Search Documents

The inquiry into the explosion at the Moura No. 2 Mine in August 1994 recommended -?Emergency procedures should be exercised at each mine on a systematic basis, the minimum requirement being on an annual basis for each mine.? (Windridge et al. 1996). In December 1996 the ?Approved Standard for the Conduct of Emergency Procedures Exercises? was published and has been subsequently revised (Queensland Department of Mines and Energy Safety and Health Division 1999). This document provided guidelines for conducting mine site emergency exercises as well as the requirement for a test of state-wide emergency response by holding a Level 1 Mine Emergency Exercise at one mine on an annual basis. From 1998 to date (January 2008) ten Level 1 Mine Emergency Exercises have been held in Queensland, Australia. This paper discusses each of the exercises conducted to date as well as the logistics, scenario preparation, planning and organising required to conduct emergency exercises at this level.

Jan 1, 2009

By David R. Delling

Introduction In 1967, Tenneco acquired Kern County Land Co. The primary reason for the acquisition was to obtain Kern's agricultural, manufacturing, and oil interests. Included in the Kern portfolio were the core of Tenneco's present sodium leases in Sweetwater County, WY. This lease base has been ex¬panded and now consists of 62 km2 (24 sq miles). Beneath this property lies more than 500 Mt (550 million st) of economic trona ore. Following the Kern acquisition, Tenneco continued exploration and feasibility studies concerning the trona leases. The effort was accelerated in 1976. Tenneco was attracted to trona because of the favorable lease position it held, the growth rate of the Wyoming industry during the 1960s and 1970s, and the prospects for a long-term, stable business enterprise. The reserve picture was certainly attractive to a company long accustomed to the never-ending struggle to replace oil and gas reserves. In 1978, Wyoming was a boom area that had experienced rapid growth for a number of years. Unemployment was very low and vacant housing nonexistent. The prospects for soda ash were somewhat different in the 1970s than now. But it was recognized even then that a new producer would have a challenging task to compete in this business. Tenneco knew the capital burden required to build a grassroots facility during inflationary time, would have to be offset elsewhere Since labor and energy are the dominant direct costs in mining trona and producing soda ash these factors have always received a great deal of attention. Contracting and permits Environmental monitoring on the site began in late 1977. With the already mentioned considerations in mind, engineering began by mid-1978. Brown & Root Inc. was selected as the general contractor for the project. S. A. Scott & Co. was the engineering subcontractor for the mine shafts, hoists, ventilation system, and miscellaneous mine facilities. Frontier-Kemper was awarded the contract for sinking the two mine shafts. Acquisition of numerous federal, state, and local permits occupied all of 1978 and 1979. The Wyoming Industrial Siting Permit, which addresses socioeconomic issues, drew the most public interest. Siting issues were all satisfactorily resolved by negotiating reasonable stipulations with various local governmental units, school districts, and the like. Site location The Green River project location is not truly remote. It is located within 5 km (3 miles) of Interstate 80 and only about 32 km (20 miles) west of the city of Green River. Nevertheless, a substantial investment had to be made in communication and utility links to the site. These included: • A 14-km (8.5-mile) rail spur connecting with the Union Pacific Railroad at Bryan, WY. This spur has four bridge structures including one crossing Interstate 80. Most soda ash is shipped by rail, and coal is received over this line as well. • A paved 5-km (3-mile) roadway connecting to Interstate 80. • A powerline extension of about 27 km (16.5 miles), along with two new substations. • A 24-km (15-mile) waterline connecting the plant to a pump station on the Green River. The site is located on gently sloping terrain at an elevation of about 2.1 km (6800 ft). Ground conditions are good for construction. Weathered bedrock lies near the surface in most places. Geology The general geology of the Green River Basin has been well described previously. Tenneco's ore is in several superimposed evaporate beds. But the bulk of it is present in Bed 17, located about 457 m

Jan 10, 1985

By David R. Delling

Tenneco is a large, diversified, energy-based company which has grown rapidly during its forty year life. We're the youngest corporation among Fortune's top 20 companies. Tenneco Minerals Company is the division of the Corporation responsible for nonfuel minerals exploration, development and operations. Tenneco Minerals Company is headquartered in Lakewood, Colorado. Exploration offices are in Colorado, Nevada, Alaska, and Perth, Australia. We currently operate two gold mines in Nevada and a large underground trona mine and soda ash processing plant in Wyoming. The latter has a capacity of 907 000 tonnes per year of soda ash and is the subject of my presentation today.

Jan 1, 1984

By Robert C. Freas

The summer joint meeting of the East Tennessee and Carolinas Sections of SME was held in Morristown, TN, on July 29 and 30, 1994. The Friday portion of the meeting began with a field trip to Asarco Inc.'s Young Mine and Mill, one of four mines operated by the company in the Mascot-Jefferson City district. The Young Mill processes ore from two other mines as well as its own, first by heavy media separation and then by standard flotation processes. Zinc concentrates are shipped by truck and barge to an electrolytic refinery in Clarksville, TN. The heavy media rejects and the dolomitic limestone tailings are sold through Asarco subsidiary American Limestone Co. Saturday's technical session, organized by Program Chairman Bob Fulweiler of the Tennessee Division of Geology, provided a review and status report of the zinc industry in Tennessee. This article summarizes papers presented, including one on recent developments in underground blasting.

Jan 1, 1994

Mine Terex articulated dump trucks are working on a large restoration project of an abandoned open cast coal site in Blacklaw, central Scotland. The project is part of the construction of a 42-turbine wind farm complex. During the scheduled 18-month duration of the project, three 28-t(31-st) Generation 7 TA30 dump trucks and the six 36.5-t (40-st) TA40articulated trucks are estimated to move about 1Mm3 (1.3 million cu yd)of material. The trucks are working12-hour shifts, 5.5days a week.

Jan 1, 2005

By E. J. Wasp

An upsurge of interest in slurry pipelines to move coal from Wyoming, Montana, and Colorado to markets in the southwest, west, midwest and northwest has recently developed. Specific pipelines have been proposed to serve these markets; the routes of these lines are depicted in Exhibit I. It is, therefore, timely to discuss some technical aspects of the terminal facilities for these western coal pipelines. The discussion will be based on experience with the Ohio and Black Mesa pipelines as well as detailed planning and testing for a proposed 1,000-mile system from Wyoming to the middle south area. The economics of the pipeline terminal processes are heavily depend¬ent on site, type of process used, and other specifics of the situation. However, the following approximate breakdown of costs for a 1,000 mile, large capacity pipeline will be useful for orientation purposes. [Water supply 4 Coal cleaning 5 Feed preparation 10 Slurry transportation 72 Dewatering terminal 9 100%]

Jan 1, 1976

By L. D. Bowerman

The topic of the presentation will be the excavation of 25,000 IF, 11-foot 0-inch diameter, hard rock tunnel using a Robbins boring machine on the Terror Lake Hydroelectric Project on Kodiak Island, Alaska. This tunnel was completed on a tight construction schedule under some unusual conditions. The tunnel was mined through hard massive granite with faults and high water flows up to 7,000 GPM encountered at the heading in some areas. New innovations in equipment and cutter design were used.

Jan 1, 1985

By A. Dale Wunderlich

Since Sept. 11, 2001, the author has been asked by several mining companies and mining publications to share some of his insights on how the terrorist attacks on the World Trade Center (WTC) and Pentagon might affect the mining industry globally. Until now, the author has been reluctant to express his thoughts in a publication that could possibly fall into the hands of terrorists and give them some ideas that they may not have been previously considering. However, the author discussed the contents of this article with several friends and acquaintances in the international intelligence community. They said that nothing commented on here is new to the terrorists. Potential terrorist targets Sources within the worldwide intelligence gathering community have told the author that current intelligence data indicates that it is likely that the Islamic fundamentalist groups responsible for the attacks on Sept. 11, 2001will likely be directing their effort at foreign business entities. Any overseas or any domestic businesses of highly visible companies that are part of the anti-terrorism alliance should consider themselves a potential target.

Jan 1, 2002

By James L. Vanderbeek

The Chino concentrator commenced operation in 1982 as a SAG-ball mill circuit which could process 37,500 stpd of ore. Since 1982, a series of process improvements such as the addition of two stages of SAG recycle crushing, allowed throughputs to increase to more than 48,000 stpd, at the expense of significantly coarser flotation feed sizing and reduced recovery. To compensate a third (tertiary) stage of grinding consisting of four 1250 hp Vertimills was installed which has allowed the flotation feed size and recovery to return to historical levels. The design and operational characteristics of the Tertiary Grinding Circuit are described.

Jan 1, 1998

By Borje Bjorkvall

At LKAB's plants in Lappland, Sweden, sintered pellets are manu-factured according to three different industrial processes, viz. shaft furnace at Malmberget, straight-grate at Kiruna and grate-kiln at Svappavaara. At present the total annual capacity amounts to 4.7 million tons. However, since it has been decided to erect a new straight-grate plant (2.5 million tons) at Malmberget, and because of the decision to extend and rebuild the existing plants, it is estimated that the annual capacity will be increased to somewhat over 8 million tons by 1973. The great majority of the pellets produced is exported. They are thus reloaded several times and generally speaking roughly handled, resulting in larger or smaller product losses on arrival at the point of use. It is there-fore of great economical interest to have a good control over the transport strength of the pellets by appropriate quality testing at the point of production. In addition to good transport strength, further demands are ob-viously made on pellets destined for blast furnace operation. The blast furnace burden must maintain a good permeability for the gas. The pellets must thus have a favourable size distribution and must not be so weakened by reduction that they disintegrate under the stresses and clog the blast furnace shaft. Furthermore, the burden must have good reducibility. An increase of the rate of reduction can obviously mean increased blast furnace capacity and reduced coke consumption. In order to optimise the properties of the pellets in these respects, the producer must also be thoroughly familiar with their behaviour during reduction, particularly as the customer's interest in the reduction properties of the pellets' has increased over the last few years. Up to now the only quality demands the customer has made have generally had to do with the cold strength and the screen analysis. Thus a quality control of in addition to good transport strength, further demands are obviously made on pellets destined for blast furnace operation. The blast furnace burden must maintain a good permeability for the gas. The pellets must thus have a favourable size distribution and must not be so weakened by reduction that they disintegrate under the stresses and clog the blast furnace shaft. Furthermore, the burden must have good reducibility. An increase of the rate of reduction can obviously mean increased blast furnace capacity and reduced coke consumption. In order to optimise the properties of the pellets in these respects, the producer must also be thoroughly familiar with their behaviour during reduction, particularly as the customer's interest in the reduction properties of the pellets' has increased over the last few years. Up to now the only quality demands the customer has made have generally had to do with the cold strength and the screen analysis. Thus a quality control of

Jan 1, 1972

By J. W. Shuster

Test of trolley-diesel prime power is another step in the search to exploit the unused potential of electric wheel driven haulage trucks. The output of the present engine - a 700 horsepower diesel - is not adequate to exploit fully the 1200 horsepower potential of the two electric wheel drive motors. Power was supplied to a modified 100-ton haulage truck through a double wire trolley system. The vehicle was tested with various payloads on a 7% adverse grade haul road. More significant conclusions developed are: Power - Horsepower to propel the vehicle can he more than doubled to improve truck cycle time. Productivity - Trolley power up adverse grades can improve [producivity] rates from 18 to 36%, dependent upon haul road profile.

Jan 1, 1968

By R. Bruno

The problem of testing different production strategies has been studied in relation to reserves selection and a computer programme for ore production management has been developed. The case study presented concerns an underground rock salt mine in Sicily with different product lines and variable ore characteristics. A geostatistical block model of the deposit was constructed on the basis of the physical and chemical parameters that ultimately determine the type of end-product in operations according to different selection strategies were simulated using the model and taking account of both technical and 'commercial constraints. The structure of an ore production management programme running on a PC to select both the mining unit and the end-use of the ore is described.

Jan 1, 1989

By K. M. Mohamed, R. K. Zipf

The shear strength properties of generic cement foam material and cement foam/concrete interfaces were examined at three testing scales. In laboratory direct shear tests on specimens with average shearing area of 0.006 m2 (10 in.2), the cement foam material had average peak and residual shear strengths of 0.88 MPa (128 psi) and 0.39 MPa (56 psi), respectively. Depending on the concrete strength, the cement foam/concrete interfaces had peak and residual shear strengths ranging from 0.71 to 0.81 MPa (103 to 117 psi) and from 0.27 to 0.29 MPa (39 to 42 psi), respectively. In laboratory direct double shear tests on specimens with average shearing area of 0.084 m2 (130 in.2), the cement foam/concrete interfaces had average peak and residual shear strengths of 0.17 to 0.30 MPa (25 to 44 psi) and of 0.11 to 0.23 MPa (16 to 33 psi), respectively. In large shear tests of simulated cement foam seals with the Mine Roof Simulator (MRS) test frame, cement foam/concrete interfaces with shearing area of 1.486 m2 (2,304 in.2) had average shear strengths of about 0.08 and 0.16 MPa (11 and 23 psi) along the roof and floor interfaces, respectively. The average shear strength through the cement foam material was 0.38 MPa (55.3 psi). Finite element analysis of the large seal tests and the back analysis of the shear strength of full-scale cement foam seals conducted at the NIOSH Lake Lynn Laboratory confirmed shear strength of about 0.14 MPa (20 psi) along the seal/rock interfaces. The study concluded that the structural analysis of cement foam seals should be based on their residual shear strength determined from small laboratoryscale tests of the cement foam/concrete or rock interface and not be based on their peak strength.

Jan 1, 2014

By F. C. Bond

Nature of Empirical Calculations The size reduction of large tonnages of ore and rock is an operation of great magnitude. It is a necessary and important part of industry. Its development has been motivated by practical need and has followed the path of an industrial art without much help from theoretical science. Knowledge has been accumulated from experience. Trial and error established the methods; then collected data were tabulated and served as the basis for empirical equations that have been continually modi¬fied and amplified as new data became available. These equations now constitute the bulk of our present knowledge of comminution. There is no accepted scientific theory that is basic to comminution. In electrical, mechanical, and civil engineering, as well as in many other industrial activities, such theories exist and are extremely help¬ful, but rock is essentially heterogeneous, and the zones of weakness that control its breakage are thoroughly diversified. No theory has yet been discovered which can account for the variability of rock, although many attempts have been made. Empirical equations tell nothing of the why of a phenomenon, but if they are properly derived they can tell much about the how. They always represent only an approximation of behavior but never a law. In a proper empirical equation a symbol is assigned for each of the variable quantities that obviously affect the relationship. In a grinding mill these include mill diameter, mill speed, and feed rate among them. In setting up and revising an empirical equation the cardinal princi¬ple in establishing and modifying it is this: any change must be strictly ascribed to the variable which caused it. A useful empirical equation is rendered useless when a change in any convenient coefficient or exponent is made to make it fit a particular set of data, without certainty that the altered coefficient or exponent is the responsible variable in the new data. Such indiscriminate revisions have brought the use of empirical equations into some disrepute. When existing equations are changed to accommodate new data it is a good rule to make a change which gives results intermediate between the new and the old. A halfway point is usually a good choice.

Jan 1, 1985

By D. Armour, E. R. Bauer, D. R. Zuchelli, T. M. Durr, E. R. Reeves

A team of noise specialists from the National Institute for Occupational Safety and Health (NIOSH), Mine Safety and Health Administration (MSHA), and Joy Manufacturing attempted to evaluate an engineering noise control on a Joy longwall stageloader. The team developed and executed a test plan to evaluate the noise attenuation of the engineering control in an underground coal-mining environment. An evaluation of the long-term noise effects and durability of the engineering control were also a focus of the research effort. Pre- and postcontrol measurements consisting of a combination of worker dosimetry and task observations, tape recordings, and sound level measurements were used to evaluate the engineering control. A description of the engineering noise control, pre- and post-control sound level measurements, and an evaluation of control success is presented. In the end, no evaluation was possible due to mining practices, miner task variations, and inconclusive data.

Jan 1, 2005

By Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) in partnership with Strata Products tested the sealing capability of Ventstop®? as part of an ongoing mine fire control and suppression research program. Ventstop®? is a multi-purpose, inflatable device that is produced by Minvent Solutions and is available world wide for use in the metal and nonmetal mining industry. Ventstop®? is also used in the Australian coal industry as a temporary ventilation control device. The device can be quickly deployed, is reusable and can be placed in horizontal and vertical mine voids to control dust, fumes and smoke. Deployment, multi-day inflation and air leakage tests were conducted at the NIOSH Lake Lynn Laboratory to determine the capability and limitations of Ventstop®? in a simulated coal mine setting. During the tests, Ventstop®? was also subjected to low level forces of a nearby methane gas ignition. It is thought that Ventstop®? could be used by the US coal mining industry to temporarily close an underground mine area in response to a fire or spontaneous combustion heating event, to temporarily redirect mine ventilation during longwall equipment moves or during stopping construction. This paper describes this inflatable temporary mine sealing technology and presents the results of the NIOSH tests.

Jan 1, 2009

By Pradip

The selection, testing, and commercial utilization of flotation reagents is best carried out in stages through microflotation tests on pure minerals and their synthetic mixtures followed by bench-scale batch flotation tests on the ore. A systematic approach to quantitatively evaluate different reagents, in particular, through the analysis of batch flotation data, has been presented in this paper. It is recommended that the reagents are compared both in terms of their performance with respect to the recovery-time as well as the recovery-grade plots. While the former describes the kinetic aspects of reagent interaction, the latter is a measure of its selectivity for a particular separation problem.

Jan 1, 1987

By C. E. Semler

A multiyear program involving online, in-vessel exposures at Barrick Goldstrike Mines Inc. (BGMI) has provided information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products was evaluated. Properties before and after exposure were used to document the performance. Some benefits include the development of a new silicate mortar, a better understanding of brick requirements and increased autoclave operating time between maintenance shutdowns. BGMI operates six pressure oxidation autoclaves at its Eureka County, NV gold operation. These autoclave process 15.8 k/ld (17,500 stpd) of gold ore. Figure 1 is a flowsheet of the six autoclave circuits. The gold ore is refractory, in which the gold particles are mineralogically encapsulated on a micro- and submicroscopic level. The autoclaves are 4.4- m- (14-ft-) diam and 26 m (85 ft) long (tip-to-tip). Inside of each is a full brickwork (brick plus mortar) lining that divides the vessel into five compartments. Each compartment has a motor-driven agitator that keeps the slurry suspended and disperses the oxygen to enhance reaction. During autoclave operation, the conditions are steady state at 210° to 232° C (410° to 450° F) and 61 to 62 kPa (420-430 psi). As shown in Fig. 1, there are other accessory vessels (splash and flash towers) in the autoclave circuits that are also brickwork-lined. The linings used to date, other than small test sections, have all been acid-resistant fireclay bricks, bonded with alkali silicate mortar, PbO- based mortar and/or vinyl ester mortar, but mainly alkali silicate mortar.

Jan 1, 1997

In practice, frothers are selected following general guidenlies and verification by laboratory and/or plant flotation tests. The terms “powerful” or “selective,” which are commonly used to characetrize frothers, have intuitive rather than scientific meaning. A research program has been set out to study fundamental properties of the flotation frothers and to identify the tests which can provide information needed to characterize and classify such flotation agents.

Jan 1, 2004

By D. J. Barratt

The application of autogenous and semi-autogenous grinding circuits in recent years has contributed toward substantial savings in capital and operating costs compared to conventional circuits, particularly for large scale copper and molybdenum operations. Such savings have been realized from the deletion of operating, maintenance, equipment purchase and substantial civil/structural costs associated with secondary-/tertiary crushing and screening, fine ore storage and conveying. In spite of the downturn in the copper- moly industry in North America, there is still an interest in autogenous and semi-autogenous grincting for copper-zinc, gold and silver ores and in the overseas market. Both single-stage and two-stage circuits are in operation. Primary circuits operate autogenously or semi-autogenously in either open or closed-circuit. Critical sizes are extracted and crushed for recycle in some cases (e.g. ABC circuit). Secondary grinding is conducted using ball mills or pebble mills.

Jan 1, 1985