates an astronomical increase in demand for minerals. Under a 2-degree scenario, according to the latest analysis from the world bank, as new energy technologies continue to grow, it is expected that all minerals to double in demand, and the distribution of these materials will depend on their application. • Solar panels, will account for 87% of the aluminum demand, and more than 95% of silver • Wind turbines and geothermal plants will require 98% zinc and 64% titanium. • Solar and wind energy alone will demand more than 74% of the global supply of copper, and this is without considering wiring or other infrastructure to connect the grid • Battery storage accounts for 100% of the graphite and lithium demand. (Hund, 2020) • Other materials, such as nickel and steel, are also projected to more than double in demand as they are cross-technology minerals. These materials require a manufacturing process that is accountable for the emissions proper of the transformation process. It requires that these processes move from a hindsight mode focused on reporting to a forecasting mode based on run-time measurement of GHG emissions. This is a critical first step in companies realizing an economic return for doing the right thing for the environment and their communities.

Feb 1, 2023

By George Joseph Malina

Contractor chose and Owner allowed concrete to be placed using the arch first principle while excavating the 35'-3" O.D. rock tunnel. The contract included excavating and lining 26,000 L.F. of rock tunnel to 33'-I.D. Concrete was placed at a rate of 90LF per working day using a movable bridge to allow batching, mixing and pumping of concrete adjacent to the tunnel form.

Jan 1, 1981

By Takashi Sakaguchi, Takehiko Tsuruta, Akira Nakajima

Some attempts were made to recover gold from aqueous systems using immobilized persimmon tannin. This adsorbent adsorbed gold from solutions containing hydrogen tetrachloroaurate (III) with high efficiency, whereas there was minimal adsorption from solutions containing gold (I) sodium thiomalate and sodium dicyanoaurate (I). The adsorption of gold was rapid, and was affected by the pH of the solution, temperature, external gold concentration and amount of adsorbent. Adsorbed gold was easily desorbed with 1 M thiourea solution, indicating that immobilized persimmon tannin can be repeatedly re-used for the recovery of gold using adsorption-desorption cycles.

Jan 1, 1995

By F. M. Doyle, C. V. Diniz, A. H. Martins

A proposed process for the direct production of battery¬grade Mn02 leaches manganese ore with HCl to remove heavy metals selectively. The acidic manganese chloride solution produced is contaminated with Cu, Ni, Co, Pb and Fe at levels that preclude immediate utilization. This paper reports on screening tests to measure the uptake of Cu, Ni, Co, Pb, Fe and Mn from acidic chloride solutions onto different chelating ion exchange resins. Dow M-4195, which contains the bis-picolylamine,functional group, showed promise for detoxifying manganese chloride process solutions. Column ion-exchange tests demonstrated the ability of this resin to produce pure manganese chloride solution from an acidic manganese chloride leach solution contaminated by Cu, Ni, Co, Pb and Fe.

Jan 1, 2000

By André Vervoort

At the 2017 ICGCM-conference in Morgantown, WV, a case study was presented with measurements of the upward surface movements or uplift after the closure of two neighboring coal mines (Winterslag and Zwartberg, Belgium). One was closed in the sixties, and the other closed in 1988. The study was based on satellite data (Radar-interferometry or InSAR). The analyses showed both a significant variation of uplift values above the mined area and the surrounding zones, and a variation of the uplift rate as a function of time. In other words, the phenomenon of uplift is complex. At that time, it also was clear that more research was needed to better understand this phenomenon, e.g., an identification of the various mechanisms that are relevant for the process of uplift and the quantification of the various impacts. A systematic analysis of all relevant parameters resulted in a framework that forms the basis for the analytical calculations of uplift values. These calculations show that the main impact is due to changes in the hydrostatic pressure. However, the expansion of the softest parts, i.e., the collapsed or goaf material, is not only important, but the expansion of the (stiffer) non-collapsed strata layers due to a change in pore pressure also must be integrated into the model. For the case study, the partial flooding of the underground after closure of the mine that was abandoned in the sixties is integrated into the model. Larger stiffness values also are applied for this mine, in comparison to the values of the more recently closed mine. Overall, a very good correlation is observed between the InSAR-measurements and the calculated values along a north-south transect.

By J. McMurray

Introduction Uranium was recovered from mining of collapse breccia pipe deposits in the Arizona Strip district in northwestern Arizona (Figure 1) intermittently between 1956 and 1990, with cumulative production having totaled 23.3 million pounds of U3O8 (8960 tU) at an average grade of 0.6% U3O8. Production was suspended in 1990 because of low uranium prices, but the recent resurgence in market price once again makes the breccia pipe deposits potentially attractive exploration and development targets. This paper describes: (1) formation of the pipe structures and their metallogenesis; (2) mining and milling of breccia ore; and (3) potential roadblocks to development of new breccia pipe mines. Breccia Pipe Formation Formation of the breccia pipes began in cave systems formed during development of karst topography in the Mississippian Redwall Limestone. The karst Redwall surface was eventually covered by up to 900 meters of shallow marine to continental sediments ranging in age from Pennsylvanian to Triassic. The pipes were formed by progressive upward stoping caused by groundwater ascending under hydraulic head along near-vertical faults, joints and fractures. The stoping process involved both chemical disaggregation and mechanical failure of roof and wall rock. Upward stoping of successively younger units allowed for upward propagation of a pipe and resulted in a chimney-like column of breccia between the steep walls of the pipe. Syndepositional thickening of sedimentary units of varying ages indicates that pipe formation began as early as early Pennsylvanian time and continued intermittently through Triassic time.

Jan 1, 2007

By Richard H. Kennedy, G. A. Swanquist, John W. King, Frank F. McGinley, Dale C. Mathews, Hans H. Adler, E. C. Peterson, Ralph M. Wilde

INTRODUCTION From the first historical records of the discovery of uranium as an element and the attempted classification of its minerals in the early 18th century-through its first uses in pigmentation and the coloring of glasses and ceramic glazes-until 1939 when it was discovered that the isotope U235, was fissionable, uranium oxide in the form of pitchblende ores and concentrates (produced mainly in Bohemia, Canada, and the former Belgian Congo) in recent times was the source of uranium compounds incidental as byproducts to the recovery of radium from this invariable associated source. In 1938 this byproduct production from pitchblende concentrates was about 471 st of U3O8, with over 90% from Canada and the Belgian Congo and only 25.85 st from carnotite ores in the United States.1 Under the impetus of the Atomic Energy Commission's (AEC now part of the Energy Research Development Administration) domestic and foreign production incentives and buying programs, and as an initial assurance of atomic armament capability of the United States and the Free World, the growth of the uranium mining and milling industry burgeoned from 1952 to 1962. After a short period of decline, in the second decade and in large commitments beyond, it has again extended its capacity to meet ever-increasing fuel demands of atomic power generation by the electric utilities industry. In 1961 the peak production in the United States alone was 17,758 st of U3O8. Peak aggregate domestic and foreign deliveries of 34,581 st of U3O8 to the AEC occurred in 1960.z Canada's maximum delivery of 13,506 st of U308 was made in 1959. These peak and continued productions in the Free World are largely from: the Mesozoic (Jurassic) and Tertiary (Eocene) sandstones in the United States; the quartz pebble conglomerates of Canada and the Witwatersrand; pegmatites, Jurassic limestones, and Precambrian complexes, with less but significant production; the phosphoria, where byproduct production is minor. This uranium production in the form of precipitated concentrates has come from the milling of ores from these sources, both directly and by retreatment of gold cyanidation tailings on the Witwatersrand. Milling of crude ore has followed these processes: conventional crushing and size preparation, ore drying when required, salt roasting for high vanadium ores and byproduct vanadium recovery, carbonate or acid-leaching processes, classification sand-dine separations or countercurrent decantation (CCD) circuits and complete liquid-solids separations, resin-in-pulp (RIP) or liquid-liquid (solvent) ion-ex- change extractions, clarification of pregnant liquors, precipitation, filtration and washing, sodium and vanadium removals, and drying or roasting and packaging of the high-grade, high-purity uranium concentrate commonly referred to as "yellowcake." Coupled with the hazards and control of dust generation incident to conventional crushing and milling operations, more stringent control of airborne respirable and ingestible radioactive particulates and the protection of personnel against definitive external radiation are inherent to uranium milling. Impoundment and control of tailings and other effluents of uranium milling are more restrictive than in conventional practice, be- cause long-term disposal and containment of the uranium series of radionuclides, whether in solution or in solid form, are requisite to uranium milling and are made manadatory under regulatory agencies of government. 2. GEOLOGY AND MINERALOGY OF URANIUM Early Uses and Byproduct Production of Uranium Uranium was discovered by Klaproth in 1789 but had little commercial importance until the discovery of uranium fission by Hahn and Strassman at the close of 1938. The well-known uranium ores of Joachimsthal, Czechoslovakia, the Congo, and the Colorado Plateau were early sources of radium. Minor quantities of uranium were used for small-scale technical and industrial applications, particularly in coloring glass and ceramics, but most of the uranium was discarded. The Colorado ores were also mined later, chiefly for vanadium. Impetus of Armament Capability and Fuel Demands for Atomic Power Following the discovery of atomic fission, uranium became critically important for military applications and, more recently, as a nuclear fuel. Prior to 1966 uranium was acquired in the United States almost solely for use in the weapons program of the AEC. By 1970 the AEC had procured approximately 325,000 st of U3O8 from domestic and foreign sources. Current and future marketability is primarily dependent upon commercial demand for reactor fuel. Estimates of

Jan 1, 1985

By C. Slotta, F. Charlier, P. Blomen

"Within the energy concept of the German government, the operating time of nuclear power plants was initially extended from about 8 to 14 years. It is planned, however, that every power plant will gradually be decommissioned until 2025 and that simultaneously the amount of renewable energies will successively be expanded. According to the political state, nuclear energy is a discontinued model. Looking at the global energy market, though, an obviously opposed development can be observed. At the moment, 443 nuclear power plants are running worldwide and further 62 facilities are being built. These about 500 nuclear power stations have to be supplied with nuclear fuel right now and in the future. The present paper will describe the worldwide use of nuclear energy, the extraction of the nuclear fuel uranium and in detail the available and predicted resources of uranium. The conclusion of the paper is the statement that uranium as nuclear fuel is no scarce resource but sufficiently available."

Jan 1, 2011

By Hetland Donald L.

Regional Tertiary formations and basins of local sedimentation which contain uranium deposits west of the Rocky Mountains are mainly of Oligocene, Miocene, and Pliocene age (fig. 1). The host rocks have been derived mainly from intrusive and extrusive igneous rock. The major host formations which cover broad geographic areas include the Esmeralda, Truckee, Humboldt, Thousand Creeks, Payette, Panaca, Cedarville, Coso, and San Joaquin Formations. Local areas of Tertiary sedimentation containing uranium deposits occur near Yuma, Safford and Artillery Peak, Arizona; Dillon and Canyon Ferry, Montana; Spokane Indian Reservation and Pend Orielle River, Washington; Topaz Mountain, Utah; Stanley Basin, Idaho; and Sonora Pass, California. Uranium deposits in these sediments have been classified into five categories based on environment (fig. 2). They are: (1) Deposits in lake sediments consisting mainly of water-laid tuffs; (2) Deposits in lake sediments intruded by volcanic plugs; (3) Deposits in lake sediments interbedded with arkoses near batholiths; (4) Deposits in coarse volcanic sediments in local sedimentary basins; (5) Deposits in arkosic conglomerates in local sedimentary basins.

Jan 1, 1969

By John B. Squyres

The purpose of this paper is to describe certain features of the uranium deposits of the South San Juan Basin, and to suggest a mode of origin for the deposits which is consistent with the data. A series of photographs is included at the end of the paper to illustrate the nature of the ore bodies. Since the general geology of the Grants Region is well described in the literature, it will be only briefly reviewed, and the time will be spent instead on the morphology, spatial relations, and geochemistry of the ore deposits. Part of this material is original, but data and ideas have been taken from a variety of sources, including the literature and the personnel of the USGS, the AEC, and many of the operating companies of the South San Juan Basin. I gratefully acknowledge these sources. The accuracy of the data and the conclusions presented here are my own responsibility, however.

Jan 1, 1974

By Ravindra M. Chhatre

Uranium associated with phosphate deposits has been the subject of numerous investigations (1-8). In the land-pebble phosphate deposits of central Florida, uranium is found in the phosphate matrix (ore) and in the leached zone between the over-burden and matrix (1). Between 0.01 to 0.02 percent uranium is found in the leached zone, which consists of apatite and aluminum phosphate minerals (crandallite, wavellite, millisite) (Z). The primary phosphate mineral in the matrix is apatite, and the 0.005 to 0.01 percent uranium typically found in the matrix is associated with this mineral (1). It is generally believed that uranium substitutes for calcium in the apatite structure (3-5). Clay and quartz phases associated with phosphate deposits contain little uranium (1, 6), and no descrete uranium minerals have been detected in these deposits (4). A typical phosphate matrix consists of quartz, slimes (-150 mesh material) and recoverable phosphate. When the matrix is beneficiated, partition of uranium and radium takes place (9, 10). Although considerable data exists on how uranium is distributed in the phosphate deposits, no systematic study has recently been reported on the distribution of uranium during phosphate rock beneficiation. The purpose of this study was to determine how uranium is distributed in the various strata which comprise the overall land-pebble phosphate deposits, as well as how the uranium is redistributed during beneficiation of phosphate matrix. To obtain this information studies were carried out on matrix samples obtained from three different mines in central Florida. Using pilot-plant scale beneficiation, an analysis was performed on how uranium in the matrix is distributed among the pebble fractions, flotation concentrates, flotation tails, and slimes. The uranium level profile for an active mining area was also obtained. Also, since thousands of acres of slime ponds may someday become a source of both phosphate and uranium, a depth versus uranium content profile was determined for an inactive slime pond.

Jan 1, 1978