Search Documents

By R. Stocker

Flotation recovery of molybdenite particles finer than 15 micrones sharpy decreases with decreasing size. A totally hydrophobic latex agglomerant (UBC-1), which was previously reported to be very efficient in agglomerating hydrophobic fine coal, has been found to agglomerate fine molybdenite particles. The agglomeration takes place only in the presence of MIBC which is commonly used as a frother in molybdenite flotation. Adsorption tests confirmed that MIBC is adsorbed onto molybdenite. The effect of the agglomeration on flotation has been studied by floating fine molybdenite from mixtures with quartz using the UBC-l agglomerant and the MIBC frother. A significant improvement in the flotation of fine molybdenite has been observed in the presence of the UBC-l agglomerant. The best results have been obtained around pH 5.5 which corresponds to the iso-electric-point of molybdenite.

Jan 1, 1997

By Hassan El-Shall, M. N. Ahmad, Ponisseril Somasundaran, C. R. Holland, G. M. Walker, N. Iles, R. D. Chandler, Regis Stana, B. Duddy, Patrick Zhang

Phosphoric acid is a major raw material for the production of ammonium phosphate (AP) that is used as an intermediate in fertilizer production. Impurities within commercial grade wet process phosphoric acid are important in producing a fertilizer granule with good handling properties. The impurities identified as being important are; iron (III), aluminium and fluorine-containing compounds. Results show that the viscosity of the AP slurry produced increases by increasing the amount of impurity in the acid. Bench scale tests have been successfully replicated on a plant scale leading to a better understanding of the composition of impurity levels within phosphoric acid required to produce a high quality, free flowing, hard, spherical and non-caking granular fertilizer.

Jan 1, 2002

By T. S. Spicer

Inflammability and crossing point apparatuses were used to study the influence of increasing amounts of such inerts as ash, fly-ash, pyrite, limestone and Portland cement with several pulverized bituminous coals. The results indicate that it requires large proportions of inerts to substantially suppress the ease of ignition.

Jan 1, 1962

A large lab apparatus was designed using a scale-down methodology based on the design legacy of the current FLSmidth commercial forced air flotation machines. This new apparatus, along with a new test methodology, was used to evaluate new rapid prototype concepts. The apparatus was designed to monitor bubble size, power, pumping capacity, Jg, velocity profiles, froth character, and tip speed. The methodology developed follows a sequence that goes from hydrodynamic tests and solids suspension tests to a flotation kinetic test. This methodology has been demonstrated to be a good tool to determine the effect of machine design changes on flotation.

Jan 1, 2012

By K. Oraee

Proven and probable coal reserves in Iran are estimated to be in excess of 5 Billion tons while the annual coal production is a mere 2 Million tons. Underdevelopment of the industry has proved higher production levels to be impossible, despite growing demand for energy supplies. The existences of numerous legislation are thought to have a detrimental effect on coal mining activities to the extent that some business entities have become uneconomical in many areas. This paper provides an analysis of the prevailing mining laws, policy making, legal frameworks and obstacles. It also outlines some other obstacles enshrined in the law and also highlights areas where foreign direct investment should be encouraged. The costs of lost opportunities are then estimated. The paper concludes by demonstrating that deregulations, amendments and in some cases complete abolishment of the incumbent legislations governing the coal mining industry will greatly enhance development of the industry. The analysis provided in this paper together with the results obtained, can prove useful to macro-economic policy makers both at local and national levels.

Feb 27, 2013

By K. Kavouridis

The competitiveness of power production from lignite depends on the ability of coal industry to meet CO2 emissions limits, as specified by the Kyoto protocol. According to the National Allocation plan issued by EC, power plants should reduce CO2 emissions to a certain level, other-wise they will be obliged to cover the difference buying CO2 certificates through the Emission Trading Scheme. These charges will increase the operating cost of current units, as well as the investment cost for new units. To predict the increase in the marginal cost of electric power produced from the current plants of Western Macedonia, an emissions factor (CO2 t/MWh) for various units has been computed. Based on the algorithm used, this factor depends on the calorific value of the lignite, the efficiency of the power plant and the oxidation factor of the unit. For lignite plants with efficiency ~37%, CO2 emissions factor ranged from 1.19 t/MWh to 1.32 t/MWh. The increase in the marginal cost of kWh, as compared to the values of CO2 certificates, is higher in units fed with low quality lignite and worsens if the efficiency of the unit is low too. Also the presence of calcareous minerals in lignite increases the CO2 emissions and consequently the cost of power generation.

Jan 1, 2006

By H. A. Kortmann

For the commercial production of iron ore pellets from hematite ores, as it is practiced in various pellet plants, the addition of lime has shown to be an efficient means with a view to improving cold compression and abrasive strength of the indurated pellets considerably. Unfortunately, it has also been shown at the same time, that the metallurgical properties as, for instance, swelling behavior, softening during reduction under load and disintegration of the grain, can be adversely affected to a high degree. In the course of smelting tests carried out by renowned steelworks, blast furnace operation was heavily disturbed by the swelling and early softening of the pellets, also by their disintegration in the low-temperature range, which altogether led to a considerable lowering of the smelting rate (1, 2, 3).

Jan 1, 1972

By Glenn A. Hazen

Longwall mining is the preferred method for removing underground coal since a larger amount of coal can be removed faster and with less waste when compared to the room-and pillar type mining. Thus, the coal tonnage removed each year by longwall mining methods has increased dramatically. However, a high extraction rate results in surface subsidence which has adverse effects on the environment and on surface structures. Predictions of structural damage are dependent on the magnitude of the expected horizontal strains. Three methods for predicting subsidence characteristics are considered in this paper: the graphical method, the profile method, and the finite element method. All three methods can be used to predict ground movements and horizontal strains. However, the finite element method, which takes into account the structural properties of the stratigraphy and equilibrium of the overburden, is theoretically the more logical choice for use in subsidence prediction.

Jan 1, 1987

By Prakash Venkatesan, Mehmet Ali Recai Ӧnal, Shaik Saida, Veerendra Singh, Chenna Rao Borra, Manish Kumar Kar

A laboratory-scale investigation of the effect of milling operation and catalyst addition ( K2CO3) on the partial reduction of low-grade pyrolusite ore pellets was carried out using coke as a reductant. Thermogravimetric analysis was used to understand the correlation between milling and catalyst addition parameters with the reduction temperatures. DTG analysis of pyrolusite pellet reduction showed three distinctive peaks associated with a three-step reduction mechanism (i.e., MnO2→ Mn2O3→Mn3O4→MnO). The results showed that the grinding and addition of the catalyst have a significant effect on lowering the MnO2 reduction temperature independently. But maximum reduction temperature drop is obtained when combining grinding and catalyst addition in this work. By 3 h milling and 10 wt% catalyst addition, the reduction temperatures were reduced by more than 200 °C compared to the raw ore pellets. These results obtained from the DTG analysis were further supported by XRD analysis of the reduced samples.

Dec 20, 2022

This paper reviews the historical literature and the author's experience with regard to the effect that the selection of grinding ball size or sizes has on ball mill grinding efficiency. The conclusions presented provide guidelines for single and multi-size charging prac- tices in commercial milling operations.

Jan 1, 1998

By Augustine O. Orumwense

Ball mills are commonly used for regrinding operations in the mineral processing industry. But, in recent times, efforts are being made at the introduction of stirred mills particularly for those instances where very fine grinding is required. Media type (steel shot, glass beads, alumina balls and crushed quartz), media size, mill speed and the number of passes required to obtained the target product size are studied. The product size and energy consumption are used in the evaluation of the test results. The grinding media size, shape, density, filling ratio, mill circumferential speed and grinding time play a distinct role in product size fineness.

Jan 1, 2005

By Zygmunt Sadowski

Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of chemical additives and metal ions present either added or present as contaminants, on the flotation. Fuerstenau and Palmer (1976) have studied in detail the adsorption of multivalent cations onto oxide and silicate minerals. It was observed that the adsorption of a multivalent metal species exhibits a sharp pH dependence which is related to the formation of hydroxy complexes of the metal ions in solution. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances cations such as Ca2+, Mg2+, Fe2+ and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions.

Jan 1, 1986

By Lana Alagha, Ashraf Alsafasfeh, Amal Al‑Hanaktah

As freshwater resources are becoming scarce, the use of seawater as replacement of fresh water is appealing in order to make mineral processing operations more sustainable. Since froth stability plays a critical role in determining the performance of flotation operations, there is an urgent need to study the effect of frother dosage and seawater on froth stability. In this study, flotation tests in seawater were conducted to examine the effect of frother’s dosage (MIBC) on the froth stability and flotation performance of low-grade phosphate ore. The stability of the froth layer was assessed by measuring the froth growth velocity and the froth maximum height at equilibrium. Results indicated that the best flotation performance was obtained at 75 g/ton of MIBC where ~ 90% of phosphate minerals were recovered. At this recovery value, the concentrate grade was determined to be ~ 70%. Results from froth stability experiments showed that the stability of the froth layer increased by increasing MIBC dosage. At MIBC dosage of 75g/ton, the calculated values of dynamic froth stability and the froth height were ~ 0.4 cm/sec and 16 cm, respectively.

Jan 17, 2024

By H. E. Rojas

The primary objective of most comminution operations is liberation; however, mill performance is generally quantified in terms of particle size. Only recently has the use of image analysis equipment made it possible to quantify mill performance on the basis of liberation. In this investigation, a series of tests were carried out to study the effect of mill operating parameters on the liberation of sphalerite from a sphalerite/dolomite ore. The parameters studied included mill rotational speed, mill loading and ball size. The results of this work appear to indicate that sphalerite liberation is improved under conditions that promote impact breakage, while dolomite breakage is enhanced under attrition conditions.

Jan 1, 1990

By M. Abdi Oskouei

Some believe that Sustainable Mining due to impermanence of mining operation and adverse environmental impacts of mining, is an oxymoronTruly, no one can overlook these environmental impacts; however, a sustainable development is based on three elements Environmental, economical and social sustainability. In order to assess the relation between mining activities and sustainable development, not only environmental but also economical and social sustainability must be considered.Thanks to mine reclamation the adverse impact of mining on the environment can be reduced, meanwhile it will improve the social and economical condition after the mine-closureTo ensure that a mining operation is toward sustainable development goals, specific criteria and indicator frameworks have been established, in addition, for verification of our discussion the suitable selected reclamation plan for Bibishahrbanoo limestone mine of Tehran-Iran and its effect on sustainability of region has been studied.

Jan 1, 2011

By D. R. Lanners

Samples of the same coal measure overburden spoil were obtained from three different mine sites. Site A used a 27-m3 tub-mounted dragline, Site S used a front-end loader and truck combination, and Site C used a 6-m3 crawler-mounted dragline. The spoils were analyzed in the laboratory for the strength parameters using drained triaxial tests conducted on 150-mm diameter specimens. Regression analysis was utilized to determine the appropriate failure criterion for the strength data from each site. Spoil obtained from Site S yielded higher shear strengths than Sites A and C.

Jan 1, 1993

By E Mutaz, M Bahaaddini, D J. Williams, M Serati

The contribution of the mining industry to the global economy has reached (and gone beyond) $1,800 billion in recent years that necessitates (more than before) the need to ensure workability, viability, health, and safety of mine sites and workers to meet the ever-increasing global demand for mineral resources. Amongst the many challenges facing the excavation industries, rockburst and spalling failures in deep mines in hard and brittle rock formations are yet happening that are still deemed as unsolved problems. During unconfined compressive testing of brittle rocks, microcracks initiate at approximately 0.3–0.5 of the peak strength (which is commonly known as the Crack Initiation stress level) mainly in the direction of the major principal stress, then grow unstably and coalesce to form macro fractures at approximately 0.7–0.8 of the peak load at a so-called Crack Damage stress threshold. From a stress-strain perspective, the crack damage stress threshold () is associated with the reversal point of the volumetric strain, which is also proved to be strongly affected by the intermediate principal stress. This paper extends the previous studies on the impact of true triaxial loading conditions on the CD stress level in high porosity rocks, and introduce a new Crack Mode-Changing Stress (CMCS) defined as the minimum principal stress required to change rock fracturing from splitting to a sliding failure mode. A large number of experiments on sandstone specimens were carried out at different true triaxial loading conditions and the effect of principal stresses on the CI and CD as well as CMCS were studied. The results show that not only the intermediate principal stress, but also the minor principal stress can significantly affect the CD and CMCS thresholds.

Apr 26, 2022

"The adsorption of mixed cationic/anionic surfactants with different molar ratios onto quartz was investigated. The cationic surfactant used was dodecylamine bromide (DDA), and the anionic surfactant was sodium oleate (NaOL). The critical micelle concentration values for the individual surfactants and their corresponding mixtures were determined using a platinum plate. The adsorption mechanisms of mixed surfactants on quartz were studied using contact angle measurements, flotation tests and adsorption amount measurements. At alkaline condition, NaOL depresses DDA flotation of quartz without depressing the adsorption of DDA. The molar ratio of mixed surfactants is found to be a key factor in the orientation of alkyl chains and thereby the flotation response of quartz. A mixture of 1/2 or 1/3 DDA/NaOL forms on the surface of quartz when the concentration of NaOL is higher than that of DDA. The adsorption of the mixture decreases the wetting of quartz since the alkyl chains are in chaotically orientation with a conceivable number of head groups directing towards the solution phase. These results provide important insights into the adsorption of mixed surfactants onto quartz surface. INTRODUCTION Froth flotation is known as an effective method of separating mineral particles on the basis of their surface chemistry, specifically their hydrophobicity. [1]. The hydrophobic particles will attach to the bubbles and rise to the top of the containing vessel to form a froth that flows over the lip of the vessel. The hydrophilic particles remain in the liquid [2]. In the process, surfactant is often used as collectors for surface modification in order to change the wetting properties of mineral particles. The primary long chain alkyl ammonium salts are the most widely used as collectors for the flotation of oxide minerals, such as quartz, muscovite, hematite, phosphate and feldspar [3, 4]. Adsorption mechanism of alkyl ammonium salts on oxide minerals has been extensively analyzed [5, 6]. Generally, the ammonium salts are adsorbed through electrostatic interaction of the polar group of the molecules with the surface of these minerals [7]. Despite many obvious advantages of the ammonium salts in low temperature resistance and hard water resisting, however, their unavoidable drawbacks, such as high sensitivity and poor selectivity for slimes, relatively high cost, have limited their applications [8]. In recent years, mixed surfactants have drawn much attention due to their superior physicochemical and surface properties than single surfactants [1, 9-11]. They have been used in many industrial processes such as dispersion/flocculation, flotation, detergent, corrosion inhibition, cosmetics, foods, paints, chemical mechanical polishing, enhanced oil recovery, and nanolithography [12]. Most of the mixed surfactants have synergistic advantage in reduction of the surface tension and critical micelle concentration (CMC); therefore, they exhibit spurious properties, like excellent surface/interfacial activities, and are less expensive than single mixed surfactant systems [13, 14]."

Jan 1, 2016

By Jeffrey R. Kelly, Paul M. Kubera, Richard A. Howk

Mixing of solid-liquid slurries is a unit operation that is widely encountered in the minerals processing industry. Applications may range from simple slurry storage in open tanks to complex chemical reaction systems under extreme conditions of temperature and pressure. The specific process requirements dictate both the degree of mixing required and the type of agitation employed to achieve the desired results.' Many continuous-flow process applications feature tanks operating in series to provide a discrete number of stages and a known residence time for the slurry. Because these tanks operate at a constant level in an overflow mode, the mixer must maintain uniform solids concentration and size distribution throughout the tank; failure to achieve uniformity results in accumulation of coarse solids in the tank, ultimately leading to a process or mechanical failure. Downward-pumping, axial-flow mixing impellers are widely employed to produce uniform solids suspension. The specific impeller type, number, size, and power draw is a function of each given situation. The use of high-efficiency, fluid-foil impellers (Figure I) has evolved as a recognized standard for these flow­controlled applications. Recent small-scale experimentation and full-scale experience has demonstrated that, when uniformity is required, capital and operating expense can be minimized by employing an additional upper impeller pumping in the upward direction.

Jan 1, 1995

The implementation of NAFTA in January of 1994 was expected to have small but beneficial effects for the Mexican economy, mostly through increased investment flows. Mexico's mining industry was especially likely to benefit, as mineral investment funds would be diverted to the now safer Mexico and away from similarly endowed but more risky Latin American mineral economies. The results of the past two years have shown that it is governments and macroeconomic factors that influence investment flows, rather than the fine-tuning of trade flows through so called "free-trade" agreements.

Jan 1, 1996