Search Documents

By D. M. Avant, A. J. Solomon, S. M. Pickering, W. R. Fox

Introduction Most high purity silica is produced from crystalline quartz, generally from sand. However, there is a small area of southern Illinois where a porous, friable white chert rock is found that is very different in physical form from quartz sand. This microcrystalline material, commonly referred to as tripoli, is more easily ground to micron sizes than sand. Although of similar Moh's hardness, microcrystalline tripoli is less abrasive than either ground quartz sand or many synthetic abrasives. Location The southwestern corner of Illinois is underlain by extensive deposits of very porous chert; in some places the material is quite white. Two companies, Illinois Minerals Co. and Tammsco Inc., mine and process this white material. The Illinois Minerals plant is located at Elco, and the Tammsco plant is in Tamms, IL. Both companies mine from various locations within a 10-mile truck haul of their plants. Production from this district has been continuous since at least 1915. Malvern Minerals Co. mines and processes a generally similar microcrystalline, friable novaculite near Hot Springs, AR. Geology The southern Illinois white tripoli area is on the southern flank of the Illinois Basin. The commercial silica zone is a facies of the Clear Creek chert of Lower Devonian Age. To the north, where it occurs deep in the basin, the Clear Creek is a siliceous limestone. In the mining area, thin overburden has allowed access by surface ground water, which has leached away the carbonate content and left a quite pure silica residue. Fossils characteristic of sea bottom deposition, such as brachiopods and trilobites, are occasionally encountered in mining. The structure of the mining area is poorly known, due to infrequent outcrops. Strata in most mines are inclined at dips of 5° to 20°. There appear to be occasional high angle normal and reverse faults, but these are seldom of any significance in mining. The friable white silica zone mined in the Clear Creek chert is overlain by dark brownish-red chert and siliceous shale. Exploration drilling to date has not encountered the base of the microcrystalline tripolitic zone. Chemical content Leaching by ground water solution has removed virtually all the carbonate from the original siliceous limestone. Impurities encountered are red to yellow iron oxides, aluminous clays, and occasional black manganese oxides. The silica has no detectable formula water. A typical chemical analysis and physical properties are listed in Tables 1 and 2. Mineralogy and crystallinity Southern Illinois friable tripoli appears amorphous under the polarizing microscope. No crystal structure and only occasional, vague, patchy anisotropism is evident. However, the material gives an excellent quartz X-ray diffraction pattern. Thus, so far as X-ray mineralogy is concerned, the material is clearly

Jan 12, 1986

By K. Mulukhov

Introduction The depth of open-pit mines continues to increase. The typical designed depth for large quarries is now in the 300 to 600 m (1,000 to 2,000 ft) range, with some quarries even reaching depths of 700 to 800 m (2,300 to 2,600 ft). The cost of handling material from such deep mines can be 60% to 70% of the total cost. The capacity of using a cyclic means of transport, such as trucks or skip hoists, continues to drop as the depth of the mine increases. In addition to the problem of maintaining relatively low slope angles for haul roads, increases in environment pollution and increased fuel consumption make the use of trucks ineffective below 100 to 150 m (300 to 500 ft). In handling large quantities of bulky materials, i.e., more than 15 to 20 Mt/a (16 to 22 million stpy), under fixed terminal points, belt conveyors are preferable in almost in all cases. An exception is when the lump size of the load is too high for the conveyor to handle. Belt conveyors in mines can handle loads having a maximum lump size of no more than 250 to 300 mm (10 to 12 in.). The use of a movable crusher prior to the belt conveyor in an open-pit mine would make the process very expensive. Such an operation could not compete with truck haulage on a cost basis. Belt-car conveyor The main factor that restricts the lump size for conventional belt conveyors is collision impacts between the load-carrying belt and idlers. These impacts are completely eliminated in the belt-car conveyor, which was previously described by Mulukhov (1977). The unique feature of the conveyor is that the load-carrying belt is supported by moving cars. Each car consists of a troughed cross strap that supports the belt with the load and two rollers, on which the cars move along upper and lower rails. Cars are connected by two endless chains revolving over sprockets. The system uses conventional drive pulleys, tail pulleys and return idlers. There are no fasteners between the carrying belt and the car cross straps. The conveyor belt simply drives the cars along by the force of friction between the belt and the straps. A belt-car conveyor was first installed in 1970 at the Karatau mining operation in Kazakhstan. The system was an elevating conveyor with an inclination of 20° and was located on the final part of the truck haul road. The conveyor transferred blasting phosphate ore from the quarry to the crushing plant. A bunker was mounted between the trucks and the conveyor. The maximum lump size was typically 1,200 mm (48 in.). However, there were some lumps as large as 1,500mm (60 in.), which was greater than even the belt width (Fig. 1). Because the prototype belt-car conveyor was intended only for industrial trails, it had a relatively short length of about 50 m (160 ft). Nevertheless, the conveyor yielded a substantial profit over the cost of truck haulage. Naturally, the first question one might ask is why such a system is not now widely used. The reason was the further development of a huge transporting complex for the whole quarry at the base of the belt-car conveyor. After successful industrial trials from 1971 through 1973, which demonstrated the systems engineering feasibility, the State Planning Committee of the USSR included the development of the belt-car conveyor in its plan for the development of the national economy. However, mistakes were made. First, a single organization was not in charge of the development. Second, a plant that was not specialized in belt conveyors was put in charge of the design and manufacturing of the conveyor system. In addition, the crusher was installed before the stacker, which negated the major advantages of the belt-car conveyor. For loading the conveyor, a special blade feeder with pendulum suspension was developed, but it was found unreliable. The main conclusion was that, in-

Jan 1, 2003

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

By F. D. Mendes, A. H. Martins

The high copper grade in the Igarapé Bahia (Brazil) gold-copper ore restricts the direct application of the classical cyanidation process. Copper oxide and sulfide minerals react with cyanides in solution, causing high leach-reagent consumption, raising processing costs and decreasing gold recovery. According to studies, a feasible solution would be to pretreat the ore to remove copper minerals prior to cyanidation. The goal of this experimental work was to study the conditions for the removal of copper from the Igarapé Bahia gold-copper ore by sulfuric acid leaching, applying a statistical approach to the experimental design. By using the Plackett Burman method, it was possible to select the variables that exhibited the largest influence on copper extraction at the sulfuric acid leaching stage. These variables were leach solution temperature, stirring speed, sulfuric acid concentration in the leach solution and ore particle size. The individual effect of these variables and their interaction influences on the experimental response were analyzed by applying the replicated full-factorial design method. Finally, the selected variables were optimized by the ascending-path statistical method, which determined the best leach experimental conditions for maximum copper extraction. The optimized leaching conditions resulted in a copper extraction of 75.5%. Keywords: Copper, Gold, Extraction, Sulfuric leaching, Optimization

Jan 1, 2003

By V. B. Achanti, A. W. Khair

Developing a laboratory procedure for the determination of coal-seam compressive strength has been a subject of discussion for many decades, and the reliability of laboratory determinations is often the subject of debate. A coal seam’s characteristics, the method of sample collection, the specimen preparation method and the testing procedure can often result in drastic variations in the test results. In this paper, the development of a laboratory testing procedure for the determination of coal-seam compressive strength is presented. Two samples that were collected from different coal seams were tested in this study. First, the inherent characteristics, i.e., coal structure. Hardgrove grindability index (HGI), Slake durability index, proximate analysis and mechanical properties (Young's modules and Poisson's ratio), of each coal were determined. The results were used to categorize the coal scams in terms of the characteristics liable to produce variable strength data in typical laboratory tests. Second, two commonly used laboratory specimen shapes, cylindrical and cubical, were tested to determine which shape produced the most reproducible strength values. Third, four loading rates within the static testing range, i.e., 0.007, 0.07, 0.34 and 0.7 MPa/s (1.0, 10, 50 and 100 psi/sec), were used to determine the ideal loading rate. Finally, the number of test samples required to produce strength data within the acceptable standard deviation, considering coal seam characteristics, were established. Background Laboratory testing of coal specimens for the determination of seam compressive strength has been a subject of discussion since the early 1900s. Many researchers have tested coal specimens to estimate coal-seam compressive strength for use in pillar design to insure the safe operation of [ ] mines (Unrug et al., 1986; and Hirt et al.. 1992). Yet, there is a lack of a universal procedure, and, no matter which approach is used, it becomes the subject of intensive debate. A great deal of work has been performed on the subject, and there is much information available in the literature. Some of this work concerns quantifying the influence of specimen shape and size on compressive strength (Bieniawski. 1968: Barron et al.. 1992: Khair and Xu 1994; and Khair 1994). As indicted in the literature, coal is a heterogeneous material, consisting of discontinuities such as cleats and bedding planes, which are likely to produce variable strength results (Holland, 1964; Unrug et al., 1986). Some of the prominent issues that influence the determination of coal-seam compressive strength in the laboratory are: •the collection of a representative sample from a coal seam; •the geometry, i.e., shape and size of the specimens to be prepared and tested: •the loading rate at which the specimens are to be tested:

Jan 1, 1997

By R. K. Mehta, C. W. Schultz, J. B. Bates

Introduction The Mineral Resources Institute, The University of Alabama, has for the past three years been engaged in a program to develop a beneficiation system for eastern (Devonian) oil shales. One objective of that program was to evaluate advanced technologies for effecting a kerogen-mineral matter separation. Column flotation was among the advanced technologies selected for evaluation. Early in the program it was shown that column flotation was superior to conventional (mechanical) flotation and to the other advanced technologies being evaluated. The investigation then proceeded toward the further objective of defining the optimum operating conditions for column flotation. One observation made in the course of optimization testing was that introducing the feed into the froth (above the pulp-froth interface) resulted in an improved combination of concentrate grade and kerogen recovery. This observation was reported in a previous paper (Schultz and Bates, 1989). Because the practice of maintaining the pulp froth interface below the feed point is contrary to "conventional" practice, it was decided to subject the observation to a systematic series of tests. This paper describes a recent series of tests and the results that were obtained. Experimental equipment and procedure The arrangement of the column cell and auxiliary equipment for continuous flow testing is shown schematically in Fig. 1. The feed sump [O] is filled with a sufficient volume of prepared sample to permit a large number of tests to be performed (typically 12). Past experience has shown this is necessary to control sample variability and variability in the size distribution resulting from ultra fine grinding. The feed slurry is maintained at about 20% solids and is constantly recirculated and stirred. The sample is metered from the circulating pipe by a peristaltic pump [O]. The feed slurry is diluted with reagentized water [O] by a second peristaltic pump [O]. Wash water [O], also reagentized, is supplied through a third peristaltic pump [O]. While this feed system may seem unduly complex, it does permit users to independently vary either the wash water rate or the net solids content of the cell. In the tests reported here, the feed rate and net percent solids were constant at 12.5 gms/min. and 3.3%, respectively. Diluted feed enters the column through 6.35 mm-diam (0.25 in.-diam) copper tubing and is discharged upwardly at the center of the column. Tailings are discharged through flexible tubing that can be adjusted so as to control the position of the pulp-froth interface. The column is 76.2 mm-internal-diam (3 in.-internal-diam) and 1090 mm (43 in.) high. It is made from lucite tubing and is fitted with a 51-mm-diam (2-in.-diam) fritted glass air sparger having an average pore diameter of 50 µm. In performing a series of tests, the concentrate and tailing are allowed to discharge continuously. The system is allowed to equilibrate for 30 minutes after the pulp and froth reach operating levels. Concentrate and tailing samples are taken simultaneously for timed intervals (five to 15 minutes, depending on the volume of sample desired). After sampling, a change in operating conditions is made and the system is again allowed to equilibrate. The tests to determine the effect of the pulp-froth interface level were part of a larger series of tests in which the objective was to optimize the conditions for a rougher flotation stage in a two stage circuit. The sample used in this series of tests was an Alabama shale ground to d90 = 23.1 µm and d50 = 7.9 µm. The operating conditions remaining constant in this series of tests were as follows: Column height - 1600 mm (63 in.) Air sparser - 50 µm (average pore diameter) Spray water - 130 cc/min. Feed rate - 12.5 gm/min (0.4 oz per min) (dry solids) Percent solids - 3.3% Frother (Dowfroth 250) - 45 ppm The variable test conditions are tabulated in Table 1. Positions of the pulp level (pulp froth interface) and feed entry are presented as a percentage of column height (as measured from the face of the air sparser). These test conditions are presented Fig. 2. At each of these test conditions, individual tests were performed at varying air

Jan 1, 1992

Gold heap leach operations often process low grade ores with little margin for cost increases. The advantage of heap leach operations is the considerable savings in both capital and operating costs. This paper looks at an alternative pH modifier to lime in the heap leach process, namely bauxite waste mud or red mud. The red mud can contain trace amounts of gold and was found to be an excellent source of slow release sodium hydroxide for long-term pH modification. Column cyanide leaches showed that 25 kgt-1 of red mud provided a higher pH and longer pH modification than 0.25 kgt-1 of lime. Contaminants leached from the red mud hampered the adsorption of the aurocyanide complex onto activated carbon.

Jan 1, 1993

By R. H. Parker, B. A. Wills, D. G. Binns

Introduction With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the fine mineral particles in these ores. Not only is this expensive, but it leads to greater losses in slimes. Gravity concentration techniques become unacceptably inefficient for particle treatment below 25 to 50 µm, and even flotation fails in the ultra-fine range. Ore from the South Crofty mine near Redruth, Cornwall, was subjected to thermal pretreatment in the hope that differential thermal expansion of the minerals would lead to intergranular cracking, and thus enhanced liberation. South Crofty ore contains about 1% tin as cassiterite associated with a complex assemblage of quartz, chlorite, tourmaline, and hema¬tite in granite and slate. Recovery of cassiterite can be as low as 70%, as overgrinding occurs during stage reduction of the material to 1 mm (primary grinding) and 180 µm (regrinding). Cassiterite is present in grain sizes ranging from submicroscopic to + 10 mm, the bulk being predominantly in the range of 50 µm to 3 mm. Experimental Flat polished sections of the ore were photographed in reflected light using a Vickers M17 microscope. The sections were then heated in a Carbolite LMF4 muffle furnace. The heating rate and temperature were monitored by a thermocouple immersed in the bed of particles. Previous work by Sherring (1981) on the same material showed that a 55% reduction in grinding resistance occurred when the material was rapidly heated and cooled through the quartz inversion tem¬perature (573°C), where a volumetric expansion of 0.86% occurs. The samples were therefore heated to 650°C at 26°/min, and were then water-quenched to room temperature. The effect of heat treatment on the mineralogy and fracture network was assessed by examining the same area after treatment. Results Most of the sections examined showed that extensive transgranular cracking occurred as a result of heat treatment. Such cracking, although weakening the rock and hence reducing the work index, would in no way enhance the liberation of the cassiterite from the host minerals. Intergranular cracking, which would lead to enhanced liberation, was difficult to discern under reflected light, but there was evidence of such cracking in some of the sections examined. Figures 1 and 2 are examples of typical sections before and after heat treatment. Figures la and lb - show cassiterite in hematite, Fig. lb, in normal incident illumination, illustrating clearly that after heat treatment, transgranular fracture is evident in the cassiterite. If any intergranular cracking has occurred, it is not evident in this photograph. Figures 2a and 2b show cassiterite in quartz before and after treatment. Fracturing in both minerals after treatment can clearly be seen, and there is evidence of intergranular fracturing. However, protruding "arms" of cassiterite are severed by transgranular fracture. Subgrains of quartz have also been isolated by trans¬granular fracture. There is major transgranular cracking across the wider sections of cassiterite. Discussion The effect of rapidly heating South Crofty tin ore to 650°C, followed by water-quenching to room temperature, has been studied by observing the fracture networks in mineral grains. The choice of 650°C as the heating temperature was influenced by the work of Sherring (1981), who found considerable reduction in grinding resistance after thermal pretreatment of the same ore. Scheding et al. (1981), however, have shown, by means of a crude calculation, that heat treatment cannot be justified solely on the basis of reduced grinding costs. The cost of heat treatment far out-weighs that of grinding, resulting in the combined costs for heat treatment being over six times that for grinding unheated material. The most economically attractive aspect of heat treatment is the possibility of enhanced liberation of the valuable mineral due to increased intergranular rather than transgranular fracture. Grinding costs would be greatly reduced by improved liberation at coarser sizes, and the costs of ancillary processes, such as dewatering and tailings disposal, would be reduced. The most significant economic effect, however, would be in improved metallurgical efficiency. Improved liberation would increase concentrate grades, and recoveries would be higher, particularly in the case of ores where high slime losses are produced due to the excessively fine grinding required to produce adequate liberation. Manser (1983) has shown that only a 1% increase in tin recovery, at the same concentrate grade, would be sufficient to offset heat treatment costs on South Crofty ore. Heavy liquid analysis and shaking table separation have been used to evaluate the effect of thermal treatment on processing (Binns, 1984; Scheding, 1981; Sherring, 1981). However, treatment of unheated and heated samples of South Crofty ore, ground to the same product size, by such methods have shown little evidence of improved metallurgical efficiency after thermal pretreatment. The large amount of transgranular fracturing revealed by reflected light studies helps to explain this lack of improvement. Nevertheless, from the evidence of some of the fracture work, it is surprising that no improvements in metallurgical

Jan 1, 1988

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24% of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50% of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include • extraction of thick seam in ascending order with stowing ; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving ; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof, four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 3, 1987

By T. B. Szwilski, R. D. Begley

Status of ISO 14000 standards. The ISO 14000 are voluntary international standards providing a frame-work that allows a company to integrate an effective environmental-management system (EMS) into its operations. The purpose of an EMS is to provide a systematic procedure to identify the environmental aspects of a company's activities, evaluate any significant impacts and use the information to set objectives and targets toward continuous improvement of the company's environmental compliance and performance. In addition to the specifications for certification, ISO 14000 can be used as a guide to develop an effective environmental-management system or for self-declaration. The International Organization for Standardization (ISO) is a worldwide federation founded in 1947 to promote the development of international manufacturing, trade and communication standards. The organization is now represented in 118 countries, with the American National Standards Institute (ANSI) representing the United States. The principal goals of the ISO is "to promote the development of standardization and related ac¬tivities in the world with a view toward facilitating the international exchange of goods and services and to develop cooperation in the sphere of intellectual, scientific, technological and economic activity." ISO develops standards with input from government and industry. Because the standards are voluntary, there are no legal requirements to pressure countries to adopt them. However, many governments, industries and US agencies are adopting the ISO standards as a requirement for business trans¬actions, thereby, compelling suppliers to adopt ISO standards. These business and market forces, which are likely to be strategic business issues in the 21st century global marketplace, are imposing the need to develop a systematic approach to environmental management. The ISO 14000 series evolved from a United Nations Conference on the Human Environment in 1972. It includes a broad range of elements: the basic environmental management system, environmental auditing criteria for internal and external auditors, criteria for environmental performance evaluation (EPE), environmental labeling criteria and life-cycle assessment methodologies. The standards comprise two categories: organization evaluation standards and product oriented standards (Table 1). The ISO 14001 specifications contain the requirements for developing an environmental-management system that may be objectively audited for certification. The ISO 14004 standard provides guidance on interpreting the ISO 14000 specifications for the development and implementation of the EMS and for coordination with the management system of the company. On Sept. 1, 1996, the American National Standards Institute (ANSI) and the Registrar Accreditation Board (RAB) signed a formal agreement to create a new entity called the National Accreditation Program (NAP). To obtain certification, a company must fulfill the requirements outlined in ISO 14001. It is required that "a third party give written assurance that a company's EMS meets all the requirements of ISO 14001." Preparing for ISO 14000 can include subscribing to voluntary environmental initiatives; learning from ISO 9000 quality-management experiences; and utilizing information from recognized training courses, publications and numerous Internet resources. Once committed to an EMS, the management should provide sufficient resources to achieve continuous environmental-performance improvement, as outlined in an environmental policy. A thorny issue now being debated concerns the potential liabilities of documenting the environmental performance of a company. General impact of the ISO 14000 EMS standards. With increasing stakeholder awareness, costly end-of-pipe pollution-control approaches and the success of ISO 9000 quality-management standards, the ISO 14000 EMS standards are being adopted by companies and governments worldwide. The United States and Canada have well-established programs. In Europe, countries differ but are firmly committed toward environmental-management standards (BS 7750, EMAS and ISO 14000). The Department of Environmental Protec¬tion of the State of Pennsylvania is using ISO 14000 as a vehicle to develop a closer working relationship with industry, and it is anticipated that this policy will eventually lead to fewer environmental site inspections for those companies with ISO 14001 certification. The Depart-

Jan 1, 1999

By Y. Akin, M. S. Celik, T. Batar, F. Arslan

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, the boron minerals colemanite, ulexite and borax undergo decrepitation, shrinkage and expansion, respectively, upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot-plant studies conducted in our laboratories on the calcination of boron minerals are briefly reviewed and their implications to commercial operations are discussed.

Jan 1, 1999

By L. A. Ruth

Introduction The US Department of Energy's Office of Fossil Energy has begun a new approach for developing the ultra-clean energy plants. This approach will allow the nation to continue to use low-cost fossil fuel feedstocks during the early decades of the 21st century. The new approach is called Vision 21. The overall goal is to effectively eliminate, at competitive costs, environmental concerns associated with the use of fossil fuels for producing electricity and transportation fuels. Vision 21 is based on the following three premises: •The nation will need to rely on fossil fuels for a major share of our energy needs well into the 21st century. •It makes good sense to rely on a diverse mix of energy resources, including coal, gas,

Jan 1, 2003

By J. D. Patsey, G. T. Lineberry

Introduction A computer program was developed for analyzing drum-type hoists before modifying an existing system or designing a new one. Its use permits the preliminary evaluation of a system before seeking technical assistance from mine hoist designers and manufacturers. The user-friendly program accepts a variety of data and analyzes hoisting systems for any balance state. The program can be used to calculate skip capacity to yield a desired production rate, solve for drum face width, select a permissible wire rope, estimate total horsepower of the hoist plant, and estimate annual power cost. Whether required for a large mining complex or for a relatively small operation, a hoisting system must be carefully designed to ensure the efficient, reliable, and safe flow of material. Because shaft sinking and hoist installation can total between 2.5% and 3% of the cost of opening a deep mine, proper hoist selection is critical. Today's mining engineer has at his disposal the most powerful design and analytical aid ever, the microcomputer. There is, unfortunately, limited software for the study of hoisting systems, unlike that for other materials handling equipment (Manula and Albert, 1980; Prelaz et al., 1964; Bucklen, 1969; Thompson, 1985). HOIST reduces a time-consuming set of calculations to a concise package of interrelated subprograms. A literature review revealed no common-user programs to analyze hoisting systems, although at least four major hoist designers/manufacturers/installers have their own in-house programs. To provide a tool with which the mining engineer could preliminarily analyze a materials hoisting system or could check the calculations of a hoist contractor, a computer program was developed. HOIST was written in BASIC for the IBM-PC for ease of program adaptation and to encourage field use on compatible systems. Details of program development are omitted, since the basic principles of hoisting analyses are relatively straightforward, simple, and readily accepted (Harmon, 1973; Nordberg, n.d.; Adler, 1957). Program features, intended usage, and benefits of the computerized solution are emphasized over theory development and mathematical rigor. Background The mine hoist system that is selected and installed at a mine is the "lifeline" of that mine, with installations lasting 20 years or more. Thorough study is warranted to ensure that productivity demands are met at a minimum cost per ton. The increased cost of a large, powerful, high-speed hoist must be offset by increased production to justify its selection. To optimize this tradeoff, an extensive hoisting analysis should be performed. The analyses to properly size the skip (or cage), the drum, and the hoist drive are conducive to computerization, permitting rapid evaluation of changeable operating and design parameters, such as velocity, acceleration, state of balance, and productivity demand. The program is particularly useful in conducting sensitivity trials, such as investigation into the effect of change of productivity on skip capacity and on horsepower of the hoist drive. HOIST is currently limited to the study of drum-type hoists with cylindrical drum(s). However, only minor changes to the program would permit analysis of friction hoists and conical drum configurations. Model development and testing The program is based on accepted equations and physical relationships. Examples of manual calculations formed the basis for decision points and program branching. Data is input in the order that it would be needed if the problems were solved manually. The choices are arranged likewise. HOIST was developed in sections, with manual solutions performed to check program logic. The testing became more rigorous as sections were completed. Output from one section becomes input for following sections, as appropriate. The simplified flow diagram of HOIST is given in Fig. 1.

Jan 2, 1987

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

By M. Liu

The use of surfactants shows great potential for the removal of hydrophobic organics from soils by in-situ washing techniques. Lab-scale soil washing experiments were performed using sodium dodecylsulfate (SDS), an anionic surfactant, and anthracene, a highly hydrophobic compound. The results of this research show that the solubility of anthracene increases linearly with an increase in SDS concentration above the critical micellar concentration. Furthermore, SDS can be effective in removing anthracene from contaminated sand.

Jan 1, 1993

By R. J. Pruett, J. Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1999

By M. J. Sapko

The US Bureau of Mines conducted, through joint funding with the Colorado Mining Association, large scale oil shale rubble fire tests to investigate flammability characteristics and different methods of extinguishment. Ignition of large rubble piles was easily accomplished. Foam blankets could he used to control surface flames. The results of these large scale tests confirmed that water was effective but not particularly efficient in extinguishing deep seated oil shale fires. It took up to 1.7 times as much water to extinguish afire as anticipated on the basis of a simple cooling model, assuming 100% utilization.

Jan 1, 1990

By H. Knorre, A. Griffiths, J. Loroesch

Introduction Hydrogen peroxide is known to the mining industry as a powerful oxidant, able to attack and to destroy cyanide, the most important leaching reagent (Knorre and Griffiths, 1984; Griffiths, 1988; Griffiths, 1988). CN- + H202 => OCN- + H2O The most recent development, however, is the use of H202 as an oxidant in the cyanidation of precious metals. This application may appear to be a contradiction to the above mentioned detoxification process. This can, indeed, be the case if certain conditions are not considered carefully. Degussa has developed a new process to enable the application of H2O2, in this field without having any detrimental effect on the cyanide. The incentive to seek an oxygen supplier like H2O2 instead of air was the fact that one of the most important conditions for the fast dissolution of gold is the presence of physically dissolved oxygen in the pulp (Kydryk and Kellog, 1954; Warstell, 1987). 2 Au + 4CN- + 1 /2 O2 + H2O => 2 [Au(CN)2]- + 2 OH Complete gold recovery within a reasonable leaching time may only be achieved if the pulp is saturated with dissolved oxygen. Gold losses in leach operations mainly occur due to the following reasons: • In some cases, the saturation of oxygen in the pulp cannot be achieved by aeration due to the difficulty to transfer oxygen from the gaseous into the liquid phase. This happens, for example, in pulps with a high viscosity. In such cases, even violent aeration only results in a low concentration of dissolved oxygen in the pulp. • In any case, the starting phase of leaching requires the highest amount of oxygen. Therefore, it is especially important to raise the dissolved oxygen level to saturation in the starting phase. Peroxide assisted leach process (PAL) The intention of the process is to introduce oxygen in a liquid form. As a result of intensive research work, it could be shown that hydrogen peroxide can be used as a source of oxygen in the leaching of gold ores. To avoid side reactions, the following conditions must be applied: • Hydrogen peroxide must be diluted before it is added to the pulp. • The dosage of H2O2, must be properly regulated based on the oxygen level of the pulp. • An important part of the continuous 02-control is a special oxygen electrode, which resists the extremely abrasive action of the pulp.

Jan 1, 1989

By C. J. Johnson, C. J. Bise

Introduction Coal extraction by continuous miners (CM) is currently the most common underground method in the US industry and accounts for slightly more than two-thirds of the nation's deep mining production (National Coal Association, 1987). Even if longwall mining should become more commonplace, it can proceed only after ventilation and access entries have been driven by CMs. Since an area of concern continues to be the effects of the dust generated on the health of mineworkers, this paper discusses the relationship between the elemental compositon of mining-generated airborne dust sampled from the immediate ventilation return of a CM and laboratory-generated dust derived from channel samples taken from the mines. There are several potential contributions of this type of study to the coal mining industry. First, after more fundamental knowledge of the causes of Coal Worker's Pneumoconiosis (CWP) is learned, the laboratory-generated respirable dust could be used to identify a potentially hazardous coal seam. Also, this study could possibly aid in understanding the fundamental causes of CWP by producing mining-simulated samples of coal dust that could be used in epidemiological studies. Further, assuming that there is no difference in the elemental composition of a drill-core sample and a channel sample from the same location, a mining company could predict a new mine's respirable dust elemental composition in the immediate ventilation return by using exploratory drill core samples of the roof, coal, and floor rock to prepare the laboratory dust. Ventilation engineers could then use engineering design and control measures during premine planning to reduce the incidence and severity of CWP by better ventilating the potentially hazardous coal seam. If this proper planning prevented any future changes to the ventilation equipment and mine design, much time and money could be saved. Scope of work To investigate the variability of the chemical characteris tics of respirable dust, airborne dust samples from eight underground coal mines located in the eastern and midwestern United States were collected with eight-stage Sierra Model 298 Marple cascade impactors, as well as 25 channel samples of mined material. Each channel sample was removed from the middle of the coal face before mining occurred. Sampling of the mining-generated dust was conducted by Lee (1986) by sampling the entire working sections, primarily for characterization purposes, to obtain information on the locational variability of dust characteristics. Research performed for this study used the elemental analyses of the mining-generated dusts he sampled in the immediate ventilation returns of CMs. The procedure that was used to produce the laboratory-generated respirable dust was based on the Hardgrove grindability test since it reflects the pulverizing characteristics of coal. This test was chosen for several additional reasons. First, it is repeatable and reproducible. A consistent amount of input energy is used as well as a specified size range of feed material to be crushed (the channel samples). Second, it is thought to generate secondary dust in a way similar to that of the crushing and grinding of the coal and rock as they pass through the arc-shaped cutting path of the CM's cutter head. The potential effect on dust generation by this secondary grinding mechanism may be at least as much as that produced by primary fragmentation, which is dust produced by the cutting action of the bit against the coal or rock (Roepke, 1984). Finally, the Hardgrove grindability test is well known and is used in the coal industry to guide mineral processing engineers in estimating the capacity of mills used to grind coal. One hypothesis of dust researchers in the Generic Technology Center for Respirable Dust is that the elemental as well as the physical characteristics of coal mine dust will make a difference in the incidence and severity of CWP. Coal mine dust is generated not only from coal, but also from any rock partings contained within the seam or any roof or floor material mined with the coal. Thus, coal mine dust may not have the same elemental characteristics as the coal being mined. Given that hypothesis, mixtures proportional to each thickness mined of roof, coal, and floor rock derived from the channel samples of the face areas from which the respirable dusts were generated by the CMs were used to produce the feed material that was pulverized in the Hardgrove machine.

Jan 1, 1989

By K. Hansson, A. Jedborn

Background In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore, from a system's point of view, slurry transporta¬tion would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alterna¬tive examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasi¬biliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. l . The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then tempo¬rarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situ¬ations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe¬line, and personnel are needed. In a first phase (Fig. 2), a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1989