Search Documents

By G. M. (Frits) Swinkels

The Apex property, mined in the early Twentieth Century for direct shipping copper, also contains gallium and germanium in iron oxide minerals. In 1982, Musto Explorations Limited began an exploration program to define reserves. A metallurgical process was developed, and a production decision was reached in late 1983. This text describes the process development and design. The Apex mine, located near St. George in Southwestern Utah is owned by St. George Mining Corporation, a subsidiary of Musto Explorations of Vancouver, B.C. Musto acquired the property in early 1982. A pilot plant was operated by Hazen Research, Inc., Golden, CO later in 1982. In late 1983 sufficient information had been developed for St. George to proceed with the project. The final process design was prepared by G. M. Swinkels of Vancouver, consultant to Musto, and Hazen Research. Process engineering was done by Hazen Research, and St. George acted as its own contractor. Commissioning of the plant began in October 1985.

Jan 1, 1986

By M. Deal

Particle size analysis is a fundamental measurement utilized in the mining industry, especially in comminution, hydrometallurgy, and mineral processing. While sieves and cyclosizers are the standard methods used to determine particle size distributions, in recent years alternative instruments have been developed that claim to provide more rapid and equally reliable results. Newmont Metallurgical Services has implemented the use of two such instruments, along with traditional methods (sieves and a cyclosizer), on a daily basis. The Malvern Mastersizer 2000 laser analyzer is a wet sample system that can analyze particles in the size range 0.02µm to 2000µm, and the Horiba CAMSIZER® is a dry system that can analyze particles in the size range of 30µm to 30mm using digital image processing. A comparative analysis has been performed to determine the applicability of each particle sizing method in laboratory testing.

Jan 1, 2011

By Stuart Ratcliffe, Denis Kidby

The development of Vitrokele™ Technology over the last 10 years is reviewed with reference to mine site piloting and com­mercial applications. The first mine site piloting was conducted in Australia in 1989 followed by a further six continuous site trials in Australia, Canada and the USA. These major pilot plant studies are complemented by over 50 laboratory scale batch and pilot testwork programmes. The first commercial plant using Vitrokele™ Technology was the Connemara project commissioned in Zimbabwe in 1995. Subsequent to this, three commercial scale projects have been designed using Vitrokele™ to recover precious metals, base met­als and cyanide. The various projects are discussed with relation to the differ­ing flowsheets applied to each particular case.

Jan 1, 1998

By A. A. Terchick

In 1970 U. S. Steel acquired the physical assets of mine, mine property, and preparation plant of the Crystal Block Coal Company near Thacker, Mingo County, West Virginia. The facility, identified as U. S. Steel Mine No. 20, is administered and operated as a production unit of U. S. Steel Gary District, Gary, West Virginia. Mining operations of the No. 20 mine are conducted in the high-volatile Alma seam. The preparation plant, which originally had a capacity of about 150 tons per hour (tph) of raw-coal feed, had process circuitry consisting of a Daniels heavy-media vessel for cleaning the plus-1/4-inch raw coal, a McNally-Pittsburg feldspar jig for cleaning the 1/4 inch by 28 mesh, and Daniels flotation cells for treating the 28 mesh by 0. No water-classification system existed. Refuse tailings from the plant were pumped to several surface lagoons which were decanted to the stream. The settled solids were removed and trucked to the coarse-refuse disposal area. Water make-up requirements were supplied by a small mine-water surface reservoir and augmented with stream water. Expansion of production from the property required an increase in preparation-plant raw-coal-feed rate capacity from

Jan 1, 1974

By R. B. Tippin

The material balance computer program (MAT-BAL) developed at the Minerals Resource Research Center of the University of Minnesota, has been used in conjunction with routine process profile samples taken in the potash compaction plant at Great Salt Lake Minerals and Chemicals Corporation, Ogden, Utah. In this manner, a uniform data base is being established for the process, and selected key indicators are used for decisions in plant operation and maintenance. With present emphasis on improving product quality and increasing production rates, the standard data base system provides a means of measuring results from test programs to optimize the circuit. The development and application of this process control method is discussed. The compaction plant computer-assisted data base has been in existence for only two years, but it has made significant contributions to the knowledge of the process and continues to assist in monitoring the plant performance. It is anticipated that the material balance program will be adapted to the GSL flotation plant in 1979, and to other circuits in the potassium sulfate chemical plant.

Jan 1, 1979

By Ian S. Lowndes, Adrian T. J. Moll

With the current trends towards the concentration of extraction to fewer but higher production units in deeper seams, often of higher coal rank, the role of methane drainage ranges has become critical. As mines exploit seams at greater depth and more remote locations there has been a need to extend the lengths of methane drainage ranges and to increase the capacity of the surface pumps. This trend has highlighted the need to effectively simulate the operation of a methane drainage range in order to produce the optimum design and operation of a safe and economic system. This paper describes the development of such an analytical tool. The application of this computer model is illustrated by the analysis of the operation of the drainage system of an extensive mine. The paper concludes by considering the development of a [Knowlege Based or Decision Support System] which will assist the ventilation engineer in assessing the current performance of an existing drainage range and will suggest possible remedial modifications or design strategies which may improve the system performance. INTRODUCTION In order to maintain the general body methane levels to below predetermined statutory threshold limit values (TLV's) on major longwall production units there are, for a given production rate, two major complementary control devices which may be employed by the ventilation engineer. These are the combined design and application of a competent mine ventilation and methane drainage system. The methane drainage system should be designed so as to maximise the capture of the methane (firedamp) from the seam being mined and the strata gas liberated in the vicinity of the extraction zone from gas bearing seams or other reservoirs of gas situated at above or below the mining horizon. The design fresh air quantity entering the face should ensure that under normal operating conditions the methane entering in the vicinity of the face is rapidly dispersed and dilute to well below statutory TLV's. The drainage system must therefore be designed to maximise the capture of the methane gas liberated to minimise the amount of gas which enters the ventilation airstream. GAS DRAINAGE The inherent dangers of methane emissions in mine workings have been a problem of concern to mining engineers for many years. To alleviate the risk, methane drainage has been employed for some years to capture the gas before it becomes a hazard to the operation of the mine. The method of drainage employed will be dependent on a number of factors which include the longwall mining method and production cycle employed, the characteristics of the coal seam being extracted and those of the adjacent gas bearing strata. The location of the gas bearing potential of the over and underlying coal measures must be determined. The gas bearing

Jan 1, 1993

By J. W. Meckenstock

Evidence of the fact that the beneficiation of sand and gravel is now going on is readily observed by visiting various and and gravel plants almost throughout the U.S.A. of necessity this beneficiation process is concentrated more in certain areas than in others, and it is steadily increasing. Therefore, it can be said that beneficiation is now one of the processes inn the manufacturing of sand and gravel, It started some ten to twelve, years ago when the need for beneficiation made itself known, and when the manufacturers of sand and gravel producing machinery began to make equipment available to the industry.

Jan 1, 1958

By Greg Hodges

Sand-and-gravel aggregates have become the number-one, nonmetallic-mineral resource in the world. Surficial aggregate deposits of economic size are becoming increasingly rare in most parts of Canada. In southern Saskatchewan, this is especially true, and detection and delineation of intertill sand-and-gravel deposits with airborne electromagnetic (EM) surveys have proven very successful. Airborne and ground geophysical surveys detect such deposits by their resistivity contrast relative to the surrounding clay-rich soils. Dighem helicopter-borne electromagnetic surveys map soil variations over a large area quickly and cost effectively, greatly reducing the cost of detecting and mapping deposits compared with traditional methods (air-photo interpretation, ground EM, and drilling.). The multiple-frequency EM system used by Dighem can map variations both horizontally and vertically. Magnetic data collected simultaneously are useful in mapping bedrock geology. Both resistivity and bedrock maps aid in the important task of reducing drilling costs and person-hours in the field. The results of the survey are presented as maps of ground resistivity, which are relatively easy to interpret. These maps are produced in the field at the time of the survey, making quick follow-up of the survey possible. Airborne EM surveys can map the extent and depth of aggregate deposits more effectively than is practical from the ground. Since aggregate deposits can vary tremendously in a very short distance (<300 m) large-area EM maps can show both local area variability and also help develop intertill trends. A test survey for the Saskatchewan Highways and Transportation Department over a 3-km by 5-km area mapped all the known deposits as well as some unknown deposits, subsequently proven by drilling. The test-survey data show that the method not only detected the deposits, but also gave an estimate of the shape (volume) of each of the deposits. Comparison of the data to drill sections shows excellent correlation. Theoretical modelling demonstrates that the multifrequency system can discriminate sand and gravel from bedrock ridges. Since the successful test work, about 725 km2 of ground have been surveyed, resulting in the discovery of four new deposits, which can be used immediately, resulting in significant savings for the Saskatchewan government and taxpayer.

Jan 1, 1999

By Ken Takahashi, Yuuich Umeki, Masahiko Arakawa, Dr. Tominaga. Yuusaku

Macroscopic characteristics of a complicated mine ventilation is remarked to build an expert system for mine safety in the Taiheiyo coal mine, Hokkaido, Japan. To gain the characteristics a large number of simulation were performed with varying aerodynamic resistance of the branches with regulator in mine ventilation network. The principal results of the study are as follows, (1) Pressure loss diagram for ventilation network with main and auxiliary fans enables capability of air circulation in the network. (2) H-Q (pressure-quantity) diagram gives capacity of air quantity In a network with main and auxiliary fans. (3) When airflow rate, [] through branch qi is changed by opening/closing regulator set in the branch, air flow rate, [], through branch p can be represented by the empirical formula. [ ] where Api and Qp,o are the constant coefficients. (4) Macroscopic characteristics mentioned above are available to make rules in an expert system for escaping route at emergency.

Jan 1, 1989

The extraction and processing of minerals from surface mines and quarries can produce significant fugitive emissions as a result of site activities such as blasting, unpaved road haulage, loading, primary crushing and stockpiling. Uncontrolled fugitive dust emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. Simulation technology is finding increasing use for the purposes of advanced warning of potential problem emissions in addition to providing a basis for future planning applications where demonstrable compliance with regulatory requirements are necessary. The initial re-entrainment and subsequent dispersion of fugitive dust presents a process complicated by the combination of the in pit topography, the surrounding natural topography and the dynamic nature of emissions from these sites. These factors impact upon the accuracy and reliability of the conventional Gaussian plume based computational prediction methods employed for regulatory compliance and IPPC applications. This paper proposes that optimal modelling of open pit emissions may be more accurately achieved by the use of a multi-scale predictive modelling approach utilizing computational fluid dynamics (CFD) methods for high resolution near source dispersion and conventional Gaussian based methods for far field dispersion modeling. This paper presents a numerical based flow and dispersion analysis of a typical UK based open pit utilizing CFD in conjunction with a conventional Gaussian plume based methods. Typical operating emissions and meteorological conditions are obtained from long term data records collected at a large operating quarry extraction operation in the UK. Emissions are modelled using a Lagrangian framework within conventional atmospheric boundary layer (ABL) profiles expressed as functions of turbulence and velocity parameters under assumed neutral conditions. Results are presented in terms of the impact of site topography on in pit retention as compared to the Gaussian based method.

Jan 1, 2009

By J. McCreedy

The Ontario Division of The International Nickel Company of Canada, Limited, operates five underground mines and one open pit on the rim of the Sudbury Basin located in the Province of Ontario, 230 miles northwest of Toronto. Four of the mines, Frood-Stobie, Creighton, Murray and Garson, lie on the South range of the Basin within a 10-mile radius of the City of Sudbury; the fifth mine, Levack, is on the North range, about 30 miles northwest of the city. The ores are mined primarily for nickel and copper, the principal minerals being pentlandite and chalcopyrite. Other elements recovered from the ores in varying quantities are platinum, palladium, ruthenium, iridium, rhodium, cobalt, selenium, tellurium, iron, sulphur, gold and silver. In 1962, the total underground ore production was over 10,800,000 tons which was mined mainly by blasthole and caving methods with the remainder by cut-and-fill, square set, and undercut-and-fill techniques.

Jan 1, 1964

By Andre Balt, Pierre Hofmeyr

It is only recently that automation has been applied to mining analytical laboratories. This paper describes the use of automation in the laboratory analytical process of hard-rock mining and geological samples and slurries in mining concentrator plant process control laboratories. Types of analysis include fire assay, XRF, ICP and wet chemistry. The benefits of automation are reduced unit cost of analyses, greatly reduced staff requirements, higher quality of data and very fast turn-around times.

Jan 1, 2005

By Chi-shing Wang

In many cases the roof strata of a bedded deposit may be considered as a composite of rock beams of rectangular cross section, whose component layers differ in thickness and may or may not be separable from each other when they are subjected to loading by their own weight. An analytical study of the behavior of such multiple-layer beams is extremely difficult owing to the heterogeneity and anisotropy of rock materials. The complexity is revealed by the fringe photographs obtained from several series of barodynamic photostress experiments conducted on various types of multiple-layer model beams of a medium-grained Bedford limestone. Further discussion on the applicability of barodynamic photostress techniques to the model study of the behavior of mine roofs in stratified geologic media is presented by comparing the phenomenological observations recorded in this investigation.

Jan 1, 1968

By David A. Smith

A new generation of reliable, stable, and easy to use bulk emulsions allowing application in tunneling and drift rounds has been developed. This new product group of bulk emulsions has been especially formulated for use in small-diameter holes and is a significant advancement in bulk emulsion technology. Reliable and easy-to-use bulk delivery equipment has been designed and developed to allow bulk emulsions to be used in a wide variety of shaft and tunneling applications.

Jan 1, 1987

By R. D. Hagni, P. A. Shivdasan

Cathodoluminescence microscopy (CLM) is uniquely applicable to the study of carbonatite-related fluorspar ore deposits. The mineralogy of the carbonatites, sodic and potassic fenites, marbles, quartzites, and fluorite ores are readily determined and characterized. Calcite, dolomite, apatite, fluorite were deposited dominantly under high temperature conditions and they exhibit strong cathodoluminescence (CL). Three types of carbonatites have been recognized at the Okorusu, Namibia carbonatite complex and fluorspar mines by field mapping and laboratory CLM. The main carbonatite intrusion is fine grained and consists mainly of calcite. A later phase of pegmatitic carbonatite consists of calcite, magnetite, Fe-rich pyroxene, apatite, and pyrochlore. Pyroxene carbonatites were recognized mainly through their study by CLM.

Jan 1, 2001

The most common method used for cleaning the fine fraction in today&apos;s coal preparation plants is froth flotation. Past research and practice has found that froth flotation achieves excellent separation efficiencies for fine coals having only a small fraction of middling particles. However, its efficiency decreases sharply as the concentration of middling particles increases due to the flotation of high-ash particles having a small amount of hydrophobic coal present at the coal surface. Since gravity-based processes are much more efficient at treating middlings, the application of centrifugal washing for fine coal cleaning has been studied with an emphasis on the primary cleaning of fine circuit feed. Results will be shown from a parametric study using a Falcon centrifugal concentrator which reveals that the separation performance is a function of particle size, bowl geometry, feed solids content, and feed rate.

Jan 1, 1994

By Peter Sullivan, Johan van Heerden

Increased use of continuous miners and roadheaders in the underground coal mining industry in South Africa has led to improved productivity and efficiency of operations. Of major concern, however, is the increased amount of airborne dust generated during mining. Dust is a health hazard in terms of respiratory diseases, can impede productivity and is the major contributor to the potential of underground explosions. The concern of the South African coal mining industry with regard to the underground dust problem has led to the establishment of a Dust Control Section in the Coal Mining Division of COMRO. In the field of dust suppression system evaluation and design, collaborative work has been undertaken by COMRO and FLOSEP. This paper gives a review of the application of Computational Fluid Dynamics (CFD) in evaluating and improving environmental conditions in continuous miner and roadheader sections. A brief history of the development of the CFD model as well as a discussion of a typical application is included.

Jan 1, 1993

By Kumara S. Rachamalla

Mineral activity in Ontario represents an annual production in excess of $4 billion. The Ontario government encourages the mining industry to undertake mineral development through grant programs and incentives offered by mineral resource taxation. Computers are playing an increasingly important role in improving productivity in the administration of incentive programs and the Mining Tax Act in Ontario. This has meant speedier processing of grant applications and tax returns which is resulting in a streamlined approach to incentives and taxation in Ontario. The use of computers has resulted in significant contributions to key areas of concern such as assessment of mining tax returns, analysis of the changes, if any, to the Mining Tax Act and modeling of the Ontario Mineral Exploration Program (OMEP). Implementation of state-of-the-art technology such as Local Area Networks (LAN&apos;s), fourth generation languages and integrated micro-mainframe information processing has resulted in improved productivity as well as lower costs. As a result, the respective services provided to the mineral industry by these two programs are now delivered in an efficient and cost-effective manner utilizing the latest available computer technology.

Jan 1, 1986

By H. Maleki

Roof falls continue to affect productivity and safety in U.S. coal mines in spite of significant increases in support utilization in recent decades. To minimize roof stability problems while controlling support effectiveness, the U.S. Bureau of Mines is conducting research on support and ground monitoring techniques. Practical implementation of this research is presented in this paper. Instruments to monitor rock mass deformation, support loads, and microseismic emissions have traditionally been used to assess roof stability. Controlled-source seismic surveys are being used as well. In this paper, measurement techniques are reviewed, and the effectiveness of deformation measurements is demonstrated. This is achieved by an analysis of deformation history from four case studies in room-and-pillar retreat mines. In spite of differences in geologic, geometric, and support conditions in these mines, roof behavior is shown to have been similar prior to failure. The rate of roof movement is suggested as a reliable indicator of roof stability.

Jan 1, 1993

By Walter H. Schwedes

Ore grinding mills are really just slowly rotating barrels, but barrels that are growing in size so fast that the application of electric drives for them is rapidly approaching a technology like that for wind tunnels or pumped storage drives. This application is particularly worthy of care because some 40% of the 75 megawatts of power used by a large copper ore concentrator, or some 60% of the 200 megawatts supplied to a large iron ore concentrator, are for grinding. These ore plants are located where the ore is, not where a utility happens to be. So, the challenge is not only to choose a drive and .power transmission for reasonable cost, high performance, reliability and minimum maintenance, but to afford the interface between mill drive and power distribution and source systems to minimize the whole ore plant&apos;s monthly power bill, or costs of self generation. Conclusions can be reached in optimizing a drive selection only for each particular ore plant&apos;s set of parameters, but by identifying the criteria for selection and then weighting each type of drive per criteria, yardsticks for final choice become apparent. This is the purpose of this paper. Grinding action takes place inside the barrel, where the ore charge is ground with the aid of balls, or mill length rods, or large chunks of ore as in autogenous grinding.

Jan 1, 1972