Search Documents

By H. Maleki

In this paper, long-term measurements in five underground mines are presented to demonstrate how these measurements can be applied to stability evaluations and design of underground excavations. These case studies address both the global aspects of strata response to mining activities as well local ground behavior and support loading. The measurements include static (stress and deformation) and geophysical. Case studies quantify pillar behavior, roof-floor deformation patterns, overburden response, and microseismic activities. Large-scale studies quantify the nonuniform nature of overburden deformation and collapse. Local measurements address yield and stable pillar load deformation characteristics, as well as the performance of support systems under combined axial and lateral loads.

Jan 1, 2002

By R. Q. Honaker

Recent studies conducted at Virginia Tech have shown that ultrafine coal particles can be selectively coagulated and separated from mineral matter without the use of traditional agglomerants or flocculating agents. This technique utilizes hydrophobic interaction forces to induce coagulation of coal particles, while particles of mineral matter are dispersed using pH control. After selective coagulation, the coal coagula can be recovered by a sedimentation technique. In the present work, factors such as pH, particle size, and solids concentration have been examined. A wide range of coal samples have been successfully upgraded using this technique.

Jan 1, 1991

By Joe Maloney, Steve Shadow

Mining conditions at Cyprus Amax's Twentymile Coal Company (TCC) require the use of regenerative conveyors. Regenerative conveyors were first used in the Southwest Mine District and then in the challenging East Mine District. This paper will discuss the development and refinement of the equipment used to brake the regenerative conveyors.

Jan 1, 1998

By Peter Jackson

Over a quarter of a century ago a New Zealand physicist suggested the possibility of detecting coal seam discontinuities by a seismic method carried out underground in the mine workings (Evison 1955). Twenty years ago initial experiments were performed in Germany (Krey 1963). Since then research has continued, notably in Britain and Germany, in order to provide a reliable fault and washout detection system. The National Coal Board of Great Britain has now carried out more than 250 surveys in Britain, France and Australia. The first NCB survey in the U.S., a successful application of the technique to an Ohio coal seam, will be described and the strengths and limitations of the method explained.

Jan 1, 1984

By Alvin W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall as mining showed oreshoots to be more continuous than drilling indicated. The Geophysics Department of Michigan Technological University developed a portable induced polarization drill hole probe with a 3 electrode configuration and a sampling radius of 5'± A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec. intervals and readings are taken every two feet. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the I.P. potential is sampled for 10 ms and recorded. Resistivity (ohm-feet) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous "S" values noted. The low resistivity amygdaloid contains sills of high resistivity basaltic trap. Verified by core logs, amygdaloid-trap contacts could be picked to ±.5' from resistivity alone. Lithologic logs of long steel holes, based' on resistivity, now replaced sludge logging. An "S" value of 30 mv/v was established as the lower limit of diagnostic I.P. effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found.

Jan 1, 1964

By Charles W. Rountree

Industrial Engineering in the industrial world is a relatively new field, having been conceived about the turn' of the century by Frederick W. Taylor, who was not satisfied with the hit-or-miss methods of evaluation and estimation. Through crude Industrial Engineering techniques never before used, he completely changed the bricklaying industry so that work accomplished was more than doubled. To help us better understand what we mean by Industrial Engineering, I think a very simple definition Is in order. Industrial Engineering is a scientific approach to problems in cost, production and operations: and is designed to provide a means of increasing producitivity and reducing costs through standards measurement and standardization of the best methods, practices and equipment, There are many complicated definitions, but pure and simply, it all boils down to providing the means for increasing productivity and reducing the cost. Industrial Engineering has been applied in manufacturing since Frederick W. Taylor?s time and in the last 20 years has grown in stature by leaps and bounds. It is a basic function of successful manufacturing companies and is an accepted fool firmly entrenched in manufacturing organizations. You may know of some successful manufacturing companies that do not employ Industrial Engineers as such, but someone in that organization is doing Industrial Engineering work. They have standards and controls whether they call it Industrial Engineering or not. The manufacturing industry has benefited from this tool; other wise, it would have been discontinued long ago.

Jan 1, 1958

By James E. Lonergan

Linear goal programming is a multi-objective optimization technique where the constraints of a linear programming formulation of a problem are considered as additional objectives. The optimal solution is the one that comes closest to satisfying all the objectives. An interactive computer program was written to utilize this technique in solving the feed blending problem faced by power plants de- pendent on multiple sources of coal supply. This program determines the amount of coal from each supplier to utilize in the blend. Examples of the use of the program in both long and short term coal procurement planning scenarios are given.

Jan 1, 1984

By Dale Brunton, Robert Adams, Michael Dutton

Tunnels and other underground structures are typically designed using ground-structure interaction models instead of traditional structural analysis programs. This allows for the degree of load sharing etween the two odies to e calculated allowing for a more efcient design. hile modern codes outline the use of limit states with factors on applied actions, limit states are not typically compatible with ground-structure interaction models. Consequently, the engineer is left to develop rational methods for incorporating load factors into their analyses. Several methods can be considered, including the Largest Factor Method, Averaging Method, Subtraction Method, and Split Factor Method. This paper discusses the approaches, compares their effects using a case example, and provides a recommendation for designers.

Jun 23, 2024

By A. Masutomi

Although great strides have been made during the past two decades in the reduction of the severity of accidents and injuries in underground coal mining, the number of accidents resulting in disabling injuries and lost time has continued to increase. Looking ahead to the 1990s, the reduction of accidents and incidents typically found in these latter categories should be emphasized in safety training for underground coal mining. Loss control is an approach which shows promise for applications in mine safety training since loss-control strategies focus on the pre-contact stages of an incident rather than on the incident, itself. Applied to safety training, the heightened awareness of personnel to workplace hazards at the pre-contact stages should result in a reduction of accidents and injuries. This paper explains the concept of loss control and shows how it can be applied in the development of the needs assessment for miner training programs. An example, based on research conducted at the continuous-miner worksite, is provided.

Jan 1, 1991

By C. C. Graham

In this paper, the problems which occurred on introduction of dense medium cyclone coal washing in Australia are reviewed together with the subsequent measures taken to obtain a satisfactory magnetite. Specification and testing of magnetite for exploration, quality control and in-plant check purposes is discussed. The disposition of Australian magnetite deposits in relation to the main coal producing areas is examined, and comments are made on the economics of mining, milling and beneficiating magnetite for coal preparation uses alone. Future trends in the Australian Coal Industry are predicted, and the need for a planned approach for the future is demons traced.

Jan 1, 1982

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

1.1 GENERALIZED METHODS OF SUPPRESSING THE INFLOW OF GROUND WATER DURING THE CONSTRUCTION OF SHAFTS, DRIFTS AND TUNNELS Various methods are used to prevent or minimize the inflow of ground water into underground workings during their excavation. The two most common methods include freezing the saturated rock and grouting using cement, sodium silicate, polyurethane and/or other chemicals. Each of these technologies for combatting the inflow of ground water is effective only under specific hydrogeological conditions. For example, although the freezing of saturated ground is among the more universally adopted methods, it is designed to provide only temporary protection during construction. Before the saturated rock thaws it is necessary to emplace a waterproof liner which is labor intensive, time consuming, and expensive. Consequently, freezing is used only in exceptionally complex hydrogeological conditions, namely in those cases where the water-bearing strata consist of unstable rock or the ground water has an anomalous hydrochemistry. The classical grouting of saturated rock, carried out from the surface or from the face of the underground workings for the purpose of limiting the inflow of ground water during excavation, utilizes both cement and a variety of chemical grouts. Cement grouting has been regarded as the main method of combatting the inflow of ground water in fractured rock throughout the world. In such countries as the Federal Republic of Germany (FRG), Canada, the Republic of South Africa and Great Britain, cement grouting is the main method of reducing the inflow of ground water during the excavation of mine openings. In Great Britain and the FRG, cement grouting has been used in 80% of all shaft excavations. In the Republic of South Africa cement grouting has been used in almost 100% of all the shafts that have been constructed. The installation of grout curtains into permeable water- bearing strata significantly reduces their permeability and increases the rock strength. Grouting has the greatest effect in fractured sandstones, certain well indurated shales, fractured granites, fractured quartzites, and karstic limestones or dolomites. The following principal factors must be considered when assessing the expediency of grouting rock with cement: the geometry of the network of fracture openings, the saturated hydraulic conductivity of the fractured rock, the hydraulic head acting on the water in the rock, and the chemical composition of the ground water. On the basis of the geometry of the fractures and the thickness of each hydrostratigraphic unit, the characteristics of the cement grout are selected. As a rule, the cementing of large fractured zones with high ground water velocities is carried out using inert fillers (sand, mill slag, loam, loess, crushed limestone), special types of cement, setting accelerators, and high cement concentrations in water. Calcium chloride, soda ash, sodium silicate, sodium nitrate, amino alcohols, tin bichloride, trisulphate nitrate, and lumnite are used extensively as the setting accelerators for cement grouts. In the FRG and Poland, special cement injection compounds that embody a mixture of cement and active cement metal salts, water additives and binding substances are being used for the cementing of saturated zones with rapid ground water velocities. These reagents accelerate the rate of structure-forming reactions. In spite of the wide variety of additives used for cement grouts, the effectiveness of the method in large fractures below the water table is either poor or it leads to a very large consumption of cement due to the erosion of the grout through the cracks before it hardens. At the present time, a large number of cement types and brands are being produced by various countries. These variations permit cementing to be employed in a variety of geological conditions. However, both pure cement grout and grouts with fillers constitute unstable systems with a high water loss rate. Therefore during the grouting of finely fractured rock the cement grout's premature loss of a large amount of free water causes its consistency to increase, whereupon the grout solidifies. Consequently, it inadequately penetrates into the fine fractures of the stratum. In addition the high water loss rate in the cement grout causes unreacted cement particles to remain, which greatly reduces the grout hardness and the resulting rock strength characteristics are weakened. As a result, the binding properties of the cement are utilized perhaps up to 60%. The remaining portion is left in the grout as a filler. All these conditions significantly decrease the efficiency of the isolation effort both with respect to strength and cost. In order to expand the cement grouting method, re- search is being conducted to improve the quality of cement grout, to increase its range of application with respect to permeability control, to reduce its water loss rate and to increase its capacity to withstand the erosive and corrosive effects of poor quality ground water. For example, mixtures of bentonitic clay, carboxymethyl cellulose, aerated sodium sulfide, sulphated alcohol distillery waste, nitrolignin, gip-

Jan 1, 1993

By Neil E. Izatt, M. Andre de Ruijter, Ronald L. Bruening, Wesley Young

IBC Advanced Technologies, Inc. has developed ligands, ?amed SuperLig®, which have specific applications in the gold mdustry. These ligands use molecular recognition technology (MRT). One ligand has been developed to selectively recover gold and silver from tailings solutions and from pregnant Merrill-Crowe solutions. Another ligand removes free cyanide, _ th10cyanate, other cyanide species, as well as copper and other base metal cyanide complexes from leached gold-ore solutions. The development of these "species selective'' SuperLig® prod­ucts allows for the more efficient operation of gold recovery processes and opens up the possibility of the economic devel­opment of high-copper gold ores. The resulting gold eluate is a high grade and a high purity stream which will simplify the need for further refming. Engineered systems based on MRT consist of a few unit operations utilizing standard equipment and mate­rials of construction. The process is simple to operate, thereby lending itself to automated modular design, which is both eco­nomic to manufacture and to operate. Test results for the gold and cyanide-copper systems are presented in order to demonstrate the high selectivity and effi­ciency of MRT technology in recovering these species from solution. . IBC Advanced Technologies, Inc. (IBC) and Fluor Daniel, Inc. formed a strategic alliance in late 1994. The goal of the alliance is to combine IBC's scientific expertise in the MRT field with Fluor Daniel's engineering capabilities in the metal­lurgical industry. IBC has its headquarters in American Fork, Utah, USA, where research, development and manufacturing are conducted. Fluor Daniel is an international engineering and construction firm with head offices in Irvine, California, USA. Engineering efforts for the alliance are centered in the Fluor Daniel Mining and Metals Operating Company office in Vancouver, B.C., Canada.

Jan 1, 1996

By A. T. Sapulek, C. S. Özveren, D. W. Dixon

The prediction of underground methane emission from longwall coal faces has been extensively researched for a number of years and numerous prediction methods have been devised. Many coal mines employ sophisticated environmental monitoring equipment which generates large amounts of data including, methane concentration, air velocity and barometric pressure. Presently this information is mainly used only to indicate alarm and danger levels of the monitored data for management purposes, however, the potential uses of this data are enormous[1]. This information could be used to good effect within a production/methane emission strategy as detailed in a previous paper[2]. The paper presents a practical application of artificial neural networks to underground methane prediction. Data on methane concentration and coal production has been obtained from an underground coal mine. The data is used in a neural network architecture and forecasts of methane concentration have been obtained. The forecasts are examined and there is a discussion of the potential use of the predictions from neural networks in the field of mining production control.

Jan 1, 1995

By Leeming. J. R.

In the UK, powered supports are normally salvaged from longwall faces on completion of production, for reuse on the next unit. Where a spare set of supports are held, the salvaged supports are often stored in underground roadways awaiting installation. One mine in the UK extracts a 5m section, and holds two sets of 2x950t powered supports, each weighing approx. 35t and having closed dimensions of 8m long, 2.5 high and 1.75m wide. As the first set would not be required for over 12 months, and because of space limitations below ground, it was decided that the supports would be left in situ, the district sealed, and reopened at a later date for support salvage. The paper described the decision making process, and the inertisation of the sealed district utilising nitrogen generated on the mine surface and piped to the point of use. The re-entry and re-ventilation of the district are also described. The paper then goes on to describe in more detail the discovery of a spontaneous combustion event that occurred in the waste behind the powered supports, and its treatment and control using extra nitrogen brought to the mine by tanker and introduced at strategic locations along the faceline via boreholes, leading to a successful salvage and re-sealing.

Jan 1, 2009

Introduction The science of geometallurgy requires that ore characterization be performed holistically, that is, with consideration of ore quality on plant performance and product quality. Geometallurgy, by definition, requires knowledge of geology, mineralogy, extractive metallurgy and pyrometallurgy. Examples of the ore characterization challenges for the geometallurgist in the production of iron ore pellets from low-grade Proterozoic iron formation are presented here. Ore Characterization Ore characterization, the quantifying of mineralogy, grain size and the texture of ores, is an often overlooked tool in improving process efficiency. Some mineral related problems are not unique to the production of iron ore pellets; e.g. the problems caused by expanding clays in flotation. The negative impact of carbonate minerals in the ore on pellet productivity and pellet quality are unique. The long and complex geologic history of Precambrian iron formations contribute to modifications of grain size and the introduction of complex textures.

Jan 1, 2007

By V. E. Suter

Anyone with geothermal experience can readily attest that geothermal operations are a natural extension of oil and gas operations. A geothermal company and an oil company need the same type of people to do the same kind of work. In the geothermal industry, geologists and geophysicists define prospects through surface geology, analysis of surface seeps, magnetics, gravity, and resistivity surveys - techniques similar to those used in the petroleum industry. In addition, shallow (250-ft) temperature gradient holes often are used in geothermal operations. Landmen take geothermal leases that are patterned after oil and gas leases. Exploratory drilling is done with the same drilling contractors and same drilling rigs, with minor modification. Drilling foremen and drilling engineers share the same objective of making the most hole, in the shortest time, at the least cost, with a proper completion. Petroleum engineers test the wells, design the completions, determine the reserves, make economic calculations, work with the tax assessor, and manage the reservoirs. Production engineers build roads, locations and pipelines, install gas/liquid separators and meters, and operate production and injection facilities. A contract to sell steam to a public utility is required. Various governmental regulations, permits, environmental concerns, and public affairs pose similar problems in both industries. Also required of both are top management people who are acquainted with geologic risk, prepared to accept million dollar dry holes, willing to bid competitively at lease sales, and able to invest large sums based on a technology not yet fully proven. Successful geothermal development requires in-depth financial ability similar to that required for petroleum development. A high capital investment is required early for leases, geological and geophysical work, and exploratory and confirmation drilling. After

Jan 1, 1980

By V. E. Suter

Anyone with geothermal experience can readily attest that geothermal operations are a natural extension of oil and gas operations. A geothermal company and an oil company need the same type of people to do the same kind of work. In the geothermal industry, geologists and geophysicists define prospects through surface geology, analysis of surface seeps, magnetics, gravity, and resistivity surveys - techniques similar to those used in the petroleum industry. In addition, shallow (250-ft) temperature gradient holes often are used in geothermal operations. Landmen take geothermal leases that are patterned after oil and gas leases. Exploratory drilling is done with the same drilling contractors and same drilling rigs, with minor modification. Drilling foremen and drilling engineers share the same objective of making the most hole, in the shortest time, at the least cost, with a proper completion. Petroleum engineers test the wells, design the completions, determine the reserves, make economic calculations, work with the tax assessor, and manage the reservoirs. Production engineers build roads, locations and pipelines, install gas/liquid separators and meters, and operate production and injection facilities. A contract to sell steam to a public utility is required. Various governmental regulations, permits, environmental concerns, and public affairs pose similar problems in both industries. Also required of both are top management people who are acquainted with geologic risk, prepared to accept million dollar dry holes, willing to bid competitively at lease sales, and able to invest large sums based on a technology not yet fully proven. Successful geothermal development requires in-depth financial ability similar to that required for petroleum development. A high capital investment is required early for leases, geological and geophysical work, and exploratory and confirmation drilling. After

Jan 9, 1980

By Robert Stauffer, John Frostiak, Rein Raudsepp

Placer Dome's Campbell Red Lake Mine in Balmertown, Ontario produces a refractory gold flotation concentrate containing the sulphide minerals arsenopyrite, pyrite and pyrrhotite. In 1991, the existing concentrate roasters will be replaced with a pressure oxidation plant based on Sherritt Gordon technology to update the facilities and to satisfy environmental requirements. A successful continuous pressure oxidation miniplant program was conducted by Sherrill Gordon in late 1989 which formed the basis for the design of the commercial plant. The paper summarizes the Campbell operation and the environmental aspects of the project, and discusses the results of the miniplant program and the design of the commercial plant. The capital cost of the pressure oxidation plant and the process operating costs are also presented.

Jan 1, 1990

By Andrew J. Neale, Brian C. Flintoff

A review of the current literature, combined with the authors' knowledge of the western Canadian coal industry, indicates that the development and implementation of process control in coal preparation, particularly in flotation applications, is significantly lagging behind that seen in mineral processing. The reasons for this include the lack of inexpensive and reliable sensors, incomplete understanding of the flotation process, limited experience of process control in the coal preparation industry and depressed coal prices, all of which have combined to hinder plant automation. This paper illustrates the benefits of process control in coal flotation, provides a general discussion of the control problem and concludes with two examples drawn from Australian experiences.

Jan 1, 1989

By Brij M. Moudgil, Shoulian Zhu, J. L. Pinault

A new technique, prompt neutron activation probe (PNAP), for analyzing phosphate rock slurry in-situ was evaluated both in the laboratory and at the plant. The technique yielded a high precision in the analysis of Ca, Si and H using 252Cf source. Low accuracy of the direct measurement of P using 241Am/Be in the laboratory tests was attributed to the interference of rare earth elements present in the samples, particularly Gadolinium. No significant effect of variables such as solids loading, particle size distribution, and flotation reagents was observed on the probe performance. The probe can detect the compositional changes of the feed, tailings and the concentrate streams in the plant.

Jan 1, 1993